Kdr pirkti naudotą (159)

Sąlyga: naudotas, Gamybos metai: 2023, bendras ilgis: 7 090 mm, Working height: 16.21 m Ground clearance (access): 0.38 m Platform height: 14.21 m Maximum lateral outreach: 8.52 m Articulation joint clearance / overhang: 7.59 m Basket arm swivel angle (up / down): +66.50° / -65.80° Platform basket load capacity: 408 kg Upper carriage rotation: 350° Platform basket rotation (right / left): 90° / 90° Kjdpfx Abexd Elwskofa Permitted number of persons (indoor / outdoor): 3 / 3 Platform weight: 7,500 kg Platform basket dimensions (length x width): 2.30 m x 0.90 m Overall length: 7.09 m Overall width: 2.45 m Overall height: 2.47 m Transport length (retracted): 4.89 m Transport height (retracted): 2.94 m Counterweight offset (upper carriage at 90°): 0.15 m Outer turning radius: 4.09 m Ground clearance at wheelbase center: 0.40 m Wheelbase: 2.20 m Travel speed – transport mode: 5 km/h Travel speed – work mode: 1 km/h Gradeability: 45% Permitted inclination in working mode: 5° Tyres: Foam-filled Tyre size: 914 x 370 mm Drive wheels (front / rear): 2 / 2 Steering wheels (front / rear): 2 / 2 Braked wheels / wheels: 0 / 2 Manufacturer / engine model: Kubota D1105-E4B Engine emission standard: Stage V Rated engine power / output: 24.80 Hp / 18.50 kW Ground pressure: 11.50 dan/cm² Hydraulic pressure: 340 bar Hydraulic tank capacity: 53 l Fuel tank capacity: 51 l Ambient noise (LwA): < 105 dB Hand/arm vibration exposure: < 0.50 m/s² Daily fuel consumption: 7 l

Gamybos metai: 2020, Sąlyga: visiškai atnaujintas (naudotas), For extraction diameters from 120 to 700 mm. Please inform us of your required air volume flow rate, and we will select the appropriate cyclone for you. Various configurations available: - Legs made from painted square steel profiles - Rotary airlock valve and transition piece with inspection hatch - Inlet box with backdraft damper - Tangential outlet with or without pressure relief area - Square outlet with or without pressure relief area - Sound insulation Kfsdpfxoftb Ebe Abkoa Of course, you can also obtain all necessary accessories from us, such as fans, extraction pipes, deflector hoods, etc. Operating principle: Contaminated air is introduced tangentially into the upper cylindrical section, causing the air to spin. Under the influence of centrifugal force, the material is pushed towards the perimeter of the cyclone and discharged through the hole at the bottom. The cleaned air exits the cyclone via the centrally positioned outlet pipe at the top. The separation efficiency increases with the feed velocity; however, pressure loss and thus energy consumption also increase. Therefore, it is important to find an optimal balance. We have developed a range of cyclones optimized for filtering large material volumes. They are therefore ideally suited for the wood, paper, recycling, grain, and feed industries. Below, you can select the cyclone with the correct size based on the air quantity and a typical pressure drop in the range of 1000 Pa. Operating pressure +/- 5000 Pa.

Sąlyga: beveik kaip naujas (naudotas), Gamybos metai: 2016, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 765, aukščio reguliavimo tipas: hidraulinis, įvesties srovės tipas: trifazis, aplinkos temperatūra (min.): 12 °C, aplinkos temperatūra (maks.): 40 °C, bendras aukštis: 1 635 mm, bendras svoris: 3 900 kg, galia: 110 kW (149,56 AG), įėjimo įtampa: 400 V, Įranga: dokumentacija / vadovas, Die Amandus Kahl 38-780 Pelletpresse wurde 2016 beim Hersteller produziert und erworben. Sie ist für die Herstellung von Pellets mit 6 mm Durchmesser aus Holzabfällen und anderen pflanzlichen Reststoffen konzipiert. Die Anlage wurde in einer Linie für die Demonstrationsproduktion von Holzpellets installiert. Der Granulator wird als Komplettsatz geliefert, bestehend aus: 1. Amandus Kahl 38-780 Pelletpresse mit automatischem System zur Granulatdichte-Regulierung Betriebsbedingungen: Umgebungstemperatur der Presse: 0 bis +40 °C Im Lieferumfang enthalten: - Zerlegbares Gehäuse aus Guss mit Kühlrippen im Getriebebereich - Staubkappe und Einlaufhaube mit Produktverteiler - Hauptwelle mit axialem und radialem Lagerbock - Presskopf mit Walzen aus flammgehärtetem Stahl - Distanzringe - Austragseinrichtung - Austragsförderschnecke im Ölbad betrieben, Förderschneckenrad aus Spezialbronze, gehärtete Förderschneckenwelle - Keilriemen-Scheibenlüfter - Ölpumpe zur Schmierung der Hauptlager, mit Ölfilter, Druckschalter und Thermometer - Werkzeugkasten mit Spezialwerkzeugen Antriebsaggregat – Granulator bestehend aus: - Drehstrommotor auf Füßen, (IE2), Leistung: 110 kW - Spannreifen - Keilriemenscheibe - Keilriemen - Keilriemenschutz - Ausführung als Stahlkonstruktion mit Seitenwänden aus Gittern und speziellen Prallblechen, für die erforderliche Kühlung der Presse Zentralschmierung der Walzen zur Schmierung der Walzenlager während des Pressbetriebs bestehend aus: - Schmierstoffverteiler mit Rohrleitungssystem und Kupplungen - Schlauch mit Zentralschmiernippel - Fettpumpe mit Behälter, Motorpumpe, Sicherheitsventile - Steuereinheit und Kontrolleinrichtung Hydrauliksystem der Presse zur stufenlosen Einstellung des Walzspalts sowie zum schnellen und einfachen Lösen des Presskopfs Betriebstemperatur: 12 bis +40 °C - Hydraulikaggregat bestehend aus: - Hydraulikmutter mit korrosionsgeschützten Dichtflächen, Dichtungsringen in Nuten, Planscharnier und Distanzringen - Hydraulikmotorpumpe mit Schaltschrank zur Einstellung der Hydraulikpumpe und Hydraulikventile mit Ein-/Ausschalter, Steuerung für Hochdruckschlauch, Kupplungen und Druckbegrenzungsventile 2. Mischschnecke M 315 zur Mischung und Vorbereitung der Rohstoffe, bestehend aus: Kodpfsxcv Dzex Abkjfa - Rohrgehäuse mit Wartungsöffnung, inklusive Ein- und Auslauf - Schneckenwelle mit progressiver Förder- und Mischwendel - Stirnlagerdeckel mit Wälzlagern und Dichtungen - Flüssigkeitssprühvorrichtung mit doppelseitiger Düse - Gelenk für Drehung der Schnecke von der Presse weg - Aufgesetztes Getriebe, Leistung: 5,5 kW 3. Wasserdosiersystem, bestehend aus: Typ WD GLI 15 – Durchsatz: 10–100 l/h bei 36 bar Rückdruck Enthalten: - Schmutzfänger - Magnetventil - Reduzierer aus Zinn-Zink-Bronze mit Manometer - Flexibler Metallschlauch - Induktiver Durchflussmesser 4. Flachmatrize Werkstoff: AKN 13 Lochung: 6 mm 5. Flachmatrize für Weichholz Werkstoff: AKN 13 Lochung: 6 mm 6. Bedienungsanleitung, weitere Dokumentation ZUSÄTZLICH ZU VERKAUFEN: KOMPLETTE PELLETPRODUKTIONSLINIE Eine voll funktionsfähige Pelletproduktionslinie steht zum Verkauf. Diese schlüsselfertige Lösung ist sofort einsatzbereit. Wichtige Spezifikationen: Leistung: 160 t/Monat Pellettdichte: 1,24 kg/dm³ Installierte Leistung: 352 kW Heizgenerator: 1 MW (thermische Energie) Endprodukt: Hochwertige 6-mm-Brennstoffpellets

