Gamybos metai: 2013, būklė: naudotas, Technical data for the bale opener line for RDF, MSW, paper, cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Model: BO 4000 Year of manufacture: 2015 Number of bales opened: 674 units Operating time: only 3 days, exclusively during commissioning of the entire plant upon initial installation Opening time: approx. 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400–1900 mm Max. bale weight: 2,000 kg Conveying height (system): 1,400 mm Max. conveyor width (system): 1,200 mm Dsdpfju Tg I Dox Af Ajcg Materials to be opened: RDF/MSW System availability: 98% Noise level of bale opener line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Operator display: SIEMENS SIMATIC HMI Touch Control system: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: - Feeding conveyor: 3,500 x 1,200 x 1,400 mm - Infeed conveyor to opener: 1,500 x 1,200 x 1,400 mm - Bale opener (gripper with knife) Special equipment: - Oil heater in hydraulic oil tank - Control cabinet heating - Oil cooler for hydraulic unit Explanation regarding the short operating period: The complete Cross Wrap bale opener line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The background for installation was that, in the event of operational disruptions or maintenance of the incineration plant, municipal waste could continue to be accepted, compacted, wrapped, and stored until the disruption was resolved. Then, all the bales would be reopened and the waste would be fed back into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and never used in regular operation afterwards. Only during commissioning and initial testing were 674 bales opened over three days in 2015. The system is in excellent, immediately operational condition. Due to modifications at the incineration plant, the installation area for the bale opener was needed, so the entire line is now available for sale. Brief description of the bale opening process: Pressed bales are placed on the infeed conveyor from the side or rear using a forklift. For opening, the bales must be oriented so that the wire or twine binding runs horizontally to the conveyor; otherwise, the bales must be rotated 90° beforehand. The opening conveyor moves one bale at a time in front of the cutting unit. The grippers secure the wires or twine. The rotating knife cuts the bale lengthwise. Afterwards, the gripper returns to the home position. The opened bale is then conveyed to the discharge chute and falls onto the subsequent conveying system. Remarks: Original price of the entire plant: €296,000. Complete documentation (operating manual, CE declaration, electrical/hydraulic wiring diagrams) is available. The system has been dismantled into transportable units, stored, and is available at short notice for inspection and loading. No liability is assumed for the technical specifications or possible errors.

Gamybos metai: 2013, būklė: naudotas, We hereby offer you a used PET bottle crusher from the manufacturer BOREMA, model R-1200 F, year of manufacture 2013, for residual emptying, degassing, and pre-compacting of PET bottles with volumes from 0.3 to 2.5 liters. The machine is equipped with a chassis and can be driven into and out of the feed chute of your baler. The throughput capacity is approximately 85,000 bottles or about 3 tons per hour. The following technical information is available: Manufacturer: BOREMA Umwelttechnik AG Model: R-1200 F (with hopper for inserting and removing the compactor) Year of manufacture: 2013 Drive power: 11 kW Connected load: 15 kW Rated current: 32 A Pre-fuse: 40 A Design: Continuous flow system Function: Double-rotor press system Rotor pre-tension: Pneumatic, approx. 16 t Overload protection via anti-blocking system Input material: Single-use and reusable PET bottles, 0.3 to 2.5 L capacity Input material: HDPE bottles and canisters up to 3 L capacity Throughput capacity: approx. 3 t/hour, corresponding to approx. 85,000 bottles/hour, depending on size Required compressed air supply: G1/2", 8 bar, 40 L/min Compaction ratio: 1:3 Flange dimensions (internal): 972 x 1,220 mm (L x W) Infeed opening: 565 x 1,280 mm (L x W) Weight: approx. 2,500 kg Applications: Thanks to the chassis, the PET compactor can be positioned in the feed chute of your baler as needed, ensuring residual emptying, degassing, and pre-compacting of bottles and packaging. When changing materials, the PET compactor is simply removed from the feed chute, allowing materials such as paper, cardboard, films, etc., to be compacted without the unit. Dsdpfx Aju Thpnef Ascg BOREMA PET Compactor Process: Plastic containers are fed in by two rotating shafts. One shaft is pneumatically pre-loaded with two air bellows and presses the PET bottles against the second rotating shaft with 16 t of force. The sealed plastic containers are compressed, ruptured, and degassed in the process. Residual liquids drain away, and the pre-compacted material drops into the baler. In case of contaminants, the pneumatically pre-loaded shaft yields, allowing the contaminant to pass through without interruption. Key advantages over conventional PET perforators with punch pins or knives: The BOREMA process is considerably more efficient and less prone to wear compared to conventional PET perforators with punch pins or knives. The major advantage is that contaminants (e.g., metal parts, stones, bottles with frozen contents, wood pieces) pass through the pneumatically yielding rotor shaft without interrupting operation or causing major damage. In conventional perforators, pins or knives can break off or become severely jammed with contaminants, requiring shutdown and costly repairs. Notes: Complete documentation (Operating Manual, CE, electrical/hydraulic diagrams) is available. Inspection by appointment is possible. No liability is assumed for technical data or possible errors.

