Kellenberger 1500U Bema Advance pirkti naudotą (3 116)

Būklė: naudotas, Gamybos metai: 2002, Grinding diameter: 450 mm Grinding length: 1500 mm Centre height: 225 mm Control system: FAGOR EQUIPMENT -T1: 500 mm grinding wheel diameter -T2: 400 mm grinding wheel diameter -T6: internal grinding attachment -T7: internal grinding attachment -Spindle motor, water-cooled, 9.8 kW -Marposs tool measurement system -Active longitudinal positioning -Kel-Set -GAP control on T1 and T2 by ELASO (contactless), integrated into the control interface -GAP control on T3/T4 via fluid sensor -Semi-automatic balancing by ELASO, integrated into the control interface for T1/T2 -Tailstock, hydraulic with fine adjustment +/-150 µm -Dressing device on the lower table, workpiece spindle side -Dressing device on the lower table, tailstock side -Dressing device on the upper table -New, service- and operator-friendly enclosure SPECIAL EQUIPMENT: Workpiece headstock with direct drive *highly recommended for non-circular grinding *max. workpiece weight, between centers: 150 kg *max. workpiece weight, overhung: 75 kg *water-cooled *Morse taper 5 combined with short taper mount to DIN 55026 *spindle orientation stop *fixed lower section B-axis with direct drive, center height 225 mm *extremely torsion-resistant Nwsdpeuxfu Nsfx Abzeh *high positional accuracy *resolution ° *water-cooled MECHANICAL OVERHAUL: - Complete machine overhauled according to Kellenberger measurement protocol - New paintwork New hydraulic unit: - Improved temperature control (oil cooler) - Energy-saving: only one pump, and not running continuously! - Pressure monitoring - Monitoring of water content in the hydrostatic oil (early detection of bellows damage) Hydrostatic screw drive in X axis - Wear-free, since no contact during operation - No loss of accuracy, even during prolonged operation under full load at maximum speed - Friction-free at low speeds - No reversal jump of friction force when changing direction - Transmits smallest rotational movements - No stick-slip effect even at low speeds - No fluctuation in friction torque due to recirculating balls - Higher axial stiffness than ball screw drives - Significantly better damping, leading to improved workpiece surface and longer tool life - No vibrations due to recirculating balls - Also suitable for high speeds and accelerations - Cost-effective alternative to linear motors, offering higher accuracy and much less heating - Much lower power loss and thus no swarf issues on permanent magnets - Much lower cooling requirements compared to linear motors ELECTRICAL OVERHAUL: -New, modern CNC cylindrical grinding machine control with BEMA cylindrical grinding interface -Newly constructed control cabinet -New drive technology -Replacement of all electrical wiring (Berus pressure switches etc.) -New absolute glass scales in X and Z -New absolute encoder (for B-Axis) CONTROL SYSTEM: The grinding software consists of a base license and various options, depending on the machine configuration. Software base functions: - External and internal oscillation grinding - External and internal plunge grinding - External and internal plane oscillation grinding - External and internal plane plunge grinding - External and internal cone oscillation grinding - External and internal radius grinding (radius dressed on wheel) - Semi-automatic oscillation grinding - Workpiece...

Būklė: naudotas, Grinding diameter: 250 mm Grinding length: 1000 mm Centre height: 125 mm Grinding wheel diameter: 500 mm Grinding wheel width: 80 (100) mm Bore: 203.2 mm Workpiece spindle taper: MK5 Workpiece spindle speed: 20–400 rpm Workpiece headstock swiveling: +/- 360° Grinding spindle headstock swiveling: +/- 0° Infeed (incremental): 0–9.99 mm/Ø Infeed (continuous): 0–9.99 mm/Ø Table swivel: +/- 10° Table speed: 0.02–6 m/min Workpiece weight between centres: 130 kg Max. workpiece weight (overhung): 130 kg incl. clamping Cross traverse: 270 mm Tailstock quill taper: MK3 Quill stroke: 30 mm Total power requirement: 5.5–7.5 kW Machine weight approx.: 2.7 t As a global leader in the field of Kellenberger overhauls/retrofits, we are not only able to deliver machines in as-new condition with warranty, but can also offer you service for your machines. Geometrically overhauled and newly painted according to Kellenberger measurement protocol. Completely new electrics with new infeed control. Photos show a previously delivered machine of the same design, but with 1500 mm centre distance and universal grinding head instead of the 500 mm wheel head, purely for external cylindrical grinding purposes. Equipment: - 2-axis digital readout - New DGS paper band filter Optional at extra charge: - Semi-automatic dressing - Dressing size compensation - GAP Control - Measuring automation - Safety doors Electronically controlled infeed system with stepper motor drive. Hydraulic table longitudinal and rapid traverse movement. Powerful, non-swiveling grinding spindle headstock for production external cylindrical grinding operations. Areas of application: Machining of high-precision components in the gearbox, machine tool, and general mechanical engineering sectors. Pair grinding for the hydraulics industry. Nsdpfx Aod Ih Egsbzswh At present, the machine tool does not meet the basic safety and protection requirements such as those specified in BetrSichV 2015. The required minimum safety objective must be determined by means of a risk assessment according to BetrSichV.