Sąlyga: naujas, Sheet width 4100 mm Sheet thickness 10.0 mm Sheet thickness for stainless steel 6.0 mm Hold-downs 28 pieces Strokes 18 strokes/min Oil capacity 260 ltr. Cutting angle 0.5 - 2° Control CYBELEC Cybtouch Motor power 22.0 kW Backgauge - adjustable 1000 mm Dimensions (L-W-H) 6100 x 2580 x 2460 mm Weight 15,100 kg The manufacturer ERMAK offers with its hydraulically guided guillotine shear model series HVR a robust and durable machine for economical sheet metal processing. This compact all-rounder allows you to increase your productivity. The hydraulic guillotine shear model HVR supports you with precise, fast, and cost-efficient cutting in your daily workflow. The use of hydraulic hold-downs to secure the sheet and the support table with integrated ball rollers ensures ergonomic and efficient cutting for the operator. The CNC control enables the use of various types of sheet metal, which are already stored in the material library. After selecting the maximum thickness and material type, the optimal blade clearance and cutting angle are set automatically via the CNC control (electro-hydraulic adjustment), but can also be manually adjusted. The position and retract function of the motorized backgauge can be conveniently set via the touchscreen. Additionally, the control offers memory for cutting programs with cutting sequences. ----- Robust electro-hydraulic CNC guillotine shear, guided by guideways * including CYBELEC CNC touch screen controller * including CNC electro-hydraulic blade clearance adjustment * including CNC electro-hydraulic cutting angle adjustment ----- Equipment/features: - CNC electro-hydraulic guillotine shear, guideway/slideway guided - including CYBELEC CNC touch screen controller, model "CybTouch 8" - Some functions of the CNC control: * Backgauge preset (X axis) * Blade clearance adjustment * Piece counter * Cutting length limitation * Material selection including sheet thickness * Cut line illumination (cutting to scribed line) ...and many more - Motorized backgauge, travel 5.0 - 1,000 mm (X axis) * On ball screw spindle * Automatic swing-up at maximum travel for longer cuts * Includes selectable "Swing-Away" retract function * Positioning accuracy 0.1 mm * Approx. traverse speed 80 mm/sec - 1x side gauge with T-slot and mm scale - 2x front support arms with T-slot and mm scale - Ball rollers in the front support table - Folding finger guard with safety switch * Finger guard with viewing windows for cutting to scribed line - Cut line lighting with shadow projection - BOSCH/HOERBIGER hydraulic system - SIEMENS electrical system Kodpjxabwuofx Abkofa - Light curtain at the rear of the machine (safety device) - Mobile foot switch - CE marking/declaration of conformity - Operating manual + wiring diagram + hydraulic diagram Including special equipment: - Pneumatic sheet metal support device for thin sheet cutting * Monoblock design