Būklė: dilaminuotas dirbtuvėje (naudotas), Technical Data: Feed Hopper with Hydraulic Moving Floor and Bag Opener for Recyclables from Yellow Bags, Commercial Waste, and Residual Waste: Dedpfxjyizxro Af Ascg Manufacturer: BRT HARTNER GmbH Model: HP5-3035 Year of Manufacture: 2015 Hopper Volume: 30 m³ Drive Power: 17.5 kW Dimensions (current condition): 13,200 x 3,050 x 4,350 mm (L x W x H) Condition of the machine: The feed hopper with bag opener was previously used in a large recycling plant, where recyclables from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened by the bag opener, and the recyclables were conveyed in a metered way to a sorting plant, or commercial waste was fed for further processing. The unit functioned flawlessly until it was dismantled and was replaced by a larger system with a higher throughput. The machine was dismantled in our workshop into individual components, partially overhauled, reassembled, and tested in operation. The following refurbishment work was carried out and the following parts replaced: - Disassembly of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming, and painting of steel components. - Various wear and cover plates were newly manufactured and installed. - Removal of worn ends (approx. 40 cm) of the moving floor pipes. Welding of new pipes and smoothing the moving floor pipes. - Replacement of all sliding plastic panels for the hydraulic moving floor. - Removal of the hydraulic unit from the moving floor, complete draining of the hydraulic oil tank, replacement of oil filters, refill with new hydraulic oil. - Replacement of all three hydraulic blocks, all valves, oil sight glass, and all hydraulic hoses of the hydraulic unit. - Seal kits and hydraulic hoses on all three moving floor hydraulic cylinders replaced. - All six end switches (proximity sensors) on the moving floor replaced. - Conveyor chains on the left and right sides of the scraper conveyor replaced. - Seven carrier strips on the scraper conveyor replaced. - Drive motor for the bag tearing blades replaced. - All nine pneumatic cylinders for the pressure pipes replaced. All pneumatic lines and fittings replaced. - All sliding plastic plates for the hydraulic movement of the bag opener replaced. The bag opener can be retracted for depth adjustment, allowing operation for commercial or residual waste without the use of the bag opener. - Both sides fitted with new lateral collision protection plates. - Various wear parts of the bag opener replaced. - The entire system was completely rewired and electrically connected. - The control unit in the control cabinet was retrofitted by BRT Hartner to independent single control, and the standard program was reinstalled on the controller. - The unit was commissioned and tested by BRT Hartner; see the function video. Remarks: Documentation (operating manual, CE declaration, electrical/hydraulic circuit diagrams) is available. Inspection possible by prior arrangement. We do not accept liability for technical data or possible errors.

Būklė: labai geros būklės (naudotas), Gamybos metai: 2011, Funkcionalumas: visiškai funkcionalus, galia: 9,7 kW (13,19 AG), Technical data for Cardboard Shredder (2-Shaft Shredder): Manufacturer: Presto GmbH & Co. KG Model: PZA Year of manufacture: 2007 Djdpfxsu Tha Is Af Aocg Throughput capacity: 130 m³/hour Speed: 37/9 rpm Motor power: 7.5 / 2.2 kW Electrical connection: 32 A Shredder interior dimensions: 1,490 x 1,320 x 530 mm (L x W x H) Shredder exterior dimensions (without cover): 2,308 x 1,320 x 685 mm (L x W x H) Machine weight: 0.45 t System application: The PZA type cardboard shredder was used in a Dutch logistics center to pre-shred loose, upright cartons from the returns department before baling. Cartons were loaded manually onto the infeed conveyor and transported directly to the shredder via a sliding belt conveyor. The pre-shredded cartons were then conveyed over several hundred meters to the baling press and compacted there. Scope of delivery: 1 unit Presto Cardboard Shredder (2-shaft shredder) type PZA Remarks: The cardboard shredder was an essential part of the disposal line and was well maintained to ensure high availability for the returns department. The machine is in good condition and immediately operational. Price is per unit, ex works from our warehouse in Siddeburen, Netherlands. All documentation (operating manual, CE declaration, electrical/hydraulic schematics) is complete. Inspection by appointment is possible. We accept no liability for technical data or possible errors.

Būklė: geras (naudotas), Gamybos metai: 2010, veikimo valandos: 3 641 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 36 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 080 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, galia: 15 kW (20,39 AG), tūrio srautas: 90 m³/val, Technical Data of Baler: Manufacturer: Presto GmbH & Co. KG Model: CC 36 M Year of Manufacture: 2010 Operating Hours: 3,641 hours Pressing Force (Main Press): 36 t Specific Pressing Force: 467 N/cm² Feed Opening Dimensions: 1,080 x 1,100 mm (L x W) Cycle Time: 34 seconds Filling Volume per Cycle: 0.85 m³ Theoretical Throughput: 90 m³/hour Throughput Under Operating Conditions (with material bulk density of 35 kg/m³): approx. 51 m³/hour Bale Dimensions: 1,100 x 750 mm (W x H), length variable Drive Power: 15 kW Tying: 4-fold vertical, semi-automatic, with polyester plastic twine Throughput with Bulk Density of: – 35 kg/m³: 1.8 t/hour – 60 kg/m³: 2.5 t/hour – 100 kg/m³: 3.1 t/hour Transport Dimensions (press only): 4,200 x 1,640 x 2,200 mm (L x W x H) Machine Weight (press): approx. 4 t Remarks: The baler has been function-tested in our workshop, then placed in storage, and is therefore available at short notice. Complete machine documentation (operating manual, CE certificate, electrical and hydraulic schematics) is available. An inspection is possible by appointment. We do not assume liability for any technical specifications or potential errors. Dcjdsu Thh Ejpfx Af Aog

