Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2002, veikimo valandos: 44 590 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 200 t, pildymo angos plotis: 1 020 mm, pildymo angos ilgis: 2 000 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 1 100 mm, alyvos bako talpa: 3 100 l, galia: 150 kW (203,94 AG), paskutinio kapitalinio remonto metai: 2025, Technical Data - Baler: Manufacturer: MACPRESSE EUROPA S.R.L. Type: 112 Year of manufacture: 2002, partially overhauled in December 2025 Operating hours: 44,590 hours as of December 2025 Main press force: 200 t Specific pressing force: 16.5 kg/cm² Hodpex Dnb Ujfx Ab Sjni Feed chute dimensions: 2,000 x 1,020 mm Filling volume: 2.65 m³ Theoretical throughput: 795 m³/hour Bale dimensions: 1,100 x 1,100 mm, length adjustable Drive power: 2 x 75 kW Binding: 5-fold horizontal, fully automatic Throughput for MSW: approx. 48 to 54 t/hour, depending on material Hydraulic oil tank capacity: 3,100 L Machine weight, press: approx. 50.8 t Scope of delivery: 1 unit baler MACPRESSE, type 111A 1 unit operating manual with CE declaration, electrical and hydraulic schematic Remarks: The machine has been serviced and partially overhauled in our workshop. The following work was performed and parts replaced: • Hydraulic oil tank completely drained and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Dismantling of the press ram, complete disassembly, overhaul of the mechanics • Replacement of the front two main guide rollers • Replacement of the knives on the press ram • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, all seals replaced • Replacement of the counter knife in the frame • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame renewed on left and right sides • Worn press floor cut out, bottom plate replaced with wear-resistant HARDOX steel • Dismantling of the tying and twisting unit, complete disassembly, overhaul of the mechanics, replacement of all twister shafts and ball bearings • Replacement of all wire rollers in the needle heads • Wire cutters cleaned and reset, chains lubricated and tensioned • All wire deflection pulleys made operational • All door contact switches replaced • Vibulator dismantled, disassembled and serviced • General maintenance performed Finally, the baler was subjected to a machine test in both manual and automatic modes—see our video for a functional test of the machine. The documentation (operator manual, CE, electrical/hydraulic schematic) is complete. Viewing by appointment is possible. No liability is assumed for the technical specifications or possible errors.

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 2011, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 112010, spaudimo jėga: 60 t, pildymo angos plotis: 550 mm, pildymo angos ilgis: 1 160 mm, kamuolio ilgis: 1 200 mm, ryšulio plotis: 800 mm, ryšulio aukštis: 1 100 mm, balo svoris: 420 kg, bendras plotis: 1 400 mm, bendras aukštis: 2 170 mm, bendras ilgis: 1 890 mm, įvesties srovės tipas: trifazis, įėjimo įtampa: 400 V, bendras svoris: 2 430 kg, galia: 7,5 kW (10,20 AG), paskutinio kapitalinio remonto metai: 2025, Brand: Dixi The stated price is net, plus statutory VAT, ex works, and without packaging. The press has been cleaned and function-tested. Technical Specifications: - Manufacturer: Dixi - Model: 60S - Bale size (LxWxH): 1200 x 800 x 1100 mm - Bale weight: 340–500 kg - External dimensions (LxWxH): 1890 x 1400 x 2170 mm - Feed opening: 1160 x 550 mm - Pressing force: 600 kN - Output capacity: 1–2 bales per hour - Number of wire channels: 4 - Press weight: 2,430 kg - Power supply: 400 V / 50 Hz - Power consumption: 7.5 kW - Installation location: indoor / outdoor under cover - Serial number: 112010 - Year of manufacture: 2011 Please refer to the original documentation, which can be obtained directly from the manufacturer. Hedpfx Aswnpyveb Ssni

