Ratu Balansavimo Stakles pirkti naudotą (55 938)

Būklė: naudotas, Gamybos metai: 1985, Wheel diameter – max. 80 mm Wheel width 150 mm Module – max. 2.5 Module – min. Total power requirement 10 kW Machine weight approx. 2,400 kg Fully automatic hobbing machines for worm gear cutting Type A 33 / 1 Year of manufacture 1985 Serial No. 14.06/14.07/14.15 TECHNICAL DATA: Max. wheel diameter without parts magazine approx. 80 mm Max. wheel diameter with parts magazine approx. 50 mm Max. module 2 / 2.5 Axial cutting length approx. 150 mm Max. workpiece installation length approx. 200 mm Fsdpet Hw D Rjfx Ahwopd Milling slide swivels up to 90 degrees Cutter – diameter 24 – 50/63 mm Max. radial travel of the milling slide 0–14/18 mm Max. milling cutter shift 25 mm Cutter speeds 212 – 2,000 rpm Axial feed rate stepless 0.05 – 4.0 mm/rot. Radial feed rate stepless 0.2 – 200 mm/min. Milling spindle drive 3 kW Total drive approx. 10 kW – 50 Hz – 380 Volt Weight approx. 2,400 kg Accessories / Special equipment: Fully automatic operating cycle and minimal auxiliary times enabled by freely programmable SIEMENS programmable controller S5 for all machining steps, e.g. rapid traverse, feed, cutter on/off, for loading device, tailstock, possible shifting, etc. With piece counter, program numbering, and 30-position digital error display. Pneumatic workpiece loading and unloading device parallel to the workpiece axis for shaft-shaped workpieces approx. 140 mm in length x 8 mm Ø, with pneumatic double gripper for loading and unloading workpieces; raw parts are placed in exchange cassettes outside and then inserted into the loading unit. The double gripper places the parts between the workpiece spindle and tailstock; the tailstock quill pushes the parts into the main spindle collet and clamps them simultaneously. Finished parts are ejected from the main spindle and also returned to the (finished parts) cassette by the gripper. The entire process is electrically monitored and controlled. The complete loading device is enclosed with Plexiglas. Hydraulic workpiece clamping device with collets and hydraulic ejector Separate coolant system with magnetic separator * separate hydraulic unit * various change gears Condition: good – 3 machines available, currently 1 machine ready for demonstration and under power. Machine is set up for cutting worm shafts/armature shafts used in variable transmissions for automotive seat adjusters, window regulators, etc.

Būklė: naudotas, Gamybos metai: 1977, Wheel diameter - max. 400 mm Wheel width 280 mm Module - max. 4 Module - min. 1 Total connected load 15 kW Machine weight approx. 6000 kg Space requirement approx. ... m LORENZ Universal Gear Hobbing Machine Type F 400 Year of manufacture 1977 S/N 8687 _____ Min./max. wheel diameter 400 mm Module range 1 - 4 Number of teeth approx. 8 – 210 Milling width approx. 280 mm Max. workpiece installation length approx. 450 mm Milling slide swiveling up to 60° Cutter size (diameter x length) 160 x 220 mm Cutter shifting max. 180 mm Cutter speeds 125-500 rpm Table diameter x bore 375 x 80 mm Feed range: Fpedpfjt Hw Hxox Ahwed axial 0.31 - 4.00 mm/rev radial 0.12 – 1.60 mm/rev tangential 0.035 – 4.5 mm/min Milling spindle drive approx. 8 kW Total drive power approx. max. 15 kW - 380 V - 50 Hz Weight approx. 6,000 kg Accessories / Special features • Multiple milling programs selectable for climb and conventional milling, as well as for radial/axial milling processes, possibly worm gear milling • Universal milling head with cutter shifting • Hydraulic workpiece clamping on table and hydraulic tailstock • Hydraulically folding counter-holder connection for easier loading • Differential for helical gearing • Infinitely variable speed control, display for speed and amperage • Change gears, various accessories, coolant system * Very robust construction Condition: good – will be demonstrated shortly Delivery: ex stock – as inspected Payment: upon receipt of invoice, strictly net