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2015, veikimo valandos: 28 748 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 60 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 500 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 570 kg, bendras svoris: 20 000 kg, alyvos bako talpa: 600 l, galia: 37 kW (50,31 AG), tūrio srautas: 350 m³/val, Technical Data of the Baler: Manufacturer: Presona AB, Sweden Model: LP 60 VH1 Year of Manufacture: 2015 Total Operating Hours: 30,143 hours (as of July 2025) Actual Pump Runtime: 6,527 hours (as of July 2025) Number of Bales Pressed: 115,193 bales (as of July 2025) Pre-Press Force: 25 t Main Press Force: 60 t Djdpfxovn Tg Ie Af Ajcg Specific Press Force: 73 N/cm² Feed Opening Dimensions: 1,500 x 1,100 mm Filling Volume per Press Cycle: 2.7 m³ Theoretical Throughput: 800 m³/hour Throughput Under Operating Conditions: 350 m³/hour Bale Dimensions: 1,100 x 750 mm Drive Power: 37 kW Tying System: 5-fold vertical, fully automatic Throughput at a Bulk Density of 50 kg/m³: 11 to 14 t/hour Bale Weights: 420 to 570 kg, depending on material Hydraulic Oil Tank Volume: 600 L Baler Dimensions Assembled with Hopper: 10,100 x 3,750 x 4,310 mm (L x W x H) Transport Dimensions (excluding press): 10,100 x 2,400 x 3,000 mm (L x W x H) Machine Weight (Press): approx. 20 t Condition of the Baler: The baler has been partially overhauled in our workshop and subsequently tested in manual and automatic operation. The following overhaul work was carried out: - Machine cleaned, partially de-rusted and partially repainted - Hydraulic oil tank fully drained and cleaned - Oil and air filters replaced, new hydraulic oil filled - Press ram disassembled and cleaned - All four press ram rollers disassembled and renewed - Grease cartridges of the automatic roller lubrication system replaced - Guide rails on the baler floor in the pressing chamber cut out - Floor reinforced with welded plates - New HARDOX guide rails welded in - Wire station and deflection pulleys for lower wire cleaned and serviced - Guide rails from the floor of the press channel cut out - New HARDOX guide rails welded in - Both side walls of the press channel disassembled and de-rusted - Worn side wall plates removed - Complete side walls fitted and welded with new wear plates - Main hydraulic cylinder disassembled and overhauled for inspection - Piston rod replaced, cylinder tube honed - All sealing sets replaced, pressure test performed - Vertical needle system for tying disassembled, cleaned, wire deflection pulleys serviced and maintained - Chain cleaned, greased, tension readjusted - Drillomat cleaned, wire cutter, drilling shafts and drilling fingers checked, retorqued, and serviced - Machine inspected, general maintenance work carried out, and baler tested in both manual and automatic operation Remarks: The baler is sold without a conveyor belt and without wire stations. Inspection is possible by prior arrangement. We assume no liability for the technical specifications or any errors.

