Horizontalios juostinės pjūklai – rankiniai – apvalios pjovimo srities 0–220 mm pirkti naudotą (50)

Būklė: naujas, Gamybos metai: 2026, CORMAK HBS275 Bandsaw for cutting pipes, profiles, and bars is widely used in all locksmith workshops where precision, quality, and cutting speed matter. This model is equipped with a swiveling arm (0-60°), and the saw guides are based on carbide inserts. The frame design ensures precise and quiet operation. Machine Features The horizontal bandsaw for metal with a swiveling arm allows cutting perpendicular to the axis of the material and at any angle from 0 to 60°. Material can be fed manually or by any mechanical device; however, tool feed is automatic. The blade guides are fitted with special carbide plates and bearings. This significantly influences the band guidance, blade life, straightness, accuracy, and cutting quality. Carbide guidance greatly reduces machine and blade wear. The machine is fitted with an efficient coolant pump with a closed-loop cooling system. The saw arm is made from a single-piece cast iron, and with the 27 mm wide cutting blade used in this bandsaw, allows for series cuts of both profiles and solid materials. The vise is placed on an adjustable bed and features a quick-release clamp. The blade guides have hard metal carbide plates and a bearing system. It is specifically THE CARBIDE GUIDES that are responsible for cutting precision and straightness. The arm is fitted with an automatic blade tension sensor and is inclined at 25 degrees, increasing blade life. A cleaning brush is mounted underneath the arm to ensure optimal blade cleanliness and operation. The drive is transmitted via a worm gear. The base is fitted with a cast iron working table with a swiveling arm and a control panel on a separate arm. During cutting, the primary cutting movement is the translation of the blade, while the feed is by the descending arm. The arm descent speed (cutting speed) is adjusted by a hydraulic cylinder. Feed speed is regulated on the control panel. Two cutting speeds are available: 37.5 and 75 m/min. In the arm's lower position (after cutting), the drive to the cutting blade is switched off automatically. Safety is ensured by blade guards and micro-switches that stop the motor after the cutting cycle ends or any guard is opened. Additional protection results from the automatic machine switch-off in the event of a broken blade. The machine drive is transmitted by a motor with a worm gearbox. The motor features a thermal fuse to prevent overheating during operation. Technical Data TOTAL POWER: 1.5 kW POWER SUPPLY: 400V 50Hz ARM DESCENT ADJUSTMENT: hydraulic cylinder BLADE LENGTH: 2450 x 27 x 0.9 mm BLADE SPEED: 37.5 / 75 m/min VISE BASE HEIGHT: 900 mm MACHINE DIMENSIONS (WITH ARM RAISED) (L x W x H): 1720 x 800 x 1800 mm Fpsdpfxoudi Uns Ac Djf WEIGHT: 215 kg ANGLE 0º ø220 260 x 140 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100 The price does not apply to machines purchased in Poland.

Būklė: naujas, Gamybos metai: 2026, Funkcionalumas: visiškai funkcionalus, įėjimo įtampa: 400 V, įvesties srovės tipas: trifazis, valdymo tipas: vadovas, bendras aukštis: 1 900 mm, bendras ilgis: 1 950 mm, bendras plotis: 750 mm, bendras svoris: 230 kg, Įranga: CE žymėjimas, dokumentacija / vadovas, sūkių greitis be galo kintamas, Technical parameters Built-in cooling system: Yes Saw blade size [mm]: 2455 × 27 × 0.9 Blade tension: mechanical (manual) Blade speeds [m/min]: 36, 72 Feed rate [m/min]: 0–50 (stepless) Fpjdpfxsyr Ndhj Ac Djf Saw bow lowering control: stepless – hydraulic cylinder Vice base height [mm]: 1010 Power supply: 3-phase 400 V Motor output [kW]: 1.1 Dimensions [mm]: 1950 × 750 × 1900 Weight [kg]: 230 Warranty: 24 months Operating manual: Polish language CE Declaration of Conformity: Yes Product description The horizontal metal band saw with swivel saw bow enables both perpendicular cutting to the workpiece axis and cutting at any angle within a range of 0° to 60°. The material to be cut can be fed either manually or by any mechanical feeding system, while the saw feed occurs automatically. The blade guides are equipped with special carbide plates and bearings, which significantly affect the guidance of the saw blade, its service life, straightness, as well as the accuracy and quality of the cut. The saw bow features a rigid construction made of profiled cast iron, ensuring high stability and low vibration during cutting. The bow is fitted with a control panel for operating the machine. The drive from the electric motor to the saw blade’s drive wheel is via a worm gear. The saw blade is tensioned over two cast-iron wheels and guided by a manual tensioning mechanism as well as adjustable rolling and sliding carbide blade guides. Inside the machine is a separate coolant tank with an electric pump, increasing the blade’s service life and improving cutting performance. The lowering speed of the saw bow (cutting speed) is regulated by a hydraulic cylinder, while the feed rate is set using the machine’s control panel. Two blade speeds are available: 36 and 72 m/min. When the saw bow reaches its lowest position (after cutting through the material), the saw blade drive is automatically switched off. Safety is ensured by: - Saw blade guards - Microswitches that stop the motor when the cutting cycle is completed or a guard is opened - Automatic machine shut-off in the event of saw blade breakage Application The MTP BS260G band saws are professional machines for cutting: - Steel profiles - Solid material and shafts They are equipped with a hydraulic cylinder, cooling system, and a saw bow that swivels up to 60°. Used with high-quality saw blades from the German manufacturer Roentgen, they ensure precise, fast and clean cuts. The machine is ideal for cutting: - Carbon steel - Alloy steel - Structural steel - Stainless steel - Acid-resistant steel Delivery to the customer is possible. Shipping costs are calculated individually by the transport company.