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 2012, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 113889, spaudimo jėga: 60 t, pildymo angos plotis: 550 mm, pildymo angos ilgis: 1 160 mm, kamuolio ilgis: 1 200 mm, ryšulio plotis: 800 mm, ryšulio aukštis: 1 100 mm, balo svoris: 420 kg, bendras plotis: 1 400 mm, bendras aukštis: 2 170 mm, bendras ilgis: 1 890 mm, įvesties srovės tipas: trifazis, įėjimo įtampa: 400 V, bendras svoris: 2 430 kg, galia: 7,5 kW (10,20 AG), paskutinio kapitalinio remonto metai: 2025, Brand: Dixi The stated price is subject to statutory VAT, ex works, and excludes packaging. Hodpfx Abjwnpx Es Sjni The baler has been cleaned and function-tested. Technical details: Manufacturer: Dixi Model: 60S Bale size (LxWxH): 1200 x 800 x 1100 mm Bale weight: 340-500 kg External dimensions (LxWxH): 1890 x 1400 x 2170 mm Feed opening: 1160 x 550 mm Pressing force: 600 kN Throughput: 1 - 2 bales/h Number of wire ties: 4 Machine weight: 2,430 kg Power supply: 400 V / 50 Hz Power consumption: 7.5 kW Installation location: indoors / covered outdoors Serial number: 113889 Year of manufacture: 2012 Please refer to the respective original documentation, which can be obtained directly from the manufacturer.

Būklė: labai geros būklės (naudotas), Funkcionalumas: visiškai funkcionalus, pildymo angos plotis: 1 600 mm, pildymo angos ilgis: 2 200 mm, ryšulio plotis: 400 mm, ryšulio aukštis: 400 mm, bendras plotis: 3 345 mm, bendras aukštis: 3 160 mm, bendras ilgis: 7 440 mm, įėjimo įtampa: 380 V, bendras svoris: 28 000 kg, galia: 55 kW (74,78 AG), Įranga: dokumentacija / vadovas, Balių presas 400 x 400 mm. Labai gera būklė. Gerai prižiūrėta. Hsdpfsxcazwox Ab Seni

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2009, veikimo valandos: 22 029 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 80 t, pildymo angos plotis: 1 000 mm, pildymo angos ilgis: 1 400 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 600 kg, bendras svoris: 16 000 kg, galia: 45 kW (61,18 AG), paskutinio kapitalinio remonto metai: 2025, Technical Data Press: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: AVOS 1410-45/80 Year of manufacture: 2009 Operating hours: 22,029 hours (as of December 2025) Press force: 80 kN Specific pressing force: 103.9 N/cm² Feed chute dimensions: 1,400 x 1,000 mm Theoretical cycle time: 12 seconds Theoretical throughput: 300 m³/hour Bale dimensions: 1,100 x 750 mm (W x H), length is variable Drive power: 45 kW Total connected load: 75 kW Hnsdpfox A U Ncox Ab Sji Tying: 4-fold vertical, fully automatic Throughputs at a bulk density of: 30 kg/m³ approx. 6.0 t/hour 50 kg/m³ approx. 10.5 t/hour 100 kg/m³ approx. 17.5 t/hour Bale weights at a bale length of approx. 1.2 m: up to 600 kg, depending on material PLC controller: Siemens S7-300 Display panel: Pulsotronic Installed machine dimensions: 8,610 x 2,400 x 3,835 mm (L x W x H) Transport weight of press: 16 t Special Equipment: • Wear-resistant floor made of HARDOX steel • Special press ram for compacting 'difficult' materials and loose bulk materials of small particle size • Control cabinet air-conditioning • Machine feet height increase by 200 mm Comment: The machine was serviced and partially overhauled in our workshop. The following work was performed and parts replaced: • Disassembly of the press ram, breakdown into individual parts, overhauling the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right below the press ram o Plastic wear rails left/right above the press ram o Main plastic wear plate (support plate) centrally under the press ram • Steel guide rails left/right above in the frame renewed • Replacement of the entire base plate, four-part, made from wear-resistant HARDOX steel • Wire feed rails in the press floor newly welded and smoothed • Replacement of counter knife, two-part, in the frame • Adjustment of the knife gap to approx. 2.5 mm • Disassembly of the tie and twisting unit, breakdown into individual parts, overhauling the mechanics, replacement of all groove ball bearings and axial ball bearings of the twisting shafts, wire cutters cleaned and re-adjusted, chains lubricated and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses renewed • Oil and air filters renewed • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, was chemically analyzed, is still in good condition and therefore was not replaced; it can continue to be used • General maintenance carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for machine function test.

