Lakštinio metalo briaunų apdirbimo staklės

EVOTEC 1300SRS

Sąlyga: labai geros būklės (naudotas), Gamybos metai: 2024, Funkcionalumas: visiškai funkcionalus, darbinis plotis: 600 mm, įėjimo įtampa: 400 V, bendras svoris: 3 560 kg, ruošinio aukštis (maks.): 170 mm, The fast deburring machine for deburring, edge rounding, and finishing steel parts up to 600 mm wide. This deburring and finishing machine from Q-Fin has been specifically developed for applying a large radius of up to 2 mm to steel sheet. With the SER600 Super Edge Rounder from Q-Fin, it is possible to deburr, grind, edge-break, round, descale, remove oxidation layer, or apply a linear finish to sheet metal parts up to 600 mm in width. A combination of these operations is also possible. The throughput rate of the SER600 is 3 to 5 times higher than that of comparable machines. This new 2025 model is equipped with a magnetic support and is therefore suitable for processing steel cut parts and other magnetic materials. The machine features 5 processing stations. Operation is conveniently controlled via an HMI touchscreen on the front of the machine. The first station of the SER600 consists of a grinding unit. The abrasive belt in this station removes burrs and/or discoloration from the product surface. If there are no burrs present, the grinding belt can be omitted or removed. It is also possible to use a finer grinding belt or finish with a Scotch-Brite belt. The second and third stations consist of a disc brush unit with 4 oscillating disc brushes. The fourth and fifth stations are fitted with 2 round brushes rotating in opposite directions. These brushes are used to remove sharp edges from the product by breaking edges or, through the unique combination of two brush systems, by creating a radius of up to R=3 mm. By installing special brushes, the SER600 with magnetic system is also ideally suited for removing the oxide layer from steel products or slag from plasma-cut products. We offer the machine in combination with a WES6000 wet grinding dust extraction system as the 'SER600 Set'. The WES6000 was developed by Q-Fin to safely extract grinding dust without loss of suction. This fully stainless steel extraction system operates wet, extracting grinding dust from stainless steel, steel, and aluminium, thus eliminating fire and explosion hazards. According to Q-Fin, it is the safest, simplest, and most sustainable method of extracting grinding dust. With the WES6000, there is no longer any grinding dust in the air and/or the working environment. Blsdpfxol Dw D Eo Abfoc We currently have 2 units of the SER600 in stock: - 1x new (Year of manufacture: 2025) - 1x only a few months old, like new (Year of manufacture: 2024) The machines can be inspected by appointment in Bergeijk. Both machines come with a 1-year warranty on the construction and all non-wear parts. We can also offer on-site installation of the SER600 + WES6000, including operator training. - Electrical connection of the SER600: 400 V, 50 Hz, 32 A, 16 kW - Dimensions: 3640 x 1585 x 2085 mm (L x W x H) - Weight: 3560 kg

Sąlyga: naujas, Gamybos metai: 2025, -TFON – Sistema de Precisión para Redondeo y Acabado de Bordes Blodpfx Abshq A Txofsc -Diseñado para ofrecer acabados superficiales superiores y redondeo de bordes precisos en una amplia gama de materiales e industrias, el sistema TFON combina automatización avanzada con configuraciones versátiles para adaptarse exactamente a sus necesidades de producción. Compatibilidad de materiales: Adecuado para aplicaciones en aluminio, acero inoxidable y acero al carbono. Amplio rango de espesores: Procesa materiales de manera eficiente desde 0 hasta 120 mm de espesor. Excelencia en acabado: Especialmente diseñado para proporcionar acabados superficiales de alta calidad que mejoran la estética y la funcionalidad del producto. Versatilidad industrial: Ideal para los sectores de dispositivos médicos, equipamiento para cocinas industriales, piezas automotrices y accesorios metálicos. Precisión en redondeo de bordes: Proporciona un redondeo de bordes preciso con radio 2, mejorando la seguridad y la presentación del producto final. Automatización avanzada: Sistema de control Siemens integrado que garantiza una mayor precisión y fiabilidad operativa. Estaciones de procesamiento independientes: Permiten un procesamiento flexible y eficiente en múltiples etapas, adaptado a flujos de trabajo complejos. Opciones de ancho de mesa: Disponible en anchos de mesa de 650 mm, 1000 mm o 1300 mm para satisfacer diversos requerimientos de producción. Opciones personalizables de transporte: Elija entre sistemas de transporte por vacío, semi-magnéticos o semi-vacío para una manipulación segura y fiable de las piezas. Limpieza de superficie: Elimina eficazmente óxido, óxidos y contaminantes superficiales, preparando las piezas para procesos posteriores. Seguridad mejorada para el operador: La estación de redondeo minimiza el riesgo de cortes y lesiones por bordes afilados. Acabado de alto rendimiento: Equipado con tecnología de abrasivo Scotch para obtener acabados suaves y homogéneos. Mayor vida útil de abrasivos: El sistema de oscilación neumática maximiza la duración de las bandas abrasivas y de los abrasivos tipo Scotch, reduciendo los tiempos de parada. Producción uniforme de radios: Seis ruedas flap aseguran un radio de borde uniforme en cada pieza, garantizando una calidad constante. Diseñado para el rendimiento. Pensado para la seguridad. Construido para la versatilidad industrial. TFON – Perfección superficial, siempre.