Būklė: naudotas, Gamybos metai: 1995, Wheel diameter - max. 80 mm Wheel width 120 mm Module - max. 3 Module - min. 1 Control: SIEMENS 840 C Total power requirement: 30 kW Machine weight approx. 7,500 kg Footprint approx. [space missing] m LIEBHERR CNC-controlled gear hobbing machine Type: LC 82 Year of manufacture: 1995 # 0836 --- Wheel diameter max. 80 mm Module 1 – 3 Helix angle +/- 45° Distance table center to tool center: 15 – 160 mm Vertical travel of milling slide: 250 mm Fpodpfst Hw R Djx Ahwjd Shift range/tool traverse: 180 mm Min. number of teeth: 3 Cutter Ø x length approx.: 90 x 200 mm Cutter speeds up to max.: 800 rpm Feeds in axial/radial/tangential: 20/4/5 mm/rev Max. workpiece clamping length: 250 mm Spindle drive approx.: 8 kW Total drive approx.: 30 kW - 400 V – 50 Hz Total weight approx.: 7,500 kg Accessories / Special equipment: • SIEMENS CNC control type 840 C for 6 axes (i.e. cutter drive/Table drive/Swivel angle of the milling head/axial feed/radial feed/tangential feed) with gear-specific user interface and diagnostic functions for rapid troubleshooting. • With device for automatic insertion of the hob into the tooth gap • Automatic shifting of the cutter axis • Automatic workpiece loading unit SSL = quick swivel loader using a mechanical step transmission and cam disk for fast loading times, with 3-way rotary gripper for blank gripping/working position/unloading. Current workpiece size Ø 30 x 120 mm, helical gearing (pinions) • Workpiece feeding by means of plate chain conveyor (PKB) for workpieces with positive-fit carrier. Additional feed belt for raw and finished parts • Chip conveyor, complete working area enclosure, intermediate coolant tank with pump Complete working area enclosure with sliding door and oil mist extraction, etc. The machine can also be used for dry gear cutting. Condition: satisfactory to good – under power and ready for demonstration, compact design! Delivery: ex-stock – as inspected Payment: net cash – on receipt of invoice

Būklė: naudotas, Gamybos metai: 1997, Wheel diameter - max. 215 mm Wheel width 40.65 mm Module - max. Total power requirement 20 kW Machine weight approx. 10 t G L E A S O N (USA) CNC Grinding Machine for Spiral and Hypoid Bevel Gears Model PHOENIX HG 200 Year of construction 1997 Max. external diameter of workpiece: 215 mm Tooth profile size (height x width): 16 mm x 40.65 mm Number of teeth: 5 - 200 Maximum gear ratio: 1 : 10 Grinding wheel diameter: 51-190 mm Grinding wheel speed: 1,000 – 6,000 rpm X-axis (horizontal): 152 mm Y-axis (vertical): 178 mm Z-axis (sliding base): 304 mm Distance machine center to workpiece spindle face: 115 mm Axis speed: 125 mm/sec Workpiece spindle speeds: 0-30 rpm Workpiece spindle bore, tapered: 3 29/32 inches Total drive approx.: 20 kW - 380 V – 50 Hz Weight approx.: 10,000 kg Accessories / Special equipment: • FANUC – 7-axis CNC control type 150 MB with monitor and direct data entry, automatic calculation of all workpiece and grinding parameters • Large, sophisticated coolant system with filtration, band filter, etc. • Powered grinding wheel dressing device with CNC-controlled compensation for wheel form and diameter after each dressing cycle • Gear grinding can be performed either as single part processing with conical cup wheel (Gleason 30°) or with a cylindrical cup wheel. Grinding wheels can be made of CBN or conventional “dressable” aluminium oxide, depending on cost. Grinding with a conical wheel provides advantages in terms of heat management and contact pattern quality. Therefore, these bevel gear sets (automotive industry) can be manufactured in high quality, with consistent accuracy, cost-efficiently, and with short setup times. Please refer to the brochure copy on our website for additional details. Condition : very good – can be demonstrated under power Delivery : ex stock - as inspected Payment : strictly net – upon receipt of invoice We look forward to your order. Further gear manufacturing machines always in stock. X-axis (horizontal): 152 mm Y-axis (vertical): 178 mm Z-axis (sliding base): 304 mm Distance machine center to workpiece spindle face: 115 mm Axis speed: 125 mm/sec Workpiece spindle speeds: 0-30 rpm Workpiece spindle bore, tapered: 3 29/32 inches Total drive approx.: 20 kW - 380 V – 50 Hz Weight approx.: 10,000 kg Fsdpfx Aet Hwxhohwspd Accessories / Special equipment: - FANUC – 7-axis CNC control type 150 MB with monitor and direct data input, automatic calculation of all workpiece and grinding parameters - Large, sophisticated coolant system with filtration, band filter, etc. - Powered grinding wheel dressing unit with CNC dressing control for automatic form and diameter compensation after each dressing - Gear grinding can be performed either as single part processing with a conical cup wheel (Gleason 30°) or with a cylindrical cup wheel. These grinding wheels can be made of CBN or conventional dressable aluminum oxide wheels (cost dependent). Grinding with a conical grinding wheel...

