Dažų Pašalinimas pirkti naudotą (384)

Sąlyga: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, bendras aukštis: 5 600 mm, bendras ilgis: 11 200 mm, bendras plotis: 5 100 mm, įvesties srovės tipas: trifazis, garantijos trukmė: 24 mėnesiai, vidinis aukštis: 4 970 mm, vidinis ilgis: 11 000 mm, temperatūra: 80 °C, vidinis plotis: 5 000 mm, oro poreikis: 52 000 m³/val, įėjimo įtampa: 380 V, šildymo galia: 250 kW (339,91 AG), galia: 45 kW (61,18 AG), kuras: suskystintos naftos dujos (LPG), įėjimo dažnis: 50 Hz, energijos suvartojimas: 45 kWh, izoliacijos storis: 50 mm, nominali galia: 250 kW (339,91 AG), plieno lakšto storis (maks.): 2 mm, Įranga: apšvietimas, * Air Treatment Unit: The air treatment unit is a recirculation system that supplies the cabin with filtered fresh air and expels used air during the painting process. It heats the air to 60°C, mixes 10% fresh air with recirculated air via an automatic multi-damper system, and reheats the air before it is fed back into the cabin. Air is heated using a burner and heat exchanger, both made from high-grade 304 stainless steel and housed in the fresh air unit. During painting, the air passes through two stages of filtration (front and ceiling filters) before entering the cabin. The contaminated air is also filtered twice (inlet and outlet filters) before leaving through the extraction unit. Air treatment units are insulated like the side walls to minimize heat loss and are equipped with rubber seals on the covers to protect against possible vibrations and noise. The exhaust air is regulated by a damper in the exhaust air duct, which helps control the cabin’s internal pressure. * PRINCIPLE OF OPERATION FOR THE CABIN: Processes inside the cabin are controlled via an operator panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passes through front filters before entering the distribution chamber at ambient temperature. The air is then extracted through the exhaust unit. Floor filters (paint stop) capture paint particles, and the air passes through final exhaust filters before being released. * FLASH-OFF PROCESS: After painting, the cabin continues to operate for about 15 minutes to expel residual solvents and thinners. During this process, fresh air from outside circulates in the cabin. * DRYING PROCESS: In this phase, 80% of the air circulating through the cabin is heated to 60°C and supplied to the cabin via the distributor. Since 20% of the solvents are released during drying, they are expelled along with this air. Industrial paints are generally dried at 60°C, though the cabin temperature can be adjusted via the operator panel as needed. * COOLING PROCESS: After the 30-minute drying phase, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system is restarted. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices integrated into the cabin. The panel is constructed from robust galvanized sheet metal and steel profiles, and is fully enclosed for protection from dust and moisture. Electrical Components and Switching Panels: • The switching panel includes all necessary components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for control and command connections between the control panel and motors or other electrical devices. • Wiring is designed to allow for cabin relocation, if required. Pedpfxswzl Hxo Afwsrd • Operating equipment is powered at 380 V 50 Hz, while control devices run at 220 V.

Gamybos metai: 2020, Sąlyga: naujas, ROMER manipulators are distinguished by their quiet operation. They can handle both simple, common processes as well as complex, multi-dimensional tasks. Programming is performed via a PLC control system. Capable of operating with both long and short strokes. The toothed belt drive ensures quiet running. Podsf Aad Nepfx Afwsrd Maintenance-free AC motor. Slim column design saves space. The robust construction of the manipulators provides high versatility and stability. The manipulator is equipped with a 7" touch panel or can be controlled externally via the ModBus protocol using RJ45 cables.

