KRÜSI namelių statybos mašina TYPE CM 40

Krüsi CM40

Sąlyga: geras (naudotas), Gamybos metai: 1996, Funkcionalumas: visiškai funkcionalus, KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 Year of Manufacture: 1996 The Krüsi CM40 consists of the following components: - Circular saw (cross-cut saw) - Log house milling unit (horizontal and vertical) - Grooving mill (horizontal) - Boring unit - Infeed table 6 m - Outfeed table 6 m KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 Manufacturer: Krüsi Maschinenbau AG, CH-9105 Schönengrund AR Year of Manufacture: 1996 CE marked Condition: good, technically inspected and cleaned / ready for operation Operating Principle: Processing of timber for chalet or log house construction Beams can be processed in a single pass - Cross-cutting - Horizontal and vertical milling of necks / grooves in a single clamping - Drilling - Milling of end grooves Workpiece: - Max. cutting height: 200 mm - Max. cutting width: 250 mm Robust, welded construction. Machine (horizontal and vertical milling units) equipped with 4 special milling motors, hardened and ground guides for highest machining accuracy. Carriage guided by preloaded, dust-protected, ball-bearing rollers. Working range up to 200 x 250 mm. Fully operational, with contactor control, motors protected by thermal relays. Electrical equipment for 380 V, 50 Hz, with safety covers, central connection for customer-side chip extraction, 2 eccentric clamps, without milling tools (Falter). Featuring hydropneumatic horizontal and vertical feed, electrically controlled, operating in tandem with spindle motors. Rapid traverse and feed continuously adjustable. Completely wired and installed, including air maintenance unit. Beams thicker than 14 cm must be machined in two passes. Machine Description / Equipped with: 1. Saw Unit: Manual feed Spindle adjustment with analog position display Saw blade Ø max. / bore Ø: 400 / 30 mm Tungsten carbide tipped with chip depth limiter (synchronous operation) Adjustable riving knife Motor speed min 1 / 2900 Power kW 2.2 2. CM Milling Aggregate (Log House Milling Unit): Hydropneumatic feed Spindle adjustment with digital position display Horizontal milling unit Cutter Ø 180 mm Max. cutter width 130 mm For cutter width over 60 mm, use only aluminum alloy cutter with indexable inserts 2 motors, hydropneumatic feed, each 2.2 kW Hydropneumatic feed Rapid traverse and working feed continuously adjustable 3. Boring Unit: Manual feed Spindle adjustment with analog position display Drill holder - ER 25 collet Max. clamping Ø: 16 mm Max. drill Ø: 32 mm Motor min’1 1450, kW 1.8 Lhedsvfv Tfopfx Abroc 4. Planer Milling Unit: Hydropneumatic feed Spindle adjustment with digital position display Cutter Ø max. 230 mm Max. cutter width 60 mm Motor min1 / 2900, kW 3.0 2 V-belts SPZ 9.5x1000 La Pneumatics Operating pressure on site min/max MPa (bar) 0.7/1 (7/10) Air consumption Nm3/h 8 Electrical System Operating voltage V / Hz: 380, 50 Rated power kW: 8.8 - 15.8 depending on configuration Local fuse required: 3 x 25 A tr

Sąlyga: naudotas, Chipping rundvirke: 100–150 m³/t Flising av småved og avfall: 50–100 m³/t Vekt: 3165 kg Maks. stokkdiameter: 254 mm Söderhamn Eriksson 670-56 CC flishogger med elektrisk motor. Söderhamn Eriksson 670-56-flishoggeren er beregnet for produksjon av flis til tremasse, fiberplater og sponplater. Både rundvirke og sagbruksavfall kan benyttes som råstoff. Flishogger 670-56 mater horisontalt, i en vinkel på 37,5 grader mot fiberretningen. Flis av jevn og høy kvalitet kan enten ledes ut i bunnen eller blåses rett opp. Bli en av de sagbruksbedriftene som forvalter ressursene sine på en smart måte. Ljdpfshclffsx Abrohc

Sąlyga: geras (naudotas), Gamybos metai: 1994, I am selling an automatic CNC machining center for BLOCK-HOUSE production, Krüsi CM-40. Year of manufacture: 1994. - Crosscut saw - Tenoning unit (top and bottom) - Tenoning unit (left and right) - Dowel drilling unit - 4-head milling aggregation - Automatic feed system with ±1mm accuracy - Infeed length: 12m Ljdpfx Aber Atcyjrehc Ideal for timber construction! Available immediately.