Būklė: naudotas, Gamybos metai: 1982, Grinding diameter 630 mm Grinding length 600 mm Centre height 320 mm The machine was overhauled according to the Kellenberger inspection protocol and newly repainted. The prone-to-failure Güttinger control system was replaced with the modern BEMA X control system. This means the machine also received a completely new electrical system as part of this upgrade. Machine equipped with a reinforced workpiece spindle head for chuck grinding of heavy workpieces. Currently, the machine does not meet the fundamental safety and protection requirements specified in the German Ordinance on Industrial Safety and Health (BetrSichV 2015). Nedpfx Abjvq R Uzjzjwh Raising the required minimum safety standard must be determined by means of a risk assessment according to BetrSichV.

Būklė: naudotas, Gamybos metai: 1982, Grinding diameter 630 mm Grinding length 600 mm Centre height 320 mm Nwedpfxjv Dxxze Abzoh Machine equipped with reinforced workpiece headstock for unsupported grinding of heavy workpieces. The machine will undergo a major service/partial overhaul including a geometry inspection report in accordance with Kellenberger new machine standards. The machine tool currently does not meet the essential safety and protection requirements as specified in the German Ordinance on Industrial Safety and Health (BetrSichV 2015). The necessary minimum safety objectives must be determined in the course of a risk assessment in accordance with BetrSichV.

Būklė: naudotas, Gamybos metai: 2010, Grinding diameter 350 mm Grinding length 1000 mm Centre height 175 mm Control unit: Fanuc 310is Nsdpfxjvdk N Eo Abzswh Completely mechanically overhauled. Includes grinding process setup and tooling for one part. Original photo of the machine from EMO 2010. CNC control: GE Fanuc 310is Hand panel for CNC control: GE Fanuc With Wenger loader Rotary part with automatic 1° indexing Grinding head UR 1-2-3 Grinding wheel configuration left: 500 x 80 mm Grinding wheel configuration right: 400 x 63 mm Operating unit for a high-frequency internal grinding spindle MFV / MFZ High-frequency internal grinding spindle MFN 1090 Coolant supply through the workpiece spindle Dressing device on the upper table Swiveling holder for PCD diamond plates Base module for KEL-TOUCH contact sensor and KEL-BALANCE balancing units KEL-TOUCH contact sensor for universal grinding head variants R / RS / UR / URS KEL-TOUCH at the workpiece spindle headstock for internal and external grinding Preparation for measuring control systems Movomatic ESZ 400 or Marposs P7 ME Preparation for external filtration unit Coolant cut-off for table devices Fully enclosed emulsion Mist extraction unit for emulsion Maintenance unit for pneumatic auxiliary functions Preparation for KEL-VITA gantry loader KEL-POS, MOVOMATIC: probe C25 Hydraulic preinstallation for Arobo steady rest

Būklė: naudotas, Gamybos metai: 2006, Grinding diameter 350 mm Grinding length 1000 mm Centre height 175 mm Machine weight approx. 3.5 t Machine fully overhauled in BEMA style with 12 months warranty Mechanically and visually as new Nsdpfx Abjt Ii Nbszjwh Photo shows a freshly completed machine with some different options. Fanuc 21i control - Grinding head UR 1-2-3 for external/internal/planar grinding - B-axis automatic 1° Hirth toothing - Active longitudinal positioning KEL-POS Movomatic - Semi-automatic balancing device KEL-BALANCE - Left grinding wheel mount 400mm diameter - Right grinding wheel mount 300mm diameter - Internal grinding attachment with belt drive - Tailstock with micrometric adjustment - Fine adjustment of upper table - Paper band filter SBP4 240l