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2005, veikimo valandos: 30 408 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 50 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 250 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 720 mm, balo svoris: 550 kg, bendras svoris: 16 000 kg, alyvos bako talpa: 600 l, paskutinio kapitalinio remonto metai: 2024, Technical Data – Baler: Manufacturer: Presona AB Model: LP 50 EH1 Year of manufacture: 2005 Operating hours: 30,408 hours (as of April) Number of bales pressed: 198,059 units (as of April) Main press ram force: 50 t Specific pressing force: 63 N/cm² Theoretical throughput: 530 m³/hour Throughput under operating conditions: 260 m³/hour Feed chute dimensions: 1,250 x 1,100 mm Press chamber volume: 2.2 m³ Bale dimensions: 1,100 x 720 mm, length variable Drive power: 22 kW Tying: 5-fold vertical, fully automatic Throughput rates at a bulk density of: - 30 kg/m³: 6 to 7 t/hour - 50 kg/m³: 7 to 9 t/hour - 100 kg/m³: 11 to 14 t/hour Bale density (paper/newspapers): 400 to 550 kg/m³ Hydraulic oil tank capacity: 600 L PLC: Telemecanique TSX Micro Operator panel: Schneider Magelis Effective transport dimensions excl. press: 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight (press only): approx. 16 t Condition of the baler: The machine underwent partial refurbishment and general maintenance in our workshop. After completion of the refurbishment, the baler was tested in operational mode and is now available for immediate sale. The following refurbishments were carried out: General work: - Machine cleaned, derusted, primed, and partially repainted - Wire entry marks in the press channel openings welded and smoothed Hydraulic unit: - Hydraulic oil tank fully drained, cleaned, and refilled with new oil - Oil and air filters replaced Dcsdpfxeu Thhre Af Ajg - Leaking oil sight glass on the hydraulic tank replaced - All hydraulic hoses replaced Electrical system: - Program menu language set to English - Two key switches on the operator panel replaced - Control cabinet replaced - Signal lamp on the control cabinet replaced - Flap limit switch replaced - Wirthulator electrics renewed, connected, and tested Press ram: - All four guide rollers on the press ram removed and replaced - Main hydraulic cylinder disassembled, overhauled (cylinder tube honed, complete seal kit replaced), leak test performed - All wear-resistant plastic blocks on the press ram replaced Pre-press flap: - Both bearings on the pre-press shaft replaced - Both hydraulic cylinders disassembled, overhauled (cylinder tubes honed, complete seal kits replaced), leak test performed - Scraper flap on the pre-press replaced Tying unit: - Two complete needles with wire guide pulleys replaced - Needles adjusted and set - All wire guide pulleys in needle heads replaced - Twisting fingers replaced - Two twister shafts replaced - All eight wear plates on the twister unit, under the twisting fingers, replaced Scope of delivery: Only the baler is sold. Documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is complete and available. Inspection by appointment possible. We do not accept liability for the technical data or possible errors.

Būklė: visiškai atnaujintas (naudotas), Gamybos metai: 2019, veikimo valandos: 3 000 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 70 t, bendras svoris: 9 500 kg, pildymo angos plotis: 420 mm, pildymo angos ilgis: 1 250 mm, Technical data for baler / can press / sheet metal press: Manufacturer: unoTech GmbH Model: UPAXX 70 Year of manufacture: 2019 Operating hours: approx. 3,000 hours Pressing force: 700 kN at 315 bar Filling opening (hopper): 420 x 1,250 mm (D x W) Channel cross-section (bale size): 350 x 500 mm (H x W), length depending on material Drive power: 30 kW Connected load: 40 kW Total current consumption: 70 A Throughput with empty beverage cans: - One press stroke: approx. 1.7 t/h - Two press strokes: approx. 2.5 t/h Achieved compaction: approx. 1,200 kg/m³ Hydraulic oil tank capacity: 850 L Press dimensions assembled: 8,000 x 1,600 x 2,500 mm (L x W x H) Transport weight (press): approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant S355 steel Material suitability: According to the manufacturer, this machine is suitable for pressing tin cans, sheet metal offcuts, steel sheet, as well as aluminum, brass, and copper waste. Condition of the baler: The baler has been completely overhauled in our workshop. The press is in very good condition (see the function video after overhaul) and will be sold with 12 months OBM parts warranty. Djdpfou Th S Sjx Af Aocg Remarks: Complete documentation is available (operating manual, CE declaration, electrical/hydraulic circuit diagram). An inspection can be arranged by appointment. We accept no liability for the technical information provided or for possible errors.

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2002, veikimo valandos: 44 590 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 200 t, pildymo angos plotis: 1 020 mm, pildymo angos ilgis: 2 000 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 1 100 mm, alyvos bako talpa: 3 100 l, galia: 150 kW (203,94 AG), paskutinio kapitalinio remonto metai: 2025, Technical Data - Baler: Manufacturer: MACPRESSE EUROPA S.R.L. Type: 112 Dcedpjx Dnb Uofx Af Ajg Year of manufacture: 2002, partially overhauled in December 2025 Operating hours: 44,590 hours as of December 2025 Main press force: 200 t Specific pressing force: 16.5 kg/cm² Feed chute dimensions: 2,000 x 1,020 mm Filling volume: 2.65 m³ Theoretical throughput: 795 m³/hour Bale dimensions: 1,100 x 1,100 mm, length adjustable Drive power: 2 x 75 kW Binding: 5-fold horizontal, fully automatic Throughput for MSW: approx. 48 to 54 t/hour, depending on material Hydraulic oil tank capacity: 3,100 L Machine weight, press: approx. 50.8 t Scope of delivery: 1 unit baler MACPRESSE, type 111A 1 unit operating manual with CE declaration, electrical and hydraulic schematic Remarks: The machine has been serviced and partially overhauled in our workshop. The following work was performed and parts replaced: • Hydraulic oil tank completely drained and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Dismantling of the press ram, complete disassembly, overhaul of the mechanics • Replacement of the front two main guide rollers • Replacement of the knives on the press ram • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, all seals replaced • Replacement of the counter knife in the frame • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame renewed on left and right sides • Worn press floor cut out, bottom plate replaced with wear-resistant HARDOX steel • Dismantling of the tying and twisting unit, complete disassembly, overhaul of the mechanics, replacement of all twister shafts and ball bearings • Replacement of all wire rollers in the needle heads • Wire cutters cleaned and reset, chains lubricated and tensioned • All wire deflection pulleys made operational • All door contact switches replaced • Vibulator dismantled, disassembled and serviced • General maintenance performed Finally, the baler was subjected to a machine test in both manual and automatic modes—see our video for a functional test of the machine. The documentation (operator manual, CE, electrical/hydraulic schematic) is complete. Viewing by appointment is possible. No liability is assumed for the technical specifications or possible errors.

