Radialinio gręžimo staklės - Universal

V-TRADE RBT 50/12H

Sąlyga: naujas, Gamybos metai: 2023,

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L x W x H): 720 x 1000 x 1900 mm Weight: 300 kg Total Power Requirement: 1.2 kW Hot Air Furnace MARTINA 55 The MARTINA hot air furnaces are an ideal solution for energy recovery in wood-processing industrial and craft businesses. They are designed to heat large areas, such as workshops and working spaces in trade and industrial operations. These hot air systems require no lengthy warm-up phases and can heat up workshop halls of joineries or carpentries, as well as other production facilities, in a very short time. Solid wood and its by-products (e.g. offcuts from solid wood panels, chips, sawdust, pellets, or briquettes) serve as fuel materials. The MARTINA hot air furnaces comply with EU Directive 98/37CE and Italian Presidential Decree No. 459 dated July 24, 1996, as well as the safety directive of 89/392 CE. All MARTINA series hot air furnaces (models 15 – 30 – 55 – 85 – 120 – 180 – 240 – 350) meet both emission stages according to the 1st German Federal Immission Control Ordinance (BImSchV). - Automatic and continuous air operation - Thermal output: 49.9 kW - Thermal output Kcal: 43,000 - Fuel consumption: 15 kg/h - Air output: 4,900 m3/h - Combustion chamber depth: 650 mm - Loading door: 370 x 350 mm - Hot air blower: 1.12 kW / 230 V - Firebox negative pressure: 0.2–0.3 mbar - Draft requirement at nominal output: 0.18 mbar - Heatable volume: approx. 1,000 m3 - Heatable area: approx. 220 m2 - Space requirement: Width 720 mm, Depth 1,000 mm, Height 1,900 mm - Weight: 300 kg Hnodpfx Ajvz Hq Hsf Ijg - Flue pipe diameter (collar): 160 mm - Chimney diameter (recommended): 200 mm - Efficiency: 85–90% - Chimney discharge pressure: 13 PA - Flue gas temperature: 290°C - Hot air outlet spigots: 2 x Ø 200 mm - For additional technical data, please refer to the attached data sheet The two pipes for outgoing hot air are located at the lower part of the rear side of the furnace. A maximum of 20 meters of ducting per spigot is permitted for air distribution.

Sąlyga: geras (naudotas), Gamybos metai: 2000, Funkcionalumas: visiškai funkcionalus, gręžimo pajėgumas: 40 mm, plunksnos brūkšnys: 200 mm, quill skersmuo: 80 mm, Machine Configuration • Work table 1800 x 600 mm with 4 T-slots • Arm travel 1050 mm • Drilling spindle SK 40 with tool clamping device • Infinitely variable speed programming • Stepless quill feed via three-phase servo motor • 2 T-slots 18 mm at the rear of the machine base • 2 T-slots 18 mm on the left side of the machine base • Thread cutting device • Central lubrication system • Coolant system • Machine lamp • CE marking • Safety guard • USB interface Dimensions and Travel Paths Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column travel (W-axis) mm 410 Distance spindle nose – table surface min. mm 70 / max. mm 680 Distance spindle nose – floor min. mm 970 / max. mm 1580 Drilling radius mm 540 - 1590 Working table height mm 900 Machining Performance Drilling capacity (solid) St 60 Ø 40 mm GG 22 Ø 50 mm Thread cutting St 60 M 36 GG 22 M 42 Main Spindle Drive AC motor, frequency controlled kW 5.5 at 100% duty cycle Speed range: rpm 15 – 2800 Torque Nm max. 250 Hnodpfxeu Aa I So Af Ijg constant between rpm 15 – 2000 Feed Drives X-axis - AC servo motor kW 0.25 Y-axis - AC servo motor kW 0.25 Z-axis - AC servo motor kW 4.50 W-axis - AC servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min 7.5 / 7.5 / 5 Rapid traverse speed (W): m/min 3 Feeds stepless mm/min 5 – 2000 Accuracy Positioning accuracy X-, Y-axis over 1200 mm mm ± 0.075 Electrical Data Operating voltage/frequency V/Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC Control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen, backlit, clearly legible from all sides, 215 x 160 mm Positioning information: Cartesian or polar, values absolute or incremental, mm or inches or degrees Interpolation: 2 axes (X, Y) Technology Database: Tool management, tool suggestions according to machining type, material-dependent cutting data suggestions Tool Management: max. 500 tools Subprogramming: yes Machining Cycles Standard Software Options: Conversational programming, 38 work offset positions, rotation and mirroring, teach-in for X, Y, Z, program restart with selectable functions for targeted program re-entry Zero point determination: Cycles for determining reference points by manually probing the workpiece for: - Arbitrarily clamped rectangular parts - Arbitrarily clamped round parts - Aligning cast and flame-cut parts - Angle detection on round parts by probing reference edges or surfaces Test graphics: Graphical display of drilling patterns Data Interfaces: USB