Būklė: naudotas, Grinding diameter 350 mm Grinding length 1500 mm Centre height 175 mm Left wheel 600 mm Grinding spindle head fixed, non-rotatable. Nodpfjt Ii Rfjx Abzjwh Equipped with new FAGOR control system featuring BEMA cylindrical grinding interface. With new service-friendly enclosure. Completely overhauled according to Kellenberger measurement protocol.

Būklė: naudotas, Gamybos metai: 1995, Šlifavimo skersmuo: 350 mm Šlifavimo ilgis: 1000 mm Centų aukštis: 175 mm 2013 m. kapitaliai suremontuota Sustiprinta ruošinio špindelio galva Nuolat reguliuojama B ašis Griebtuvas Be nuotraukoje matomo pradžios ir lunetos Valdymas: Kelco 90 Mašiną galima apžiūrėti pas klientą prijungtą prie elektros iki 2026 m. sausio mėn. imtinai. Njdpsxyadajfx Abzowh

Būklė: paruoštas naudoti (naudotas), Siūloma Kellenberger išorinė apvalaus šlifavimo staklė. Atstumas tarp centrų: 1000 mm, centrų aukštis: 175 mm, didžiausias ruošinio skersmuo: 250 mm, X/Z eiga: 1000 mm/220 mm, šlifavimo disko skersmuo: 500 mm, apsukos: 1530 aps./min. Staklių matmenys (X/Y/Z): apie 3000 mm/1850 mm/1750 mm, svoris: apie 3150 kg. Galima apžiūra vietoje. Nwedjxxzi Ijpfx Abzeh

Būklė: paruoštas naudoti (naudotas), An older precision cylindrical grinding machine from Kellenberger, including accessories, is available. Centre distance: 200 mm, centre height: 125 mm, maximum workpiece weight: 3 kg, maximum workpiece diameter: 245 mm, maximum workpiece length: 130 mm. An on-site inspection is possible. Nwedow Edpgopfx Abzeh

Gamybos metai: 1979, būklė: visiškai atnaujintas (naudotas), Funkcionalumas: visiškai funkcionalus, TECHNICAL DETAILS Centre height: 125 mm, plus heights of 50 mm Distance between centres: 1,000 mm Grinding wheel: • Diameter: 400 mm • Width: 50 mm • Bore: 127.0 mm Swivel angle: 270° Workpiece spindle head speed: 20 - 400 rpm Spindle taper: 5 MT Tailstock taper: 3 MT Table swivel angle: 8° Table feed rate: stepless up to 6.0 m/min Internal grinding spindle with 60,000 rpm External grinding wheel motor: 4.0 kW Workpiece spindle motor: 1.5 kW Machine weight: 3,100 kg Overall machine dimensions: 2,860 × 1,680 × 1,670 mm (L × W × H) EQUIPMENT & SCOPE OF DELIVERY • Machine fully retrofitted • New control cabinet & new wiring diagram • New motor & frequency inverter for workhead • 2-axis DRO • Coolant tank with paper filtration • Geometry manufactured according to Kellenberger protocol Njdpfxek H Hp Ne Abzewh • Internal grinding spindle • Extensive accessories Please refer to the attached inspection report for further machine details.

Būklė: naudotas, Gamybos metai: 1995, Vamzdžio skersmuo: 45 mm Sienelės storis: 2 mm Minimalus lenkimo spindulys: . mm Mašinos svoris apie 1,7 t Užimama vieta apie 5x0,85x1,5 m sn 1765 Vamzdžio ilgis iki 4100 mm Techniniai duomenys pateikti gamintojo arba operatoriaus ir nėra mums įpareigojantys. Pasiliekame teisę pertraukti pardavimą; galioja tik mūsų verslo ir pardavimo sąlygos. Nedpfjyutr Usx Abzewh Apie mus: daugiau nei 400 nuosavų mašinų sandėlyje daugiau nei 15.000 m² sandėlio ploto, krano keliamoji galia 70 t daugiau nei 10.000 priedų jūsų dirbtuvėms Jei norite parduoti mašinas, gamybos linijas ar įmonę, susisiekite su mumis. Daugiau pasiūlymų rasite mūsų internetiniame puslapyje. Peržiūra galima suderinus laiką. Laukiame jūsų apsilankymo. Jūsų Markus Hirsch komanda