Sąlyga: naujas, Gamybos metai: 2025, FILTER WITH DIAPHRAGM PUMP!!! A bath for removing paint layers from rims and other items coated with various types of paints, solvent-based varnishes, and powder coatings. Prodjgwg Haspfx Afwod Working basket dimensions (mm): 1250 x 800 x 700 mm * The bath is made of high-quality acid-resistant 304 stainless steel. * Fully insulated on all sides with 40 mm of insulating material, allowing for efficient and rapid heating of the liquid to the desired temperature. * The device housing is made of stainless steel. Device equipment: - Indirect heating (heating mantle), - Automatic temperature control of the heating medium, - Baskets made entirely of stainless steel, - LED indicator lights, - Ceramic heaters in the lid made of 2 x 4.5 kW acid-resistant tubes, - Aeration system for the entire bottom of the bath, - 12-month warranty. Our equipment is manufactured with great care and attention to detail. CHOOSE BUMEX SP. Z O.O. Very high quality of machines offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Complete technical documentation. 100% satisfaction of our customers. All products from BUMEX SP. Z O.O. are certified with a WE certificate. We offer our own transport – prices to be agreed upon for each specific offer. Invoices with stated VAT can be issued. Short lead times! Possibility to order machines in various, customized configurations and dimensions! Please do not hesitate to contact us.

Sąlyga: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, Pilnai automatizuota miltelinio dažymo linija Prsdpfov Nvtgex Afwed Ilgis: 30 m, Aukštis: 3,5 m Mūsų patyrusi komanda rengia individualius dizainus ir nestandartinius matmenis kiekvienam projektui. Dėl detalesnės informacijos apie miltelinio dažymo liniją prašome susisiekti su mumis. Konvejerių sistema Konvejerių sistema – tai dažnai naudojama mechaninio transportavimo įranga, skirta medžiagoms perkelti iš vienos vietos į kitą. Konvejeriai ypač naudingi transportuojant sunkius ar didelių gabaritų krovinius. Konvejerių sistemos leidžia greitai ir efektyviai pervežti įvairias medžiagas, todėl jos plačiai taikomos medžiagų sandėliavimo ir pakavimo pramonėje. Konvejeriai taip pat naudojami ir vartojimo sektoriuje, pavyzdžiui, prekybos centruose ar oro uostuose, kur jie užtikrina paskutinę prekės ar bagažo pristatymo stadiją klientui. Priklausomai nuo pramonės poreikių, naudojama įvairių tipų konvejerių – nuo grandininių (grindinių ir kabamųjų) iki uždarų bėgių sistemų, I-sijų, towline tipo, su galingumo paskirstymu („power & free“), ar rankiniu būdu stumdomų vežimėlių. Priežiūra ir aptarnavimas Konvejerių sistema – tai dažnai svarbiausia grandis, lemianti įmonės gebėjimą efektyviai ir laiku perkelti savo produkciją. Siekiant užtikrinti sistemų našumą, būtinos reguliarios apžiūros ir auditai, nuolatinė variklių bei reduktorių priežiūra, svarbiausių atsarginių dalių laikymas sandėlyje bei tinkamas darbuotojų apmokymas. Norint pailginti konvejerių sistemos tarnavimo laiką, būtina pasirinkti tinkamą konvejerio tipą, teisingai suprojektuoti sistemą ir laikytis reguliarios techninės priežiūros. Tinkamai suprojektuota konvejerių sistema su tinkama priežiūra tarnaus ilgus metus. Kabamieji konvejeriai naudojami įvairiose srityse: nuo prekybinių erdvių vitrinų, surinkimo linijų iki dažymo cechų ir kt. Pritaikymo sritys Konvejerių sistemos plačiai taikomos įvairiose pramonės šakose dėl akivaizdžių jų privalumų: - Saugiai perkelia medžiagas tarp skirtingų lygių, kitaip reikalautų daug darbo jėgos ir išlaidų. - Lengvai įrengiamos beveik bet kurioje vietoje, saugesnės nei krautuvai ar kita technika. - Gali transportuoti įvairių formų, dydžių ir svorių krovinius; daugelis sistemų turi pažangias saugos funkcijas, užkertančias kelią nelaimingiems atsitikimams. - Konvejerių sistemas galima automatizuoti – yra hidrauliniai, mechaniniai bei pilnai automatizuoti variantai, pritaikomi individualiems poreikiams.

