Diskinis metalo pjūklas

Kaltenbach KKS350

Sąlyga: naujas, Cutting capacity at 90 degrees: round 510 mm Cutting capacity at 90 degrees: square 480 mm Cutting capacity at 90 degrees: rectangle 610 x 450 mm Saw blade length: 5320 x 34 x 1.1 mm Blade speed: 15 - 100 m/min Table height: 820 mm Total power requirement: 3.0 kW Machine weight: approx. 2.3 t Space requirements: approx. 2.65 x 2.8 x 2.2 m For mitre cuts up to 45° to the left in fully automatic operation and up to 60° to the left in semi-automatic operation Kdjdpfx Aofu Nbbeh Eew Material height sensor (automatic cut-start detection) Automatic feed unit via ball screw with incremental feed and automatic length compensation Sensor on the saw blade for automatic adjustment of the saw stroke Fully automatic control of the saw frame and clamping device Hydraulic unit with automatic pressure shut-off in idle mode Mechanical chip removal brush Feed vice with double-sided opening Minimum offcut length: 100 mm Modern CNC control, freely programmable for multiple sawing jobs with various cutting lengths and quantities Automatic feed unit 500 mm via ball screw with incremental feed and automatic length compensation, adjustable for cut lengths from 25 to 9,999 mm Fully hydraulic control of saw frame and clamping units Pre-selection of 3 different material feed speeds Visualization of the entire workflow with easy data input

Sąlyga: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2015, Funkcionalumas: visiškai funkcionalus, X ašies eiga: 10 000 mm, Y ašies eiga: 3 000 mm, Z ašies eigos atstumas: 1 500 mm, greitas poslinkis X ašimi: 25 000 m/min, greitas poslinkis Y ašis: 25 000 m/min, greitasis eiga Z ašyje: 25 000 m/min, veleno greitis (maks.): 4 000 aps./min, RepairFIT+ by Dornhöfer The Difference. Including installation & commissioning! TECHNICAL MAIN DATA Year of manufacture: 2015 Capacities / Travel distances: Longitudinal (X): mm 10,000 Vertical (Y): mm 3,000 Kjdpfjv R Hwrox Ah Eedw Cross (Z): mm 1,500 Paintwork: graphite grey RAL 7024 / agate grey RAL 7038 Tool holder: ISO 50, DIN 69871 AD Pull stud: DIN 69872 Type A Taper: DIN 69871 Main drive: Motor / Make: Siemens main spindle drive Type 1PH7 Maximum drive power: from 198 rpm 100% duty cycle 41 kW Maximum torque: Constant up to 198 rpm 100% duty cycle 1,920 Nm Speed control / Gearbox: 3-stage (oil-cooled) with automatic changeover Spindle speeds 4,000 rpm: Low range rpm: 0 – 516 Medium range rpm: 460 – 1,288 High range rpm: 1,200 – 4,000 Axis drives / Feed rates: Axis drive motors: Rapid traverse max.: (X/Y/Z axis) 25,000 mm/min Feed rate max.: (X/Y/Z axis) 15,000 mm/min Feed force max.: (X axis) 35,000 N (Y/Z axis) 32,000 N Axis drive systems: X axis (longitudinal): Pinion / rack (Make: Atlanta) Y axis (vertical): Pre-tensioned ball screw Ø 63 x 20 Z axis (cross): Pre-tensioned ball screw Ø 50 x 20 Weight: (without clamping table / plate field) approx. 49,500 kg Power supply: approx. 60 kVA Innotrol HBG wireless handwheel Automatic tool changer with 60 magazine slots BIG Plus tool spindle Operator platform, height-adjustable by 1,800 mm and cross-travel by 800 mm Interface for adapter milling heads What does RepairFIT+ mean? With RepairFIT+ we offer you a profitable and safe entry to our product lines. Our machines undergo a strict selection process, are subject to a thorough deep-dive inspection and receive intensive cleaning from our experts. All identified defects, both technical and cosmetic, are professionally repaired to ensure the machine is delivered in excellent condition.