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2014, veikimo valandos: 5 612 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 48 t, pildymo angos plotis: 1 020 mm, pildymo angos ilgis: 1 250 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 550 kg, bendras aukštis: 2 800 mm, bendras svoris: 12 000 kg, transporto aukštis: 2 800 mm, alyvos bako talpa: 300 l, galia: 30 kW (40,79 AG), tūrio srautas: 332 m³/val, Technical Data – Baler: Manufacturer: HSM GmbH + Co. KG Model: VK 4812 Year of Manufacture: 2014 Operating Hours: 5,612 hours as of August 2025 Main Press Force: 48 t Specific Press Force: 58.2 N/cm² Feed Opening Dimensions: 1,250 x 1,020 mm Theoretical Cycle Time: 11.2 sec Theoretical Throughput: 332 m³/hour Bale Dimensions: 1,100 x 750 x 600 up to 1,200 mm Drive Power: 30 kW Total Connected Load: 32 kW Rated Current: 59 A Binding System: 4-fold horizontal, fully automatic Throughput rates by bulk density: - At 20 kg/m³: up to 6 t/hour, depending on material - At 50 kg/m³: up to 13 t/hour, depending on material Bale Weights: up to 550 kg, depending on material PLC Control: Siemens SIMATIC S7-200 Operator Panel: Siemens HMI Touch Panel Hydraulic Oil Tank Capacity: 300 L Oil Grade: HVI 46 Machine Installation Dimensions with Bale Slide: 10,046 x 4,387 x 2,705 mm (L x W x H) Transport Dimensions (Press): 8,500 x 2,500 x 2,750 mm (L x W x H) Machine Weight (Press): approx. 12 t Scope of Delivery: - HSM VK 4812 baler, without hydraulic oil, without conveyor equipment - Two wire spool boxes for 8 pieces of 40 kg wire spools, without wire - Bale slide - Machine documentation in German Remarks: The baler is equipped with an oil cooler and potential-free contacts for external control. Operation at the control cabinet is on the left in the pressing direction; the needle unit is on the right and can be folded back for transport. The baler has been partially overhauled and tested in our workshop, see photos and our function video. Documentation (operating manual, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Inspection by appointment. No liability is assumed for technical details or potential errors. Hnodpfevtpq Hox Ab Sei

Būklė: labai geros būklės (naudotas), Gamybos metai: 1990, veikimo valandos: 25 000 h, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 24.955, balo svoris: 600 kg, Įranga: dokumentacija / vadovas, Konti-275 B Baling Press – Performance, Reliability, and Efficiency in Material Compaction Discover the KONTI-275 B Baling Press, the ideal solution for efficient management of plastic, cardboard, and other recyclable waste. Engineered to deliver maximum performance, this industrial press is perfect for companies seeking to optimize storage space and reduce waste volume. Key Features: - Impressive pressing force with a capacity of up to 200 bar, ensuring effective compaction of materials in a short time. Hedsuqxpcjpfx Ab Seni - Variable bale weight ranging from 20 to 600 kg, depending on the type of material processed and pressure settings. - Advanced hydraulic system utilizing ISO VG 68 hydraulic oil, guaranteeing consistent and efficient operation even under intensive use. - Compact and robust design, optimized for industrial environments, with various feed options and customizable to meet workflow requirements. - Automation and safety: the press is fully automated, providing easy operation and maximum safety, thereby minimizing the risk of damage. Benefits: - Significant reduction in waste volume, saving both space and transport costs. - Fast and efficient operation thanks to full automation and continuous workflow. - Minimal maintenance required, with clear service recommendations to ensure a long equipment lifespan. - Versatility: suitable for a wide range of materials, from plastic and cardboard to other recyclable waste.