Gamybos metai: 1987, Sąlyga: naudotas, mašinos/transporto priemonės numeris: 29990, Flow rate: 300 cm³ Overpressure: 231 bar Podpsbnpc Uefx Afword Maximum flow rate at 25 DH/min: 7.5 l/min Input overpressure or required air pressure: 7 bar Air consumption: 9.7 l/DH Weight: 100 kg Space requirement: 1250 x 750 x 1400 mm

Sąlyga: labai geros būklės (naudotas), Funkcionalumas: visiškai funkcionalus, stand for drying elements after painting, double-sided, shelf length 780 mm, maximum spacing 2520 mm, minimum spacing 350 mm, 22 shelves, rods coated with rubber, mobile design, distance between rods 115 mm Prsdpfx Ajvcb Ivjfwod

Sąlyga: beveik kaip naujas (parodų įrenginys), Funkcionalumas: visiškai funkcionalus, Cobra je ekskluzivna visokotlačna dvostruka membranska pumpa, prikladna za Airless i AirCoat primjene do 250 bara. Cobra je prva visokotlačna pneumatska pumpa bez brtvenih pakunga. Zahvaljujući odsutnosti kontakta između materijala i vanjske atmosfere (pumpa je potpuno zatvorena), odsustvu trenja u fluidnoj sekciji te minimalnom smicanju, savršena je za sve vrste materijala, uključujući najzahtjevnije kao što su reaktivne boje (UV boje, izocijanati, akrilati) ili izrazito abrazivne materijale. Pumpa radi s izuzetno niskim pulsiranjem i osigurava ujednačen protok boje, postižući savršen uzorak raspršivanja i izvanrednu površinsku kvalitetu. Zbog minimalnih unutarnjih volumena, konstruirana je tako da znatno smanji potrošnju otapala i gubitak materijala tijekom ispiranja i promjena boje. Cobra 40-10 je idealno rješenje za rad s manjim količinama i čestim promjenama boje – preporučuje se za primjene s jednim do tri pištolja u drvnoj i namještajarskoj industriji, malim stolarskim radionicama te u općoj metalnoj industriji. Cobra® 40-10 je također idealna za dovođenje baze ili učvršćivača do 2K miješalica (FlexControl i FlexControl Plus). Wagner membranska pumpa OMJER PRITISKA 40 :1 MAKS. TLAK MATERIJALA NA ULAZU PUMPE 20 bara Prsdpoqzx Nksfx Afwsd DOVOD MATERIJALA M-M 36x2 IZLAZ MATERIJALA M-G 3/8’’ TEMPERATURA MATERIJALA 10 - 80 °C ULAZNI TLAK ZRAKA 2,5 - 6,0 bara PRIKLJUČAK ZA ULAZ ZRAKA F-G ½’’ RADNI TLAK 250 bara MAKS. BRZINA UDARA 200 DS/min VOLUMETRIJSKI PROTOK PO DVOSTRUKOM UDARU 10 cm3/DS TEMPERATURA OKOLINE 10 - 60 °C TEŽINA 19,0 kg MAKS. RAZINA ZVUKA 74 dB(A) MATERIJAL PH 3,5 - 9,0 pH PUMPA DOLAZI U KOMPLETU S CRIJEVOM I PIŠTOLJEM GM4700AC

Sąlyga: naujas, These units are made from galvanized sheet metal and are designed to be fully bolted together. This requires very little space during shipping. The extraction system is developed separately and tailored specifically for each booth to ensure optimal extraction performance. Thanks to the extraction, personnel applying wet paint are not inconvenienced by paint fumes or overspray. In Elboy Wetline-KF wet paint spray booths, environmental pollution is prevented through the use of a filtration system comprising accordion filters and either cartridge or rolled fiberglass filters. Pjdody Dv Djpfx Afwsrd Wet paint particles extracted from the air by the suction fan are captured by the accordion filter located at the rear of the booth. Trace amounts of wet paint particles that are not caught by the accordion filter are retained by the secondary fiberglass filter at the rear. The door system can be installed in various ways at the front access. UV lamps can be integrated into the cabinet to inspect the painting process.

