Plati juostinis šlifuoklis

SCM dmc sd 60

Sąlyga: paruoštas naudoti (naudotas), Gamybos metai: 2018, Pagrindinis variklis Veleno variklio galia: 11 kW Ši SCM DMC sd60 juostinė šlifuoklė pagaminta 2018 m. Darbinis plotis – 1 100 mm, apdirbamų ruošinių aukštis – nuo 4 iki 170 mm. Įrengta 15 kW pagrindiniu varikliu, darbinio judėjimo greitis 4,5/9 m/min. Papildomos ypatybės: guma dengtas kalibravimo volas, šlifavimo volas, kietas šlifavimo padas ir elektroninis valdymas tiksliam darbui. Apsvarstykite galimybę įsigyti šią SCM DMC sd60 juostinę šlifuoklę. Dėl daugiau informacijos susisiekite su mumis. Lodpfxex Nr Sds Abkjhr Pritaikymo sritys Šlifavimas

Sąlyga: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2021, Funkcionalumas: visiškai funkcionalus, šlifavimo plotis: 1 350 mm, SCM Wide Belt Calibration and Fine Finishing Machine Model dmc sd 60 RCS 135 Technical Data: Working width 1,350 mm Min./max. working height 4-170 mm Abrasive belt width 1,370 mm Abrasive belt length 2,150 mm Main motor power 11 (15) kW (HP) Lhjdpjtwqn Ssfx Abkor Gear motor 0.45/0.8 (0.6/1.1) kW (HP) Feed speed 4.5/9 m/min Standard Equipment: - R140/85 rubber-coated calibration roller, diameter 140 mm, 85 Shore - 1st position - R160/45 rubber-coated sanding roller, diameter 160 mm, 45 Shore - 2nd position - Hard sanding pad with manual adjustment of working height - Motor power, 1st unit: 11 kW (15 HP) - Electronic ammeter for the main motor to display current consumption - Electronic display for working height - Electronically controlled abrasive belt oscillation - Rubber pressure rollers - Kickback protection at the infeed before the first unit - Rubber feed belt, 60 Shore - Roller table with two rollers at the infeed and outfeed of the worktable - Feed belt with two speeds: 4.5 / 9 m/min with gear motor - Automatic belt centering Includes the following special accessories: 1x "B" version for RCS with: pneumatic activation/deactivation of the roller at 1st unit “R” + pneumatic activation/deactivation of the roller at 2nd unit “CS” + “MESAR” elastic segmented sanding pad + pneumatic activation/deactivation of the sanding pad unit + electronic programming unit “LOGIC 50” + electronic height adjustment 1x CE safety regulations 1x roller table at infeed and outfeed for long workpieces, equipped with 5 non-driven rollers 1x "RA" diagonal-ribbed steel contact roller, 1st unit 1x main motor 18.5 kW (25 HP)

Sąlyga: naujas, - NEW - GENERAL FEATURES: Machine frame and work table * Steel structure with electric control cabinet at the front of the machine * Introduction of sanding belts from the left side of the machine * Motorized table height adjustment * Main motor integrated into the machine frame Electrical equipment * Electromechanical control panel on the left front side of the machine * Automatic star-delta starter for the main motor * Motor protection switches for the motors * Motors with protection class IP 54 Emergency and safety devices * Safety microswitch for thickness overrun * Automatic brake for immediate stopping of the aggregates * Emergency stop bar at the workpiece infeed * Mushroom switch at the workpiece infeed and outfeed Lhodpfx Asvwfrnebker * Lockable main switch * Automatic emergency machine shutdown in cases of: - sanding belt breakage - sanding belt not tensioned - protection against lateral wandering of sanding belt - lack of compressed air - main motor overload Note: The standard version with 400 Volts 50 Hz requires a three-phase power supply + neutral conductor + earth conductor. If the 400 Volt power supply is without a neutral conductor, a single-phase transformer from the price list must be ordered as well. The same transformer must also be ordered with a machine having a voltage higher than 400 Volts, regardless of whether a neutral conductor is present or not. Machines with 220 or 230 Volts (50 or 60 Hz) are available at an extra cost (see price list). BASE MACHINE STANDARD EQUIPMENT - R140/85 rubber-coated calibrating roller, diameter 140 mm 85 Sh - 1st position - R160/45 rubber-coated sanding roller, diameter 160 mm 45 Sh - 2nd position - Hard sanding pad with manual working height adjustment - Main motor 11 kW (15 HP) - Electronic ammeter for main motor to indicate current consumption - Electronic display of working height - Electronically controlled sanding belt oscillation - Rubber pressure rollers - Kickback protection at the infeed before the first aggregate - Rubber feed belt 60 Sh - Roller table with two rollers at infeed and outfeed of worktable - Belt feed with two speeds 4.5 / 9 m/min with gear motor - Automatic belt centering Working width mm: 1,100 Min./max. working height mm: 4 – 170 Sanding belt width mm: 1,115 Sanding belt length mm: 2,150 Main motor power kW (HP): 11 (15) Gear motor kW (HP): 0.45/0.8 (0.6/1.1) Feed speed m/min: 4.5/9 Comprises: 10.90.87 European safety regulations (mark C.E.) 93.07.31 Volt 400 EU 93.12.01 Frequency 50 Hz 44.44.19 Version "B" for RCS 33.31.50 Roller table at infeed and outfeed for long workpieces 62.44.50 10" operating panel with "eye-S" software integration 31.21.60 "RA" helical-grooved steel contact roller - 1st aggregate 97.50.71 Main motor 15 kW (20 HP)