Sąlyga: naudotas, Gamybos metai: 2000, Grinding length 1600 mm Grinding width 600 mm Workpiece height 500 mm Total power requirement 50 kW Q U O T A T I O N We are pleased to offer you, subject to prior sale and errors, ex stock: B L O H M CNC-controlled precision surface grinding machine Model PLANOMAT 616 with SIEMENS 840 D control Year of manufacture 2000 Serial no. 14 67x _____ _____ Grinding area 1,600 x 600 mm (!) Table dimensions 2,000 x 600 mm Working height under grinding wheel approx. 150 – 500 mm Max. longitudinal table travel X 1,700 mm Max. vertical movement of upper carriage Y 550 mm Max. cross movement of upper carriage Z 560 mm Max. workpiece weight approx. 800 kg Table speed X-axis 30 – 30,000 mm/min Min. cross feed Z-axis 0 – 4,000 mm/stroke Vertical feed Y-axis 0.001 – 0.099 mm/stroke Y/Z axis feed rate 4 – 4,000 mm/min Grinding wheel Ø x width approx. 400 x 100 mm Infinitely variable grinding wheel speed via GS motor 300 – 1,250 rpm Ksdpfx Ahot Hxcbj Ejdw Spindle drive max. approx. 27.5 kW Total power requirement approx. 50 kW - 400 V – 50 Hz Total weight approx. 10,000 kg Accessories / special equipment: • SIEMENS CNC control 840 D with screen; SIEMENS components, WINDOWS interface Model MMC 103/PCU 50, operator guidance for direct entry of all grinding parameters, including roughing/finishing/spark-out cycles, slot grinding with (cross-) indexing device, automatic shut-off upon reaching grinding depth and return to home position, grinding wheel management, dressing programs/cycles, hand-held remote, etc. • All axes driven by ballscrews, DITTEL contact control • Infinitely variable grinding spindle speed via direct GS motor • Table-mounted diamond wheel dressing unit type PEA, electrically driven, with DITTEL gap control device, and separate straight dresser with diamond fleece and compensation; dressing cycles integrated in the control • Fitted magnetic chuck approx. 500 x 1,500 mm, make WAGNER, with demagnetising device • Attached electrical cabinet, separate flanges with wheels, separate oil mist extractor, complete work space enclosure with sliding door and glass insert • Large HOFMANN coolant system TECHNOPUR S 300 with cooling unit and grinding sludge conveyor, tank 1,600 l or 1,280 l, separate oil mist extraction, etc. Condition: Good to very good – soon ready for demonstration, extremely large and stable machine (!) Delivery: Ex stock – as inspected Payment: Strictly net – upon receipt of invoice We look forward to receiving your order. Further grinding machines of all types in stock. Please inquire.