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 2004, spaudimo jėga: 200 t, galia: 0,045 kW (0,06 AG),

Būklė: labai geros būklės (naudotas), Gamybos metai: 2014, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 26 t, pildymo angos plotis: 1 500 mm, pildymo angos ilgis: 630 mm, kamuolio ilgis: 1 500 mm, ryšulio plotis: 800 mm, ryšulio aukštis: 1 140 mm, balo svoris: 500 kg, bendras plotis: 1 060 mm, bendras aukštis: 2 576 mm, bendras ilgis: 2 075 mm, bendras svoris: 1 220 kg, triukšmo lygis: 65 dB, galia: 4,6 kW (6,25 AG), Galinga presavimo mašina Orwak 3820 Power. Ypač tinkama didelių gabaritų kartonui ar plėvelei dėl itin didelės įkrovimo angos 1500 x 630 mm. Hnodpfexmvc Ejx Ab Ssi

Būklė: naudotas, Gamybos metai: 2022, veikimo valandos: 1 063 h, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 11973, Modelis / Tipas: RUF 11/2800/60 Mašinos Nr.: 11973 Gamybos metai: 2022 Pavaros variklis: 11 kW Našumas iki max.: 150 kg/val. (priklauso nuo medžiagos) Presavimo slėgis: 2800 kg/cm² Briketų formatas: ⌀60mm Darbo valandos: apie 1063 val. Garantija: 12 mėnesių po pristatymo Prieinamumas: apie 4–8 savaitės po avanso gavimo Detalės: + Siemens TP 700, Siemens S7-1200 Hodpjygrt Iefx Ab Soni + 600 x 1500mm bunkerį su prailginimu + Pneumatinis emulsijos siurblys

Gamybos metai: 2006, būklė: beveik kaip naujas (naudotas),

Būklė: geras (naudotas), Gamybos metai: 2009, Funkcionalumas: visiškai funkcionalus, Svoris 4950 kg, bendras svoris 12000 kg Hnsdpfx Aowpmckeb Sei Galia 5,5 kW

Būklė: naujas, Gamybos metai: 2025, Matmenys (ilgis/plotis/aukštis): 1800x1800x1900 mm Svoris: 3000 kg Bendras galios poreikis: 33,5 kW Hidraulinė briketų presas BP-500 - Maksimali našumas: 450 kg/val. - Variklis: 33 kW / 400 V, 50 Hz - Drožlių suspaudimas min.: 1000 kg/cm² - Maks.: 1700 kg/cm² - Medienos drėgnumas max.: 14 % - SIEMENS valdymas - Matmenys (I x P x A): 1800x1800x1900 mm - Svoris: 3000 kg Briketų matmenys: - Ilgis: 150 mm - Plotis: 60 mm - Aukštis: 40-105 mm Komplektacijoje: Hjdovz Ex Njpfx Ab Ssni - Pakavimo stotis su briketų padavimo konvejeriu - Pakavimo stalas su apverčiamu konteineriu - Plėvelės suvirinimo aparatas

Būklė: naujas, Gamybos metai: 2025, Matmenys (ilgis/plotis/aukštis): 1850x1500x1230 mm Svoris: 870 kg Bendras galios poreikis: 8 kW Briketavimo presas BP-120 PRO - Briketo diametras: 70 mm - Hidraulinis variklis: 7,5 kW - Našumas per valandą: 50/120 kg/h - Oro-aliejaus aušinimo sistema - 7 ciklai/min. - Maksimali briketo ilgis: 50 mm - Dvigubas manometras - Alyvos lygio jutiklis bake ir temperatūros jutiklis - Valdymo spinta su SIEMENS PLC ir lietimui jautriu ekranu - Darbo valandų skaitiklis - Sraigtinis kanalas, sraigtinis išleidimas - Medžiagos piltuvas: 1900 mm x 1600 mm - Įtampa: 400 V/50 Hz Hjdpfxevz Eqlj Ab Soni - Matmenys: L=1850, P=1500, A=1230 mm - Svoris: 870 kg

