111A

MACPRESSE EUROPA S.R.L. 111A

Sąlyga: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2005, veikimo valandos: 30 408 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 50 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 250 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 720 mm, balo svoris: 550 kg, bendras svoris: 16 000 kg, alyvos bako talpa: 600 l, paskutinio kapitalinio remonto metai: 2024, Technical Data – Baler: Manufacturer: Presona AB Model: LP 50 EH1 Year of manufacture: 2005 Operating hours: 30,408 hours (as of April) Number of bales pressed: 198,059 units (as of April) Main press ram force: 50 t Specific pressing force: 63 N/cm² Theoretical throughput: 530 m³/hour Throughput under operating conditions: 260 m³/hour Feed chute dimensions: 1,250 x 1,100 mm Press chamber volume: 2.2 m³ Bale dimensions: 1,100 x 720 mm, length variable Drive power: 22 kW Tying: 5-fold vertical, fully automatic Throughput rates at a bulk density of: - 30 kg/m³: 6 to 7 t/hour - 50 kg/m³: 7 to 9 t/hour - 100 kg/m³: 11 to 14 t/hour Bale density (paper/newspapers): 400 to 550 kg/m³ Hydraulic oil tank capacity: 600 L PLC: Telemecanique TSX Micro Operator panel: Schneider Magelis Effective transport dimensions excl. press: 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight (press only): approx. 16 t Condition of the baler: The machine underwent partial refurbishment and general maintenance in our workshop. After completion of the refurbishment, the baler was tested in operational mode and is now available for immediate sale. The following refurbishments were carried out: General work: Dledpfx Adou Thhrjmoa - Machine cleaned, derusted, primed, and partially repainted - Wire entry marks in the press channel openings welded and smoothed Hydraulic unit: - Hydraulic oil tank fully drained, cleaned, and refilled with new oil - Oil and air filters replaced - Leaking oil sight glass on the hydraulic tank replaced - All hydraulic hoses replaced Electrical system: - Program menu language set to English - Two key switches on the operator panel replaced - Control cabinet replaced - Signal lamp on the control cabinet replaced - Flap limit switch replaced - Wirthulator electrics renewed, connected, and tested Press ram: - All four guide rollers on the press ram removed and replaced - Main hydraulic cylinder disassembled, overhauled (cylinder tube honed, complete seal kit replaced), leak test performed - All wear-resistant plastic blocks on the press ram replaced Pre-press flap: - Both bearings on the pre-press shaft replaced - Both hydraulic cylinders disassembled, overhauled (cylinder tubes honed, complete seal kits replaced), leak test performed - Scraper flap on the pre-press replaced Tying unit: - Two complete needles with wire guide pulleys replaced - Needles adjusted and set - All wire guide pulleys in needle heads replaced - Twisting fingers replaced - Two twister shafts replaced - All eight wear plates on the twister unit, under the twisting fingers, replaced Scope of delivery: Only the baler is sold. Documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is complete and available. Inspection by appointment possible. We do not accept liability for the technical data or possible errors.

Sąlyga: geras (naudotas), Gamybos metai: 1985, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 50 t, kamuolio ilgis: 1 000 mm, ryšulio plotis: 750 mm, ryšulio aukštis: 750 750 750 mm, balo svoris: 500 kg, įėjimo įtampa: 400 V, bendras svoris: 7 500 kg, alyvos bako talpa: 500 l, galia: 30 kW (40,79 AG), tuščias svoris: 7 500 kg, įėjimo dažnis: 50 Hz, Manufacturer: Pal Pacomat V Year of manufacture: 1985 Main press force: 50 t Specific pressing force: 5 kg/cm² Feed channel: 1,000 x 720 mm (L x W) Theoretical throughput capacity: 200 m³/h Bale size: 700 x 1,000 mm (W x H), adjustable length Drive motor: 30 kW Bale weight: approx. 500 kg Dedpfsic Rl Dsx Admola Machine weight: approx. 8 t The hydraulic unit is operational; the drive motor is currently disassembled.