Būklė: naujas, Pjovimo diapazonas 90°: apvalus 115 mm Pjovimo diapazonas 90°: plokščias 100 x 150 mm Juostinio pjūklo matmenys: 1638 x 13 x 0,65 mm Juostinio pjūklo greitis: 20/29/50 m/min Fsdpfeyy A Rfjx Ac Dspf

Būklė: naujas, įėjimo įtampa: 400 V, valdymo tipas: vadovas, bendras svoris: 85 kg, Įranga: CE žymėjimas, Simple, ergonomic and economical metal band saw EBS 128 CL BERNARDO. Angle cutting possible from -60° to +45° by adjusting the saw arm, with a cutting range at 90° up to 125 mm (flat workpiece up to 150x100 mm). Besides changing the cutting angle using the saw arm rather than repositioning the workpiece, the main advantage is the integrated cooling system as standard. This makes the EBS 128 CL a great choice for the semi-professional craftsman – performance, ergonomics and easy operation. Capabilities: - Mitre cuts in the range (+45° to -60°) - Infinitely variable saw arm adjustment thanks to hydraulic cylinder - Automatic cut-off – limit switch Fpedpsyr Nq Uofx Ac Dsf - Sturdy, torsion-resistant saw arm - 3 cutting speeds adjustable via V-belt - Robust frame guarantees precise and quiet operation without vibration - Standard quick-release vice and workpiece stop - Integrated cooling system as standard - Equipped according to the latest CE standards with a separate emergency stop button Technical specifications: Cutting capacity round 90°: 125 mm Cutting capacity flat 90°: 100 x 150 mm Cutting capacity round 45° R: 95 mm Cutting capacity flat 45° R: 95 x 76 mm Cutting capacity round 60°: 50 mm Cutting capacity flat 60°: 50 x 56 mm Working height: 740 mm Band saw blade dimensions: 1638 x 13 x 0.65 mm Band saw blade width: 13 mm Cutting speeds: 23 / 35 / 55 m/min Motor power: 0.75 kW Motor power S1 100%: 0.55 kW Voltage: 400 V Dimensions (W x D x H): 980 x 550 x 1100 mm Weight approx.: 85 kg Scope of delivery: - Band saw - Quick-release vice - Workpiece stop - Automatic cut-off limit switch - Mobile machine base - Hydraulic cylinder - Cooling system - Separate CE-compliant emergency stop button

Būklė: naujas, Cutting capacity at 90 degrees: round 105 mm Cutting capacity at 90 degrees: square 100 mm Cutting capacity at 90 degrees: rectangular 100 x 105 mm Saw blade dimensions: 1335 x 13 x 0.65 mm Dimensions (L x W x H): 650 x 310 x 300 mm Blade speed: 30 - 80 m/min Total power requirement: 0.95 kW Machine weight: approx. 18 kg Special Offer Price!! Berg & Schmid - Portable Band Saw PBS 90 ESC Powerful and particularly robust metal band saw with aluminum die-cast saw table and infinitely variable cutting speed for Fpsdpfxjfv Aq Rs Ac Dsf mitre cuts up to 60° Shipping contribution: €25 Images are of the identical PBS 110 model.

Būklė: naujas, Cutting diameter: 225 mm Saw band length: 2480 mm Cutting width: 250 mm Cutting speed: 45 / 90 m/min Saw band dimensions: 2480 x 27 x 0.9 mm Cutting capacity at 45°: flat 135 x 185 - 145 x 150 mm Cutting capacity at 45°: round 150 mm Fodpfx Acolb I Daj Dopf Cutting capacity at 45°: square 145 mm Cutting capacity at 60°: flat 63 x 107 - 69 x 90 mm Cutting capacity at 60°: round 70 mm Cutting capacity at 60°: square 70 mm Cutting capacity at 90°: flat 240 x 160 - 250 x 110 mm Cutting capacity at 90°: round 225 mm Cutting capacity at 90°: square 185 mm Total power requirement: 0.75 / 1.1 kW Machine weight approx. 200 kg Space requirement approx. 1385 x 580 x 890 mm Technical Features: - Hydraulic system for controlled downfeed of the saw head - Automatic cut-off at end of cut - Powerful three-phase induction motor with 2 speeds and oil-bath gearbox - Saw bow, vise, and swivel components made of cast steel - Steel band guides with ball bearings - Quick-release vise - Front lever for locking the mitre adjustment - Coolant pump with aluminium housing - Large handwheel for easy blade tensioning - Pressure gauge to display band tension (600–1000 kg/cm³) - Emergency stop safety switch - Chip brush for cleaning the saw band STANDARD EQUIPMENT: - Mountable base cabinet - Coolant tank - Electric coolant pump - Length stop for serial cuts - Tools for blade change and adjustments - Chip removal brush - Hydraulic cylinder with feed control