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 1996, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 170 t, pildymo angos plotis: 1 020 mm, pildymo angos ilgis: 1 800 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 1 100 mm, bendras svoris: 40 000 kg, alyvos bako talpa: 3 000 l, paskutinio kapitalinio remonto metai: 2024, For sale is a used bale press system comprising an underfloor chain belt conveyor with feed hopper, a hydraulic pre-compactor with an agitator, a MACPRESSE 111A baler, two complete wire feed rack units with five spool holders each (no wire included). Technical Data – Baler: Manufacturer: MACPRESSE EUROPA S.R.L. Model: 111A Year of manufacture: 1996, overhauled in 10/2024 Main press force: 170 t Specific compaction force: 14 kg/cm² Feed hopper dimensions: 1,800 x 1,020 mm Fill volume: 2.5 m³ Nominal throughput: 750 m³/h Bale dimensions: 1,100 x 1,100 mm, length variable Drive power: 2 x 55 kW Wire tying: 5-fold horizontal, fully automatic Throughput: approx. 30 to 35 t/h, material dependent Hydraulic tank volume: 3,000 L Transport dimensions (with new machine feet): 11,700 x 2,300 x 2,900 mm (L x W x H) Machine weight: approx. 40 t Notes: The baler has been partially overhauled in our workshop and function-tested upon completion, as shown in our demonstration video. Previously, the line was used for baling paper and cardboard from municipal collection. As the contract was awarded elsewhere at the end of the term, the complete system is now for sale. A detailed photo documentation and our offer outline all performed refurbishment work and the installed new spare parts. Full documentation (operating manual, CE declaration, electrical/hydraulic schematics) is available. Viewing is possible by appointment. No liability will be accepted for technical data or potential errors. Technical Data – Conveyor: Manufacturer: Wagensfeld B.V. Model: Chain belt conveyor 1700 mm Year of manufacture: 2017 Drive power: 7.5 kW Belt speed: 14 m/min Loading belt length: 6,900 mm Incline belt length: 12,885 mm Gooseneck length: 1,747 mm Overall length: 21,271 mm Incline: 32° Usable width: 1,644 mm Drive shaft height above floor: 5,777 mm Side wall height, loading belt: 500 mm Side wall height, incline belt: 880 mm Steel cleat height: 40 mm Cleat spacing: 1,200 mm Transport dimensions (disassembled): 15,005 x 2,500 x 2,435 mm (L x W x H) Pit dimensions: 11,500 x 2,700 x 1,015 mm (L x W x D) Dedpju Th D Refx Af Ascg Notes: The chain belt conveyor, manufactured in 2017, was custom built and installed for the baler during its last installation in the Netherlands. The conveyor is in good, ready-for-use condition and has not been overhauled. An installation drawing with pit dimensions is available. Scope of supply: - 1 unit chain belt conveyor, Wagensfeld B.V. - 1 unit feed hopper with pre-compactor flaps - 1 unit agitator - 1 unit MACPRESSE baler, type 111A - 2 units wire feed racks with wire spool holders, without wire - 1 unit operating manual with CE declaration, electrical and hydraulic schematics

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2007, veikimo valandos: 13 209 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 50 t, pildymo angos plotis: 1 050 mm, pildymo angos ilgis: 1 250 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 700 mm, balo svoris: 500 kg, alyvos bako talpa: 400 l, paskutinio kapitalinio remonto metai: 2025, tūrio srautas: 108 m³/val, Technical data of the baler: Manufacturer (as per nameplate): BRAMIDAN (original manufacturer: Presto GmbH & Co. KG) Model: HC 50 (equivalent to Presto HPK 50) Year of manufacture: 2007 Operating hours: 13,209 hours (as of March) Number of bales pressed: 23,379 pcs Pressing force: 50 t Specific pressing force: 650 kN/m² Feed opening dimensions: 1250 x 1050 mm (L x W) Filling volume: 0.96 m³ Theoretical cycle time: 32 seconds Theoretical throughput: 108 m³/hour Bale dimensions: 1100 x 700 mm (W x H), length variable Drive power: 15 kW Total current consumption: 50 A Binding: 4-fold vertical, fully automatic Throughput at a bulk density of: - 30 kg/m³: approx. 3.1 t/hour - 60 kg/m³: approx. 4.5 t/hour Dcodpfxew U Dt Nj Af Ajg - 100 kg/m³: approx. 7.2 t/hour Bale weights at a bale length of approx. 1.2 m: up to 500 kg (depending on material) Hydraulic oil tank capacity: 400 L PLC: Siemens S7-200 Effective transport dimensions (excluding press): 6780 x 1800 x 2100 mm (L x W x H) Transport weight (press): 8.5 t Condition of the baler: The baler was in use at a production facility, exclusively for compacting cardboard, and has been regularly serviced. With only 13,209 operating hours, the machine has seen relatively low use. The baler has been partially overhauled and thoroughly tested in our workshop. The following overhaul work was carried out: - Machine cleaned - Bale retainer freed up and lubricated - Light barrier replaced - Twister unit completely disassembled, all bearings and plastic sliders replaced, greased, chain tension adjusted - Knife and counter-knife dismantled, sharpened, and reassembled - Knife gap readjusted - General maintenance performed and greased Scope of delivery for the baler: - 1 baler with wire spool boxes (without wire) - 1 set of machine documentation Comments: Complete documentation available (operating manual, CE declaration, electrical/hydraulic schematic). Viewing by appointment. We accept no liability for technical information or possible errors.