Sąlyga: naujas, Gamybos metai: 2025, Paint Stripper for 4 Wheels. A bath designed for removing paint layers from rims and other items coated with various types of paints, solvent-based varnishes, and powder coatings. Basket working dimensions (mm): 1150 x 650 x 650 * The bath is made of high-quality, acid-resistant 304 stainless steel. * Fully insulated on all sides with 40 mm insulation material, allowing for efficient and rapid heating of the fluid to the desired temperature. * The unit's housing is made of stainless steel. Equipment features: - Indirect heating (heating jacket), - Automatic temperature control for the heating medium, - 2 baskets made entirely of stainless steel, - LED indicator lights, - Ceramic heaters in the lid made of 2 x 4.5 kW acid-resistant tubes, - Fume extraction hood, - Ventilation system for the entire bottom of the bath, - 12-month warranty. Our equipment is manufactured with great care and attention to detail. CHOOSE BUMEX SP. Z O.O. Very high quality of machines offered on the market. Professional advice and service. Warranty. Warranty and post-warranty service. Complete technical documentation. 100% customer satisfaction. All BUMEX SP. Z O.O. products are WE certified. Prjdpfxefmf Ize Afwed We offer our own transport – prices are agreed individually for each offer. We issue VAT invoices. Short lead times! Option to order machines in various, personalized configurations and dimensions! Please do not hesitate to contact us.

Sąlyga: naujas, Gamybos metai: 2020, veikimo valandos: 1 h, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: PUBMANUAL000168, Įranga: dokumentacija / vadovas, SWISS KRONO Kft. offers for sale a Giardinagroup automatic spray painting system along with the corresponding drying chamber. We have provided a description of the machines, as well as additional images and information, in a shared folder attached to this listing. Podorxubpepfx Afwjrd

Sąlyga: naujas, Gamybos metai: 2025, bendras aukštis: 4 000 mm, bendras ilgis: 7 000 mm, bendras plotis: 3 000 mm, garantijos trukmė: 24 mėnesiai, temperatūra: 80 °C, oro poreikis: 36 000 m³/val, įėjimo įtampa: 380 V, šildymo galia: 345 kW (469,07 AG), galia: 40 kW (54,38 AG), kuras: suskystintos naftos dujos (LPG), energijos suvartojimas: 40 kWh, izoliacinė medžiaga: Mineralwolle, izoliacijos storis: 50 mm, nominali galia: 345 kW (469,07 AG), Įranga: apšvietimas, Sales Price List Pony 7000 Paint Booth 7 x 4 x 3 meters • Reinforced partial grating 5 mm • Height 3 meters (Sprinter height) • 2 x 7.5 kW motors (belt drive) • Ceiling lighting ATEX • 24,000 m³/h • Incl. 2 drive-on ramps for above-floor version • Above-floor and in-ground configurations at same base price Base price: €28,900 Base price for height of 2.76 meters (passenger car height): minus €1,000 Base price for height of 3.5 meters (motorhome height): plus €1,000 Door-in-door system: €1,800 Double glazed doors: €1,800 11 kW motor incl. larger fans: €7,770 with expanded control cabinet and direct drive 15 kW motor incl. larger fans: €8,610 with expanded control cabinet and direct drive Side lighting: €2,870 Ceiling lighting with EX protection acc. to ATEX: €1,470 Full grating Light: €1,785 Full grating fully reinforced 5 mm: €2,990 Direct drive with PLC control for 11 kW motors (incl. soft start): €15,120 Direct drive with PLC control for 15 kW motors (incl. soft start): €17,640 Soft start for 7.5 kW motor (belt drive only): €1,239 PLC control for 7.5 kW 24,000 m³/h motors with 3-stage energy saving program: €5,670 PLC control for 11 kW 30,000 m³/h motors with 3-stage energy saving program: €7,770 PLC control for 15 kW 30,000 m³/h motors with 3-stage energy saving program: €8,610 PLC control for 2 x 5.5 kW 36,000 m³/h (belt drive) motors with 3-stage energy saving program: €5,565 Pneumatic drive-on ramp: €4,900 Pjdpfx Afowzmcbowsrd Grating modification for lifting platform: €1,785 Drive-through system with double doors (without door-in-door): €3,250 Tri-axis ramp: €7,980 Second service door (position freely selectable): €1,150 Note: 11 kW motor set to 1200 rpm (inverter) (1,000 rpm standard) can achieve 36,000 m³/h