Būklė: naujas, Cutting diameter: 220 mm Saw blade length: 2455 mm Table height: 850 mm Cutting width: 230 mm Cutting speed: 35 + 70 m/min Saw band dimensions: 2455 x 27 x 0.9 mm Cutting capacity at 60° round: 90 mm Cutting capacity at 60° square: 90 mm Cutting capacity at 60° flat: 90 x 100 mm Cutting capacity at 45° round: 150 mm Cutting capacity at 45° square: 150 mm Cutting capacity at 45° rectangular: 150 x 210 mm Cutting capacity at 90° round: 220 mm Cutting capacity at 90° square: 210 mm Cutting capacity at 90° rectangular: 230 x 185 mm Total power requirement: 1.2 kW Machine weight approx. 0.24 t Space required approx. 1.2 x 0.6 x 1.7 m SPECIAL OFFER PRICE!!! -Mitre cuts up to 60° left -Cutting speed 35 / 70 m/min -Quick-release vise Fodpfx Acsd Iip Us Djpf -Carbide saw band guides -Band tension control -Electric cooling system (automatic) Auto-Cut System = 3-stage system -Automatic saw frame lowering by hydraulic cylinder -Continuously adjustable feed -With limit switch -Rapid lowering of the saw frame from rest position to the workpiece, then switch to normal saw feed -Manual operation Shipping charge share: €85

Būklė: naujas, Gamybos metai: 2026, Band saw for metal cutting with optimal cutting range, widely used in locksmith workshops, production facilities, and by craftsmen. Machine Characteristics The CORMAK BS 128HDRC metal band saw offers an optimal cutting range and is designed for professional craftsmen, distinguished by its efficiency and ease of use. It features a swivel arm adjustable to both sides, which is a significant advantage when cutting materials at an angle. Despite its compact dimensions and relatively high weight (109 kg), the machine is very stable and does not vibrate when cutting larger materials—unlike lighter machines. The workpiece can be fed manually or with any type of feeding device. Feed during cutting is gravity-driven, based on oil flow in a dual-chamber hydraulic cylinder. The appropriate descent speed of the arm is achieved via a valve regulating the oil flow between the cylinder chambers. The straightness of the cut is ensured by a set of blade guide bearings. Standard equipment includes an automatic limit switch and ON/OFF switch according to IP54 standards. The saw frame swivels for double miter cuts in the range from -45° to +60°. Technical specifications BLADE LENGTH: 1640 x 13 x 0.65 mm BLADE TENSION: mechanical (manual) CUTTING SPEED: 20 / 29 / 50 m/min POWER SUPPLY: 230V ARM DESCENT CONTROL: stepless, via hydraulic cylinder CUTTING RANGE: -45° to +60° DIMENSIONS: 1000 x 550 x 1100 mm WEIGHT: 103 kg Max. cutting range [mm]: Angle 0º Ø125 Fpsdpfx Ajudim Dsc Def 150 x 100 120 x 120 45º Ø90 90 x 90 90 x 90 60º Ø55 55 x 55 55 x 55 -45º (left) Ø75 75 x 75 75 x 75 Scope of delivery - Band saw with bimetal blade - 3rd generation hydraulic cylinder - Table for vertical cuts - Quick-release vise - Coolant system - Workpiece stop/limiter - Automatic limit switches - Modern thermal motor protection - Mobile base with 4 wheels - Technical documentation in Polish (DTR) Additionally included: - 2 M42 saw blades - 5L Emulgol coolant - ZW580 magnetic chip collector