Sąlyga: labai geros būklės (naudotas), Gamybos metai: 2018, veikimo valandos: 1 730 h, Funkcionalumas: visiškai funkcionalus, tekėjimo ilgis: 760 mm, sukimosi skersmuo virš skersinio stumduko: 780 mm, tekėjimo skersmuo: 376 mm, ašies variklio galia: 22 W, veleno greitis (min.): 20 aps./min, veleno greitis (maks.): 4 000 aps./min, veleno skylė: 82 mm, X ašies eiga: 260 mm, Y ašies eiga: 105 mm, Z ašies eigos atstumas: 830 mm, tvirtinimo skersmuo: 24 mm, greitas poslinkis X ašimi: 30 m/min, greitas poslinkis Y ašis: 10 m/min, greitasis eiga Z ašyje: 30 m/min, strypo praėjimas: 80 mm, tvirtinimo įvorės skylė: 80 mm, Strypo skersmuo (maks.): 80 mm, CNC Turning-Milling Center Doosan Puma 2600 SYII with Fanuc i Series Control including Accessories The machine has been used very little, with approximately 1,730 power-on hours, so it is as good as new and will be available from 01.01.2026. Additional accessories for the Doosan Puma 2600 SY II lathe: - 2 tool holders for external turning tools 25x25 - 1 double tool holder for external turning tools 25x25 - 1 tool holder for face machining 25x25 - 2 tool holders for internal turning tools (boring bars) diameter 50 mm - 1 double tool holder for internal turning tools diameter 32 mm - 1 parting tool holder Kedpfxsxauwbo Ah Eedw - 1 double right-hand tool holder for external tool (sub-spindle) - 1 double left-hand tool holder for external tool (main spindle) - 4 driven tool holders ER-32 radial (X axis) - 5 driven tool holders ER-32 axial (Z axis) - 1 driven tool holder ER-32 radial (X axis) with internal coolant supply - 1 driven tool holder ER-32 axial (Z axis) with internal coolant supply - 1 three-jaw chuck for main spindle with 1 set of hardened jaws + 2 sets of soft jaws - 1 three-jaw chuck for sub-spindle with 1 set of hardened jaws + 2 sets of soft jaws - 1 collet chuck for main spindle + one collet each diameter 50 mm + 30 mm - 1 collet chuck for sub-spindle + one collet each diameter 50 mm + 30 mm - 1 set of reduction sleeves for diameter 50 (10 pieces) - 1 set of reduction sleeves for diameter 32 (7 pieces) - 1 set of adapters for driven tool holders (ER 32 collet, Weldon, milling arbor) - Flushing device with emulsion on main spindle for automatic cleaning of chuck jaws - Device for automatic cleaning of chuck jaws with compressed air - Additional high-pressure pump for internal coolant supply (for drilling with indexable insert drill) - Function for automatic machine shutdown (the machine also switches off the main switch, thus disconnecting the power supply) - Connection for automatic bar feeder magazine Iemca

Sąlyga: geras (naudotas), Gamybos metai: 2006, veikimo valandos: 21 437 h, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 122574, Controller: OSP P200 L Sehr geringe Spindelstunden. Max. Drehdurchmesser: ø 720 mm Abstand zwischen den Spindeln: 2.000 mm Spindeldrehzahl: 3.500 U/min Spindelleistung: 30 kW Gegenspindel; Spindeldrehzahl: 3.800 U/min Spindelleistung: 22 kW Werkzeugantrieb Drehzahl: 5.000 U/min Werkzeugantriebsleistung: 22 kW Kjdpsurfz Ijfx Ah Esdw Anzahl der Werkzeuge unten Revolver: 12 Obere Frässpindel: HSK100 ATC: 32-fach HSK100 Y-Achse: 250 mm (+125 / -125) Aufstellfläche: 6.150 x 3.073 mm

Gamybos metai: 2024, Sąlyga: naujas, The robust manual length stop MD 100 m enables you to efficiently increase the productivity and quality of your production. The operator can quickly and accurately position the carriage at the desired location. The specially developed clamping system provides the carriage with a very high holding force. Length measurement is performed using an easy-to-read measuring tape with mm graduation. Existing machines/conveyor roller tables can be retrofitted at any time. Product details: • Suitable for positioning steel profiles and solid material • Carriage features triple ball-bearing guidance • Smooth operation allows for fast and precise length positioning • Manual stop clamping via large adjustable hand knob • Specially developed clamping system with very high holding power • Manual arm raising and lowering • Measuring rail with measuring tape and vernier (resolution 0.10 mm) • Standard measuring lengths: 1 m to 6 m, maximum up to 20 m • Total system length = measuring length + 0.3 m • Available in left or right-hand versions • Mounting screws included • Accessories: - Stop arm with spring damping - Manual arm return via hand lever - Arm return with shock absorber via pneumatic cylinder Kdjdpfx Ahsidlpis Eow - Various material roller conveyors available Plantec Maschinen GmbH