Gamybos metai: 2011, Sąlyga: paruoštas naudoti (naudotas), A complete paint shop system is available. Components: (1) Overhead conveyor, (2) Spraying zone/brush wall, length: 4000 mm, width: 1500 mm, height: 4800 mm, equipped with Maxon burner, exhaust duct, drawers for dry paint residue disposal, six filter mats, various filters, (3) Flash-off area, (4) Drying booth, length: 6500 mm, width: 5200 mm, height: 3150 mm, equipped with Weishaupt WG10N/1-D ZM-LN gas burner. Total system dimensions: 24,000 mm / 10,000 mm, max. output: 45 kW. Documentation is available. Prjdpfx Ajup Ehiefwod

Sąlyga: geras (naudotas), Funkcionalumas: visiškai funkcionalus, Didelio slėgio stūmoklinė-membraninė pompa. Universalus naudojimas agresyviems, abrazyviniams arba šlyčiu jautriems produktams. Labai mažos skalavimo skysčio sąnaudos. Visoms reikmėms iki 250 bar ir 5 l/min. Tiekia iki 8 AirCoat purškimo pistoletų. + 3 automatiniai AirCoat purkštuvai su vidine valdymo sistema, skirti montuoti automatizuotose dažymo linijose. Psdexmf Svepfx Afwjrd +JUNGTYS+ORO/GAMINIO ŽARNA