Būklė: naujas, Gamybos metai: 2026, Piła taśmowa do metalu o optymalnym zakresie cięcia, powszechnie stosowana w zakładach stolarskich, produkcyjnych i rzemieślniczych. Opis maszyny Piła taśmowa do metalu CORMAK BS 128HDRC z optymalnym zakresem cięcia, przeznaczona dla profesjonalistów, wyróżnia się wysoką wydajnością i łatwością obsługi. Dużą zaletą w cięciu pod kątem jest możliwość obracania ramienia w obie strony. Pomimo niewielkich gabarytów duża masa własna (103 kg) zapewnia stabilność i brak wibracji podczas cięcia większych materiałów. Cięty element może być podawany ręcznie lub za pomocą podajników. Opuszczanie ramienia podczas cięcia odbywa się grawitacyjnie, z przepływem oleju w dwukomorowym cylindrze hydraulicznym. Regulacja opuszczania ramienia realizowana jest poprzez zawór sterujący przepływem oleju między komorami cylindra. Dokładne cięcie zapewnia zestaw łożysk prowadzących taśmę tnącą. Maszyny wyposażone są w wyłącznik krańcowy oraz włącznik/wyłącznik zgodny z normą IP54. Obracana rama piły umożliwia dwustronne ukosowanie w zakresie -45° do +60°. Dane techniczne Wymiary taśmy tnącej: 1640×13×0,65 mm Prędkość cięcia: 23/34/54 m/min Moc: 0,55 kW/230V Regulacja opuszczania ramienia: bezstopniowa, za pomocą cylindra hydraulicznego Zakres cięcia: -45° do +60° Wymiary: 942×442×548 mm Waga: 103 kg Maksymalny zakres cięcia [mm] Kąt 0°.....ø125 mm.....100×150 mm....100×100 mm -45°.....ø90 mm.....90×75 mm.....90×90 mm +45°.....ø90 mm.....90×75 mm.....90×90 mm +60°.....ø55 mm.....55×55 mm.....55×55 mm Wyposażenie standardowe: Trzeciej generacji cylinder hydrauliczny Fpedpfxsmrp Tls Ac Dsf Stół do cięcia w pionie Szybkomocujący imadło Układ chłodzenia y ogranicznik oporowy detalu Automatyczne wyłączniki krańcowe Nowoczesne zabezpieczenie termiczne silnika Mobilna podstawa na czterech kołach Instrukcja obsługi Podana cena jest ceną netto. Cena nie zawiera kosztów wysyłki. W celu uzyskania dalszych informacji prosimy o kontakt telefoniczny lub mailowy. Zapraszamy do zapoznania się z ofertą na naszej stronie internetowej.

Būklė: naujas, Gamybos metai: 2026, Funkcionalumas: visiškai funkcionalus, Bandsäge für Metall mit optimalem Schnittbereich, häufig eingesetzt in Tischlereien, Produktions- und Handwerksbetrieben. Maschinenbeschreibung Die CORMAK BS 128HDRC Bandsäge für Metall bietet einen optimalen Schnittbereich und ist speziell für professionelle Anwender konzipiert. Sie zeichnet sich durch Effizienz und eine besonders einfache Handhabung aus. Das beidseitige Schwenken des Sägebügels ist ein großer Vorteil beim Gehrungsschneiden. Trotz kompakter Abmessungen sorgt das hohe Eigengewicht (103 kg) für einen sehr stabilen und vibrationsfreien Betrieb auch beim Schneiden größerer Werkstücke. Das Material kann sowohl manuell als auch automatisch zugeführt werden. Der Sägevorschub erfolgt gravitationsbasiert über einen zwei-Kammer-Hydraulikzylinder mit Ölstrom. Die Steuerung des Sägebügel-Absenkens wird durch ein Ventil geregelt, das den Ölfluss zwischen den Zylindern kontrolliert. Ein gerader Schnitt wird durch ein Lagersystem zur Bandführung gewährleistet. Die Maschinen sind standardmäßig mit einem Endschalter sowie einem nach IP54 zertifizierten EIN/AUS-Schalter ausgestattet. Der schwenkbare Sägebügel ermöglicht das doppelseitige Gehrungsschneiden im Bereich von -45° bis +60°. Technische Daten Sägebandabmessung: 1640×13×0,65 mm Schnittgeschwindigkeit: 23/34/54 m/min Antriebsleistung: 0,55 kW / 400 V Absenkregelung: stufenlos, hydraulisch Gehrungsbereich: -45° bis +60° Abmessungen (L×B×H): 942×442×548 mm Gewicht: 103 kg Maximaler Schnittbereich [mm] Winkel 0° ….. ø125 mm ….. 100×150 mm …. 100×100 mm -45° ….. ø90 mm ….. 90×75 mm ….. 90×90 mm +45° ….. ø90 mm ….. 90×75 mm ….. 90×90 mm +60° ….. ø55 mm ….. 55×55 mm ….. 55×55 mm Serienausstattung - Hydraulikzylinder der 3. Generation - Tisch für Vertikalschnitte - Schnellspann-Schraubstock - Kühlmittelsystem - Werkstückanschlag - Automatische Endabschalter Fjdpfx Acewq A Dys Dspf - Moderner Motorthermoschutz - Fahrgestell mit vier Lenkrollen - Bedienungsanleitung Der Preis versteht sich netto. Versandkosten sind nicht im Preis enthalten. Für weitere Informationen stehen wir Ihnen telefonisch oder per E-Mail zur Verfügung. Besuchen Sie auch unser Online-Angebot auf unserer Webseite.