Sąlyga: naujas, Gamybos metai: 2025, Technical Data - English --- Rated Power at 50% Duty Cycle: 20 kVA Short-circuit Current: 11.6 kA Electrode Force: 180 daN Throat Depth: 455 mm Arm Spacing, stepless: 173–410 mm Electrode Taper: Mk1 --- Welding Controller: WS 402 (4-step, 2-program) --- Incl. Additional Options: - Foot switch Bodjk E Hnujpfx Abfelc - Main switch - 3 m connection cable + 32A Cekon plug --- 6-month warranty --- Training + commissioning available on request --- Spot welding electrodes + spare parts available from stock --- Further information on our website

Sąlyga: naujas, DESCRIPTION DM100 Z2C – performs edge rounding and removes sharp burrs on both the inner and outer edges of steel, stainless steel, or aluminum parts after laser, shear, or punch separation of metal components ranging in size from 50 x 50 mm up to 1100 x 100 mm. The first station processes the products by means of a contact roller (approx. 55° Shore) with an abrasive belt, removing heavy burrs in the initial step. The second station processes the products with two counter-rotating cross belts from both below and above. The cross belts round the edges of the workpieces on both inner and outer sides. Bledpod Ixadjfx Abfsc A major advantage is the deburring of products with protective surface film, as only the edges are processed without damaging the film. Technical Data - DM1100 Z2C: Working capacity (Ø mm): 1100 x 100 Number of belt stations (Z): 1 Number of cross belt stations: 2 Abrasive belt dimensions (mm): 1100 x 2200 Abrasive belt speed (m/s): 8–22 Cross belt speed (m/s): 2–8 Feed speed (m/s): 0.6–3.2 Abrasive belt motor per head (kW): 18.5 Cross belt motor (kW) (2x): 3 Feed motor (kW) (3x): 0.18 Total power (kW): 33 Power consumption (A): 62 Extraction port per head (Ø mm): 150 + 185 Dimensions (mm): 3600 x 2330 x 2350 Weight (kg): 5000

Sąlyga: naujas, DM1100 2C – Edge Rounding Machine for Laser, Flame-Cut, and Punched Parts. NEW DESIGN – CAN BE VIEWED UNDER POWER – IMMEDIATELY AVAILABLE FROM STOCK The DM1100 2C rounds the upper and lower edges of metal parts from a minimum size of 150 mm up to a length of 1100 mm in a SINGLE PASS. The first station processes the workpieces from below using two counter-rotating cross belts, while the second station works from above, also with two counter-rotating cross belts. The cross belts allow deburring of both inner and outer edges of the workpieces. Bljdod Ev Upspfx Abfoc Sharp edges produced during laser cutting, punching, or shearing of steel, stainless steel, and aluminum parts are removed. Simultaneous processing of both sides of laser-cut or punched metal parts saves time and reduces production costs. Another advantage of the DM1100 2C is its capability to process small parts from 50 mm. By folding up a table, the rotating direction of the upper conveyor automatically reverses, and the gap of the first processing station is bridged, enabling the workpieces to feed directly into the second processing station. Thus, small products measuring from 50 mm up to 150 mm can be processed on one side only. An additional benefit of this machine is the ability to round parts with protective surface film without damaging the film. Easy and tool-free cross belt change. The program for automatic positioning of the upper and lower belts ensures good accessibility and reduces changeover times. User-friendly operation via integrated touch screen. This machine is also available with a return transport system upon request. Technical data: Working capacity (Ø mm) 1100x50 Number of cross-belt stations 2 Cross-belt speed (m/s) 2–8 Feed speed (m/s) 0.6–3.2 Cross-belt motor (kW) (4x) 3 Feed motor (kW) (3x) 0.18 Total power (kW) 13.1 Power consumption (A) 30 Extraction connection per head (Ø mm) 150 Dimensions (mm) 2560x1980x2150 Weight (kg) 2210

Gamybos metai: 2010, Sąlyga: paruoštas naudoti (naudotas), Parduodama Amada CNC lakštų lankstymo staklės. Darbinis plotis: 4000 mm, spaudimo jėga: 2200 kN, eiga: 350 mm, ašių skaičius: 8. Įrenginio matmenys (X/Y/Z): apie 5600 mm / 2650 mm / 3300 mm, svoris: apie 18 000 kg, valdymas: Amada. Galima apžiūra vietoje. Bedsxv A E Sjpfx Abfelc