Sąlyga: naudotas, Gamybos metai: 1994, gerklės gylis: 1 250 mm, Radial Drilling Machine Manufacturer: Breda Model: R 55-1250 Year of manufacture: 1994 Technical Details Manufacturer: BREDA Model: R 55-1250 Arm Length: 1250 mm Drilling capacity in steel: 55 mm Drilling capacity in cast iron: 70 mm Thread cutting in steel: M 50 Thread cutting in cast iron: M 65 Spindle taper: MT 5 Arm reach: 1250 mm Traverse of spindle box: 930 mm Minimum/maximum distance from base plate: 536 – 1375 mm Vertical travel of arm: 705 mm Spindle stroke: 310 mm Number of spindle speeds: 12 Spindle speeds: 30 - 1200 rpm Number of feeds: 8 Feeds: 0.06 – 1.0 mm/rev Base plate: 2070 x 910 mm Base plate clamping surface: 1325 x 910 mm Motor power: 4.4 kW – 380 V Dimensions (L x W x H): 2.1 x 1.0 x 2.5 m Weight: 3 t Accessories Drilling table 750 x 600 x 550 mm Coolant system Hydraulic clamping All information subject to change without notice. A demonstration is possible at any time in our showroom. Hnsdpfjv Rpf Sex Af Ijg

Sąlyga: naudotas, Radial drilling machine CSEPEL Type RFh 75 / 1500 Machine No. 13704 Year of manufacture: 1985 Drilling capacity in steel Ø 75 mm Drilling capacity in cast iron Ø 90 mm Spindle taper MT 5 Nominal arm reach 1500 mm Maximum spindle reach 1500 mm (to column) Minimum spindle reach 440 mm (to column) Distance spindle nose – clamping surface 370 - 1700 mm Vertical adjustment of arm 950 mm Table size / clamping surface 1800 x 1100 mm Column diameter 450 mm Quill stroke 380 mm Spindle speed 19–1900 rpm, 21 steps Feed rate 0.047–2 mm/rev, 12 steps Motor power 11 kW Power supply 380 Volt, 50 Hz, 15 kW - Spindle clockwise/anticlockwise operation via hand lever switch Hsdpfx Aslhwr Rof Ijng - Hydraulic gearshift for spindle speed and feed rate - Hydro-mechanical central clamping - Motorized vertical arm adjustment - No coolant system - Machine lamp - Operating manual included Space required: Length 2720 mm x Width 1170 mm x Height max. 3770 mm Transport height with motor on column: 3500 mm Transport height without motor on column: 3250 mm Weight: 6.3 t Good condition

Sąlyga: geras (naudotas), Gamybos metai: 2016, 1 naudotas 5 ašių apdirbimo centras Gamintojas: Haas, Modelis: UMC-750, Hnodpfx Afoxyinns Ieg Pagaminimo metai: 2016.01, Nuskaitytos įjungimo valandos: 4.960, pastūmos valandos: 10.247 X/Y/Z eiga = 762x508x508 mm, 10.000/5.000 val. Įrankių tvirtinimas: SK40, 40 pozicijų įrankių keitiklis, NC SRT stalo dydis 630x500 mm, Maksimalus stalo apkrovimas: 300 kg, Maksimalus apsisukimo diametras: 686 mm,

