Daugiafunkcis vėdinimo matuoklis

TSI VelociCalc 9565

Gamybos metai: 2024, būklė: naujas, mašinos/transporto priemonės numeris: H3000-H5000TM,

Būklė: naudotas, Gamybos metai: 1996, Diameter / mm Workpiece length / mm Length / mm MITUTOYO SURFTEST SV-500 roughness tester with OLZE measuring plate Dimensions: 600 x 600 x 80 mm Target µm: 16 Actual µm: 10.00 Dedpfotvm Smjx Ac Heup Net weight: 85 kg Information regarding scope of delivery The package contains only the ordered product. Any additional decorative items or other objects shown in the product images are not included in the delivery.

Būklė: naujas, Gamybos metai: 2025, bendras aukštis: 4 000 mm, bendras ilgis: 7 000 mm, bendras plotis: 3 000 mm, garantijos trukmė: 24 mėnesiai, temperatūra: 80 °C, oro poreikis: 36 000 m³/val, įėjimo įtampa: 380 V, šildymo galia: 345 kW (469,07 AG), galia: 40 kW (54,38 AG), kuras: suskystintos naftos dujos (LPG), energijos suvartojimas: 40 kWh, izoliacinė medžiaga: Mineralwolle, izoliacijos storis: 50 mm, nominali galia: 345 kW (469,07 AG), Įranga: apšvietimas, MAIN STANDARD Our spray booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. The processes in the booth are managed via a PLC system, ensuring that the desired parameters are consistently maintained. FUNCTIONAL PRINCIPLES OF THE BOOTH The processes within the booth are operated using a control panel that manages the following steps: Dusdpfx Ajwzmcbjc Hep PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at external temperature. The air is then expelled through the extraction unit. Floor filters (paint stop) capture paint particles, and the air passes through the final exhaust filters before release. FLASH-OFF PROCESS After painting, the booth continues operation for approximately 15 minutes to remove residual solvents and thinners. During this process, fresh outside air continues to circulate in the booth. DRYING PROCESS In this phase, 80% of the air circulating through the booth is heated to 60°C and introduced to the booth via a distributor. As 20% of solvent is released during drying, it is expelled together with this exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted via the control panel as required. COOLING PROCESS After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system is restarted. During the 5-minute cooling phase, fresh air from outside circulates within the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels manage the functions and operation of the machinery and devices installed in the booth. The panel is constructed from durable galvanized sheet and steel profiles, and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel includes essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control connections between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for booth relocation if necessary. • Operating equipment runs on 380 V 50 Hz, while control units use 220 V. • Booth operating time can be monitored on the electronic control panel for easy maintenance tracking. • Temperature and time settings for paint flashing, intermediate drying, and final drying can be easily adjusted via the digital display on the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Būklė: visiškai atnaujintas (naudotas), Galimi gumos bandymo prietaisai Dodpfjwmnlhox Ac Houp 1 x Alpha Production MDR reometras (pageidaujant konteineryje su pneumatiniu mėginių štampavimo įrankiu) Prietaisas patikrintas, sukalibruotas ir aprūpintas nauja programine įranga naujame Tower kompiuteryje!

Būklė: naujas, Gamybos metai: 2026, Powder spray booths available in various sizes and configurations. Accessories available upon request. Dodpjizw Hyofx Ac Hsup

Būklė: naudotas, Hardness tester, hardness testing machine, hardness tester, hardness tester, impact hardness tester - Delivery: as is, as inspected Duodpfehck U Sjx Ac Hep - Tool set: incomplete - Hahn & Kolb: portable hardness tester - Individual components: see photos - Box dimensions: 355/190/H95 mm - Weight: 5.4 kg