Būklė: naudotas, Gamybos metai: 1980, Wheel diameter - max. 1010 mm Wheel width 0 mm Module - max. Module - min. Total power requirement 15 kW Machine weight approx. 9.5 t Space requirement approx. m G L E A S O N (USA) "CURVIC-Coupling" - Automatic Coupling Grinding Machine Type 120 (888), Year of manufacture 1980 Serial no. 763402 Max. tooth height 10 mm Max. swing diameter of workpiece 1,010 mm Max. outside diameter of CURVIC teeth 610 mm Retraction of workpiece slide plate 216 mm Max. distance grinding wheel to workpiece nose 90-430 mm Max. workpiece weight incl. clamping device approx. 500 kg Number of teeth range 32 - 150 Grinding wheel diameter approx. 152 - 320 mm Fpsdpfxot Hwnij Ahwsd Grinding wheel speed, stepless 0 - 3,600 RPM Workpiece spindle bore 60 mm Total drive power approx. 15 kW - 380 V - 50 Hz Weight approx. 9,500 kg Accessories / Special equipment: Automatic rough grinding and finish grinding by means of presettable counters and integrated feed curves Counter for number of teeth Counter for number of dressing cycles 2 mounted dressers with 3 dressing diamonds for external dressing, internal dressing, and dressing wheel tip Mounted index plate for 48 teeth Separate coolant unit with band filter, separate hydraulic system Freestanding oil mist extraction unit by TRION, various small parts

Būklė: naudotas, Gamybos metai: 1977, Grinding diameter - max. 400 mm Grinding width 0 mm Module - max. Module - min. Total power requirement 3 kW Machine weight approx. 4.2 t Space requirement approx. m Dressing wheel - Ø min./max. 64 - 320 mm Grindable module size 1 - 12 Modul Max. dressing wheel width 40 mm Number of teeth 13 - 240 Roller diameter 73 - 320 mm Fedpfx Ajt Hwnvohwopd Workpiece slide speed 5 - 20 - 30 - 40 teeth/minute Grinding wheel speed 690 rpm Grinding wheel diameter 762 mm Grinding wheel swivel (contact angle) 5-21° Grinding slide swivel (helix angle) 2x 35° Grinding slide vertical adjustment 240 mm Dresser speed 1/0.5/0.25 m/minute Grinding spindle drive / total drive 1.1 / 3 kW - 380 V - 50 Hz Weight approx. 4,200 kg Accessories / Special equipment: The machine is suitable for grinding external and internal rack wheels as well as for grinding master gears or cutter wheels for gear shaping machines. Unfortunately, no further accessories are available for the machine, so it is an investment as a secondary machine if suitable accessories are already available.