Būklė: naujas, Gamybos metai: 2026, CORMAK HBS260 band saw for cutting pipes, profiles, and bars is widely used in all metalworking shops where precision, quality, and cutting speed are essential. The model features a swiveling arm adjustable from 0-60°. The design of the saw bow ensures accurate and quiet operation. It comes with a removable chip tray for easy cleaning! Machine Features This horizontal metal band saw with a swiveling arm allows for cutting perpendicular or at any angle between 0 and 60° to the material axis. The workpiece can be fed manually or with any mechanical device, while the saw blade feed operates automatically. The blade guides are fitted with special carbide inserts and bearings, which greatly improve blade tracking, longevity, straightness, and the quality of the cut. Carbide blade guides significantly reduce wear on both the machine and the blade. The machine is equipped with a high-performance coolant pump with a closed-cycle cooling system. The saw’s arm is cast from a single piece of cast iron, and, combined with a 27 mm wide band saw blade, it is fully suitable for serial cutting of both profiles and solid materials. The vice is mounted on an adjustable bed with a quick-release clamp. Blade guides are equipped with carbide inserts and rolling bearing systems. It is the CARBIDE BLADE GUIDES that ensure cutting precision and straightness. The upper part of the base is shaped to form a tray for collecting coolant and chips generated during the cutting process. To the base, a sturdy cast iron work table with a swiveling arm is mounted, along with a control panel on a separate arm. During cutting, the main cutting motion is performed by the moving saw blade, while arm feed is via gravity. The speed of arm descent (cutting speed) is adjusted using a hydraulic cylinder. Feed rate is controlled from the saw’s control panel. There are two blade speeds to choose from: 35 and 70 m/min. In the lower end position of the arm (after cutting the material), the drive to the blade is automatically switched off. Safety is ensured by saw blade guards and microswitches that stop the motor after the cutting cycle or when any guard is opened. Additional protection consists of the automatic saw shut-off in the event of blade breakage. Band saw blade size [mm]: 2520 x 27 x 0.9 Blade tension: mechanical (manual) Blade speeds [m/min]: 35, 70 Arm descent adjustment: stepless – hydraulic cylinder Vice base height [mm]: 860 Saw wheel diameter [mm]: 300 Saw frame swivel [°]: 0-60 Power supply: 3-phase 400V Main motor power [kW]: 1.1/1.5 Coolant pump motor power [kW]: 0.05 Dimensions with base [cm]: 150x80x140 Weight [kg]: gross/net - 210 / 180 kg Fjdoudi Uzepfx Ac Djpf Additionally: - 2 pcs M42 saw blades - 5L Emulgol coolant - Magnetic chip collector ZW580

Būklė: naujas, Gamybos metai: 2026, Manual band saw for cuts from 0° to 60° to the right. Hydraulic blade tension, bow handle with control button. Fpjdpfx Ajgculvec Def Combination blade guide with lateral bearings. Carbide cutting inserts and an upper bearing. Manual cutting possible, or cutting without an operator using the weight of the bow, controlled by hydraulic brakes; afterwards, the bow is manually lifted back to the desired position. Manual clamp for quick and precise securing of the workpiece. Bow rotation from 0° to 60° to the right with locking positions, precise angle measurement, manual vise with quick-release lever. Millimeter-graded scale rod. Coolant tank integrated on the upper side of the base frame with a drain nozzle and an electric coolant pump for cooling both sides of the saw blade guides. Control voltage: 24 VAC, main switch and control panel. Maximum current protection and short-circuit protection. Connection voltage: 400V/50Hz/3Ph standard. Machine color: yellow RAL 1018 and grey RAL 7036. You are welcome to inspect the desired machine at any time in our production/showroom. Please feel free to contact us. We look forward to hearing from you! Plantec Maschinen GmbH

Būklė: naujas, Gamybos metai: 2026, Stacionari kampinė juostinė pjovimo staklė universaliojo panaudojimo rūšis Savybės: Fodpfx Ajg Hy Shoc Dspf - Tvirtas pjovimo rėmas iš aliuminio liejinio - Pjovimo rėmas pasukamas virš medžiagos - Tvirtas spaustuvas - Didelė pjovimo zona - Dvi pjovimo greičio pasirinktys - Karbido su rutuliniais guoliais juostos kreipiančiosios - Elektrinė aušinimo skysčio sistema Techniniai duomenys: - Kampai nuo 0° iki 60° į dešinę - Variklio galia 2000 W/1-fazinis, 230 V - Juostos greitis laipsniškai reguliuojamas nuo 35 iki 80 m/min. - Staklių svoris 140 kg - Juostos matmenys: 2140 x 20 x 0,9 mm Pjovimo sritys: 0° = Ø 175 arba 200 x 75 / 190 x 135 / 175 x175 mm 45°= Ø 110 / 150 x110 / 110 x 110 mm 60°= Ø 75 / 100 x 70 / 75 x 75 mm

Būklė: naujas, Cutting capacity at 90° (round): 130 mm Cutting capacity at 90° (square): 130 mm Cutting capacity at 90° (rectangular): 130 x 125 mm Saw blade dimensions: 1440 x 13 x 0.65 mm Dimensions (L x W x H): 350 x 690 x 520 mm Blade speed: 30 - 80 m/min Total power requirement: 1.2 kW Machine weight: approx. 19 kg SPECIAL PRICE!! Berg & Schmid - Portable Band Saw PBS 130 ESC Fjdpfofv Aq Ujx Ac Dspf Powerful and particularly robust metal band saw with aluminum die-cast saw table and stepless cutting speed for mitre cuts up to 60°