Sąlyga: geras (naudotas), Gamybos metai: 1997, Funkcionalumas: visiškai funkcionalus, gręžimo pajėgumas: 40 mm, plunksnos brūkšnys: 200 mm, quill skersmuo: 80 mm, Machine Configuration • Work table 1800 x 600 mm with 4 T-slots • Arm travel 1050 mm • Drilling spindle SK 40 with tool clamping device • Infinitely variable speed programming • Stepless quill feed via three-phase servo motor • 2 T-slots 18 mm at the rear of the machine base • 2 T-slots 18 mm on the left side of the machine base • Thread cutting device • Central lubrication system • Coolant system • Machine lamp • CE marking • Safety guard • USB interface Dimensions and Travel Paths Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column travel (W-axis) mm 410 Distance spindle nose – table surface min. mm 70 / max. mm 680 Hedpfx Aformkfne Ieng Distance spindle nose – floor min. mm 970 / max. mm 1580 Drilling radius mm 540 - 1590 Working table height mm 900 Machining Performance Drilling capacity (solid) St 60 Ø 40 mm GG 22 Ø 50 mm Thread cutting St 60 M 36 GG 22 M 42 Main Spindle Drive AC motor, frequency controlled kW 5.5 at 100% duty cycle Speed range: rpm 15 – 2800 Torque Nm max. 250 constant between rpm 15 – 2000 Feed Drives X-axis - AC servo motor kW 0.25 Y-axis - AC servo motor kW 0.25 Z-axis - AC servo motor kW 4.50 W-axis - AC servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min 7.5 / 7.5 / 5 Rapid traverse speed (W): m/min 3 Feeds stepless mm/min 5 – 2000 Accuracy Positioning accuracy X-, Y-axis over 1200 mm mm ± 0.075 Electrical Data Operating voltage/frequency V/Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC Control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen, backlit, clearly legible from all sides, 215 x 160 mm Positioning information: Cartesian or polar, values absolute or incremental, mm or inches or degrees Interpolation: 2 axes (X, Y) Technology Database: Tool management, tool suggestions according to machining type, material-dependent cutting data suggestions Tool Management: max. 500 tools Subprogramming: yes Machining Cycles Standard Software Options: Conversational programming, 38 work offset positions, rotation and mirroring, teach-in for X, Y, Z, program restart with selectable functions for targeted program re-entry Zero point determination: Cycles for determining reference points by manually probing the workpiece for: - Arbitrarily clamped rectangular parts - Arbitrarily clamped round parts - Aligning cast and flame-cut parts - Angle detection on round parts by probing reference edges or surfaces Test graphics: Graphical display of drilling patterns Data Interfaces: USB

Sąlyga: naudotas, Gamybos metai: 1991, Drilling capacity in steel (diameter) 50 mm Outreach 1100 mm Workpiece height - max. approx. 1000 mm Drilling capacity in cast iron 60 mm Spindle taper MK 5 Spindle speeds 28 - 2500 rpm Feeds 0.05 - 2 mm/rev Quill stroke 300 mm Distance base plate - spindle nose 630 - 1380 mm Hsdsu Sblwspfx Af Isng Vertical arm adjustment 750 mm Total power requirement 6 kW Machine weight approx. 4 t Machine dimensions L x W x H 2,740 x 1,140 x 2,590 mm - with tapping unit - Accessories: Cube table LxWxH = 550 x 550 x 550 mm, machine vice, coolant system

Sąlyga: naudotas, rida: 790 000 km, galia: 357 kW (485,38 AG), pirmoji registracija: 07/2011, kuro tipas: dyzelinas, bendras svoris: 23 500 kg, ašių konfigūracija: 6x4, stabdžiai: variklio stabdymas, vairuotojo kabina: miegamoji kabina, pavaros tipas: mechaninis, emisijos klasė: Euro 5, pakaba: plienas-oras, Here’s your chance to drive a US truck and transport up to 28 pallets if needed. The price includes the trailer (first registration 2015). We can completely remove the body for you so you have a tractor unit again, or set it up purely as a show truck for cruising. Modifications such as chrome parts and LEDs are included in the price, subject to agreement with you! Cummins ISX 15L 18-speed Fuller 2 beds Original Peterbilt leather seats Typical Peterbilt interior, fully equipped The truck has too many extras to list here. Hnsdpfx Afoqx Sule Ieg If you have further questions, feel free to contact us by email or phone. The price includes German vehicle documents. Subject to errors and prior sale. Financing and trade-in possible—let us know what you have. Tipper hydraulics available at extra cost! Our motorhomes are cleared through customs, taxed in Germany, and include EU vehicle documents. For us, quality is our name. Didn't find your dream vehicle among Europe's largest US truck inventory? Not your company’s or favourite colour? No problem... We have access to 500 more trucks and motorhomes in the USA and Canada, both new and used, from all brands. We also cooperate with one of the best paint shops in Germany. Let us advise you and offer you a free quote. We look forward to your call. Viewings are only possible by appointment.

Sąlyga: labai geros būklės (naudotas), Maximum swing over bed: 575 mm Hnjdpjwlgdyjfx Af Ieg Maximum swing over carriage: 525 mm Maximum swing over cross slide: 300 mm Distance between centers: 2000 mm Spindle bore diameter: 51 mm Number of spindle speeds: 18 Spindle speed range: 32 to 2500 rpm Bed width: 400 mm Maximum cross slide travel: 305 mm Maximum top slide travel: 140 mm Maximum tailstock quill travel: 150 mm Overall dimensions: 3405 x 1175 x 1345 mm Machine weight: 2200 kg