Būklė: naudotas, Gamybos metai: 1992, Wheel diameter – max. 150 mm Wheel width 300 mm Module – max. 4.5 Module – min. (not specified) Total power requirement 20 kW Machine weight approx. 6 t Space requirement approx. (not specified) CNC-controlled horizontal hobbing machine with workpiece portal loader, model A 35 / 36 CNC, year of manufacture 1992 Workpiece diameter / wheel diameter with automatic loading max. 150 mm Workpiece diameter with manual loading max. 200 mm Max. workpiece length approx. 400 mm Axial milling length (Z axis) 300 mm Module range for HSS/Carbide cutters 3 / 4.5 mm Number of teeth min./max. 2–999 Fedst Hwxbopfx Ahwopd Centre distance tool–workpiece min./max. 0–190 mm Workpiece rotation speed max. 0–350 rpm Milling slide swiveling left/right 50 / 60° Cutter size Ø x length 102 x 230 mm Cutter shift max. (Y axis) 100 mm Radial slide travel max. (X axis) 10–150 mm Tailstock travel max. (W axis) 420 mm Cutter speed stepless 0–1,500 rpm Feed range on all axes steplessly adjustable 3.5 or 4 m/min Spindle drive approx. 8.8 kW Total power approx. 20 kW – 220 V/400 V / 50 Hz Weight approx. 6,000 kg Accessories / Special Equipment: MIKRON CNC control type 788 (BWO) with monitor for a total of 8 axes (ABC and WYZ and WV) with conversational programming for creating various gearing cycles, such as helical gearing, worm and worm wheel gearing, crowned gears, with and without shifting, as well as further subprograms. Heavy duty shifting milling head with high cutter speeds and long shifting path, also for 2 cutters, with quick-change system and hydraulic counterbearing. Workpiece spindle head (C) with quick-change system (collet chuck) Heavy tailstock with 420 mm travel (W), in combination with an automatic workpiece loading device from GÜDEL Switzerland with a linear portal loader (approx. 1000 mm stroke (V)), swiveling double gripper with jaws for loading and unloading shaft-shaped workpieces (currently approx. 60 mm length x 25 mm Ø x module 1.5), however, without workpiece storage device. Separate coolant unit with magnetic chip conveyor Enclosed full machine guarding with sliding doors 2 machines with workpiece marking devices by BORRIES, unfortunately otherwise without accessories.

Būklė: geras (naudotas), Gamybos metai: 1984, Wheel diameter – max. 400 mm Wheel width 275 mm Fjdpfx Asv T Nqashwjpd Module – max. 6 Machine weight approx. 5.5 t Change gears and milling accessories

Būklė: naudotas, Gamybos metai: 1998, Workpiece diameter with 1:10 transmission: 300 mm Workpiece diameter with 1:1 transmission: 212 mm Fpsdpsul El Tefx Ahwsd Number of teeth – max.: 200 Number of teeth – min.: 6 X-axis travel: 300 mm X-axis speed: 0.1–5,000 mm/sec Y-axis travel: 400 mm Y-axis speed: 0.1–5,000 mm/sec A-axis: -170° / +170° Control: Siemens Sinumerik 840 C Total power requirement: 38 kW Machine weight approx.: 10 t Space requirement approx.: 4.20 x 2.20 x 2.10 m

Būklė: geras (naudotas), Gamybos metai: 1972, Ratų skersmuo – maks. 80 mm Ratų plotis 60 mm Modulis – maks. 3 Modulis – min. 0,1 Bendras galios poreikis 0,4 kW Mašinos svoris apie 120 kg Fpedpfx Aow N S D Sjhwod Reikalinga erdvė apie 0,6x0,6x0,75 m Mašina skirta nedidelių kūginių / tiesių krumpliaračių šlifavimui. Kūginių krumpliaračių frezavimui naudojama Mikron 102.01.