Būklė: geras (naudotas), Funkcionalumas: visiškai funkcionalus, Parduodama naudota Kellenberger apvalaus šlifavimo staklė labai geros būklės. Kaina ženkliai sumažinta !!!!! Nwedpfxow Dzbde Abzoh

Būklė: labai geros būklės (naudotas), Kellenberger 1000U apvali šlifavimo staklės su daug priedų parduodamos už patrauklią kainą. Šios staklės yra labai geros būklės ir visiškai veikiančios. 2019 metais pirktos po kapitalinio remonto. Kaina ženkliai sumažinta! Nwedpfxswkt Eus Abzjh

Būklė: naudotas, Funkcionalumas: visiškai funkcionalus, Kellenberger apvalių paviršių šlifavimo staklės labai geros būklės. Parduodamos už palankią kainą. Kaina ženkliai sumažinta !!!!! Nwedew Dy Rqjpfx Abzoh

Būklė: geras (naudotas), cilindrinės šlifavimo staklės Nwsdpfjtrguksx Abzsh

Būklė: naujas, In this offer, you are purchasing a new color multifunction system "Canon imageRUNNER Advance DX C3822i" Item for sale: 1 x Canon imageRUNNER DX C3822i with the following features: Nwodpfx Aoi Hchtsbzsh incl. original document feeder incl. lower cabinet for consumables Various images show special equipment that is not part of this listing Condition: This offer is for a new device, which is packed in the original carton. The images are sample photos. Packaging and Shipping: You are welcome to view the device during our business hours. Please arrange an appointment for this! Seaworthy packaging and worldwide shipping available on request! For further information, you are of course welcome to contact us directly.

Būklė: geras (naudotas), Distance between centers: 1000 mm Center height: 230 mm Nsdpjtrgnzefx Abzewh Main motor power: 9.2 kW Grinding wheel dimensions (od x id x width): 500x80x203.2 mm Max grinding diameter: 460 mm Tailstock taper: MORSE 4 Workhead taper: MORSE 5 Max. Z-axis travel: 1115 mm Max. X-axis travel: 260 mm Approx. dimensions (length x width): 440x370 cm Approx. weight: 4700 kg

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 1995, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 630005, centro aukštis: 305 mm, plotis centre: 1 000 mm, X ašies eiga: 350 mm, Z ašies eigos atstumas: 1 160 mm, valdiklio modelis: KELCO 90, TECHNICAL DETAILS Centre Height: 225 mm / 305 mm Centre Distance: 1,000 mm Z-Axis Travel: 1,160 mm X-Axis Travel: 350 mm Max. Workpiece Weight: 200 kg Workpiece Diameter: 449 mm Left Grinding Wheel Diameter: 500 mm Left Grinding Wheel Width: 80 mm Left Grinding Wheel Bore: 203 mm Right Grinding Wheel Diameter: 400 mm Right Grinding Wheel Width: 40 mm Right Grinding Wheel Bore: 127 mm B-Axis Swivel Range: +30° / -190° Max. Grinding Wheel Speed: 1,720 rpm Peripheral Speed: 45 m/s Workpiece Spindle Speeds From: 5 rpm Workpiece Spindle Speeds Up To: 500 rpm Spindle Taper: MK 5 Tailstock Quill Mount: 4 Morse Taper Tailstock Quill Travel: 50 mm X-Axis Feed: 8 m/min Z-Axis Feed: 16 m/min Max. Table Swivel: -1° / +11° MACHINE DETAILS Control: KELCO 90 Nsdpfx Aboyhnrvezjwh Total Power Requirement: 25 kW Connection: 50 Hz, 3x 380 Volt Dimensions & Weight Machine Dimensions (L x W x H): 2,850 x 2,200 x 2,100 mm Control Dimensions (L x W x H): 550 x 450 x 900 mm Machine Weight: approx. 6,000 kg EQUIPMENT - 80 mm Raise / Height Extension - Coolant System - Automatic Tool Measurement KELSET - Dressing Device - Internal Grinding Attachment (without spindle) - Set of Flanges - Set of Grinding Wheels - Balancing Arbor - Lamp - Magnetic Chuck Diameter (2x): 300 mm / 500 mm - Electronic Hand Control Panel