Sąlyga: nepatikrintas (naudotas), Hydraulic press for pressing paper and similar materials. The machine was fully operational prior to disassembly. Press dimensions: Dljdpfxoh Nyfye Admsa Length: 4850 mm, width: 1370 mm, height: 3000 mm (reducible to 2300 mm). Weight approx. 3500 - 4000 kg. For further information, please contact: +48 539 660 495.

Sąlyga: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2012, veikimo valandos: 25 895 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 78 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 500 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 600 kg, bendras svoris: 24 000 kg, alyvos bako talpa: 1 000 l, galia: 55 kW (74,78 AG), tūrio srautas: 930 m³/val, Technical Data – Baler: Manufacturer: Presona AB Model: LP 80 VHK 1 Year of Manufacture: 2012 Total Operating Hours (Machine): 25,895 hours (as of July 2025) Dlsdpovwlqqefx Admoa Effective Operating Hours (Pump): 14,135 hours (as of July 2025) Number of Bales Pressed: 235,597 (as of July 2025) Main Pressing Force: 78.5 t Specific Pressing Force: 95 N/cm² Pre-Press Force: 28 t Press Chamber Volume: 2.7 m³ Feed Opening Dimensions: 1,500 x 1,100 mm Theoretical Throughput: 930 m³/hour Throughput Under Operating Conditions: 410 m³/hour Bale Dimensions: 750 x 1,100 mm Drive Power: 55 kW Tying: 5-fold vertical, 3-fold horizontal, fully automatic Throughput at Bulk Density of: - 30 kg/m³: approx. 9 to 12 t/hour (material dependent) - 50 kg/m³: approx. 14 to 17 t/hour (material dependent) - 100 kg/m³: approx. 16 to 25 t/hour (material dependent) Throughput at MSW (Municipal Solid Waste): approx. 20 to 27 t/hour (material dependent) Bale Weights: 450 to 600 kg (depending on material and bale length) Hydraulic Oil Tank Volume: 1,000 L Baler Dimensions (assembled with hopper): 10,985 x 3,750 x 4,310 mm (L x W x H) Transport Dimensions (baler only): 10,985 x 2,300 x 2,900 mm Machine Weight (baler): approx. 24 t Condition of the Baler: The machine was partially overhauled and serviced in our workshop and, upon completion of the work, tested in both manual and automatic modes during operation. The following overhaul work was carried out: - Machine cleaned, partially derusted and partially repainted - Hydraulic oil tank completely drained and cleaned - Oil and air filters replaced, new hydraulic oil filled - Press ram dismantled and cleaned - All four running rollers removed from the press ram and replaced - Twisting wire station with lower wire deflection pulleys cleaned and made operational - Side guides of press ram removed, smoothed, re-installed, and re-adjusted - Main hydraulic cylinder dismantled and disassembled for inspection - Piston rod replaced, cylinder tube honed - Complete seal set replaced, pressure test carried out - Hydraulic hose of main hydraulic cylinder replaced - Vertical and horizontal needle systems for tying dismantled, cleaned, wire deflection pulleys made operational and serviced - Chain cleaned, lubricated, chain tension readjusted - Drillomat cleaned, wire cutters, twisting shafts, and twisting fingers checked, retightened with appropriate torque, and serviced - Door contact switch checked and partly replaced - Emergency stop switch checked - Complete electrical wiring checked and partly renewed - Bearings of the wire guide rollers under the press replaced - New safety guards for vertical and horizontal tying manufactured and installed - Machine inspected, general maintenance performed, and baler tested in manual and automatic mode Scope of Delivery: Only the baler is being sold. Remarks: Full documentation is available (operating manual, CE declaration, electrical/hydraulic circuit diagram). Inspection by appointment is possible. No liability is assumed for technical specifications or possible errors.