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2007, veikimo valandos: 13 209 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 50 t, pildymo angos plotis: 1 050 mm, pildymo angos ilgis: 1 250 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 700 mm, balo svoris: 500 kg, alyvos bako talpa: 400 l, paskutinio kapitalinio remonto metai: 2025, tūrio srautas: 108 m³/val, Technical data of the baler: Manufacturer (as per nameplate): BRAMIDAN (original manufacturer: Presto GmbH & Co. KG) Model: HC 50 (equivalent to Presto HPK 50) Year of manufacture: 2007 Hnedpfxew U Dt No Ab Soi Operating hours: 13,209 hours (as of March) Number of bales pressed: 23,379 pcs Pressing force: 50 t Specific pressing force: 650 kN/m² Feed opening dimensions: 1250 x 1050 mm (L x W) Filling volume: 0.96 m³ Theoretical cycle time: 32 seconds Theoretical throughput: 108 m³/hour Bale dimensions: 1100 x 700 mm (W x H), length variable Drive power: 15 kW Total current consumption: 50 A Binding: 4-fold vertical, fully automatic Throughput at a bulk density of: - 30 kg/m³: approx. 3.1 t/hour - 60 kg/m³: approx. 4.5 t/hour - 100 kg/m³: approx. 7.2 t/hour Bale weights at a bale length of approx. 1.2 m: up to 500 kg (depending on material) Hydraulic oil tank capacity: 400 L PLC: Siemens S7-200 Effective transport dimensions (excluding press): 6780 x 1800 x 2100 mm (L x W x H) Transport weight (press): 8.5 t Condition of the baler: The baler was in use at a production facility, exclusively for compacting cardboard, and has been regularly serviced. With only 13,209 operating hours, the machine has seen relatively low use. The baler has been partially overhauled and thoroughly tested in our workshop. The following overhaul work was carried out: - Machine cleaned - Bale retainer freed up and lubricated - Light barrier replaced - Twister unit completely disassembled, all bearings and plastic sliders replaced, greased, chain tension adjusted - Knife and counter-knife dismantled, sharpened, and reassembled - Knife gap readjusted - General maintenance performed and greased Scope of delivery for the baler: - 1 baler with wire spool boxes (without wire) - 1 set of machine documentation Comments: Complete documentation available (operating manual, CE declaration, electrical/hydraulic schematic). Viewing by appointment. We accept no liability for technical information or possible errors.

Būklė: geras (naudotas), Gamybos metai: 2002, Funkcionalumas: visiškai funkcionalus, Vertical baler HSM VL 600, year of manufacture 2002 Technical specifications: Manufacturer: HSM Model: HSM VL 600 Year: 2002 Pressing force: 60 t Drive power: 7.5 kW Cycle time (idle): 37 s Filling height: 1130 mm Filling opening: 1150 x 735 mm Bale size: 1200 x 1100 x max. 1200 mm Bale weight: 550 kg Weight: 3575 kg Materials: Paper, cardboard, film The press is in good condition and has been inspected and tested. A video is available on our website or YouTube channel. The operating manual and CE declaration are included. Hnsdpfxox Iryre Ab Ssi Viewing, including under power, is possible at any time by appointment. On request, we can also carry out tests with your material for an expense allowance. If you have any questions about the machine, we will be happy to answer them by phone from Monday to Thursday, 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data is based on the manufacturer's information. We accept no liability for the information provided or for any possible errors. The offer is non-binding, subject to prior sale, and can be withdrawn at any time. Inspection is possible by appointment. The sale is ex works, prepaid, without warranty or guarantee.

Būklė: naudotas, Gamybos metai: 1979, Funkcionalumas: visiškai funkcionalus, Bale Press Paal Pacomat II with Hopper, Year of Manufacture 1979 Technical Specifications: Manufacturer: Paal Model: Pacomat II Year of Manufacture: 1979 Drive Power: 11 kW Pressing Force: 27 t Channel Cross-Section: 700 x 1000 mm Filling Opening: 1000 x 650 mm Throughput: approx. 60/115 m³/h Bale Size: 700 x 1000 mm Bale Weight: up to 400 kg Machine Dimensions: approx. 7000 x 2000 x 2000 mm (LxWxH) Machine Weight: approx. 5,200 kg Materials: Paper, Cardboard, Film Remarks: Hjdox Irvaopfx Ab Ssni The machine is in working condition. It has been inspected and tested at our facility in 28816 Stuhr. The video can be found on our website or YouTube channel. Inspections, including under power, are possible at any time by appointment. Upon request, we can also perform tests with your material for a handling fee. We are happy to answer any questions about the machine by phone from Monday to Thursday between 08:00 and 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data is based on the manufacturer's specifications. We do not accept liability for the information provided or for any possible errors. Offers are non-binding, subject to prior sale, and may be withdrawn at any time. Inspections are possible by appointment. Sale is ex location, without warranty or guarantee. Our payment term is 100% advance payment.