Būklė: geras (naudotas), Gamybos metai: 1991, Machine weight approx. 6 t The base machine design is characterized by the following features: - Horizontal orientation of the workpiece spindle; vertical orientation of the milling spindle or milling head - Workpiece clamping is between the workpiece spindle head (left) and the tailstock (right) - The radial slide is mounted on the machine base (X-axis) - The axial slide travels on the radial slide (Z-axis) - The shift milling head is equipped with automatic angular adjustment (A-axis); the shift slide (Y-axis) moves tangentially to the workpiece diameter - CNC controlled - IBH control system - Loading device - Extensive accessories Technical specifications: - Maximum module for gear hobbing with hobs according to DIN 8002: 4.5 mm - Maximum module for high-performance milling: 3.0 mm Fpjdpoub Amfsfx Ahwsd - Number of teeth: 2 - 999 - Maximum workpiece diameter with manual loading: 200 mm - Maximum workpiece diameter with automatic loading: 150 mm - Maximum workpiece length: 400 mm - Maximum / minimum cutter diameter: 102/40 mm - Maximum cutter length: 230 mm - Maximum / minimum cutter arbor diameter (standard): 32/16 mm - Axial slide travel = maximum milling length, Z-axis: 300 mm - Radial slide travel, X-axis: 140 mm - Cutter traverse (shift travel) Y-axis: 100 mm - Tailstock travel W-axis: 420 mm - Swivel angle shift milling head (left/right) A-axis: 50°/60° Milling coordinates: - Z-axis: 100 - 400 mm - X-axis: 100 - 150 mm - Y-axis (milling spindle face): 50 - 230 mm - W-axis (tailstock spindle face): 165 - 585 mm - Cutter speed range, standard B-axis: 0 - 1500 rpm - Workpiece speed, C-axis: 0 - 350 rpm Feed rates: - X-axis: 3500 mm/min - Z-axis: 3500 mm/min - Y-axis: 4000 mm/min - W-axis: 5500 mm/min - V-axis (portal loader): 80,000 mm/min

Būklė: geras (naudotas), Wheel diameter – max. 630 mm Wheel width 375 mm Module – max. 10 Clamping table 550 mm Table bore 125 mm Infinitely variable cutter speeds 62 – 390 rpm Taper MORSE 5 Axial feed 0.40 – 6.80 mm/rev Radial feed 0.10 – 1.76 mm/rev Distance from milling spindle to clamping spindle 50 – 425 mm Minimum number of teeth 8 Cutter diameter x width 192 / 215 mm Cutter shift 200 mm Main drive motor 7.5 kW Total power requirement 21 kVa Fjdpfeua It Uox Ahwjpd Machine weight approx. 8.2 t Machine equipment: - Universal milling head with tangential adjustment - Pressure reducing valve for counterstay - Magnetic chip conveyor - Year of manufacture approx. 1976

Būklė: naudotas, Gamybos metai: 1989, Wheel diameter – max. 400 mm Wheel width: 275 mm Module – max. 6 Machine dimensions: 300 x 330 x 245 cm Machine weight: approx. 5.5 t Specification: Maximum wheel diameter: 400 mm Fpodpfx Ahou A I Elowsd Min. module: 1 Max. module: 6 Table diameter: 370 mm Maximum wheel diameter: - with counter support: 340 mm - without counter support: 400 mm Max. axial offset: 275 mm Max. tangential adjustment: 100 mm Tooth helix angle: 45 degrees Maximum cutter diameter: 145 mm Maximum hob length: 170 mm Hob spindle speed range: 63–180 rpm Steplessly adjustable axial feed: 0.2–10 mm/rev Steplessly adjustable tangential feed: 0.1–5 mm/rev Radial feed for spur gears: 0.1–4 mm/rev Radial feed for worm gears: 0.025–1 mm/rev Rapid traverse axial: 500 mm/min Rapid traverse tangential: 250 mm/min Radial rapid traverse for spur gears: 400 mm/rev Radial rapid traverse for worm gears: 100 mm/rev Motor power: 7.4 kW