Būklė: naujas, Cutting capacity at 90°: round 172 mm Cutting capacity at 90°: square 170 mm Cutting capacity at 90°: rectangular 170 x 170 mm Saw blade dimensions: 2035 x 20 x 0.9 mm Fpjdofgyhzepfx Ac Def Dimensions (L x W x H): 430 x 960 x 520 mm Blade speed: 30 - 80 m/min Total power requirement: 1.5 kW Machine weight: approx. 38 kg SPECIAL OFFER PRICE!! Berg & Schmid - Mobile Bandsaw PBS 171 ESC Powerful and particularly robust metal bandsaw with die-cast aluminium saw table and steplessly adjustable cutting speed for mitre cuts up to 60° Optional: Machine base Type 20508

Būklė: naudotas, Gamybos metai: 2025, mašinos/transporto priemonės numeris: 4123479, Funkcionalumas: visiškai funkcionalus, galia: 1,13 kW (1,54 AG), įvesties srovės tipas: trifazis, bendras aukštis: 27 mm, bendras svoris: 225 kg, Apvalaus plieno pjovimo diapazonas ties 45°: 150 mm, Apvalaus plieno pjovimo diapazonas ties 90°: 220 mm, Kvadratinio plieno pjovimo diapazonas 45° kampu: 150 mm, Kvadratinio plieno pjovimo diapazonas prie 90°: 210 mm, juostinio pjūklo ilgas: 2 450 mm, pjūklo juostos plotis: 9 mm, reikalingas aukštis: 1 740 mm, vietos reikalavimas ilgis: 1 550 mm, reikalingas plotis: 870 mm, darbinio aukščio: 915 mm, Hidraulinis cilindras / Emulsijos siurblys / Ekscentrinis įtempėjas / Rėmas / Pjūklo juosta / 400V kištukas -16A- Pjovimo greitis: 35 + 70 m/min. Fpjdpfxjxxi N Aj Ac Def

Būklė: naujas, Pjovimo skersmuo 235 mm Pjūklo juostos matmenys 2645 x 27 x 0,9 mm Pjovimo plotis 280 x 190 mm Pjovimo greitis 45/90 m/min Pjovimo našumas 60° - apvalus 120 mm Pjovimo našumas 60° - kvadratas 120 mm Pjovimo našumas 45° - apvalus 190 mm Pjovimo našumas 45° - kvadratas 170 mm Prijungimo įtampa 400 V Bendras galios poreikis 1,1 kW Mašinos svoris apie 290 kg Matmenys I x P x A 1,2 x 0,8 x 1,2 m Fjdsynnklspfx Ac Dopf Dvigubo kampo juostinis pjūklas -Kampiniai pjūviai iki 60° kairėje ir 45° dešinėje -Spaustukas su greito užveržimo įtaisu -Juostos įtempimo kontrolė -Elektrinis aušinimo automatas

Būklė: naujas, Pjovimo skersmuo 255 mm Fpodpfx Acsynni Us Djf Juostinio pjūklo matmenys 2750 x 27 x 0,9 mm Pjūvio plotis 200 x 320 mm Pjovimo greitis 20–80 m/min Pjovimo galia ties 60° apvalus: 125 mm Pjovimo galia ties 60° kvadratinis: 125 x 125 mm Pjovimo galia ties 45° apvalus: 195 mm Pjovimo galia ties 45° kvadratinis: 350 mm Maitinimo įtampa 400 Voltų Bendras galios poreikis 1,5 kW Mašinos svoris apie 290 kg Matmenys (I x P x A) 1,1 x 0,8 x 1,75 m Dvipusio kampo juostinis pjūklas – Kampiniai pjūviai iki 60° į kairę ir 45° į dešinę – Greito fiksavimo spaustuvas – Juostos įtempimo kontrolė – Elektrinė automatinė aušinimo sistema

Būklė: geras (naudotas), Gamybos metai: 2010, Cutting diameter: 220 mm Saw band length: 2480 mm Table height: approx. 910 mm Cutting capacity at 90°: flat 245 x 115 mm Cutting capacity at 90°: square 195 x 195 mm Cutting capacity at 45°: round 150 mm Cutting capacity at 45°: square 140 x 140 mm Cutting capacity at 60°: round 85.0 mm Cutting capacity at 60°: square 85 x 85 mm Speed range: 45 + 90 m/min Saw blade dimensions: 2480 x 27 x 0.9 mm Maximum clamping width: 270 mm Total power requirement: 0.75 + 1.1 kW Machine weight: approx. 200 kg Space requirement: approx. 1430 x 720 x 1700 mm Original price in 2010: €2,400 Special price on request Equipment: Fjdpfx Acjyf N D Uj Djpf - For cutting profiles, pipes, and solid materials made of iron and non-ferrous metals - Saw bow can be swiveled up to 60° for miter cuts - Infinitely adjustable lowering via hydraulic lowering cylinder - Torsion-free, heavy-duty saw arm made of cast iron - Two saw band speeds for optimal cutting results (400 V) - Automatic shut-off after material is cut through - Sturdy cast iron vise with quick-release - Ball-bearing saw band guide with quick adjustment for adapting to workpiece width ensures optimal working results - Original operating manual