Sąlyga: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2019, mašinos/transporto priemonės numeris: S1AJM3HKC00022X, ID UC04 SAMSUNG ULTRASCHALLGERÄT HS40 FÜR MULTIFUNKTIONS-ULTRASCHALLDIAGNOSTIK; S/N: S1AJM3HKC00022X; Baujahr: Dez. 2019 Hinweis: Das Ultraschallgerät wird mit nur einer CF4-9 Mikro-Convex-Sonde verkauft. Die übrigen Sonden fehlen, können aber je nach Bedarf separat erworben werden. Systemversion: 1.03.01 - Scanmodi: 2D / M / PW / C / PD - Biometry Assist - Aktive Lizenzen: Multivision / DICOM / HQ Vision - Sony UP-X898MD Hybrid-Grafikdrucker 201SAMS0004 Samsung HS40 OB/GYN Ultraschall, betrieben mit CrystalLive Samsung HS40 Abmessungen und Gewicht: • Höhe: 1.354 ~ 1.620 mm (mit Monitor) • Breite: 520 mm • Tiefe: 730 mm • Gewicht mit Monitor: 54 kg (119 lb) Samsung HS40 Technische Daten: • Digitaler Beamformer • Angezeigte Bildtiefe: 0 – 38 cm (sondenabhängig) • Minimale Bildtiefe: 0 – 2 cm (sondenabhängig) • Maximale Bildtiefe: 0 – 38 cm (sondenabhängig) • Kontinuierlicher dynamischer Empfangsfokus/kontinuierliche dynamische Empfangsblende • Einstellbarer Dynamikbereich von 30 bis 256 dB Samsung HS40 Elektrische Versorgung: • Spannung: 100 – 240 VAC • Frequenz: 50/60 Hz • Leistungsaufnahme: 800 VA mit Peripheriegeräten Preis: 12.000 € zzgl. MwSt., FCA: Bukarest/Rumänien Kfjdpfxjg Twgme Abkoa Irrtum, Änderungen und Zwischenverkauf vorbehalten. / Subject to errors, changes and prior sale. / Ne rezervăm dreptul la greșeli, modificări și vânzare prealabila. Wir sprechen Deutsch. /We speak English. /Beszélünk magyarul. /Nous parlons français /Vorbim romana.

Sąlyga: geras (naudotas), Pressemaschine, Hydraulikpresse, Gebrauchtmaschine Hersteller: SEJFO Modell: 7051-3 Gesamtabmessungen: 800 x 1400 x 2480 mm Gewicht: 996 kg Hub: 300 mm Maximaler Hydraulikdruck: 140 Bar Baujahr: 1997 Hydraulikaggregat: 380 V; 50 Hz Kodot A U Irjpfx Abkefa

Sąlyga: naujas, Gamybos metai: 2024, bendras ilgis: 7 060 mm, · Working height: 16.21 m · Ground clearance (access): 0.38 m · Platform height: 14.21 m · Maximum lateral outreach: 8.52 m · Jib articulation / articulation point: 7.59 m · Basket arm rotation angle (up / down): +66.50° / -65.80° · Platform load capacity Q: 408 kg · Upper structure rotation: 350° · Platform rotation (right / left): 90° / 90° · Number of persons (indoor / outdoor): 3 / 3 · Inside turning radius: 1.28 m · Outside turning radius: 4.09 m · Driving speed - transport mode: 5 km/h · Driving speed - working mode: 1 km/h · Gradeability: 45% · Permissible tilt in working mode: 5° · Tyres: foam-filled · Tyre size: 914 x 370 mm · Drive wheels (front / rear): 2 / 2 · Steering wheels (front / rear): 2 / 2 · Braked wheels / wheels: 0 / 2 · Manufacturer / engine model: Kubota - D1105-E4B · Emission standard: Stage V Ksdpfxexd Elds Abkefa · Rated engine output / power: 24.80 Hp / 18.50 kW · Ground pressure: 11.50 dan/cm2 · Hydraulic pressure: 340 bar · Hydraulic tank capacity: 53 l · Fuel tank capacity: 51 l · External noise level (LwA): < 105 dB · Hand/arm vibration exposure: < 0.50 m/s² · Daily consumption: 7 l · NOX emissions: 5.80 kg

Gamybos metai: 2024, Sąlyga: naujas, ‼️SPECIAL OFFER‼️AVAILABLE FROM STOCK IN HEILBRONN! Only while supplies last! ‼️IMMEDIATE DELIVERY‼️IN STOCK‼️ Powerful and robust machine at an affordable price from Josan & Söhne Small Alligator Shear: ➡️3 kW motor ➡️7 to 8 cuts per minute ➡️Dimensions: 1100 x 980 x 800 mm ➡️Weight: approx. 275 kg ➡️Jaw opening: 15 cm ➡️Blades can be reversed once dull for extended service life ➡️UVV (German accident prevention regulations) executed by a German company Net price: €3,999.00 +19% VAT: €759.81 Gross price: €4,758.81 Kfsdpfx Ajp E Ehqjbkea Large Alligator Shear: ➡️7.5 kW motor ➡️Jaw opening: 30 cm ➡️7 to 8 cuts per minute ➡️Dimensions: 249 x 109 x 174 cm ➡️Weight: approx. 1,500 kg ➡️Blades can be reversed once dull for extended service life ➡️630 kN cutting force ➡️Hydraulic pressure: 21 MPa ➡️UVV (German accident prevention regulations) executed by a German company PRICE ON REQUEST Photos/specifications may vary. Subject to errors and changes.

Sąlyga: naujas, Table size: 1000 x 1000 mm Table load capacity: 4000 kg Swivel range: 105 degrees Rotational speed: 0.15 – 1.5 rpm Height adjustment: 1010 – 1836 mm Hollow spindle diameter: mm Welding current: 1000 Amps Torque at faceplate: 8000 Nm Total power requirement: 6.0 kW Required space: approx. m Features: • Made in the EU • Self-locking gearbox – prevents overtravel or backdriving under eccentric load • Hydraulic height adjustment allows nearly unlimited positioning • Electronic quality components from Schneider/Siemens/Delta • Frequency-controlled, stepless speed of turntable Kodpfx Abovn Uztskefa • High stability due to robust, compact construction • CE certified • Excellent price-performance ratio • Standard version comes with remote control and dual foot pedal • 3-year warranty (see warranty conditions) • Hydraulically height adjustable with safety locking system (fall protection)