Sąlyga: naujas, bendras aukštis: 3 500 mm, bendras ilgis: 7 000 mm, bendras plotis: 4 000 mm, tūrio srautas: 26 000 m³/val, garantijos trukmė: 12 mėnesiai, vidinis aukštis: 2 700 mm, vidinis ilgis: 6 900 mm, vidinis plotis: 3 900 mm, darbinio aukščio: 2 700 mm, Įranga: dokumentacija / vadovas, kabina, ⭐⭐⭐⭐⭐ (5.0) Customer Rating – Proven Quality! ⚡ Top Service – Fast Delivery – Reliable Support ⚡ ✈️ Plus shipping costs – Shipping available on request ⏰ 48H EXPRESS DELIVERY possible after deposit! Regular delivery time varies by stock availability between 1 business day and approx. 15 weeks. 🔧 Please note: Additional options may extend delivery times. 📩 Please inquire with the seller in advance to check immediate availability of your selected options. 🛒 ►►► Buy Now! ◄◄◄ 💸 Preserve liquidity – invest wisely! ✳️ We offer flexible financing options: ✔️ Hire purchase ✔️ Leasing ✔️ Warranty programs 📞 Contact us – we will find the right solution for your budget! ✨ Powerful. Economical. Efficient. ✨ 📦 Immediately available in three standard sizes! 📌 Our three most common cabin sizes are generally in stock and available at short notice. 📌 If larger paint areas are needed, we can modularly combine standard cabins to create tailor-made solutions – fully adapted to your space and process requirements! 🎨 PROTON WETLINE KKF-40-70-35 Premium Wet Paint Spray Booth & Drying System 📐 Technical Data (Internal / External): Length: 6900 mm / 7000 mm Width: 3900 mm / 4000 mm Height: 2700 mm / 3500 mm Air Preparation Box: 1350 x 2900 mm 🔧 Features: 🌬️ Vertical airflow via full-surface ceiling inlet plenum – for uniform, dust-free coating 🚪 3-wing main gate with viewing windows + service door with emergency lock in case of overpressure 💡 Shadow-free lighting, heat-resistant and compliant with standards ♻️ Recirculation system with controllable fresh air damper – rapid heat-up to 60–80°C in 8–15 min 🔇 Low-noise high-performance fans with constant airflow (0.30 m/s) 🛡️ Slight overpressure reliably protects against dust ingress 🔥 Heating System & Efficiency: Riello G20 Burner Heating power: approx. 200,000 kcal/h Efficiency: up to 99 % High-temperature heat exchanger made of special steel 🧼 Highest Standard Filtration Technology: ✅ Pre-filter (tear-resistant, up to 100 °C, DIN 53438-3 F1) ✅ Ceiling filter (EN 779: F5, polyester coated) ✅ Floor filter (Paint Stop, G3, silicone-free) ✅ Activated carbon filter (DIN 24184, Class G4) 🖥️ Intelligent Controls: Modern control panel for complete management of ventilation, heating, lighting, and safety – easy operation & standard-compliant 🖲️ Optional touchscreen control available 🧱 Flexible placement of air prep units – installable to the right, left, or rear of the cabin ➕ Optional Equipment (at surcharge): 🪟 Full-glass panorama gates 🧱 Roof with additional insulation 🎨 Integrated paint mixing station 🌈 Color selection: Any RAL color possible (standard: blue, white, orange, red, grey) 💡 Explosion-proof lighting (Exproof) 🌪️ Explosion-proof fan (Exproof fan) 🖥️ Touchscreen control system ⚠️ Choosing special equipment may extend delivery times. Please coordinate your options with our sales team in advance. 🚧 Installation costs not included in the price. Pjdpfx Aeipvulofwjrd 📍 These depend on your location – we will gladly provide you with a tailored quote! ☀️ 2-YEAR WARRANTY – Safe is safe! ☀️ ⭐ Follow us for new offers & promotions! ⭐ PROTON Maschinenbau GmbH – Your partner for professional painting technology with over 40 years of experience.

Gamybos metai: 2007, Sąlyga: geras (naudotas), Funkcionalumas: visiškai funkcionalus, Paint Drying Chamber MEYER AB / Fanmet OY 17m³ Year of manufacture: 2007 (installed in 2009) Manufacturer: MEYER OY Finland Previously used for drying painted furniture components. Loading via rack trolleys Dimensions: Length: 3,600 mm Width: 2,150 mm Height: 2,200 mm Approx. 17 m³ capacity Electric heating Total power: 30 kW 18 heating elements, each 1,667 W, 400 V (length: 2,360 mm) Airflow: 3 m³/sec or 10,000 m³/h Internal cladding: galvanized steel sheet 2 VEM fan motors (3.6 kW + 0.37 kW), ATEX certified Thermostat: 0–120°C Overheating protection: 0–210°C Psdpstt Sy Rsfx Afword ATEX compliant according to 94/9/EC CE marked

Gamybos metai: 1994, Sąlyga: geras (naudotas), Working area approx. 2,080 x 1,430 mm, side impact plates on right and left, filter surface approx. 1,800 x 1,300 mm, 2 rows of paper volume filters approx. 650 x 1,800 mm, internal fine filter G4 approx. 1,350 x 2,000 mm, air capacity 4,500 m³/h, max. pressure 500 Pa, motor 1.1 kW / 1,400 rpm. Pjdpjpvil Tefx Afwsrd