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2007, veikimo valandos: 22 605 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 100 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 600 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 1 100 mm, balo svoris: 1 400 kg, bendras svoris: 36 000 kg, alyvos bako talpa: 1 300 l, For sale is a refurbished baler with 100 t pressing force, large format 1100 x 1100 mm, 75 kW drive power, and a 10-fold cross-tying system. Technical Data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main press force: 100 t Prepress force: 50 t Operating hours: 22,605 h Feed opening dimensions: 1,600 x 1,100 mm Filling volume per press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale dimensions: 1,100 x 1,100 mm Drive power: 75 kW Connected load: 126 kW Total current consumption: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a Bulk density of 30 kg/m³: approx. 16 t/h Bulk density of 50 kg/m³: approx. 25 t/h Bulk density of 100 kg/m³: approx. 47 t/h Bale weights up to 1,400 kg, depending on material and bale length Oil tank capacity: approx. 1,300 l PLC: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Baler dimensions assembled with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Dodpfx Aovf E Avjf Ajcg Remarks: The baler has been partially refurbished, serviced in our workshop, tested after completion, and stored. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment works have been carried out: - Derusting and partial repainting of the baler - Complete draining of the hydraulic oil tank, replacement of oil and air filters - Refilled with new hydraulic oil - Replaced all hydraulic hoses - Disassembled, overhauled, and reassembled main hydraulic cylinder, two pre-press flap cylinders, and channel press cylinder: honed cylinder tubes, renewed all seal kits, and carried out final pressure test - Dismantled pre-press flap with bearings and bearing brackets. Removed and re-welded 1st and 3rd arc segment - Renewed both bearings on pre-press flap shaft - Renewed upper material retainer on pre-press flap frame - Dismantled the press ram, inspected and replaced both front running wheels - Removed and replaced material retainers and wear profiles on sides and bottom of the press ram - Dismantled, overhauled horizontal and vertical needle and tying units, replaced plastic sliding plates, bearings for twister shafts and wire guide pulleys on the needle heads - Replaced both bronze slide rails left and right in press ram frame cover - Renewed both wire redirect units left and right, incl. bale retention clamps - Fully renewed wire feeding unit incl. hydraulic cylinder under the needle passages - Welded and smoothed out wire grooves on the bottom and side walls of the press channel - General maintenance and service work according to manufacturer’s recommendations - Baler tested in both manual and automatic mode after completion of refurbishment, accepted and stored All technical information is provided without liability for errors or omissions.

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2000, veikimo valandos: 32 169 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 60 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 320 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 720 mm, balo svoris: 750 kg, bendras svoris: 22 000 kg, alyvos bako talpa: 900 l, For sale is a complete baling press system consisting of conveyor technology, baler (partially overhauled and tested), and wire stations. Technical Data of the Press: Manufacturer: Bollegraaf Recycling Machinery B.V. Model: HBC 60A Dcedpfoviwdmox Af Aeg Year of manufacture: 2000 Operating hours: 32,169 hours (as of November 2024) Main press force: 60 t Pre-press force max.: 25 t Feed opening dimensions: 1,320 x 1,100 mm Theoretical cycle time: 18 seconds Bale dimensions: 1,100 x 720 mm, length variable Drive power: 45 kW Total connected load: 60 kW Tying system: 5-fold vertical Throughput capacity at bulk density: 30 kg/m³ approx. 5.5 t/h 50 kg/m³ approx. 10 t/h 100 kg/m³ approx. 16 t/h Bale weights: 400 up to 750 kg, depending on material PLC control: Telemecanique TSX Micro Machine weight (press): approx. 22 t Scope of delivery: 1 chain belt conveyor 1 Bollegraaf baler HBC 60A with de-flaker (wirbulator) 1 maintenance platform with access ladder 2 wire stations with redirect pulleys for 10 wire coil holders (without wire) The following repair and overhaul work has been carried out: Hydraulic oil tank completely drained, cleaned, and refilled with new oil Oil and air filters replaced Partial resealing of hydraulic block Hydraulic hose at hydraulic block replaced Wire mark grooves at floor entry points welded and smoothed Tying system cleaned and serviced Electrical system overhauled, door flap contact switches partially replaced De-flaker (wirbulator) repaired General maintenance performed, lubricated Machine tested during operation without material, in both manual and automatic modes – see function video Notes: The equipment has already been completely dismantled, stored, and is ready for immediate loading. Documentation (manual, CE, electric/hydraulic wiring diagrams) is available. Inspection possible by appointment. We do not assume liability for technical specifications or possible errors.