Būklė: naudotas, Funkcionalumas: visiškai funkcionalus, galia: 0,48 kW (0,65 AG), įėjimo įtampa: 380 V, įėjimo srovė: 2 A, Įranga: sūkių greitis be galo kintamas, Siūlome šią naudotą Hubert+Moser KG 80KF3 juostinę pjūklą, pagaminimo metai nežinomi. Fpedjymflqopfx Ac Dsf Jei turite klausimų arba reikia daugiau informacijos, prašome parašyti mums žinutę arba paskambinti.

Būklė: naujas, Cutting diameter: 410 mm Saw band length: 5800 x 41 x 1.3 mm Table height: 750 mm Cutting range at 90°: flat 700 x 410 mm Cutting range at 45°: round 410 mm Cutting range at 45°: flat 500 x 410 mm Cutting range at 45°: round left 410 mm Cutting range at 45°: flat left 430 x 410 mm Cutting range at 30°: round 320 mm Fedsx Sr Dropfx Ac Dopf Cutting range at 30°: flat 320 x 410 mm Cutting speed: 15 - 150 m/min Workpiece weight max.: 250 kg/m Total installed power: 5.5 kW Machine weight approx.: 3200 kg Space requirement approx.: 4500 x 2800 x 2000 mm - Ergonomic control panel, network-capable, offering various option packages * Teleservice for remote maintenance * Sawing program setup in work preparation * Import of sawing programs from CAD via DSTV interface and data export - Automatic material feed: - Compact design for shorter cuts or with flexible feed clamp available in almost all lengths - Precise positioning of the material by servo positioning technology - Advanced electric saw feed with ball screw spindle: - Maximum cutting performance and quality, gentle on the saw blade - Consistent use of state-of-the-art linear guides: - Smooth running, high load capacity, low maintenance, and zero backlash - Unique and patented double mitre system: - Material is always clamped at a right angle Equipment: - Automatic cutting pressure and feed monitoring - Frequency-controlled AC drive 15-150 m/min, 5.5 kW - Hydraulic full stroke material clamping - Automatic vise traverse - Automatic saw frame height adjustment - Minimum speed and saw blade monitoring - Electric mitre adjustment via servomotor - Visualized program input with CNC control - Integrated MEBA clamping feed system from 5-2300 mm per stroke with integrated roller conveyor *Optional equipment: - Laser for cutting line indication / marking cuts - Powered chip brush - Micro dosing system - Clamping pressure regulation - Material bundle clamping - Job menu - Material database - Zero-point stop - Scraper belt conveyor for optimal chip disposal, 2000 mm length - Cut path monitoring

Būklė: naujas, Cutting Range: - Round 0°: 170 mm - Square 0°: 150 x 150 mm - Flat 0°: 150 x 190 mm Fpedpfxeilk H Tj Ac Dof - Round 45°: 125 mm - Square 45°: 95 x 120 mm Working height: 870 mm Cutting speeds: 40 / 80 m/min Saw blade: 2080 x 20 x 0.9 mm Coolant pump: 100 W Saw motor: 0.75 kW Connection: 400 V Dimensions (L x W x H, approx.): 1340 x 810 x 1320 mm Weight, approx.: 146 kg Features: - Saw bow swivels up to 45° - Equipped with two blade speeds for optimal adjustment to the workpiece - Ideal for cutting pipes, profiles, and solid materials made of stainless steel, iron, etc. - Generously sized saw arm for low-vibration operation - Hydraulic lowering of the saw arm via hydraulic cylinder - Low-noise operation thanks to robust design - Automatic shut-off at end of cut via micro limit switch - Quick-release vice for easy and fast clamping of workpieces - Precise, adjustable blade guides for optimal cutting results - Coolant system with pump - Includes base frame - CE/IEC compliant, German documentation and German service Scope of Delivery: - Bi-metal saw blade 2080 x 20 x 0.9 mm, 6/10 TPI - Blade tension adjustable via pressure gauge - Quick-release vice - Material stop - Coolant system with pump - Hydraulic lowering cylinder - Motor protection switch - Automatic cut-off at end of cut - Base frame