Sąlyga: naujas, Sheet width: 3100 mm Sheet thickness: 13.0 mm Sheet thickness (stainless steel): 8.0 mm Hold-down devices: 14 units Strokes: 11 - 20 strokes/min Oil capacity: 310 liters Cutting angle: 0.05 - 2.0° Throat depth: 350 mm Table height: 900 mm Total connected load: 22.0 kW Machine weight: approx. 13,300 kg Dimensions (LxWxH): 5,110 x 2,570 x 2,400 mm The manufacturer ERMAK offers you, with its hydraulically guided guillotine shear series HVR, a robust and durable machine for efficient sheet metal processing. This compact all-round machine helps you increase productivity. The hydraulic guillotine shear model HVR supports you with precise, fast, and cost-effective cutting in your daily workflow. The use of hydraulic hold-downs to secure the sheet, along with a support table equipped with integrated ball rollers, ensures ergonomic and efficient cutting for your operator. The CNC control system enables the use of various sheet materials already stored in the material library. Once the maximum thickness and material type are selected, the optimal cutting clearance and angle are automatically adjusted electro-hydraulically via CNC control, but can also be set manually. The position and retract function of the motorized backgauge can be easily controlled via touchscreen. Additionally, the system offers storage for cutting programs with cut sequences. ----- Robust electro-hydraulic CNC guillotine shear with sliding guide * Inclusive of CYBELEC CNC touchscreen control * Inclusive of CNC electro-hydraulic cutting gap adjustment Kedpfsxabikjx Abkjfa * Inclusive of CNC electro-hydraulic cutting angle adjustment ----- Equipment: - CNC electro-hydraulic guillotine shear, "sliding guided" - Inclusive of CYBELEC CNC touchscreen controller, model "CybTouch 8" - Selected functions of the CNC control: * Backgauge preset – X-axis * Cutting gap adjustment * Piece counter * Cutting length limitation * Material selection, including sheet thickness * Cutting line illumination (cutting on scribed line), and many more - Motorized backgauge, travel range = 5.0 – 1,000 mm (X-axis) * On ball screw spindles * Automatically swings up at maximum travel for longer cuts * Retract function selectable ("Swing-Away Function") * Positioning accuracy 0.1 mm * Approx. travel speed 80 mm/sec - 1x side gauge, with T-slot and mm scale - 2x front support arms, with T-slot and mm scale - Ball rollers in front support table - Hinged finger guard with safety switch * Finger guard with viewing windows for scribed line cutting - Cutting line illumination with shadow outline - BOSCH/HOERBIGER hydraulic unit - SIEMENS electrical cabinet - Light curtain at the rear of the machine (safety feature) - Mobile foot switch - CE marking / Declaration of Conformity - Operating manual + wiring diagram + hydraulic diagram

Gamybos metai: 2005, Sąlyga: labai geros būklės (naudotas), Funkcionalumas: visiškai funkcionalus, tuščias svoris: 63 kg, didžiausias leistinas svoris: 300 kg, mašinos/transporto priemonės numeris: 2441, Mobile tank, volledig gemaakt van roestvrij staal, merk Eurocont, bouwjaar 2005, technisch en optisch in onberispelijke staat, pakkingen in uitstekende staat, Serie: 2441, gewicht 63 kg, toegestane werkdruk: 1 bar; geteste druk 1,7 bar; toegestane negatieve werkdruk: -0,15 bar, maximaal toegestane bedrijfstemperatuur: +130°C. Deze tank kan onder druk werken indien een manometer wordt geïnstalleerd. Mobiele RVS-tank voor diverse voedingsmiddelen en non-food vloeistoffen. Inhoud 300 liter, diameter 800 mm, hoogte 1.140 mm. De tank staat op vier zwenkwielen met remmen. Hij beschikt over 3 bovenzijde vulaansluitingen: 100 DN met afsluiter, 50 DN en 20 DN aansluiting, en een onderste DN 100 afvoer-/leegaansluiting met afsluiter en schroefdop. Kfodetctmxjpfx Abkea Verkoopprijs: € 2.550 + btw, onderhandelbaar, FCA Oradea, Roemenië Irrtum, Anderungen und Zwischenverkauf vorbehalten / Onder voorbehoud van fouten, wijzigingen en tussentijdse verkoop / We behouden ons het recht voor op fouten, wijzigingen en tussentijdse verkoop. We spreken Engels. / Wir sprechen Deutsch. / Wij spreken Hongaars. / Nous parlons français / Wij spreken Roemeens.

Sąlyga: naudotas, Air duct, air control damper, ventilation system, filtration unit, chip extraction, dust extraction, extraction system, ventilation ducts and fittings, louver damper, backdraft damper, louvered ventilator Kodpfx Absharupeksfa - Air control damper: louvered ventilator, louver damper - Air control dampers: mechanically adjustable, non-motorized - Opening with 6 louvers: 1170 x 510 mm - Overall dimensions: 1325/560/H115 mm - Weight: 21 kg