Gamybos metai: 2006, Sąlyga: beveik kaip naujas (naudotas),

Sąlyga: labai geros būklės (naudotas), Gamybos metai: 2007, veikimo valandos: 21 676 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 78 t, pildymo angos plotis: 750 mm, pildymo angos ilgis: 1 500 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 600 kg, bendras svoris: 25 000 kg, transporto aukštis: 3 000 mm, alyvos bako talpa: 1 000 l, galia: 55 kW (74,78 AG), tuščias svoris: 25 000 kg, tūrio srautas: 930 m³/val, darbinis slėgis: 250 juosta, Good day, We hereby offer you, subject to prior sale, a used baler from manufacturer Presona AB, type LP 80 VH1. The following technical data has been taken from the operator’s manual and manufacturer brochures. We cannot accept any liability for the accuracy or completeness of this information. Manufacturer: Presona AB, Sweden Type: LP 80 VH1 Year of manufacture: 2007 Total operating hours: 21,676 hours, as of November 2024 Main press force: 78 t Specific press force: 95 N/cm² Pre-press flap force: 28 t Feed hopper dimensions: 1,500 x 1,100 mm Dodpfx Adevgrh Uomela Filling volume / press cycle: 2.7 m³ Throughput capacity under operating conditions: 410 m³/hour Bale dimensions: 1,100 x 750 mm Drive power: 55 kW Tying: 5-fold vertical Hydraulic oil tank volume: 1,000 L Press dimensions when assembled with hopper: 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight (press only): approx. 25 t Note: The machine was used in a recycling operation for compacting paper, cardboard, and film. The baler is in good condition, will remain in operation until January 2025, and can be inspected by appointment. We would be pleased if this machine is of interest to you. Your service team at Mertens & Frowein GmbH

Sąlyga: naujas, Klanke Supercut roll slitter for efficient shredding of reject rolls. Features: - Automatic safety interlock - Emergency stop pull cord Dsden I Rgpopfx Admjla - Siemens PLC Technical specifications: Blade length: 3000 mm Cutting channel opening: 1200 mm Motor power: 15 kW Cutting force: 50 t Made to order. Price and further information available on request. We will be happy to provide you with a non-binding offer.

Gamybos metai: 2003, veikimo valandos: 43 000 h, Sąlyga: reikia remonto (naudotas), mašinos/transporto priemonės numeris: HBC 140 2x75kW 2003 (W230-005), Verkocht door Bollegraaf Recycling Solutions, de originele fabrikant van deze Bollegraaf-pers en -transportband: Bollegraaf HBC140s Balenpers (2x75kW) Pers: Gewicht: 47.100 kg Bouwjaar: 2003 Uitsluitend Hardox bodemplaat Kunststof ventiel Anti-ratten bekabeling Draaiuren: 43.000 Deze balenpers kan ook volledig gereviseerd worden verkocht, conform de 'Bollegraaf OEM Gecertificeerde Revisiestandaarden'. Dit omvat 2 jaar garantie. Neem contact met ons op voor meer informatie of een offerte. Algemene uitgangspunten revisie Reiniging & demontage Voor de daadwerkelijke revisie wordt de pers volledig gereinigd en gedemonteerd in onze revisiewerkplaats. Toleranties Na demontage worden de toleranties van alle stalen componenten gemeten en waar nodig opnieuw gelast. Dit geldt ten minste voor de volgende onderdelen: • Aandrijfram, • Frame, • Kanaal, • Voorpersklep Na demontage en inspectie wordt de ram opnieuw opgelast en voorzien van nieuwe ramwielen. De beschermroosters en de voorpersklep worden uitgedeukt en waar nodig gerepareerd. Dledpjkcgynsfx Admea Overschilderd Na het meten van de toleranties en het uitvoeren van eventuele herstel- en laswerkzaamheden, worden alle onderdelen gestraald en opnieuw gecoat. Hydrauliek: De hydrauliektank wordt gereinigd. De hydraulische leidingen & slangen worden vervangen. De hydraulische componenten worden opnieuw afgedicht. De hydraulische olie wordt ververst. Bekabeling: Alle bekabeling wordt gecontroleerd en indien nodig vervangen. Alle lasdozen worden vervangen en teruggeplaatst op goed toegankelijke posities. Slijtdelen: Alle slijtdelen worden vervangen. De pennen en assen van de cilinders en het kanaal worden vernieuwd. Alle slijtdelen van de beide naaldeninstallaties en knopers worden vernieuwd. Cilinders: De cilinders worden opnieuw afgedicht en, indien nodig, voorzien van een nieuwe chroomlaag of een nieuwe cilinderstang. MCC-kast De schakelkast wordt gecontroleerd en gereinigd. Indien nodig worden elektronische componenten vernieuwd. De PLC en HMI (bedieningsinterface) worden vervangen door de nieuwste Schneider M340-versie inclusief de nieuwste software.