Sąlyga: geras (naudotas), Gamybos metai: 1996, KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 Manufacturer: Krüsi Maschinenbau AG, CH-9105 Schönengrund AR Year of manufacture: 1996 Condition: Good, technically inspected and cleaned / ready for operation Operating principle Processing of timber for chalet construction / log house production. Beams can be processed in a single pass. • Cross-cutting • Horizontal and vertical milling of notches/grooves in a single clamping • Drilling • Milling of end grooves Workpiece: • Max. cutting height: 200 mm • Max. cutting width: 250 mm Rugged welded steel construction. Machine (horizontal and vertical milling units) equipped with 4 special milling motors, hardened and ground guides for maximum processing accuracy. Carriage guided by dust-protected, preloaded ball bearing guide rollers. Working range up to 200 x 250 mm. Fully operational, with contactor control system; motors protected by thermal relays. Electrical equipment for 380 V, 50 Hz, with protective covers, central connection for customer-provided chip extraction system; includes 2 eccentric clamps; no milling tools (rebate cutter). Features electro-hydropneumatic horizontal and vertical feed, synchronized with the start of the milling motors. Rapid traverse and feed rate steplessly adjustable. Fully wired and installed, including air service unit. Beams thicker than 14 cm must be processed in two passes; for these beams, the workpiece must be fed again to the extent of the excess thickness for further milling. Machine guards over all moving parts with gas spring counterbalance. Machine description / equipped with: 1. Saw unit: Manual feed Spindle adjustment with analog scale display Max. saw blade Ø / bore Ø: 400 / 30 mm Tungsten carbide tipped with chip depth limiter (uni-directional) Adjustable riving knife Motor speed min⁻¹: 2900 Power (kW): 2.2 2. CM milling unit (log house unit): Hydropneumatic feed Spindle adjustment with digital scale display Horizontal milling unit: Cutter Ø: 180 mm Max. cutter width: 130 mm For cutter width >60 mm only use aluminum alloy cutters with indexable inserts. 2 x hydropneumatic feed motors, each 2.2 kW Hydropneumatic feed; rapid traverse and working feed rate steplessly adjustable. 3. Drilling unit: Manual feed Spindle adjustment with analog scale display Drill chuck: ER 25 collet Max. clamp Ø: 16 mm Max. drill Ø: 32 mm Motor speed min⁻¹: 1450, Power (kW): 1.8 4. End milling unit: Hydropneumatic feed Spindle adjustment with digital scale display Max. cutter Ø: 230 mm Max. cutter width: 60 mm Motor min⁻¹/2900, 3.0 kW 2 V-belts SPZ 9.5x1000 La Pneumatics Required operating pressure min/max. MPa (bar): 0.7/1 (7/10) Air consumption: 8 Nm3/h Electrics Operating voltage V/Hz: 380 V, 50 Hz Rated power: 8.8 – 15.8 kW depending on configuration Customer-supplied fuse: 3 x 25 A (slow-blow) Max. simultaneous power demand: 4.4 kW Dimensions Machine width: 2400 mm Machine depth: 1600 mm Total height, guard lowered: 1600 mm Total height, guard raised: 2200 mm Extraction port Ø (under-floor extraction) Weight: approx. 1300 kg Including roller conveyor 2 x 6 m (2 x 4 m) Ljdpfeu Uh T Dsx Abrjhc Technical data subject to change!

Sąlyga: naujas, Gamybos metai: 2024, Magnetic separator for chip conveyor line Lhjdpfx Abscqvhwsrjc Tube magnet with 4 magnetic plates (permanent magnet) Hinged door for easy removal of metal parts Tube diameter: 180 mm Location: In stock at 54634 Bitburg - immediately available -

Sąlyga: naudotas, Gamybos metai: 1981, Atstumas tarp centrų: 1300 mm Kopijavimo ilgis: 1250 mm Centro aukštis nuo staklių pagrindo: 250 mm Centro aukštis virš atramos: 160 mm Pastumos greitis: 3 m/min Svoris: 630 kg Sukimosi greičiai: 500-1000-1500-3000-2100-4200 aps./min Hidraulinė Sandėliavimo vieta: Nattheimas Lhedpfx Abevvkt Iorec