Sąlyga: naujas, Gamybos metai: 2023, keliamoji galia: 3 000 kg, kėlimo aukštis: 6 900 mm, bendras ilgis: 5 920 mm, ・Max. lifting capacity: 3,000 kg ・Max. lift height: 6.90 m ・Maximum lateral reach: 4 m ・Tilting angle: 11° ・Dump angle: 116° ・Turning radius (over wheels): 3.33 m ・Transmission type: hydrostatic ・Standard tires: ALLIANCE 380/75 R20 148A8 A580 ・Number of gears (forward / reverse): 2 / 2 Kedpoxd Ektsfx Abkofa ・Max. travel speed: 24.90 km/h ・Parking brake: hydraulic ・Steering wheels (front / rear): 4 / 4 ・Cabin safety certification: ROPS - FOPS Level 2 ・Lifting time: 9.42 s ・Lowering time: 7.53 s ・Telescopic boom extension: 7.43 s ・Telescopic boom retraction: 9.36 s ・Tilting forward: 3.21 s ・Dumping: 2.15 s ・Engine emission standard: Stage V ・Engine model: V3307-CR-TE5B ・Number of cylinders / displacement: 4 - 3,331 cm³ ・Rated engine output / power: 55.92 kW / 54.60 kW ・Max. torque / engine speed: 265 Nm @ 1,400 rpm ・Tractive force: 3,860 daN ・Number of gears (forward / reverse): 2 / 2 ・Max. travel speed: 24.90 km/h ・Parking brake: hydraulic ・Pump type: gear pump ・Hydraulic flow / pressure: 88 l/min / 245 bar ・Engine oil capacity: 11 l ・Hydraulic oil capacity: 115 l ・Fuel tank capacity: 90 l ・Sound level in cab (LpA): 74 dB ・External noise (LwA): 103 dB ・Hand/arm vibration exposure: < 2.50 m/s² ・Steering wheels (front / rear): 4 / 4

Sąlyga: naujas, Table diameter: 1300 mm Table load capacity: 3000 kg Swivel range: 0 - 130 degrees Ksdpfx Asfv Ayysbkjfa Rotational speed: 0.05 - 0.5 rpm Height adjustment: 1200 - 1800 mm Torque at faceplate: 6000 Nm Motor power: 1.1 / 1.1 kW Welding current: 700 Amps - Manual height adjustment. - Self-locking gearbox for minimal overrun and backdriving under eccentric loads. - Electronic components from Schneider, Siemens, and Delta. - Frequency-controlled, infinitely variable rotary table speed. - High stability due to robust construction. - CE certificate. The D-HBE series comes standard with a pendant cable remote control and a foot switch. Welding current transmission up to max. 500 Amps.

Sąlyga: naujas, Sheet width: 3100 mm Sheet thickness: 6.0 mm Frame width: 3,100 mm Hold-downs: 14 units Strokes: 16 - 24 strokes/min Oil capacity: 150 ltr. Cutting angle: 0.5 - 1.5° Sheet thickness (stainless steel): 4.0 mm Frame throat: 350 mm Motor power: 11.0 kW Machine weight: approx. 7,060 kg Dimensions (L-W-H): 4.1 x 2.2 x 2.19 m The manufacturer ERMAK offers, with its hydraulically-guided swing beam shear of the HVR series, a robust and durable machine for the economical processing of sheet metal. This compact all-round machine allows you to increase your productivity. The hydraulic guillotine shear, model HVR, supports you with precise, fast, and cost-efficient cuts in your daily workflow. By utilizing hydraulic hold-downs to secure the sheet and a support table with integrated ball rollers, ergonomic and efficient operation for your operator is ensured. The CNC control enables the selection of various sheet types, which are already available in the material library. After choosing the maximum thickness and material type, the optimal blade gap and cutting angle are automatically set electro-hydraulically via the CNC system but can also be adjusted manually. The position and retract function of the motorized backgauge are easily set via touchscreen. Additionally, the controller provides a memory for cutting programs with cutting sequences. ----- Robust electro-hydraulic CNC swing beam guillotine shear * Includes CYBELEC CNC touchscreen control * Includes CNC electro-hydraulic blade gap adjustment * Includes CNC electro-hydraulic cutting angle adjustment ----- Equipment: - CNC electro-hydraulic swing beam guillotine shear - Including CYBELEC CNC touchscreen controller, model "CybTouch 8" - Selected CNC control functions: * Backgauge preselection - X axis * Blade gap adjustment * Piece counter * Cut length limiter * Material selection, including sheet thickness * Cut line illumination (cutting to scribe line) ...and many more - Motorized backgauge, travel range = 5.0 - 1,000 mm (X axis) * On ball screw spindles * Automatically folds up at maximum travel for longer cuts * Including selectable retract function ("Swing-Away Function") * Positioning accuracy 0.1 mm * Approx. travel speed 80 mm/sec - 1x side stop, with T-slot and mm scale - 2x front support arms, with T-slot and mm scale - Ball rollers in front sheet support table - Hinged finger guard with safety switch Ksdpfx Abexabcqokefa * Finger guard with viewing windows for scribe cutting - Cut line illumination with shadow projection - BOSCH/HOERBIGER hydraulic system - SIEMENS electrical system - Light curtain at rear of machine (safety feature) - Movable foot switch - CE mark / Declaration of Conformity - Operating manual + wiring diagram + hydraulic diagram Including special equipment: - Pneumatic sheet support device for thin sheet cutting

Sąlyga: naudotas, Gamybos metai: 2023, keliamoji galia: 6 000 kg, kėlimo aukštis: 29 900 mm, bendras ilgis: 9 140 mm, · Max. lifting capacity: 6,000 kg · Height: 29.90 m · Maximum lateral outreach: 25.90 m · Tipping angle: 12° · Discharge angle: 110° · Turret rotation (max.): 360° Ksdjxd Eh Eopfx Abkefa · Drive wheels (front/rear): 2 / 2 · Steering types: 2-wheel steering, 4-wheel steering, crab steering mode · Outrigger type: Dual telescopic · Outrigger control: Individual or simultaneous outrigger operation · Manufacturer: Yanmar · Engine emission standard: Stage V / Tier 4 · Engine model: 4TN107FTT-6SMU1 · Rated engine power: 173 HP / 127 kW · Max. torque / Engine speed: 805 Nm @ 1,500 rpm · Number of cylinders / Cylinder displacement: 4 / 4,567 cm³ · Number of batteries / Battery voltage: 2 x 12 V · Battery capacity: 120 Ah · Battery starting current (EN): 850 A · Transmission type: Hydrostatic with Speedshift · Transmission / Number of forward gears / Number of reverse gears: Speedshift / 2 / 2 · Max. travel speed: 40 km/h · Tractive force: 9,200 daN · Parking brake: Automatic negative parking brake · Service brake: Oil-immersed multi-disc brakes on both front and rear axles · Gradeability – loaded / unloaded: 32.40% / 41.40% · Pump type: Variable displacement pump · Hydraulic flow rate: 185 l/min · Hydraulic pressure: 350 bar · Engine oil capacity: 13 l · Hydraulic oil capacity: 300 l · Fuel tank capacity: 320 l · Diesel exhaust aftertreatment (AdBlue®): 24 l · In-cab noise level (LpA): 67 dB · External sound level (LwA): 108 dB · Hand/arm vibration level: < 2.50 m/s² · Steering wheels (front/rear): 2 / 2 · Controls: 2 joysticks · Safety: Cabin approved to ROPS - FOPS Level 2 · Attachments recognition system (E-Reco): Standard