Būklė: visiškai atnaujintas (naudotas), Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 1315/451, Completely overhauled: Mechanics, geometry, hydraulics, and electrical components (checked and/or replaced) Grinding wheel headstock Disassembly, cleaning of parts, replacement of worn and defective parts, motor overhaul, bearing replacement, belt replacement, spindle disassembly, replacement of seals and O-rings + adjustment. Newly painted. Workpiece headstock Disassembly, cleaning of parts, replacement of worn and defective parts, motor overhaul, belt replacement. New spindle bearings. Newly painted. Tailstock Disassembled, inspected, overhauled. Hydraulics Disassembled, motor check, replacement of hoses, defective and worn parts. Hydraulic block inspected. X Axis Disassembly, replacement of worn parts such as O-rings, seals, rings, etc., overhaul of hydraulic piston, grinding of tables. Z Axis Disassembly, grinding of tables, replacement of worn and defective parts, hydraulic piston overhaul, newly painted. Electrical cabinet Complete inspection, various relays replaced. Painting Colors: White RAL 9003 and Grey RAL 7011 Geometry according to manufacturer’s protocol. Inspection and cleaning of various accessories. Origin CH Voltage 380 / 50 / 3 Net weight approx. 2200 kg Customs tariff number 8460.2920 TECHNICAL SPECIFICATIONS Nominal centre distance 600 mm Max. centre distance (extended headstock) 750 mm Centre height, standard 125 mm Centre height with interchangeable shoes for headstocks 175 to 250 mm Max. workpiece diameter (125 mm centre height) 250 mm Max. workpiece diameter with interchangeable shoes 350 to 500 mm Table swivelling in either direction 10° Max. length for surface grinding (max. width = 200 mm) 900 mm Table speed with continuously variable hydraulic control up to approx. 6 m/min Table reversal dwell time 0-5 sec. Wheel for external grinding, diameter-width-bore 400x50x127 mm Wheel for surface grinding 250x13x76 mm Grinding spindle speeds 1500/1700/2200/3600 rpm Grinding headstock swivel 270° With index every 90° Vertical movement of grinding headstock, centre height 125-350 mm Cross travel of grinding headstock 285 mm Hydraulic rapid advance/retract stroke 40 mm Intermittent feed of the wheel by table reversal 0.001-0.03 mm/dia Continuous plunge grinding feed 0-0.9 mm/dia Micrometric feed stop, graduated 0.001 mm/dia Workpiece headstock swivel 360° Nwodpsw U Ry Nofx Abzeh Continuously variable workpiece spindle speed, standard/special 20-400 / 10-400 rpm Workpiece headstock/tailstock internal taper 5/3 Morse Grinding headstock motor, approx. 4 HP All technical details are given without obligation and subject to errors or omissions.