Būklė: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, bendras aukštis: 5 600 mm, bendras ilgis: 11 200 mm, bendras plotis: 5 100 mm, įvesties srovės tipas: trifazis, garantijos trukmė: 24 mėnesiai, vidinis aukštis: 4 970 mm, vidinis ilgis: 11 000 mm, temperatūra: 80 °C, vidinis plotis: 5 000 mm, oro poreikis: 52 000 m³/val, įėjimo įtampa: 380 V, šildymo galia: 250 kW (339,91 AG), galia: 45 kW (61,18 AG), kuras: suskystintos naftos dujos (LPG), įėjimo dažnis: 50 Hz, energijos suvartojimas: 45 kWh, izoliacijos storis: 50 mm, nominali galia: 250 kW (339,91 AG), plieno lakšto storis (maks.): 2 mm, Įranga: apšvietimas, * Air Treatment Unit: The air treatment unit is a recirculation system that supplies the cabin with filtered fresh air and expels used air during the painting process. It heats the air to 60°C, mixes 10% fresh air with recirculated air via an automatic multi-damper system, and reheats the air before it is fed back into the cabin. Air is heated using a burner and heat exchanger, both made from high-grade 304 stainless steel and housed in the fresh air unit. During painting, the air passes through two stages of filtration (front and ceiling filters) before entering the cabin. The contaminated air is also filtered twice (inlet and outlet filters) before leaving through the extraction unit. Air treatment units are insulated like the side walls to minimize heat loss and are equipped with rubber seals on the covers to protect against possible vibrations and noise. The exhaust air is regulated by a damper in the exhaust air duct, which helps control the cabin’s internal pressure. * PRINCIPLE OF OPERATION FOR THE CABIN: Processes inside the cabin are controlled via an operator panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passes through front filters before entering the distribution chamber at ambient temperature. The air is then extracted through the exhaust unit. Floor filters (paint stop) capture paint particles, and the air passes through final exhaust filters before being released. * FLASH-OFF PROCESS: After painting, the cabin continues to operate for about 15 minutes to expel residual solvents and thinners. During this process, fresh air from outside circulates in the cabin. * DRYING PROCESS: In this phase, 80% of the air circulating through the cabin is heated to 60°C and supplied to the cabin via the distributor. Since 20% of the solvents are released during drying, they are expelled along with this air. Industrial paints are generally dried at 60°C, though the cabin temperature can be adjusted via the operator panel as needed. * COOLING PROCESS: After the 30-minute drying phase, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system is restarted. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system shuts down automatically. Duedpfx Ajwzl Hxec Hsp ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices integrated into the cabin. The panel is constructed from robust galvanized sheet metal and steel profiles, and is fully enclosed for protection from dust and moisture. Electrical Components and Switching Panels: • The switching panel includes all necessary components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for control and command connections between the control panel and motors or other electrical devices. • Wiring is designed to allow for cabin relocation, if required. • Operating equipment is powered at 380 V 50 Hz, while control devices run at 220 V.

Būklė: naudotas, Gamybos metai: 1957, Brinell 250 kg Rockwell 150 kg Throat depth: 130 mm Test height: 300 mm Machine weight approx. 0.150 t Space requirements approx. 650 x 530 x 1550 mm Testing according to the Rockwell, Vickers, and Brinell methods. Djdpfx Asu T R Tkjc Hsup This is a used device, therefore sold without any warranty or guarantee.

Būklė: naudotas, SPECTRO SPECTRO MAXx / LMM04 Description: For sale is an optical emission spectrometer SPECTRO MAXx for professional metal and alloy analysis. This device is suitable for fast and precise determination of the chemical composition of metals such as steel, cast iron, and various non-ferrous alloys. It is a proven industrial unit, commonly used in foundries, laboratories, and for quality assurance. Device and maintenance information: Duedpfoybcfksx Ac Hep The unit was covered by a maintenance contract and professionally serviced on a regular basis. Several programs were calibrated annually. Last maintenance: 22.12.2023 Operation without vacuum pump – purging is performed exclusively with argon. Regularly calibrated programs: Fe-10, Fe-15, Fe-30 Al-10, Al-20 Cu-20 Overview of installed programs: Fe-01-M / Fe-10 – Low-alloy steel Fe-01-M / Fe-30 – Cr- / CrNi steel Fe-15-M / Fe-15 – Free-cutting steel Al-01-M / Al-10 – Pure aluminium Al-01-M / Al-20 – AlSi alloy Cu-01-M / Cu-20 – CuZn alloy Technical data: Device data: Type: Optical Emission Spectrometer (OES) Manufacturer: SPECTRO / AMETEK Model: SPECTRO MAXx Design: Benchtop unit Electrical data: Power supply: 115 / 230 V AC Frequency: 50 / 60 Hz Power consumption (measuring mode): approx. 400 VA Power consumption (standby): approx. 180 VA Fuse: 16 A (slow-blow) Gas supply: Operating gas: Argon (Ar) Argon purity: min. 4.8 (99.998 %) Input pressure: approx. 7 bar Argon consumption: Stand-by: approx. 6 l/h Continuous operation: approx. 23 l/h Analysis operation: approx. 200 l/h Ambient conditions: Operating temperature: +10 °C to +30 °C Humidity: 20–80 %, non-condensing Dimensions & weight: Dimensions (W × D × H): approx. 600 × 740 × 460 mm Weight: approx. 60 kg Important note: The table shown in the photos is not included in the sale. Condition: used Scope of delivery (see pictures): SPECTRO MAXx spectrometer PC with monitor, keyboard and mouse Argon unit Original manuals and software media Subject to change and errors in the technical data. For further questions, we are happy to assist you by phone.

Gamybos metai: 2000, būklė: geras (naudotas), Matuoklis dujų kiekiui izoliaciniame stikle tikrinti. Matmenys: plotis – 245 mm, gylis – 185 mm, aukštis – 95 mm, svoris – apie 3 kg. Dedjht Evpopfx Ac Houp