Sąlyga: naujas, Sheet width: 3,100 mm Sheet thickness: 6.0 mm Frame width: 3,100 mm Hold-down clamps: 14 units Stroke rate: 16 - 24 strokes/min Oil capacity: 150 liters Cutting angle: 0.5 - 1.5° Sheet thickness for stainless steel: 4.0 mm Throat depth: 350 mm Motor power: 11.0 kW Machine weight approx. 7,060 kg Dimensions (L x W x H): 4,100 x 2,200 x 2,190 mm ERMAK offers you a robust and durable machine with the HVR model series hydraulic swing beam shear, ideally suited for the efficient processing of sheet metal. This compact all-round machine can help you increase your productivity. The HVR hydraulic guillotine shear supports you with precise, fast, and cost-effective cutting in your daily workflow. The use of hydraulic hold-downs to secure the sheet and the support table with integrated ball transfers ensures ergonomic and efficient cutting for your operator. The CNC controller allows the use of various sheet types stored in the material library. After selecting the maximum thickness & material type, the optimal blade gap & cutting angle are automatically set electro-hydraulically via CNC control, but can also be manually adjusted. The position and retract function of the motorized backgauge can be easily set via touchscreen. Additionally, the controller offers memory for cutting programs with cutting sequences. ----- Robust electro-hydraulic CNC guillotine shear "swing beam guided" * including CYBELEC CNC touchscreen controller * including CNC-controlled electro-hydraulic blade gap adjustment * including CNC-controlled electro-hydraulic cutting angle adjustment ----- Kedpfx Ajxaag Uebkofa Equipment: - CNC electro-hydraulic swing beam shear - Includes CYBELEC CNC touchscreen controller, model "CybTouch 8" - Some CNC controller functions: * Backgauge presetting - X axis * Blade gap adjustment * Piece counter * Cutting length limitation * Material selection, including sheet thickness * Cutting line illumination (cutting to scribe line) ... and many more - Motorized backgauge, travel range = 5.0 - 1,000 mm (X axis) * on ball screw spindles * automatically swings up at maximum travel for longer cuts * selectable retract function ("Swing-Away Function") * positioning accuracy 0.1 mm * approx. traverse speed 80 mm/sec. - 1x side gauge with T-slot and mm scale - 2x front support arms with T-slot and mm scale - Ball rollers in the front support table - Swing-up finger guard with safety switch * Finger guard with viewing windows for scribed-line cutting - Cutting line lighting with shadow line - BOSCH/HOERBIGER hydraulic system - SIEMENS electrical system - Light curtain at the rear of the machine (safety feature) - Movable foot switch - CE mark / Declaration of Conformity - Operating manual + wiring diagram + hydraulic diagram

Sąlyga: naujas, Gamybos metai: 2025, keliamoji galia: 6 000 kg, kėlimo aukštis: 25 900 mm, bendras ilgis: 9 280 mm, Max. lifting capacity: 6,000 kg - Height: 25.90 m - Maximum lateral outreach: 21.70 m - Tilting angle a4: 12° - Dumping angle a5: 110° - Upper carriage rotation: 360° - Tyre size: 445/65 R22.5 - Drive wheels (front/rear): 2 / 2 - Steering mode: 2-wheel steering, 4-wheel steering, crab mode - Support type: double-telescopic - Stabiliser operation: individual or simultaneous controls - Engine manufacturer: Yanmar - Emission standard: Stage V / Tier 4 - Engine model: 4TN107FHT-6SMU1 - Engine rated output / Power (kW): 156 hp / 115 kW - Max. torque / Engine speed (min): 602 Nm @ 1,500 rpm - Number of cylinders – Cylinder displacement: 4 – 4,567 cm³ - Engine cooling system: water cooling Kjdpoxd Ecvjfx Abkofa - Number of batteries / Voltage / Battery capacity: 2 x 12 V / 120 Ah - Battery starting current (EN): 850 A - Transmission type: hydrostatic with Speedshift - Transmission / Number of forward gears / Number of reverse gears: Speedshift 2 / 2 - Max. travel speed: 40 km/h - Drawbar pull: 8,600 daN - Parking brake: Automatic negative parking brake - Service brake: Wet disc brakes on front and rear axles - Gradeability – laden / unladen: 40.40% / 45.50% - Pump type: variable-displacement pump - Hydraulic oil flow: 185 l/min - Hydraulic pressure: 350 bar - Engine oil: 13 l - Hydraulic oil: 260 l - Fuel tank capacity: 270 l - Diesel exhaust after-treatment (AdBlue®): 24 l - Operator cabin noise level (LpA): 68 dB - External sound level (LwA): 108 dB

