Šerdelės vamzdžių lenkimo staklėsTRANSFLUID
DB 628 ST / SPS
Šerdelės vamzdžių lenkimo staklės
TRANSFLUID
DB 628 ST / SPS
Gamybos metai
1996
Sąlyga
Naudotas
Vieta
Bünde 

Rodyti vaizdus
Rodyti žemėlapį
Duomenys apie mašiną
- Įrenginio aprašas:
- Šerdelės vamzdžių lenkimo staklės
- Gamintojas:
- TRANSFLUID
- Modelis:
- DB 628 ST / SPS
- Gamybos metai:
- 1996
- Sąlyga:
- geras (naudotas)
Kaina ir vieta
- Vieta:
- Bünde bei Bielefeld
Skambinti
Pasiūlymo informacija
- Sąrašo ID:
- A18322811
- Nuorodos Nr.:
- 1082-12117
- Naujinta paskutinį kartą:
- Data 2025.04.30
Aprašymas
Tube diameter: 6 - 28 mm
Wall thickness: 2 mm
Minimum bending radius: 2 x D
Control system: IPU 20
Maximum bending radius: 5.0 x D mm
Maximum bending angle: 190°
Mandrel length: 3000 mm
Operating pressure: 180 bar
Hydraulic motor: 4 kW
Machine weight: approx. 900 kg
Fjdpfxsvtgn Ns Acuegh
Space required: approx. 3.8 x 1.1 x 1.3 m
Semi-automatic electro-hydraulic mandrel tube bending machine equipped with PLC control for 20 bending angles, with display on the control panel for presetting the bending angle, angle detection, and angle measurement via absolute value rotary encoder, automatic tool tray return, rotation device with digital display, hydraulic quick-release chuck, automatic mandrel lubrication, and adjustable length stops.
Operating modes: MANUAL and semi-automatic.
Control buttons: hydraulic on/off, operating mode selection, clamp close/open, advance/retract clamp, mandrel in/out, bend in/out, lock in/out, mandrel lubrication, rotation device in/out, tool tray return, advance length stop, emergency stop.
The machine comes from prototype construction and was only minimally used until 2000. Afterwards, the machines in this department were sold. However, the buyer did not use the tube bending machine, so it has only been stored and has not been operated since then (original paintwork).
This is a used machine, therefore we sell under exclusion of any warranty.
STOCK-HOLDING DEALER WITH 1,600 m² SHOWROOM.
Skelbimas verčiamas automatiškai, todėl jame gali būtų vertimo klaidų.
Wall thickness: 2 mm
Minimum bending radius: 2 x D
Control system: IPU 20
Maximum bending radius: 5.0 x D mm
Maximum bending angle: 190°
Mandrel length: 3000 mm
Operating pressure: 180 bar
Hydraulic motor: 4 kW
Machine weight: approx. 900 kg
Fjdpfxsvtgn Ns Acuegh
Space required: approx. 3.8 x 1.1 x 1.3 m
Semi-automatic electro-hydraulic mandrel tube bending machine equipped with PLC control for 20 bending angles, with display on the control panel for presetting the bending angle, angle detection, and angle measurement via absolute value rotary encoder, automatic tool tray return, rotation device with digital display, hydraulic quick-release chuck, automatic mandrel lubrication, and adjustable length stops.
Operating modes: MANUAL and semi-automatic.
Control buttons: hydraulic on/off, operating mode selection, clamp close/open, advance/retract clamp, mandrel in/out, bend in/out, lock in/out, mandrel lubrication, rotation device in/out, tool tray return, advance length stop, emergency stop.
The machine comes from prototype construction and was only minimally used until 2000. Afterwards, the machines in this department were sold. However, the buyer did not use the tube bending machine, so it has only been stored and has not been operated since then (original paintwork).
This is a used machine, therefore we sell under exclusion of any warranty.
STOCK-HOLDING DEALER WITH 1,600 m² SHOWROOM.
Skelbimas verčiamas automatiškai, todėl jame gali būtų vertimo klaidų.
Tiekėjas
Pastaba: Užsiregistruokite nemokamai arba prisijunkite, kad gautumėte visą informaciją.
Registruota nuo: 2005
Pateikti užklausą
Telefonas & Faksas
+49 5223 ... skelbimai
Jūsų skelbimas sėkmingai pašalintas
Įvyko klaida