Būklė: naudotas, Gamybos metai: 1969, Wheel diameter - max. 160 mm Wheel width 355 mm Module - max. 4.5 Module - min. 0.5 Centre distance 450 mm Fjdpfjvz Ec Iex Ahwjpd Total power requirement 11 kW Machine weight approx. 3.8 t Space requirement approx. 2x1.7x1.6 m Wheel diameter - max. 160/175 mm Wheel width 355 mm Module - max. 4.5 Spindle bore 75 mm Centre distance 410 mm Number of teeth - min. 2, 3 Cutter diameter max. 115 mm Cutter length max. 105 mm Centre distance between cutter and workpiece - max. 138 mm Centre distance between cutter and workpiece - min. 30 mm Milling head - swivelling 120° Cutter speeds 70 - 400 rpm Axial feeds 0.25 - 4.0 mm/rev Radial feeds 0.09 - 1.5 mm/rev Total power requirement approx. 9.5 kW Machine weight approx. 3.5 t Space requirement approx. 1730x1400x1440 mm Equipment/accessories: - Change gears - Milling arbors - Clamping devices - Documentation

Gamybos metai: 1993, būklė: paruoštas naudoti (naudotas), Automatische Schleifmaschine VIET Modell Rita 4C EL Festes Tischband, bewegliche Aggregate Arbeitsbreite: 1350 mm Arbeitshöhe: 4–160 mm Nr. 03 Absaughauben, Durchmesser 150 mm Transportbandgeschwindigkeit: 6–20 m/min mit 3 kW Frequenzumrichter Bürste zur Teppichreinigung in der Haube, Durchmesser 120 mm Ausstattung: 1. Querpolieraggregat Mod. TET 60, elektronisch gesteuertes Pad mit 60 Sektoren Lamellenband: 6150 x 140 mm Eigenes Schleifmittel: 8350 x 170 mm Bandgeschwindigkeit: 5,6–26,2 m/s Frequenzumrichter: 15 kW Drei Absaughauben, Durchmesser 140 mm 2. Walzenschleifaggregat Mod. R320 – 40, Gummibeschichtung 40° Shore Schleifband: 3250 x 1400 mm Fodpfsltlx Tjx Ahwjpd Geschwindigkeit: 1,5–12,5 m/s Frequenzumrichter: 15 kW Bandreinigungsgebläse Zwei Absaughauben mit 140 mm Durchmesser, eine mit 200 mm Durchmesser 3. Polieraggregat (Puffer) Mod. TE 60, elektronisch gesteuertes Pad mit 60 Sektoren Schleifband: 3250 x 1400 mm Geschwindigkeit: 2,9–14,1 m/s Frequenzumrichter: 15 kW Bandreinigungsgebläse Zwei Absaughauben mit 140 mm Durchmesser, eine mit 200 mm Durchmesser 4. Querschleifaggregat Mod. TET 60, elektronisch gesteuertes Pad mit 60 Sektoren Lamellenband: 6150 x 140 mm Eigenes Schleifmittel: 8350 x 170 mm Bandgeschwindigkeit: 5,6–26,2 m/s Frequenzumrichter: 15 kW Drei Absaughauben, Durchmesser 140 mm 5. Scotch-Brite-Aggregat Motorleistung: 0,55 kW Absaughaube Durchmesser 140 mm 6. Bürstenaggregat Motorleistung: 0,55 kW Absaughaube Durchmesser 140 mm 7. Plattenreinigungs-Rotorgebläse-Aggregat

