"Sidel SBO 6/10" tempiamojo išpūtimo liejimo mašina

SIDEL SBO 6/10

Sidel Stretch Blow Moulding Machine
Max. output: 6,000 bottles/hour
Max. bottle size: 3,000 cc
Blow stations: 6

The machine is in very good, well-maintained condition.

GENERAL INFORMATION
The SBO 6/10 features 6 moulds and 10 heating modules. Suitable for a wide range of bottle sizes and styles from 0.25 to 3 liters. Sidel’s two-stage PET stretch blow moulding machines require pre-manufactured preforms to be fed into the machine. Separating bottle production from preform manufacturing enables production optimization, greater operational flexibility, and higher productivity and yield.

MAXIMUM PREFORM DIMENSIONS
Neck height: 9 – 41 mm (measured from bottom edge of support ring)
Minimum neck internal diameter: 19 mm
Maximum neck external diameter: 34 mm
Preform support ring diameter: 29 – 51 mm
Maximum preform length: 210 mm
Lsdpfxsg Ailcj Apnohn

MAXIMUM BOTTLE DIMENSIONS
Maximum bottle diameter: 130 mm
Maximum bottle height: 380 mm
Bottle volume: 0.25 – 3 liters

AVERAGE PREFORM WEIGHTS (for still and carbonated liquids)
0.25-liter bottle: 14-20 grams
0.50-liter bottle: 20-33 grams
1.00-liter bottle: 26-40 grams
1.50-liter bottle: 35-51 grams
2.00-liter bottle: 44-58 grams
3.00-liter bottle: 68-84 grams

BLOW MOULDING WHEEL
Height: 3.5 meters
Number of moulds: 6
Clamping force: 10 tonnes
Discharge height (under neck): approx. 1.4 meters
Machine DC drive motor output: 4 kW

HEATING SECTION
Height: 2 meters
Number of oven heaters: 10
Heating zones per unit: 8
Max. output: 170 kW

ELECTRICITY CONSUMPTION
Max. connected load: 200 kW
Average consumption: 100-150 kWh (varies by bottle produced)

COMPRESSED AIR
Available pressure: 7-35 bar
Pressure: 7 bar
Flow rate: 50–100 Nm³/h (varies by bottle produced)
Blow pressure – champagne base: up to 25 bar
Blow air flow – champagne base: 110–550 Nm³/h
Blow pressure – petaloid base: up to 35 bar
Blow air flow – petaloid base: 155–770 Nm³/h

COOLING WATER
Temperature: 10-12°C
Pressure: 5-6 bar
Flow rate: up to 6 m³/h
Cooling requirement: up to 16,000 Kcal/h

WEIGHT
Blow moulding wheel with moulds: 8 tonnes
Heating section: 2.2 tonnes
Preform feeder: 0.65 tonnes
Control cabinet: 0.85 tonnes

PREFORM HEATING SECTION
The preforms are transported neck upwards to the heating unit. This unit continuously ensures that preforms are inverted before passing (neck down) in front of the heating modules, and then turned again. During the heating phase, preforms are rotated and their necks are shielded from heat to optimize temperature distribution without deforming the neck. Heating is provided by 10 heating modules. Each unit can be fitted with up to 8 horizontally stacked, air-cooled infrared lamps. The heating power of each of the 8 lamp zones is adjustable to optimize the thermal profile. These zones are regulated on all SBO models. After heating, infrared temperature measurement of the preform allows further regulation of controlled zones, ensuring uniform preform temperature is maintained.

Skelbimas buvo automatiškai išverstas. Galimos vertimo klaidos.