Būklė: visiškai atnaujintas (naudotas), Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 32461/2384, Origin of manufacture: Switzerland Voltage: 380 / 50 / 3 (V/Hz/Ph) Net weight: 2200 kg TECHNICAL DATA Nominal distance between centres: 600 mm Maximum distance between centres (workpiece spindle stock and tailstock retracted): 750 mm Standard centre height: 125 mm Centre height with interchangeable intermediate plate (workpiece spindle and tailstock): 175 → 250 mm Maximum possible swing diameter (125 mm centre height): 250 mm Maximum possible swing diameter with intermediate plates: 350 → 500 mm Table swivelling range, each side: 10° Maximum grinding length (table width = 200 mm): 900 mm Table speed, hydraulically and steplessly adjustable: approx. 6 m/min Table reversal delay: 0–5 sec Grinding wheel for cylindrical grinding, diameter x width x bore: 350/400 x 50 max. x 127 mm Grinding wheel for surface grinding, diameter x width x bore: 250 x 13 x 76 mm Grinding spindle speeds (rpm): 1500 / 1700 / 2200 / 3600 Swiveling range of grinding spindle headstock: 270°, lockable every 90° Vertical travel of grinding spindle headstock (centre height): 125–350 mm Cross travel of grinding slide: 285 mm Hydraulic rapid advance and return of grinding slide: 40 mm Feed per table reversal, stepless: 0.001–0.03 mm/rev Feed amount for plunge grinding: 0–0.9 mm/rev Micro stop for feed per division: 0.001 mm/rev Swiveling range of workpiece spindle stock: 360° Workpiece spindle speeds, steplessly adjustable normal/special: 20–400 / 10–400 rpm Internal taper, workpiece spindle/tailstock: Morse 5/3 Grinding spindle motor, approx.: 4 HP Errors and omissions excepted. Technical data provided without obligation. Inventory No. 2170089, Machine Accessories List: Nwsdpfx Abod Amifozoh 1 workpiece spindle headstock MK5 1 sine bar without dial comparator 1 grinding spindle headstock with 4 drive pulleys 1 tailstock MK3 1 collet draw system with collet and reducing sleeve B32 1 internal grinding attachment with Fischer quill UJ50x250 – drive pulley Ø 48 for 14,000 rpm 1 rotatable disc dressing device with 50 mm base 1 table rotation stop without comparator 1 coolant system by decantation 1 ejector 1 balancing bar

Būklė: geras (naudotas), Distance between centers: 760 mm Max. Z-axis travel: 650 mm Maximum grinding length: 430 mm Maximum grinding diameter: 250 mm Center height: 125 mm Maximum grinding wheel diameter: 500 mm Nwodsv Tmtljpfx Abzeh Max. X-axis travel: 320 mm CNC brand: FANUC CNC model: 18TB Main motor power: 7.5 kW Z and X-axis resolution: 0.1 µm Workhead taper: MORSE 5 Workhead through bore diameter: 38 mm Tailstock taper: MORSE 4 Workhead spindle speed: from 8 to 800 rpm Dimensions (L x W): 2500 x 2000 mm Weight: 4700 kg

Būklė: labai geros būklės (naudotas), Gamybos metai: 2004, Funkcionalumas: visiškai funkcionalus, centro aukštis: 175 mm, ruošinio svoris (maks.): 180 kg, šlifavimo ilgis: 1 000 mm, šlifavimo disko skersmuo: 400 mm, bendras ilgis: 1 150 mm, šlifavimo skersmuo: 349 mm, The machine is operational and in use at our facility. It is equipped with 2 external diameter and 2 internal grinding spindles; features C-axis. Nwedpfsv Uxriox Abzeh

Būklė: naudotas, Atstumas tarp centrų: 1000 mm Centrų aukštis: 250 mm B ašis: Tikslumas 0.1° Nwjdpfjxmg Eksx Abzeh CNC gamintojas: Kelco CNC modelis: 90 Kairiojo šlifavimo rato matmenys (išor. x vid. x plotis): Ø400 x Ø127 x 63 mm Dešiniojo šlifavimo rato matmenys (išor. x vid. x plotis): Ø400 x Ø127 x 50 mm Ruošinio laikiklio galvos pasukimas: -30° +120° Ruošinio laikiklio galvos kūgis: MK 5 Didžiausias ruošinio svoris tarp centrų: 150 kg Atatrankos kūgis: MK 4 Atatrankos trumpinimo eiga: 50 mm Didžiausias perimetrinis greitis: 32 m/s Vidinio šlifavimo aukšto dažnio velenas: Ø120 mm Vidinio šlifavimo veleno gamintojas: WARNER, modelis K 3.000 Pagrindinio variklio galia: 7,5 kW Bendra galia: 26,5 kW Maks. Z ašies eiga: 1.150 mm Maks. Z ašies greitis: 15 m/min Darbo stalo pasukimas: 0°–9° Maks. X ašies eiga: 320 mm Maks. X ašies greitis: 7,5 m/min Ilgis: 3600 mm Plotis: 2000 mm Svoris (apytiksl.): 5.000 kg

Būklė: geras (naudotas), Atstumas tarp centrų: 1000 mm Centrų aukštis: 175 mm CNC prekės ženklas: FANUC Nwjdpfx Abetrgn Tezoh CNC modelis: Oi-TD