Konvejerio juosta Pasvirusi konvejerio juosta Konvejerio sistema

die magnetprofis 2021100803

Sąlyga: labai geros būklės (naudotas), Gamybos metai: 2023, veikimo valandos: 1 851 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 70 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 400 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 500 kg, bendras svoris: 17 000 kg, alyvos bako talpa: 70 l, Technical data baler: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: AVOS 1410 BS-22/50 Year of manufacture: 2023 Operating hours pump: 1,851 hours (as of July 2024) Press force: 70 t (equipped with a 70 t hydraulic cylinder, special equipment) Specific press force: 90.9 N/cm² (equipped with a 70 t hydraulic cylinder, special equipment) Feed chute dimensions: 1,400 x 1,000 mm Theoretical cycle time: 13 seconds Theoretical throughput: 266 m³/hour Bale dimensions: 1,100 x 750 mm (W x H), length variable Drive output: 22 kW Total connected load: 65 kW Tying: 4-fold vertical, fully automatic Throughput at a bulk density of: 30 kg/m³ approx. 5.5 t/hour Tjdpfx Ageu Thbxo Rjf 50 kg/m³ approx. 7.5 t/hour 100 kg/m³ approx. 9.7 t/hour Bale weight at a bale length of approx. 1.2 m: up to 500 kg, depending on material PLC: Siemens S7-1500 Operator panel: Schneider Harmony Press dimensions installed: 8,610 x 2,400 x 3,835 mm (L x W x H) Transport weight baler: 17 t Special equipment: - Wear-resistant floor made of HARDOX steel - Larger main hydraulic cylinder with 70 t pressing force - Special press ram for compacting loose bulk materials of small particle size - OptiCut XS system for reduced cutting forces and increased throughput - Special press plunger for compacting challenging materials Technical data conveyor belt: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: KGF GB 1500 Year of manufacture: 2023 Drive output: 4.0 kW Belt speed: approx. 0.3 m/second Feed belt length: 2,679 mm Incline belt length: 6,866 mm Gooseneck length: 1,272 mm Incline: 35° Usable width: 1,400 mm Sidewall height incline belt: 800 mm Cleat height: 50 mm Cleat spacing: 750 mm Belt specification: EP 400/3, 3:1 (DIN Quality N) Overall height: 4,515 mm Transport dimensions overall: 11,148 x 2,502 mm (L x W) Technical data contactless personnel protection system: Manufacturer: BOREMA Umwelttechnik AG, Switzerland Model: APSS iBOR 22 Year of manufacture: 2023 Condition of the baling plant: Due to the low operating time of only 1,851 pump hours and the exclusive processing of paper, cardboard, and film, the entire plant is in very good condition. Scope of delivery: - Avermann baler, type AVOS 1410 BS-22/50, incl. wire tying stations and bale chute - Avermann conveyor, type KGF GB 1500 - BOREMA personnel protection system, type APSS iBOR 22 Notes: Full documentation (operating manual, CE declaration, electrical/hydraulic wiring diagram) is available. Viewing is possible by appointment. We assume no liability for the technical data or any possible errors.

Sąlyga: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2005, veikimo valandos: 30 408 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 50 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 250 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 720 mm, balo svoris: 550 kg, bendras svoris: 16 000 kg, alyvos bako talpa: 600 l, paskutinio kapitalinio remonto metai: 2024, Technical Data – Baler: Manufacturer: Presona AB Model: LP 50 EH1 Year of manufacture: 2005 Operating hours: 30,408 hours (as of April) Number of bales pressed: 198,059 units (as of April) Main press ram force: 50 t Specific pressing force: 63 N/cm² Theoretical throughput: 530 m³/hour Throughput under operating conditions: 260 m³/hour Feed chute dimensions: 1,250 x 1,100 mm Press chamber volume: 2.2 m³ Bale dimensions: 1,100 x 720 mm, length variable Drive power: 22 kW Tying: 5-fold vertical, fully automatic Throughput rates at a bulk density of: - 30 kg/m³: 6 to 7 t/hour - 50 kg/m³: 7 to 9 t/hour - 100 kg/m³: 11 to 14 t/hour Bale density (paper/newspapers): 400 to 550 kg/m³ Hydraulic oil tank capacity: 600 L PLC: Telemecanique TSX Micro Operator panel: Schneider Magelis Effective transport dimensions excl. press: 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight (press only): approx. 16 t Condition of the baler: The machine underwent partial refurbishment and general maintenance in our workshop. After completion of the refurbishment, the baler was tested in operational mode and is now available for immediate sale. The following refurbishments were carried out: General work: - Machine cleaned, derusted, primed, and partially repainted - Wire entry marks in the press channel openings welded and smoothed Hydraulic unit: - Hydraulic oil tank fully drained, cleaned, and refilled with new oil - Oil and air filters replaced - Leaking oil sight glass on the hydraulic tank replaced - All hydraulic hoses replaced Electrical system: Tjdpfxeu Thhrs Ag Ref - Program menu language set to English - Two key switches on the operator panel replaced - Control cabinet replaced - Signal lamp on the control cabinet replaced - Flap limit switch replaced - Wirthulator electrics renewed, connected, and tested Press ram: - All four guide rollers on the press ram removed and replaced - Main hydraulic cylinder disassembled, overhauled (cylinder tube honed, complete seal kit replaced), leak test performed - All wear-resistant plastic blocks on the press ram replaced Pre-press flap: - Both bearings on the pre-press shaft replaced - Both hydraulic cylinders disassembled, overhauled (cylinder tubes honed, complete seal kits replaced), leak test performed - Scraper flap on the pre-press replaced Tying unit: - Two complete needles with wire guide pulleys replaced - Needles adjusted and set - All wire guide pulleys in needle heads replaced - Twisting fingers replaced - Two twister shafts replaced - All eight wear plates on the twister unit, under the twisting fingers, replaced Scope of delivery: Only the baler is sold. Documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is complete and available. Inspection by appointment possible. We do not accept liability for the technical data or possible errors.