Sąlyga: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, bendras aukštis: 3 500 mm, bendras ilgis: 7 050 mm, bendras plotis: 4 100 mm, tūrio srautas: 36 000 m³/val, temperatūra: 80 °C, įėjimo įtampa: 380 V, šildymo galia: 250 kW (339,91 AG), Įranga: apšvietimas, kabina, Paint and Drying Booth It is the centerpiece of your entire painting process: the combined paint and drying booth. (Optionally also available as a separate paint booth with a separate dryer.) Here, we rely on full-surface ceiling filters and, optionally, a full-surface floor extraction system with drive-over grating or wall extraction at the position of your choice. Psdpfx Afjxa H Ewswsrd If you would like to further increase the efficiency of the system beyond heat recovery and stepless control via frequency converters, we are pleased to offer you a sectional control system. This allows you to activate only the section where the parts are located—in the case of repair painting or partial booth loading (for example, if you only want to paint add-on parts). You benefit from being able to operate with reduced air volume, maintain the same quality standards, and save energy—and, ultimately, real money. Just ask us—we would be happy to demonstrate these options to you in more detail. Do you have questions or suggestions? We're happy to assist you.

Sąlyga: naudotas, Vibration screed, float trowel, concrete finishing machine - Electrically powered - Connection: 230 Volt - Working width: 1500 mm - Dimensions: 1500/350/H450 mm - Weight: 17 kg Psdpeb A Swrjfx Afwjrd

Sąlyga: naujas, Mobile design High separation efficiency & high extraction performance Easy to handle Long filter life – resulting in minimal downtime Flexible thanks to extraction technology with front plate system Podpfx Ajhby Risfwerd Motor data: 0.75 / 2.1 kW ex / 400 V / 50 Hz Speed: 960 / 1,430 rpm Airflow: 3,000 / 6,800 m³/h Usable pressure: 400 / 500 Pa Dimensions (W/ H/ D): 1,912 x 1,405 x 943 mm with side panels folded out: 2,971 x 1,405 x 1,215 mm Filter area: 2 m² Sound pressure level: 72.0 dB(A) Weight: 248 kg

Sąlyga: naujas, AUTOMATED PAINT SHOPS These are the paint shops where your product is designed and manufactured by our engineers in accordance with your capacity, application area, and other requirements. Prodpedy Ez Isfx Afwod Maximum efficiency is targeted by providing electrostatic powder or wet painting, sandblasting, painting, glazing, coating, washing, and similar system requirements with minimal staff and minimal space requirements.

Sąlyga: paruoštas naudoti (naudotas), mašinos/transporto priemonės numeris: 89915, Drive: Compressed air, Material/air ratio: 16:1, Maximum material pressure: 90 bar, Pjdsiv Huwopfx Afwerd Air inlet pressure: 1 to 6 bar, 4 double strokes per 1 liter of material, Includes MX-type spray gun with twin hose, Unused since last maintenance (01/20), Condition as inspected, Ex stock Seevetal, subject to prior sale.

Sąlyga: naujas, Powder Coating Systems For years, powder coating has been evolving as an alternative to wet painting and has recently gained even greater importance due to its lower environmental impact, with no solvents or paint sludge produced. Especially the possibility of powder recovery enables an exceptionally high level of efficiency. For the user, powder coating offers the advantage of creating an extremely durable and corrosion-resistant surface, which is significantly more impact-resistant than what paint can provide. Additionally, post-processing such as sanding or drilling coated parts is easily possible without the coating chipping off. Pony Luxury Coating powder coating systems thus offer you tangible benefits: they are efficient, environmentally friendly, and, of course, unbeatable in terms of flexibility, as always. We achieve this with various system types. Manual Powder Coating Systems Podpsxa Hzxefx Afwerd Systems that are operated manually are the ideal solution for demanding and complex workpieces. Trained staff can flexibly adapt to new conditions and continually changing product sizes. Flexibility is the top priority and is also complemented by an attractive entry price into the world of powder coating. Large-Volume Powder Spray Booths No matter how large and challenging your workpieces are, our systems are bigger! Due to the high demands in the commercial and utility vehicle sectors, powder coating has established itself here as the perfect solution. To accommodate increasingly larger components, we offer our large-volume powder booth, which allows for unrestricted manual coating and, in combination with a conveyor system, can handle workpieces of any size. Automatic Powder Coating Systems If your focus is on high throughput and rapid process speed, then an automated powder coating system is the future for your operation. Coupled with a conveyor system, light grids precisely detect and, as a result, perfectly dose the powder quantity to ensure optimal efficiency. Of course, the system can also be equipped with lifting stations and robots to handle even the most complex components. Powder Curing Ovens & Adhesion Water Dryers The perfect finish to a powder coating process: the curing oven. Equipped with the highest insulation class, our unwavering efficiency continues in this area as well. Precise temperature control also allows use as an adhesion water dryer, enabling pre-treated materials to be dried after pre-cleaning. Additionally, temperatures up to 250°C are possible, allowing for use as a tempering oven, for example, for hot-dip galvanized materials. The typical use as a powder curing oven is, of course, easily accomplished. Optimal air distribution and a visualized control panel prevent burning and even allow for simultaneous curing of different color tones. Do you have questions or suggestions? We are happy to help you!