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2009, veikimo valandos: 22 029 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 80 t, pildymo angos plotis: 1 000 mm, pildymo angos ilgis: 1 400 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 750 mm, balo svoris: 600 kg, bendras svoris: 16 000 kg, galia: 45 kW (61,18 AG), paskutinio kapitalinio remonto metai: 2025, Technical Data Press: Manufacturer: Avermann Maschinenfabrik GmbH & Co. KG, Germany Model: AVOS 1410-45/80 Year of manufacture: 2009 Operating hours: 22,029 hours (as of December 2025) Press force: 80 kN Specific pressing force: 103.9 N/cm² Feed chute dimensions: 1,400 x 1,000 mm Theoretical cycle time: 12 seconds Theoretical throughput: 300 m³/hour Bale dimensions: 1,100 x 750 mm (W x H), length is variable Drive power: 45 kW Total connected load: 75 kW Tying: 4-fold vertical, fully automatic Throughputs at a bulk density of: 30 kg/m³ approx. 6.0 t/hour 50 kg/m³ approx. 10.5 t/hour 100 kg/m³ approx. 17.5 t/hour Bale weights at a bale length of approx. 1.2 m: up to 600 kg, depending on material PLC controller: Siemens S7-300 Display panel: Pulsotronic Installed machine dimensions: 8,610 x 2,400 x 3,835 mm (L x W x H) Transport weight of press: 16 t Special Equipment: • Wear-resistant floor made of HARDOX steel • Special press ram for compacting 'difficult' materials and loose bulk materials of small particle size • Control cabinet air-conditioning • Machine feet height increase by 200 mm Comment: The machine was serviced and partially overhauled in our workshop. The following work was performed and parts replaced: • Disassembly of the press ram, breakdown into individual parts, overhauling the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right below the press ram o Plastic wear rails left/right above the press ram o Main plastic wear plate (support plate) centrally under the press ram • Steel guide rails left/right above in the frame renewed • Replacement of the entire base plate, four-part, made from wear-resistant HARDOX steel • Wire feed rails in the press floor newly welded and smoothed • Replacement of counter knife, two-part, in the frame • Adjustment of the knife gap to approx. 2.5 mm • Disassembly of the tie and twisting unit, breakdown into individual parts, overhauling the mechanics, replacement of all groove ball bearings and axial ball bearings of the twisting shafts, wire cutters cleaned and re-adjusted, chains lubricated and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses renewed • Oil and air filters renewed • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, was chemically analyzed, is still in good condition and therefore was not replaced; it can continue to be used • General maintenance carried out Dcodpfjx A U Ncjx Af Asg Finally, the press was subjected to a machine test in manual and automatic mode; see video for machine function test.

Būklė: paruoštas naudoti (naudotas), Gniuždymo jėga: apie 700 kN (apie 70 t) Variklio galia: apie 11 kW Maitinimas: 3 × 400 V / 50 Hz Viena ryšulio svoris: iki maždaug 600 kg Ryšulio matmenys: apie 1100 × 1100 × 1200 mm Mašinos matmenys: apie 5,9 m ilgio, 2,5 m pločio, apie 2,6 m aukščio Dodpora Dddefx Af Ascg Mašinos svoris: apie 7 t Ciklo laikas: apie 45–47 s Konstrukcinės ypatybės • didelė įkrovimo anga kartonui • galimybė automatiniam užpildymui (pvz., transporterių) • rankinis vielos surišimas (4 vielos) • padėklo fiksacija ir hidraulinės durys ryšulio paėmimui Šios presės privalumai • dideli ryšuliai = mažiau transportavimo • didelė gniuždymo jėga • pritaikyta nuolatiniam darbui Galimi gamybos metai: 2016-2020

Būklė: paruoštas naudoti (naudotas), * Prekės ženklas: SOTRES * Modelis: nusausinimo įrenginys * Tipas: d 120/20 * Nusausinimo sietų matmenys: 1800 x 1000 mm * Įeina: du vibruojantys varikliai po 2 kW * Ciklonai: 2 vnt. * 1x: ilgis 1600 mm x ⌀ 500 mm * 1x: ilgis 800 mm x ⌀ 250 mm * 2 siurbliai: Warman Schabaver * 1x tipas: 100 f su 22 kW elektros varikliu Dcodpfoywngasx Af Asg * 1x tipas: 40 f su 5,5 kW elektros varikliu * Įskaičiuota: plieninė konstrukcija ir elektros valdymo spinta * Yra sandėlyje: 1 vnt.