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 2012, spaudimo jėga: 40 t, Gamintojas: HSM Modelis: HL 4010 Hnsdpfx Absx D U N So Soi Pagaminimo metai: 2012

Būklė: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2026, The BTS-MF450HD Special Baler is the ideal baler for compacting challenging materials such as PET bottles, cans and metal containers, big bags, plastic canisters, and plastic packaging. It can also reduce the volume of used tires and car bumpers to a minimum. The baler impresses with its simple and safe operation and large loading capacity, making it perfect for medium to large volumes of material. By compacting these waste and recyclable materials, you can achieve up to 90% volume reduction, significantly lower your disposal costs, and ensure the material is properly returned to the recycling cycle. Pressing force: 30 tons Bale weight: up to 450 kg (depending on material) Bale size: 1000 H (var.) x 1200 W x 800 D mm Machine dimensions: 3343 H x 1781 W x 1196 D mm Machine weight: 1600 kg Transport height: 2300 mm Loading aperture: 1200 W x 680 H mm Pressing cycle time: 40 seconds Motor: 5.5 kW, 16 Amp Power supply: 380 - 400 V (3-phase) Noise level: 68 dB Extra-long double cylinders for even and early material compaction User-friendly lever operation Bale ejector for easy bale removal Special retention claws to minimize material spring-back Holder for 4 rolls of strapping tape A quality product “Made in Europe” Suitable for compressing: - PET bottles - Food cans and tin containers - Plastic canisters and plastic packaging - Used tires and bumpers - Big bags - Cardboard and films - Hard-to-compact recyclables Additional options: - Annual service with accident prevention inspection (UVV) - Machine color as per RAL - PLC control with automatic press cycle, bale-ready indicator and key-operated emergency stop - Vertical door - Strapping tapes/wires - 11 kW motor, 32 Amp The demo video shows the BTS-MF550HD Special Baler. Can press, can baler, PET baler, PET press, tire press, tire baler, tire compression press, can press, general baler, paper press, paper baler, cardboard press, cardboard baler, film press, paper bale press, waste baler, waste compactor, recycling press, waste compactor, residual waste press Hodpfovug Dyex Ab Sjni

Būklė: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2026, The BTS-MF550HD special baler is the ideal machine for compacting challenging materials such as used tyres, computer CRT housings, cans and metal containers, big bags, plastic canisters and packaging, as well as car bumpers, which can be reduced to a minimum volume. The baler stands out due to its simple, safe operation and large feed opening, making it optimal for medium to high material throughput. By compacting these waste/recyclable materials, you achieve up to 90% volume reduction, significantly lower disposal costs, and return the material properly to the recycling cycle. Pressing force: 50 tonnes Bale weight: up to 550 kg (material dependent) Bale size: 1200 H (variable) x 1500 W x 800 D mm Machine dimensions: 3570 H x 2115 W x 1200 D mm Machine weight: 1935 kg Transport height: 2500 mm Feed opening: 1500 W x 780 H mm Pressing cycle: 50 seconds Motor: 5.5 kW 16 Amp Power supply: 380 - 400 V (3 phase) Noise emission: 68 dB Extra-long double cylinders for uniform and early material compaction User-friendly lever operation Bale ejector for convenient removal of bales Hnedpfx Aszd Rvjb Sei Additional retainers to reduce material spring-back Holding device for 5 rolls of strapping A quality product "Made in Europe" Suitable for compacting: Used tyres Food cans and metal containers Plastic canisters and packaging Bumpers Big bags Cardboard and film Difficult-to-compress recyclables Additional options: Annual maintenance with safety inspection (UVV test) Machine colour according to RAL PLC control with automatic press cycle, bale-ready indicator, and E-stop with key Vertical door Strapping tapes/strapping wires 11 kW 32 Amp motor Tyre baler, used tyre compactor, tyre press, can press, baler, paper baler, waste paper press, cardboard baler, film baler, paper bale press, waste baler, waste compactor, recyclable press, waste compactor, refuse compactor