Būklė: geras (naudotas), Gamybos metai: 2007, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 986003, šlifavimo rato greitis: 6 000 aps./min, įrankio skersmuo: 230 mm, X ašies eiga: 325 mm, Y ašies eiga: 350 mm, Z ašies eigos atstumas: 470 mm, TECHNICAL DETAILS Maximum transmission ratio: 10:1 Number of teeth: 3 - 200 Tooth height: 20 mm Maximum tooth width: 58 mm Control system: SIN 840 D SIEMENS Axes X-axis: 325 mm Y-axis: 350 mm Z-axis: 470 mm Fodpfev Rcn Hsx Ahwjpd B-axis: +90.1° / -1° Spindle Grinding spindle speed: stepless up to 6,000 rpm Workpiece spindle speed: 1,200 rpm Tooling Maximum tool diameter: 230 mm Minimum tool diameter: 69.85 mm Table diameter: 212.71 mm MACHINE DETAILS Total connected load: 75 kW Machine weight: approx. 10,000 kg Required floor space: approx. 6.10 m x 4.40 m x 3.30 m Transport dimensions machine: 4 x 2.5 x 2.85 m / 11 t Transport dimensions coolant tank: 3.55 x 2.41 x 2.5 m / 1.8 t Transport dimensions cooler: 1.5 x 0.8 x 1.1 m / 0.2 t Transport dimensions sheet metal: 2.5 x 1.1 x 0.8 m / 0.25 t EQUIPMENT - Coolant filtration unit Hoffmann HSF 100 V

Būklė: naudotas, Gamybos metai: 2002, Wheel diameter - max. 275 mm Module - max. 6 Module - min. 1.5 Control system: SINUMERIK 840 C Gear width: 5.5 mm Helix angle min. 0° / max. 60° Number of teeth - max. 120 Number of teeth - min. 5 Gear ratio max. 1:10 Fjdpfx Ahevxwnwswjpd Gear ratio min. 1:1 Workpiece spindle speed max. 110 rpm Cutter head speeds: 20 - 110 rpm Total connected load: 100 kW Machine weight approx. 16.7 t Space requirement approx. 5.20 x 2.30 x 2.40 m Integrated deburring unit, U-axis / Q-spindle Chip conveyor Coolant system Electrostatic air cleaner: ELBARON No tools included No workpiece clamping device

Būklė: naudotas, Gamybos metai: 2006, Maximum transmission ratio: 10:1 Number of teeth - min. 3 Number of teeth - max. 200 Tooth height: 20 mm Max. tooth width: 58 mm Continuously variable grinding spindle speed: 6,000 rpm Workpiece spindle speed: 1,200 rpm Max. tool diameter: 230 mm Min. tool diameter: 69.85 mm X-axis: 325 mm Y-axis: 350 mm Z-axis: 470 mm B-axis: +90.1 / -1° Workpiece table - Ø 212.71 mm CNC control: SINUMERIK 840 D SIEMENS Total power requirement: 75 kW Machine weight: approx. 10,000 kg Fjdsvxwr Aspfx Ahwspd Space requirement: approx. 6.10 x 4.40 x 3.30 m Coolant filtration system: Hoffmann HSF 100 V

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 2002, Funkcionalumas: visiškai funkcionalus, veleno greitis (maks.): 110 aps./min, ratlankio skersmuo: 275 mm, TECHNICAL DETAILS Max. Wheel Diameter: 275 mm Module Range: min. 1.5 / max. 6 Face Width: 5.5 mm Spiral Angle: min. 0° / max. 60° Number of Teeth: min. 5 / max. 120 Gear Ratio: min. 1:1 / max. 1:10 Drive & Control Control System: SINUMERIK 840 C Max. Workpiece Spindle Speed: 110 rpm Fpsdpfjv Rc Srjx Ahwod Cutter Head Speeds: 20 – 110 rpm Total Power Requirement: 100 kW Machine Weight & Dimensions Machine Weight: approx. 16.7 t Space Requirement: approx. 5,200 x 2,300 x 2,400 mm EQUIPMENT - Deburring device U-axis / Q-spindle - Chip conveyor - Coolant system - Electrostatic Air Cleaner ELBARON - No tools and no workpiece clamping device included