Sąlyga: naudotas, Gamybos metai: 2023, bendras ilgis: 8 430 mm, · Platform height 18.35 m · Outreach / Articulation joint 8 m · Basket arm rotation angle (up / down) +69° / -66° · Uppercarriage rotation 355° · Work platform rotation (right / left) 90° / 90° · Number of persons (inside / outside) 2 / 2 · Ground clearance at wheelbase centre 0.44 m · Wheelbase 2.40 m · Travel speed - transport mode 4.70 km/h · Travel speed - work mode 0.80 km/h · Gradeability 40% · Permissible inclination in work mode 5° · Drive wheels (front / rear) 2 / 2 · Steering wheels (front / rear) 2 / 2 · Braked wheels / wheels 0 / 2 · 230 V socket · 4-wheel steering with crab steering · 4 simultaneous movements · Audible alarm and warning light (tilt, overload, slope) · CAN bus technology · Rear axle differential lock · Electric emergency pump · Engine with DPF · Galvanised basket 2,100 mm · Oscillating front axle · Proportional control · Stop & Go · Stepwise speed regulation · Dead-man pedal · Front axle with slip limitation · Large colour display at ground control station · Inside turning radius 1.26 m · Outside turning radius 3.90 m · Engine emission standard Stage V Kfsdpfx Absxd Eb Eeksa · Nominal combustion engine power / output (kW) 34 hp / 25.50 kW · Ground pressure 20.65 daN/cm² · Hydraulic pressure 340 bar · Hydraulic tank capacity 80 l · Fuel tank capacity 78.50 l · Harmful NOX emissions 2.61 kg

Sąlyga: naudotas, Gamybos metai: 2024, bendras ilgis: 7 090 mm, · Working height: 16.21 m · Ground clearance (access): 0.38 m · Platform height: 14.21 m · Maximum lateral outreach: 8.52 m · Jib articulation / articulation point: 7.59 m · Basket arm rotation angle (up / down): +66.50° / -65.80° · Platform load capacity Q: 408 kg · Upper structure rotation: 350° · Platform rotation (right / left): 90° / 90° · Number of persons (indoor / outdoor): 3 / 3 · Inside turning radius: 1.28 m · Outside turning radius: 4.09 m · Driving speed - transport mode: 5 km/h · Driving speed - working mode: 1 km/h · Gradeability: 45% · Permissible tilt in working mode: 5° Kedpfx Asxd Ea Ijbksfa · Tyres: foam-filled · Tyre size: 914 x 370 mm · Drive wheels (front / rear): 2 / 2 · Steering wheels (front / rear): 2 / 2 · Braked wheels / wheels: 0 / 2 · Manufacturer / engine model: Kubota - D1105-E4B · Emission standard: Stage V · Rated engine output / power: 24.80 Hp / 18.50 kW · Ground pressure: 11.50 dan/cm2 · Hydraulic pressure: 340 bar · Hydraulic tank capacity: 53 l · Fuel tank capacity: 51 l · External noise level (LwA): < 105 dB · Hand/arm vibration exposure: < 0.50 m/s² · Daily consumption: 7 l · NOX emissions: 5.80 kg

Sąlyga: naudotas, Gamybos metai: 2023, bendras ilgis: 6 100 mm, - Working height: 14.60 m - Platform height: 12.60 m - Maximum outreach: 7.13 m - Up-and-over clearance / Articulation point: 7.07 m - Vertical rotating jib (up / down): +65° / -65° - Platform basket capacity: 220 kg - Upper structure rotation: 355° - Basket rotation (right / left): 66° / 59° - Permitted number of persons (indoors / outdoors): 2 / 2 - External turning radius: 3.96 m - Travel speed - transport mode: 5 km/h - Travel speed - work mode: 0.60 km/h - Gradeability: 22% - Permissible tilt in work mode: 3° - Drive wheels (front / rear): 0 / 2 - Steerable wheels (front / rear): 2 / 0 - Braked wheels / axles: 0 / 2 - Rated electric motor output: 2 x 3 kW - Lift motor output: 3.70 kW - Nominal battery voltage / battery capacity: 48 V / 240 Ah - Battery energy: 11 kWh - Integrated charger / charger: 48 V / 30 A - Number of cycles with standard battery (HIRD): 46 - Ground pressure: 13.50 dan/cm² - Hydraulic flow rate – hydraulic pressure: 180 bar - Hydraulic tank capacity: 15 l - Ambient noise level (LwA): < 70 dB - Hand/arm vibration exposure: < 0.52 m/s² Kfodpfxoxd Eabj Abkja

Sąlyga: naujas, Gamybos metai: 2024, bendras ilgis: 7 090 mm, - Working height: 16.21 m - Ground clearance (access): 0.38 m - Platform height: 14.21 m - Maximum lateral outreach: 8.52 m - Articulation overhang / knuckle point: 7.59 m - Basket jib rotation angle (up / down): +66.50° / -65.80° - Platform basket load capacity: 408 kg Ksdpfexd D T Tex Abkjfa - Upper carriage rotation: 350° - Platform basket rotation (right / left): 90° / 90° - Number of persons (indoor / outdoor): 3 / 3 - Inside turning radius: 1.28 m - Outside turning radius: 4.09 m - Driving speed – transport mode: 5 km/h - Driving speed – working mode: 1 km/h - Gradeability: 45% - Permissible tilt in working mode: 5° - Tyres: foam-filled - Drive wheels (front / rear): 2 / 2 - Steering wheels (front / rear): 2 / 2 - Braked wheels / total wheels: 0 / 2 - Manufacturer / engine model: Kubota – D1105-E4B - Engine standard: Stage V - Rated engine output / power: 24.80 Hp / 18.50 kW - Ground pressure: 11.50 daN/cm² - Hydraulic pressure: 340 bar - Hydraulic tank capacity: 53 l - Fuel tank capacity: 51 l - Ambient noise level (LwA): < 105 dB - Hand/arm vibration exposure: < 0.50 m/s² - Daily consumption: 7 l - NOX emission: 5.80 kg