Būklė: naujas, Cutting range round 0°: 127 mm Cutting range flat 0°: 125 x 130 mm Cutting range round 45° right: 90 mm Cutting range square 45° right: 90 x 90 mm Cutting range round 60° right: 45 mm Cutting range square 60° right: 45 x 45 mm Vice opening: 130 mm Saw blade dimensions: 1440 x 13 x 0.65 mm Cutting speed: 60 m / min Motor power: 0.55 kW Voltage: 230 V Approx. weight: 25 kg Features: - Saw bow swivels up to 60° - Ideal for cutting pipes, profiles, and solid materials made of stainless steel, iron, etc. - Sturdy saw arm ensures low-vibration operation Fpjdpfx Aoilk Ekjc Dof - Low-noise thanks to solid construction - Automatic shut-off after cutting via micro switch - Quick-action vice for easy and fast workpiece clamping - Precision-adjustable blade guide for optimal cutting results - Environmentally friendly, as no lubricants or coolant are required - Ideal for onsite use due to low weight - Optional base available (not included in scope of delivery) Equipment: - Saw blade 1440 x 13 x 0.65 mm - Material stop - Ergonomic handle Base frame available at extra cost: 129 euros net (special price)

Būklė: naujas, Machine in stock and immediately available Horizontal Mitre Band Saw S 225 G Cutting range 90°, round: 225 mm Cutting range 90°, square: 200 x 200 mm Cutting range 45°, round: 160 mm Cutting range 45°, square: 160 x 160 mm Cutting range 60°, round: 100 mm Cutting range 60°, square: 100 x 100 mm Saw blade: 2480 x 27 x 0.9 mm Cutting speeds: 45 / 90 m/min Motor power: 1.5 kW Voltage: 400 V Features: - Saw bow can be swiveled up to 60° - Two saw band speeds for optimal adaptation to the workpiece - Ideal for machining pipes, profiles, as well as solid material made of stainless steel, iron, etc. - Generously dimensioned saw arm for low-vibration operation - Lowering of the saw arm via hydraulic lowering cylinder - Quiet operation due to robust construction - Automatic shut-off after cutting is complete via micro limit switch - Quick-release vise for easy and fast clamping of the workpiece - Precise, adjustable saw blade guide for optimal cutting results - Coolant device with pump - Including base frame - CE/IEC, German documentation and German service Scope of delivery - Bi-metal saw blade 2480 x 27 x 0.9 mm, 6/10 TPI - Carbide guides (4 jaws) - Adjustable workpiece stop 0.5 m - Pressure gauge for blade tension - Quick-release vise - Integrated coolant system - Hydraulic bow lowering Fpedpfjd R Sklox Ac Dof - Motor protection switch - Automatic end shut-off - Base frame

Būklė: naujas, Cutting diameter: 350 mm Saw band length: 4640 x 34 x 1.1 mm Table height: -- mm Cutting diameter: 350 mm Cutting speed: 15 - 100 m/min Total power requirement: 4.0 kW Machine weight approx.: 2800 kg Space requirement approx.: 2200 x 3200 x 2200 mm Fully automatic bandsaw with dual-column guidance system for series cutting, especially in hard-to-machine materials and solid stock. With this machine, MEP offers you a technologically advanced system built from first-class materials, resulting in an exceptionally robust and torsion-resistant structure. The extremely solid saw frame made of cast iron ensures the necessary stability for impressive cutting results, while the powerful cast iron columns, along which the saw frame glides on pre-tensioned linear guides, guarantee the highest cutting precision, even under maximum load. The modern machine control unit (MEP NC 5.0) offers maximum user convenience and ensures trouble-free operation (monitoring/evaluation/correction in real-time). MAXIMUM PERFORMANCE > The two operating modes (semi-automatic and automatic) enable efficient cutting under any conditions. > The control system allows storage of up to 100 cutting programs, each with different quantities and lengths, minimizing programming time for frequently repeated jobs. > The automatically detected start position of the saw head reduces setup time. > The saw head feed, via linear guides driven by hydraulic cylinders with pre-tensioned ball bushings, reduces mechanical vibrations during cutting and provides increased stability. > The automatic alignment of the front saw blade guide head, based on the dimensions of the bars to be cut, reduces processing time. > Saw blade tension is effected by the brushless motor and constantly monitored and automatically maintained at the set minimum value. EXTREMELY FLEXIBLE > The feed system with 600 mm stroke is repeatable and can cut any length. > The vertical roller pair holds and aligns any type of bar or bundle being fed. > The vector inverter enables stepless adjustment of the blade speed from 15 to 100 m/min, allowing cuts on any material. > The motorized chip conveyor can be mounted on either the right or left of the cutting area. FEATURES: Fully automatic control - NC 5.0 -Innovative (Windows CE-based) touch-screen control with additional soft-touch keys for frequent operating functions -USB port Fedpfx Aelf Tu Usc Djpf -Joystick for manual axis (X-Y) control -Controlled blade descent with automatic compensation via a servo valve mounted in the cylinder, continuous monitoring of preset torque, and precise feed adjustment in mm/min -Adjustment/preselection of continuously variable band speed (m/min) -Saw band tension with band tension monitoring and display on-screen via electronic transducer -Automatic detection of cut start -Large 7" color touchscreen for display and selection of all machine functions and parameter settings, enabling programming within seconds. Detailed display of alarm and error messages -Numerous...