Sąlyga: naudotas, Gamybos metai: 2015, TAKISAWA TS4000YS metai 2015 CNC valdymas FANUC 32i-MODEL B Maksimalus tekinimo skersmuo 315 [mm] Maksimalus prasisukimas virš lovos 600 [mm] Maksimalus tekinimo ilgis 735 [mm] X ašies eiga 267 [mm] Z ašies eiga 840 [mm] Y ašies eiga -50 [mm] / +70 [mm] A ašies eiga 780 [mm] Kodpfxewq Sf Ts Ah Ejdw Spartusis įsibėgėjimas X ašis 30000 [mm/min] Spartusis įsibėgėjimas Z ašis 30000 [mm/min] Spartusis įsibėgėjimas Y ašis 10000 [mm/min] Spartusis įsibėgėjimas A ašis 30000 [mm/min] Pagrindinis špindelis A2-8" Maksimalus strypo skersmuo 82 [mm] Špindelio pervada 94 [mm] Maksimalus špindelio greitis 4200 [aps./min] Špindelio galia 22 [kW] Priešpriešinio špindelio nosele F140 Priešpriešinio špindelio pervada 53 [mm] Maksimalus priešpriešinio špindelio greitis 6000 [aps./min] Priešpriešinio špindelio galia 11 [kW] Maksimali įrankių laikiklio skerspjūvio dalis 25 [mm] Įrankių stočių kiekis 15 Varomų įrankių stočių kiekis 15 Maksimalus varomų įrankių greitis 6000 [aps./min] Tepimo bakelio talpa 370 [l] Bendras reikiamas galingumas 37 [kVA] Tiekimo įtampa 400 [V] Drožlių transporteris su staklėmis 5 varomi įrankių laikikliai Svoris 6700 [kg]

Sąlyga: naudotas, Gamybos metai: 2008, Technical details: X-axis travel: 6500 mm Y-axis travel: 1400 mm Z-axis travel: 1000 mm Table size: 7000 x 1100 mm Milling spindle speed range: 15 – 4000 rpm Spindle taper ISO: 50 Rapid traverse speed: 20 m/min Feed rate: 1 – 10,000 mm/min Total power requirement: 75 kW Machine weight approx.: 30 t Equipped with: Ksdpfxovmz I Ro Ah Eedw - CNC SIEMENS 840 D - Automatic indexing milling head, 0.001 x 0.001° increment - Automatic tool changer, 100 positions - Coolant system with internal coolant supply (IKZ) 30 bar - Chip conveyor

Sąlyga: geras (naudotas), Gamybos metai: 2008, šlifavimo ilgis: 1 250 mm, stalo ilgis: 1 250 mm, stalo apkrova: 1 200 kg, stalo plotis: 500 mm, veleno greitis (maks.): 2 600 aps./min, veleno greitis (min.): 1 000 aps./min, bendras svoris: 9 300 kg, X ašies eiga: 1 400 mm, Y ašies eiga: 600 mm, Z ašies eigos atstumas: 600 mm, galia: 185 kW (251,53 AG), įėjimo įtampa: 400 V, reikalingas aukštis: 2 870 mm, Įranga: sūkių greitis be galo kintamas, X-axis: Grinding length 1,250 mm, travel distance 1,400 mm Y-axis: Distance table to spindle center 700 mm, travel distance 600 mm Z-axis: Grinding width see note, travel distance 600 mm Note: The grinding area in the transverse direction (Z-axis) depends on the travel distance and the grinding wheel width. Kedpfx Aeu Hiq Rsh Eodw Example: Transverse travel = 600 mm Grinding wheel width 60 mm = grinding width 660 mm Grinding wheel width 100 mm = grinding width 700 mm See pictures for more technical data

Sąlyga: naudotas, Gamybos metai: 1979, Pjovimo skersmuo 440 mm Mašinos svoris apie 780 kg Ksdpfxsf Dwa Uj Ah Eedw +++++ Atkreipkite dėmesį, kad įrenginys yra išardytas ir paruoštas pakrovimui. Dėl šios priežasties negalima atlikti demonstracijos įjungus maitinimą ar pagaminti vaizdo įrašo. Mūsų skelbime pateiktos informatyviausios ir aukščiausios kokybės nuotraukos. Deja, papildomų nuotraukų atsiųsti negalime. +++++