Sąlyga: naudotas, lacquer casting machine, lacquer casting station, lacquer pump, emulsion pump, dosing pump Podpfx Aofv H Aiefwsrd - Gearbox: Stöber type R27-0000-110-4 - Speed: 800 - 1820 rpm - Motor: HEW type EEXF-S/4 - Power: 1.1 kW - Dimensions: 300/400/H935 mm - Weight: 43 kg

Sąlyga: naujas, Įranga: kabina, Stationary Small Spray Booth Dixi █████ Perfect and uniform coating of small parts. The extraction system ensures optimal results in minimal space. Optionally equipped with a rotary table or a wheel mount, as well as a compact yet powerful extraction unit, it is ideally suited for processing small workpieces and rims. The side panels effectively limit overspray distribution, making it possible to work in small areas without contaminating surrounding spaces. Integrated lighting is also available. In addition, thanks to its low weight and minimal connections, it can be relocated to a new site in no time, maintaining your operational flexibility at all times. The system comes fully pre-assembled. Your Advantages With its compact design, flexible dimensions, and adaptable accessories, this unit offers a wide range of applications. The sophisticated modular system has a minimal footprint, making it suitable for use in any space. The various filter media and stages ensure highly efficient operation and make filter changes a matter of minutes. Application and Safety Thanks to the use of ATEX-certified explosion-proof motors, processing both water-based and solvent-based coatings is possible without issue. Optionally, it can also be configured for adhesive spraying. The large filter surface ensures uniform extraction throughout the booth. Prodpfx Afjxa Hx Rjwsd

Sąlyga: naudotas, Gamybos metai: 2024, Please find below information about our powder coating and wet painting line, which we installed last year in the Izmir Free Trade Zone. The facility is used for bicycle coating. The dimensions are 680 × 680 × 2100 mm (L × W × H). Facility includes: 1. 5-stage washing system, 2-tank plate heat exchanger, and heated stainless steel 316 sheet 1.1. Water drying tunnel with reversing function, 135 m 1.2. Control panel 1.3. Medium-sized overhead conveyor 2.1. Labeling oven and conveyor belt, 75 m 2.2. Labeling area with air-conditioned roof and conveyor 3.1. Powder coating line, 135 m 3.2. Powder curing oven with 2 reversing functions 3.3. Powder coating booths do not belong to us, Wagner 2 powder coating booths 3.4. Medium-sized overhead conveyor Prsdpexa Expofx Afwsd 4.1. Wet powder coating system 4.2. Powder curing oven 4.3. Wet paint curing oven 4.4. Exhaust air system 4.5. 4 wet spray booths 4.6. 2 air-conditioned mixing rooms 4.7. 290 m conveyor 5.1. Label applicator unit, 90 m 5.2. Air-conditioned roof room The purchase price as new was €2,800,000.00. This is a fully-automatic powder and wet paint coating line. Individual components may also be purchased separately. Should you be interested, we are happy to assist you.