Sąlyga: naudotas, Slot spindle 1 pc. Number of milling units: 4 pcs. Spindle diameter: 50 mm Control: Weinig, PC-Nexus # 2764 Weinig Unicontrol 6 with NC spindles ----- The machine will be cleaned and fully inspected before delivery. Technical Data Overview (additional accessories possibly included; please inquire separately) Pos. 1: Cross-cut saw ----- > Electronic cross-cut saw, horizontally adjustable steplessly > Number of tools: 1 pc. > Spindle speed: 2,800 rpm > Spindle diameter: 40 mm > Max. tool diameter: 400 mm > Motor power: 3.0 kW > Laser guide for saw cut detection > NC length stop, mounted on slot table included Positioning of cross-cut saw integrated in the control system. > Length: 3500 mm Pos. 2: Tenoning and slot spindle ----- > Number of tools: variable, stepless NC-axis adjustment > Tool clamping length: 320 mm > Vertical spindle stroke: variable, stepless 254 mm NC-axis adjustment > Spindle speed: 3,500 rpm > Spindle diameter: 50 mm > Max. tool diameter: 320 mm > Motor power: 11 kW Pos. 3: 1st Profiling spindle (climb & counter-rotation) > Position: vertical right > Number of tools: 1 pc. > Tool clamping length: 120 mm > Spindle speed: 6,000 rpm > Spindle diameter: 50 mm > Max. tool diameter: 232 mm > Motor power: 7.5 kW Pos. 4: 2nd Profiling spindle ----- > Position: vertical right > Number of tools: variable, stepless NC-axis adjustment > Tool clamping length: 320 mm > Vertical spindle stroke: variable, stepless 254 mm NC-axis adjustment > Spindle speed: 6,000 rpm > Spindle diameter: 50 mm > Max. tool diameter: 232 mm > Motor power: 11 kW 2 feed rollers opposite the spindle, axially pneumatically controlled, 2 positions Muntin guide consisting of: Guide rail on the stop (climb spindle section), muntin support bar from above in the area of the vertical right profiling unit and profiling spindle. Pos. 5: Horizontal profiling unit, top ----- > Clamping length: 40 mm > Spindle diameter: 40 mm > Motor power: 3.0 kW > Speed: 5,850 rpm > Max. tool diameter: 130 mm > Axial adjustment 30 mm, 8 positions via pneumatic turret > Radial adjustment 125 mm, 8 positions via pneumatic turret Pos. 6: 3rd profiling spindle (hardware spindle) ----- > Position: vertical right > Tool clamping length: 160 mm > Axial adjustment 115 mm, 8 positions via pneumatic turret > Radial adjustment 100 mm, 8 positions via pneumatic turret > Spindle speed: 5,850 rpm > Spindle diameter: 40 mm > Max. tool diameter: 210 mm > Motor power: 3.0 kW Additional Features ----- > Online-capable > Rebate device for tear-free rebating > Double-parts package > Return system for one-man operation: swivel belt > Screen control > Tilt window unit > Electronic angle display for tilt windows Lhjdsvu Hfqepfx Abrsc > Industrial PC, PC control/NEXUS > Weinig type production program > Without working tools No original pictures available yet. Images show an identical machine from our archive. ----- Price for the above-mentioned machine on request! ----- Option with surcharge: EUR 6,500.00 Note...

Sąlyga: naudotas, Gamybos metai: 1999, Payload: 19,990 kg Gross vehicle weight (GVW): 8,010 kg Front tire condition: 70% Rear tire condition: 70% Front tires: 245/70 R 17.5 Lhjdpfx Abjtr H Enerjc Rear tires: 245/70 R 17.5 For further information, please contact PFEIFER GROUP.

Sąlyga: paruoštas naudoti (naudotas), For turning plates, discs, or bowls up to 250 mm Ø. Lsdpfxjrh Hnts Abrohc Machine with vacuum clamping.

Gamybos metai: 1999, Sąlyga: labai geros būklės (naudotas), Manufacturer: VANGROENWEGHE Model/Type: M-300 Year of Manufacture: 1999 Machine Category: Through-Feed Sander Location: Gorzów Wlkp. Delivery Terms: Self-collection Delivery Costs: Borne by the Customer Commissioning Type: To be agreed Description: Notes: Manufacturer: VANGROENWEGHE Model/Type: TYPE F-300-COMBI/CE Year of Manufacture: 1998 Machine Category: Through-Feed Sander Location: Gorzów Wlkp. Delivery Terms: Delivery costs borne by the customer Commissioning Type: To be agreed Through-feed Sander VG TYPE F-300-COMBI-CE / 1998 High-performance Combi unit machine Contact roller and pad sanding Pneumatic oscillation and mechanical belt tensioning Motors: 7.5 + 1 HP / 380 V Abrasive belt dimensions: 300 x 1,900 mm Lhodpfx Asd Nmdkebroc