Sąlyga: naujas, Gamybos metai: 2025, keliamoji galia: 2 500 kg, kėlimo aukštis: 5 850 mm, bendras ilgis: 5 130 mm, Maximum lateral reach: 3.40 m • Breakout force with bucket: 3427 daN • Dumping angle: 12° • Tip-out angle: 117° • Turning radius (over wheels): 3.31 m • Operating weight (with forks): 4800 kg • Tyres: Pneumatic • Lift time: 8 s Kfjdexd D Spopfx Abkea • Lowering time: 5.40 s • Telescope extension: 5.60 s • Telescope retraction: 4.30 s • Tilt-in: 3.50 s • Dump-out: 3.60 s • Number of cylinders / Cylinder capacity: 4 - 3331 cm³ • Rated output combustion engine – Power (kW): 75 Hp / 55.40 kW • Max. torque / Engine speed: 265 Nm @ 1400 rpm • Traction force: 3550 daN • Number of gears (forward / reverse): 2 / 2 • Max. travel speed: 24.90 km/h • Parking brake: Automatic negative parking brake • Service brake: Oil-immersed disc brakes on front axles • Pump type: Gear pump • Hydraulic pressure: 235 bar • Engine oil: 11.20 l • Hydraulic oil: 115 l • Fuel tank capacity: 63 l • In-cab noise level (LpA): 76 dB • Ambient noise (LwA): 104 dB • Hand/arm vibration exposure: < 2.50 m/s² • Steering wheels (front / rear): 2 / 2 • Drive wheels (front / rear): 2 / 2 • Safety / Safety standard cab approval: EN 15000 / Cab ROPS - FOPS Level 1 • Controls: JSM

Sąlyga: naudotas, Gamybos metai: 2023, keliamoji galia: 1 500 kg, kėlimo aukštis: 4 240 mm, bendras ilgis: 4 570 mm, - Max. lifting capacity: 1,500 kg - Lifting height: 4.30 m - Maximum lateral outreach: 2.62 m - Reach at maximum lift height: 1 m - Breakout force with bucket: 1,880 daN - Shipping weight (min. / max.): 2,700 kg / 2,900 kg - Wheelbase: 2.13 m - Overall length to fork carrier (with trailer hitch): 3.47 m - Overall length to fork carrier (without trailer hitch): 3.47 m - Front overhang: 0.77 m - Dump angle: 116° - Tilt angle: 23° - Turning radius (over wheels): 2.62 m - Tyre models: CAMSO - MPT 552 - 10.0/75-15.3 124A8 - Lift time: 8.80 s - Lowering time: 7 s - Telescope extension time: 6.40 s - Telescope retraction time: 4.30 s - Crowd (tilt in): 3.40 s - Dump (tilt out): 2.60 s - Manufacturer: Yanmar - Engine emission standard: Stage V / Tier 4 final - Engine model: 3TNV88C-DMU - Number of cylinders - displacement: 3 - 1,642 cm³ - Nominal engine output / power (kW): 35.10 Hp / 26.20 kW - Max. torque / engine speed: 105 Nm @ 1,950 rpm - Reversible fan: optional - Engine cooling system: 3 coolers (water + hydraulic oil + fuel) - Transmission type: hydrostatic - Number of gears (forward/reverse): 2 / 2 - Max. travel speed (may vary depending on regulations): 25 km/h - Differential lock: locking differential on front and rear axle - Parking brake: automatic negative parking brake - Service brake: hydraulic servo brake - Pump type: gear pump Ksdpfoxd D Scsx Abkjfa - Hydraulic flow - hydraulic pressure: 48 l/min - 235 bar - Flow sharing: standard - Hydraulic oil capacity: 39 l - Fuel tank capacity: 35 l - Internal noise level (LpA) tested according to NF EN 12053: 76 dB - External noise level (LwA): 104 dB - Hand/arm vibration value: < 2.50 m/s² - Safety - cab approval: Cab ROPS - FOPS Level 1 - Controls: JSM

Sąlyga: naujas, Gamybos metai: 2023, keliamoji galia: 3 000 kg, kėlimo aukštis: 8 850 mm, bendras ilgis: 5 900 mm, · Pakreipimo kampas 11° · Išpylimo kampas 116° · Posūkio spindulys (per ratus) 3,35 m · Kėlimo laikas 10,24 s · Nuleidimo laikas 7,95 s · Teleskopo išstūmimo laikas 9,89 s · Teleskopo įtraukimo laikas 9,48 s · Pakreipimo laikas 3,06 s · Iškrovimo laikas 2,44 s · Variklio emisijos standartas Stage V Kfodpfxexd D R Eo Abkja · Cilindrų skaičius / Cilindro darbinis tūris 4 – 3331 cm³ · Nominali vidaus degimo variklio galia – Galia (kW) 75 AG / 54,60 kW · Maks. sukimo momentas / Variklio apsukos 265 Nm @ 1400 aps./min · Traukos jėga 3860 daN · Transmisijos tipas hidrostatinė · Pavarų skaičius (pirmyn/atgal) 2 / 2 · Maks. važiavimo greitis 24,90 km/val. · Rankinis stabdis hidraulinis · Siurblio tipas dantratinis siurblys · Hidraulinės sistemos našumas / slėgis 88 l/min / 245 bar · Variklio alyva 11 l · Hidraulinė alyva 115 l · Kuro bako talpa 90 l · Triukšmo lygis operatoriaus kabinoje (LpA) 74 dB · Aplinkos triukšmo lygis (LwA) 103 dB · Rankų / pirštų vibracijos poveikis < 2,50 m/s² · Vairuojami ratai (priekyje / gale) 2 / 2 · Kabinos saugos sertifikatas Kabina ROPS – FOPS 2 lygis