Būklė: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2026, The BTS Tire Packing Machine Gen.2 is ideal for used tire businesses with high tire volumes. The triple tire packing machine is the perfect solution for cost-effective disposal or further marketing of second-hand tires. By doubling or tripling the tires, a significant volume reduction is achieved, allowing available storage and loading space, as well as the permissible transport weight, to be used much more efficiently. Press Cylinder: Pneumatic Pressing Force: 1.23 kN, adjustable Machine Dimensions: 1250 H x 1930 W x 660 D mm Machine Weight: 93 kg Transport Dimensions: 1250 H x 1200 W x 800 D mm Working Height: 800 - 1020 mm, adjustable Connection: Compressed air, up to 10 bar / 145 psi Operating Pressure: 6 - 8 bar Hnjdpfx As Ry Huob Soi User-friendly, safe two-hand operation Robust and durable construction High-performance pneumatic cylinder Ball bearing guide rollers Adjustable working height Extremely quiet due to muffler Quick-release compressed air coupling A quality product "Made in Germany" Suitable for bundling Used tires Optional features Machine color according to RAL BTS-MF550HD used tire baler The demo video shows the BTS Tire Packing Machine Gen.1; the BTS Tire Packing Machine Gen.2 operates in the same way. Tire packing machine, tire tripling machine, tire doubling machine, tire packer, tire doubler, tire tripler, tire handling, tire-packing, tire tripling machine

Būklė: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2026, The BTS-MF450 is the ideal baler for compacting your loose cardboard and film waste into a bale weighing up to 450 kg. This baler impresses with its simple and safe operation as well as its large feed opening, making it perfect for handling high volumes of material. By compacting these waste/recyclable materials, you achieve a volume reduction of up to 90%, significantly cut your disposal costs, and return the material properly into the recycling stream. Pressing force: 30 tons Bale weight: up to 450 kg (material-dependent) Bale dimensions: 1000 H (variable) x 1200 W x 800 D mm Machine dimensions: 3000 H x 1781 W x 1196 D mm Machine weight: 1300 kg Transport height: 2300 mm Feed opening: 1200 W x 680 H mm Press cycle time: 40 seconds Motor: 5.5 kW, 16 Amp Power supply: 380 – 400 V (3-phase) Noise emission: 68 dB Double-cylinder system for even material compaction User-friendly lever operation Bale ejector for easy removal of bales Retaining claws for minimizing material spring-back Bracket for securing strapping A quality product ‘Made in Europe’ Suitable for compacting: - Cardboard - Film - Big bags - Clothing - Light recyclables Additional options: - Annual maintenance and safety inspection (UVV test) - Machine color available in RAL Hedpfx Asvamafeb Sjni - PLC control with automatic press cycle, bale-ready indicator, and E-stop with key switch - Vertical door - Strapping bands - 11 kW / 32 Amp motor option Keywords: baler, cardboard baler, waste baler, paper baler, cardboard press, film baler, waste compactor, refuse press, recycling press, residual waste press

Būklė: naujas, Gamybos metai: 2026, Funkcionalumas: visiškai funkcionalus, Baler BTS-MF75 in stock and available for immediate delivery The BTS-MF75 is the ideal baler for compacting your loose cardboard and film waste into bales weighing up to 75 kg. With an additional pressing insert, it is also suitable for compressing individual metal and plastic containers as well as cans. The baler impresses with its simple and safe operation and large loading volume. By compacting these waste and recyclables, you achieve a volume reduction of up to 90%, significantly lower your disposal costs, and ensure proper return of the material to the recycling loop. Pressing force: 3.5 tons Bale weight: up to 75 kg (depending on material) Bale size: 1000 H (variable) x 700 W x 500 D mm Machine dimensions: 2335 H x 1040 W x 750 D mm Machine weight: 278 kg Transport height: 2335 / 1800 mm (if required) Loading opening: 700 W x 698 H mm Pressing cycle: 24 seconds Motor: 1.5 kW, 13 Amp Power supply: 230 V (single phase) Noise emission: 68 dB User-friendly lever operation Bale trolley for easy removal of bales Retainer to reduce material spring-back Strapping holder A quality product 'Made in Europe' Suitable for compacting: Cardboard Film Cans and lightweight metal containers Canisters and lightweight plastic containers Textiles Lightweight recyclables Additional options: Annual maintenance with safety inspection (UVV) Machine colour selectable according to RAL Can pressing insert PLC control with automatic press cycle, bale-ready signal, and key-operated E-stop Belt bale ejector + PLC (instead of bale trolley) Strapping bands Power supply 380 – 400 V (three phase) Baler, paper baler, waste paper baler, cardboard baler, cardboard box baler, film baler, paper bale press, waste baler, waste press, recycler press, waste compactor, refuse press, residual waste press Hodpfxsvah S Ae Ab Ssni