Sąlyga: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2007, veikimo valandos: 22 605 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 100 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 600 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 1 100 mm, balo svoris: 1 400 kg, įėjimo srovė: 238 A, bendras svoris: 36 000 kg, alyvos bako talpa: 1 300 l, For sale is a refurbished baler with 100 t pressing force, large format 1100 x 1100 mm, 75 kW drive power, and a 10-fold cross-tying system. Technical Data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main press force: 100 t Prepress force: 50 t Operating hours: 22,605 h Feed opening dimensions: 1,600 x 1,100 mm Filling volume per press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale dimensions: 1,100 x 1,100 mm Drive power: 75 kW Connected load: 126 kW Total current consumption: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a Bulk density of 30 kg/m³: approx. 16 t/h Bulk density of 50 kg/m³: approx. 25 t/h Bulk density of 100 kg/m³: approx. 47 t/h Bale weights up to 1,400 kg, depending on material and bale length Oil tank capacity: approx. 1,300 l PLC: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Baler dimensions assembled with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Remarks: The baler has been partially refurbished, serviced in our workshop, tested after completion, and stored. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment works have been carried out: - Derusting and partial repainting of the baler - Complete draining of the hydraulic oil tank, replacement of oil and air filters - Refilled with new hydraulic oil - Replaced all hydraulic hoses - Disassembled, overhauled, and reassembled main hydraulic cylinder, two pre-press flap cylinders, and channel press cylinder: honed cylinder tubes, renewed all seal kits, and carried out final pressure test - Dismantled pre-press flap with bearings and bearing brackets. Removed and re-welded 1st and 3rd arc segment - Renewed both bearings on pre-press flap shaft - Renewed upper material retainer on pre-press flap frame Dlsdpfovf E Avox Admsa - Dismantled the press ram, inspected and replaced both front running wheels - Removed and replaced material retainers and wear profiles on sides and bottom of the press ram - Dismantled, overhauled horizontal and vertical needle and tying units, replaced plastic sliding plates, bearings for twister shafts and wire guide pulleys on the needle heads - Replaced both bronze slide rails left and right in press ram frame cover - Renewed both wire redirect units left and right, incl. bale retention clamps - Fully renewed wire feeding unit incl. hydraulic cylinder under the needle passages - Welded and smoothed out wire grooves on the bottom and side walls of the press channel - General maintenance and service work according to manufacturer’s recommendations - Baler tested in both manual and automatic mode after completion of refurbishment, accepted and stored All technical information is provided without liability for errors or omissions.

Sąlyga: naudotas, Gamybos metai: 2003, Technical Details: Pressure: 40 t Box opening: 1200 x 730 mm Material: Cardboard, plastic – cardboard bottles Voltage: 400 / 50 V / Hz Total power requirement: 16.4 kW Transport dimensions (machine): 6.5 x 6.2 x 2.7 m Fully automatic hydraulic CHANNEL BALER for recycling with feed unit/conveyor belt LxW: 4500x1000 mm, motor-driven with automatic 3-fold tying unit Bale counter/indicator Press chamber LxWxH: 1800x800x800 mm with 1.2 m³ volume Bale size LxWxH: 300–1500 x 800x800 mm Dljdpfx Aju Nw Ezodmja Bale weight: 250 – 450 kg depending on material and bale length Filling opening LxW: 1200x730 mm, filling height 1200 mm Hopper size LxWxH: 1200x1200x1400 mm; filling height 2500 mm