Gamybos metai: 2023, Sąlyga: naujas, Fine grinding mill suitable for flour, coffee, dried spices, and more. Grinding range: 20–120 mesh. Throughput: 100–400 kg per hour. Motor speed: 3,400 rpm. Machine weight: 600 kg. Power requirement: 11 kW. The machine is equipped with an additional dust extraction and filtration unit. Entire construction is made from SUS304 stainless steel. Tjdpfx Agjk S Rpuo Ref

Sąlyga: naujas, Nominal capacity up to 2000 kg/h Motor power 1.5 (2.0) kW (hp) Electrical connection 400V 50Hz (3 phase) Tjdpfxsb I Ubwo Ag Rof Electrical fuse 16 A Length 1600 mm Width 700 mm Height 2100 / 2350 mm Feed height 800 mm Weight 200 kg Material 1.4301 / AISI 304 Cleaning connection ½" internal Wash tank connection 2" external Fruit discharge height 1545 mm

Sąlyga: naudotas, Gamybos metai: 2009, veikimo valandos: 20 536 h, spaudimo jėga: 80 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 400 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 600 kg, tuščias svoris: 16 000 kg, Technical Data Press: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: AVOS 1410-45/80 Year of manufacture: 2009 Operating hours: 20,536 hours (as of September 2024) Pressing force: 80 kN Specific pressing force: 103.9 N/cm² Feed opening dimensions: 1,400 x 1,000 mm Theoretical cycle time: 12 seconds Theoretical throughput: 300 m³/hour Bale dimensions: 1,100 x 750 mm (W x H), length variable Drive power: 45 kW Total connected load: 75 kW Tying: 4-fold vertical, fully automatic Throughput capacity at bulk density of: - 30 kg/m³: approx. 6.0 t/hour - 50 kg/m³: approx. 10.5 t/hour - 100 kg/m³: approx. 17.5 t/hour Bale weights at approx. 1.2 m bale length: up to 600 kg, depending on material PLC control: Siemens S7-300 Display panel: pulsotronic Press dimensions (assembled): 8,610 x 2,400 x 3,835 mm (L x W x H) Press transport weight: 16 t Special equipment: - Wear-resistant floor made of HARDOX steel - Special press ram for compacting "difficult" materials and loose bulk goods of small particle size Tedpfx Aeu Thypeg Rjf - Control cabinet air conditioning - Machine base height increase: 200 mm Note: The machine is currently located in our workshop and is being partially overhauled. We anticipate that the overhaul work will be completed by the end of October and the machine will then be tested and released for sale.

Sąlyga: geras (naudotas), Included in the scope of delivery: 01x Rear wall mesh panel, used Material color: cream white Overall width: approx. 2,200 mm Overall height: approx. 1,200 mm Mesh size: approx. 60 x 50 mm Frame profile dimensions (width): approx. 20 x 20 mm Frame profile dimensions (height): approx. 15 x 15 mm Wire thickness: approx. 3.00 mm Tjdpfx Agsm E I Nvo Rsf Weight per piece: approx. 8.14 kg Internal designation: RW-2

Sąlyga: geras (naudotas), Gamybos metai: 1985, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 50 t, kamuolio ilgis: 1 000 mm, ryšulio plotis: 750 mm, ryšulio aukštis: 750 750 750 mm, balo svoris: 500 kg, įėjimo įtampa: 400 V, bendras svoris: 7 500 kg, alyvos bako talpa: 500 l, galia: 30 kW (40,79 AG), tuščias svoris: 7 500 kg, įėjimo dažnis: 50 Hz, Manufacturer: Pal Pacomat V Year of manufacture: 1985 Main press force: 50 t Specific pressing force: 5 kg/cm² Feed channel: 1,000 x 720 mm (L x W) Theoretical throughput capacity: 200 m³/h Bale size: 700 x 1,000 mm (W x H), adjustable length Drive motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8 t The hydraulic unit is operational; the drive motor is currently disassembled. Todpfxjic Rl Do Ag Rof

Gamybos metai: 2020, Sąlyga: naujas, DESCRIPTION Tjdjfz Nakjpfx Ag Rsf The so-called half-water is produced in the demineralised water station using ion exchange technology. The station consists of 3 columns: - Strongly acidic cation exchanger in the sodium cycle, - Strongly basic anion exchanger operating in the chloride cycle, - Carbon filter Our RDI-2 / RDI-4 demineralisation stations are equipped with fully automatic control heads. The columns are made of AISI316L stainless steel.

Gamybos metai: 2019, Sąlyga: beveik kaip naujas (parodų įrenginys), Aluminium flat conveyor belt including substructure. Dimensions: 6000 + 620 x 105 mm Conveyor belt width: 500 mm PVC conveyor belt including cleats, sidewalls, and sealing strip Tsdpfx Aged Ra Uaj Ref V2A stainless steel feed hopper at the beginning of the conveyor belt. * Optionally available with magnetic deflection roller at the end of the conveyor belt. * Optionally available as an inclined conveyor. * Custom designs in all configurations possible.

Sąlyga: naujas, mašinos/transporto priemonės numeris: NEW-83,