Būklė: labai geros būklės (naudotas), Funkcionalumas: visiškai funkcionalus, Techniniai duomenys: - Piltuvo anga 1850 x 1250 mm - Piltuvo talpa apie 3,0 m³ Dsdpfxowb Sdqo Af Ajcg - Rotoriaus skersmuo 500 mm - Rotoriaus ilgis 650 mm - Rotoriaus apsisukimų dažnis apie 160 aps./min. - PLC valdymas - Variklis – reduktorius 45 kW - Valdymo spinta (pilnai sujungta) su 5 m kabeliu - Automatinis žvaigždės-trikampio paleidimas - Svoris 4500 kg - Galingumas priklauso nuo medžiagos Pagrindinės taikymo sritys ir apdorojamos medžiagos: - Spalvotųjų metalų perdirbimas ir tūrio mažinimas - Medienos atliekų perdirbimas ir tūrio sumažinimas - Plastiko, putplasčio / polistireno perdirbimas ir tūrio sumažinimas - Elektros kabelių ir ritinių perdirbimas bei tūrio mažinimas - Plastikinių talpų ir kompozitinių medžiagų perdirbimas ir tūrio sumažinimas

Būklė: naudotas, Gamybos metai: 2016, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 2015-26004, galia: 5,5 kW (7,48 AG), 1.3 Smulkiosios trupinimo sistemos FB 1000 DS1 Smulkintuvas FB 1000 DS1 FG3 Pavaros galia: 5,5 kW + 3,0 kW Konstrukcija: 1 x pjaunamasis velenas su dygliuotais diskais viršuje 1 x dozavimo velenas su dygliuotais diskais apačioje Didžiausias apdirbamos plokštės storis: apie 100 mm Didžiausias apdirbamas tankis: 50 g/litra Laisvas plotis: 1000 mm Padavimo aukštis nuo transporterio: 180 mm Papildomas apsauginis gaubtas ant transporterio, sumontuotas vietoje Dodoyvfhwepfx Af Aecg Sraigtinė iškrova smulkintuvui FB 1000 DS1: Pavaros galia: 0,75 kW Siurbimo antgalis: NW 200 mm Komplekte – techninės priežiūros liukas su saugos jungikliu

Būklė: naudotas, galia: 160 kW (217,54 AG), Pjovimo malūnas DREHER 26/90 / Pjovimo malūnai Staklės su šlifuotais peiliais, tinkamos naudoti kaip malūnas skylučių tinklams ir plėvelės juostoms malti. Techniniai duomenys: Pavaros galia: 7,5 kW Rotoriaus peiliai: 5x3 Statoriaus peiliai: 2x2 Dcjdpfxsy Ic Nwj Af Aog Rotoriaus skersmuo: 260 mm Rotoriaus plotis: 900 mm Su ritininio įvado mechanizmu

Būklė: naudotas, galia: 160 kW (217,54 AG), Nauja hidraulika, nauji peiliai, nauja guoliavietė Pavara: 160,0 kW Rotoriaus peiliai: 5x2 Statoriaus peiliai: 2x2 Rotoriaus skersmuo: 700 mm Rotoriaus plotis: 1200 mm Djdpfjy Ic Nkex Af Ajcg Pajungimo anga: 800 x 1200 mm

Būklė: naudotas, Rotor width: approx. 300 mm Rotor diameter: approx. 300 mm Dodpfx Afsy Ic I He Aocg Stator knives: 6 Rotor knives: 9

Būklė: naudotas, Lėtaeigė išankstinio smulkinimo mašina gumai, plastikui, kabeliams, kompozitinėms medžiagoms Labai tinkama medžiagų junginių atskyrimui, pvz., padangos, senos laidai Su integruota saugos kirpimo sankaba apsaugai nuo pašalinių objektų Rotorius: 600 mm skersmens, 1450 mm darbo plotis Dcedpfx Afey Ic Imj Ajg Uždaro tipo rotorius su paslinktais segmentiniais peiliais, pritvirtintais kasetėse 24 rotoriaus peiliai, 2 statoriaus peilių eilės Atverčiamas sietas, skylės pagal pasirinkimą Su prispaudimo įrenginiu (švytuoklės svirtis) Variklio galia: 90–200 kW

Būklė: naudotas, Heavy-duty cutting mill Dcodpfx Aoy Ic H Njf Ajg Manufacturer: NETZSCH CONDUX Model: CS 500/600-4 Feed opening approx. 600 x 600 mm Semi-open 5-knife rotor, 4 stator knives Drive motor: 75 kW

Būklė: naudotas, Infeed: approx. 300 x 300 mm Rotor width: approx. 280 mm Rotor knives: 3 Stator knives: 2 Dsdpfsy Ic H Ajx Af Ascg Drive: 7.5 kW Double inclined cut With roller feed, electrical switch cabinet, and sound insulation enclosure

Būklė: naudotas, HERBOLD PU800 fine mill Suitable for soft to medium-hard materials Previously used for fine grinding of plastics Grinding disc diameter: 800 mm Drive motor: 90 kW Djdpfx Aey Ic Eljf Aecg