Sąlyga: naujas, Funkcionalumas: visiškai funkcionalus, Comparable to Durma, Baykal, Ermaksan, etc. Bending length 3020 mm Press force 220 t Approach speed 140 mm/s Bending speed max. 10 mm/s Return speed 130 mm/s Stroke 350 mm Installation height 600 mm Throat depth 450 mm X-axis travel 750 mm X-axis speed 300 mm/sec R-axis travel 250 mm R-axis speed 100 mm/sec Clear distance between frames 2555 mm Machine length 3730 mm Machine width 2290 mm Overall height 3055 mm Table height 820 mm Motor power 22 kW Oil tank capacity 300 l Machine weight 11500 kg (Technical data may vary depending on equipment) Standard equipment: • 3 CNC axes (Y1, Y2, X) • Double-guided press beam, stable and precise • Robust double-guided backgauge • Manually adjustable backgauge fingers, double-guided on linear guide • Movable front arms with height adjustment • Lateral and rear safety covers • Lower die adapter rail 60 mm • Manual upper tool clamping system (Promecam system) • Manual crowning • Foot switch with emergency stop Bjdpjq D Dzlsfx Abfslc • 380 V, 50-60 Hz, 3 phase • LED lighting Including the following options: • Delem control DA 66T • Fiessler AKAS 2M laser finger guard • FPSC Safety PLC (manual) • X-R axis with servomotors • CNC crowning for high bending precision • 2 additional backgauge fingers - Other bending lengths and thicknesses are available upon request with the appropriate accessories! -

Sąlyga: naujas, Gamybos metai: 2024, Laser source: 12 kW Raycus/IPG Laser head: Precitec Pro-Cutter 2.0 Control system: FSCUT 8000 Effective working area: 1520x3050 mm Max. positioning speed: 120 m/min Max. acceleration: 1.5 m/s² Positioning accuracy: 0.02 mm/m Repeatability: 0.03 mm/m Max. table load: 1500 kg Blsdpfx Aoi Ar Rujbfoc

Sąlyga: naujas, Gamybos metai: 2025, - TFON Kantenverrundungs- & Oberflächenreinigungssystem. -Materialkompatibilität: Geeignet für Baustahl, Aluminium und Edelstahl. -Arbeitsthickenbereich: Verarbeitet Materialstärken von 0 bis 120 mm. -Kantenverrundung: Sorgt für eine Radius-2-Kantenverrundung für glatte, sichere Kanten, die sowohl das Erscheinungsbild als auch die Funktionalität des Werkstücks verbessern. -Präzise Steuerung: Ausgestattet mit einem Siemens-Automatisierungssystem für präzise und gleichbleibende Prozesskontrolle. Unabhängige Stationen: Mehrere Bearbeitungsstationen ermöglichen vielseitige Prozesse, sodass verschiedene Arbeitsschritte gleichzeitig oder nacheinander ausgeführt werden können. Tischoptionen: Verfügbare Arbeitstischgrößen: 650 mm, 1000 mm oder 1300 mm, um spezifische Produktionsanforderungen zu erfüllen. Tischarten: Flexible Konfigurationen wie Magnet-, Vakuum- oder Magnet-Vakuum-Tische gewährleisten eine sichere Fixierung verschiedener Materialien und Werkstückgrößen. Plasma- und Sauerstofftechnologie: Setzt moderne Plasma- und Sauerstofftechnik ein, um starke Grate und Schneidreste wirkungsvoll zu entfernen und so saubere sowie glatte Oberflächen zu erzielen. Oberflächenreinigung: Entfernt effizient Oberflächenverunreinigungen wie Rost, Oxidschichten und Zunder – optimal zur Vorbereitung für die Weiterverarbeitung. Kantenverrundung für Beschichtungen: Perfekte Vorbereitung der Teile für Lackier- und Beschichtungsprozesse durch eine gleichmäßige und fehlerfreie Oberfläche. Einsatzbereiche: Ideal für Stahl-Service-Center, Energie, Bergbau, Bauwesen und Automobilindustrie – speziell zugeschnittene Lösungen für Schwerlast-Anwendungen. Gleichmäßige Resultate: Sechs Lamellenräder sorgen für konsistente, gleichmäßig abgerundete Kanten an jedem Teil. Pneumatisches Oszillationssystem: Bjdpehq A T Ujfx Abfelc Verlängert die Standzeit der Schleifbänder, indem es den Verschleiß reduziert und eine dauerhaft gleichbleibende Leistung sicherstellt.

Sąlyga: naudotas, Gamybos metai: 2021, Darbo sritis 3000 x 1500 mm Bodpfxjxr U U Re Abfjlc Maks. lazerio galia 4 kW (TruDisk 4001) Didžiausias lakšto storis 25/20 mm (st. 37/nerūdijantis) Integruota kamera procesų stebėjimui (su monitoriaus sąsaja) Valdymas: Siemens Sinumerik 840 D SL su 18” lietiminiu ekranu Automatinis greičio reguliavimas Programuojamas automatinis mašinos išjungimas Varinio pjovimo paketas Žalvario pjovimo paketas Įranga: Automatinis palečių keitiklis Įsigijimo kaina 2021 m.: 2 700 000 DKK be PVM.