Gamybos metai: 1972, būklė: naudotas, max. pulling force: 10 t max. stroke: 1,250 mm max. cutting speed: 10 m/min max. return speed: 25 m/min broaching stations: 3 passage width: 470 mm distance between broaching stations: 125 mm table: 400 x 400 mm special features: chip removal via permanent magnet chip conveyor Fedecdtnhepfx Ahwepd 1 hydraulic system, 1 working platform, electric-hydraulic shank and end piece holder lock, automatic loading device

Gamybos metai: 1987, būklė: naudotas, mašinos/transporto priemonės numeris: 34, max. traction force: 10 t max. stroke: 1000 mm Fpsdsnd Dmopfx Ahwsd Cutting speed: 7.5 m/min Return speed: 24 m/min Weight: 6.2 t Machine is suitable for tube clearing

Būklė: geras (naudotas), Hoza EMU Punching Machine Fsdpsuzhmtofx Ahwjpd This machine is ideal for punching small shaped parts from paper, rubber, or textile materials. It features high punching force and fits on any sturdy table. The cutting process is initiated via a two-hand safety control system. Forged dies or steel rule dies can be used with the machine. Die stroke: 30 mm Maximum punching format: 150 x 100 mm Weight: approx. 150 kg Color: hammer blue Dimensions: 450 x 360 x 600 mm You can find more items in different sizes — new and used — in our shop! International shipping rates on request!

Būklė: naudotas, Modul KF 250 HSC kūginė krumpliaračių frezavimo staklė sukurta kaip universali mašina lankščiam krumpliaračių apdirbimui ir yra naudojama krumpliaračių bei pavarų gamintojų kūginių krumpliaračių frezavimui. Fpjdoxz Eg Aspfx Ahwod Techniniai duomenys: Ratų skersmuo: 300 mm Modulis - maks.: 10 Danties plotis: 60 mm Užimamas plotas apie: 4,2 x 2,6 x 2,2 m Staklių svoris apie: 11.000 kg *Nuotraukoje parodyta staklė dabartinėje, naudotoje būsenoje; pageidaujant galima dalinė modernizacija arba visiška atnaujinimas (retrofit) su nauja CNC valdymo sistema (SIEMENS ONE).

Būklė: naudotas, Kūginė krumpliaračių frezavimo staklė Samputensili S 500 B suprojektuota kaip universali staklė, pritaikyta lankščiam krumpliaračių apdirbimui. Ji naudojama krumpliaračių ir transmisijų technologijų gamintojų kūginių krumpliaračių frezavimui. Techniniai duomenys: Fedpfx Ahsxz Ef Sowjpd Ratų skersmuo: 500 mm Maksimalus modulis: 5 Danties plotis: 100 mm Apytikris užimamas plotas: 4,5 x 3,2 x 2,4 m Staklių svoris: apie 13 000 kg *Nuotraukoje staklės matomos dabartinėje naudotoje būklėje; pageidaujant, gali būti siūlomos dalinai modernizuotos arba pilnai atnaujintos (retrofit) su nauja CNC valdymo sistema (SIEMENS ONE).

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 1970, Krumplysavimo staklės ZFWZ 6300x40 Gamintojas: WMW-MODUL Modelis: ZFWZ 6300x40/1 Pagaminimo metai: 1970 Didžiausias ratų skersmuo: 7100 mm Krumplių plotis: 1500 mm Didžiausias modulis: 45 Stalo skersmuo: 5300 mm Frezuotuvo skersmuo x plotis: 400x500 mm Didžiausias spiralinio kampas: 45 laipsniai Frezuotuvo skersmuo: 500 mm Fpjdpfexln Iwsx Ahwod Frezuotuvo apsukos: 9-63 aps./min. Bendras galios poreikis: 47 kW Staklių svoris: 160 t Komplektuojama su standartine frezavimo galva, tangentiniu krumpliaračiu, vidaus frezavimo galva, keičiamais krumpliaračiais, atramomis. Galimas vaizdo įrašas.