Būklė: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2026, The BTS-MF60HD special baler is ideal for compacting your challenging and tough materials such as cans, PET, metal buckets, and other tin containers; it also efficiently reduces plastics to a minimum. This special baler impresses with its easy operation and large feed opening. Finished bales can be conveniently removed using the automatic bale ejector. By compacting these waste/recyclable materials, you achieve a volume reduction of up to 90%, significantly reduce your disposal costs, and ensure the material is properly returned to the recycling loop. Pressing force: 13 tons Bale weight: 25 - 60 kg (depending on material) Hjdpfx Abevbq Rke Sjni Bale size: 650 H (var.) x 600 W x 400 D mm Machine dimensions: 2144 H x 1267 W x 1328 D mm Machine weight: 706 kg Transport height: 2144 mm Filling opening: 600 W x 400 H mm Press cycle: 25 seconds Motor: 2.2 kW, 16 Amp Power supply: 230 V (1 phase) Noise level: 68 dB User-friendly lever operation Bale ejector for convenient bale removal Material retainer to minimize material spring-back Cross strapping for secure bale stability Strap holder for strapping bands A quality product "Made in Europe" Suitable for compacting: PET bottles Cans and tin containers Canisters and plastic containers Cardboard and film Additional options: Annual maintenance with safety inspection (UVV) Machine colour available according to RAL chart Strapping bands Power supply 380 - 400 V (3-phase) PET press, PET baler, can press, can baler, special baler

Būklė: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2026, The BTS-MF450HD special-purpose baler is the ideal solution for compacting challenging materials such as PET bottles, cans and metal containers, big bags, plastic canisters and plastic packaging. It can also reduce old tires and car bumpers to a minimum volume. The baler is impressive due to its simple and safe operation as well as its large feed opening, making it optimal for medium to high material throughput. By compressing these waste and recyclable materials, you achieve up to 90% volume reduction, significantly lower disposal costs, and correctly reintegrate the material into the recycling stream. Pressing force: 30 tonnes Bale weight: up to 450 kg (depending on material) Bale size: 1000 H (variable) x 1200 W x 800 D mm Machine dimensions: 3343 H x 1781 W x 1196 D mm Machine weight: 1,600 kg Transport height: 2,300 mm Loading aperture: 1200 W x 680 H mm Pressing cycle: 40 seconds Motor: 5.5 kW, 16 amp Power supply: 380 – 400 V (3-phase) Noise level: 68 dB • Extra-long twin cylinders for consistent and early material compression • User-friendly lever controls • Bale ejector for easy removal of bales • Extra material retainers to minimize material spring-back • Holder for four rolls of strapping • A quality product "Made in Europe" Hnsdpfx Absvug Eks Sei Suitable for compacting: • PET bottles • Food and tin cans, metal packaging • Plastic canisters and packaging • Used tires and car bumpers • Big bags • Cardboard and film • Hard-to-compact recyclables Additional options: • Annual maintenance with safety inspection (UVV) • Machine color according to RAL • PLC control with automatic press cycle, bale-ready indication, and E-stop with key • Vertical door • Strapping bands / strapping wires • 11 kW 32 amp motor The demo video shows the BTS-MF550HD special-purpose baler. Keywords: can compactor, can baler, PET baler, PET press, scrap tire baler, tire baler, tire press, can press, baler, paper press, waste paper press, carton press, cardboard baler, film baler, paper baler, waste baler, waste press, recycling press, waste compactor, refuse press, residual waste press.