Balu presas

HSM GmbH + Co. KG VK 8818 R-FU

Good day,

We hereby offer you, without obligation, a used, complete bale press line consisting of a baler from HSM, type VK 8818 R-FU including conveyor technology and wire feed stations.

The following technical data have been taken from the manufacturer's operating manual and brochures, for the accuracy and completeness of which we cannot accept any liability.

Technical data – press:
Manufacturer: HSM GmbH + Co. KG, Germany
Type: VK 8818 R-FU
Year of manufacture: 2015
Operating hours: 20,331 hours (as of September 2025)
Number of bales pressed: 29,020 bales (as of September 2025)
Pressing force, main press: 1000 kN
Specific pressing force: 120 N/cm²
Pressing force, shearing edge ejector: 121 kN
Feed opening dimensions: 970 x 1,800 mm
Theoretical cycle time (idle): 8.3 seconds
Theoretical throughput: 643 m³/hour
Bale dimensions: 1,100 x 750 mm; variable length, 600 up to 2000 mm
Drive power: 2 x 45 kW, frequency-controlled
Connected load: 110 kW
Total current consumption: 213 A
Fuse protection: 250 A slow-blow
Tying: 5-fold horizontal, fully automatic
Dsdpfx Asyz Af Esc Deur
Throughput rates at bulk density of:
20 kg/m³: 12.86 t/hour
50 kg/m³: 32.15 t/hour
Bale weights at a bale length of approx. 1.2 m: 650 – 750 kg/bale, depending on material
Hydraulic oil tank capacity: 2,000 L HVI 46
PLC control: Siemens S7-300
Operator panel: Siemens TP 700
Overall press dimensions assembled: 12,130 x 4,800 x 3,270 mm (L x W x H)
Installation dimensions (press with conveyor system): 35,000 x 8,480 x 7,745 mm (L x W x H)
Weight of the press: approx. 33 t (main press approx. 12 t, press channel with bale clamp approx. 10 t)

Special equipment ordered additionally:
Frequency-controlled main drive, 2 x 45 kW, with up to 40% energy savings compared to the standard drive (2 x 45 kW) with identical output performance
Manual switching on/off of the number of wire ties to save strapping wire on non-expansive materials
Shearing edge ejector with 121 kN pressing force
Sensor-based wire monitoring with press shutdown in the event of wire breakage or wire end
Bale chute
Visual warning signal, mounted on the control cabinet

Condition of the press:
The entire press line (baler and conveyor system) is in good, immediately operational condition. The system was cleaned weekly by the operator, lubricated and serviced as specified by the manufacturer.

Technical data – chain belt conveyor:
Manufacturer: Stadler Anlagenbau GmbH
Type: Chain Belt Conveyor KF 1800
Year of manufacture: 2015
Belt speed: 0.36 m/second
Feed belt length: 7,000 mm
Incline belt length: 14,500 mm
Gooseneck length: 1,550 mm
Incline: 30°
Nominal width: 1,800 mm
Usable width: 1,638 mm
Overall conveyor height: 7,745 mm
Pit dimensions for conveyor: 11,200 x 3,000 x 1,250 mm (L x W x H)

Scope of delivery:
HSM VK 8818 R-FU baler
Maintenance platform
Bale chute
Wire feed stations
Wire roll trolleys (without wire rolls)
Stadler chain belt conveyor KF 1800
Transverse sliding belt conveyor
Pit cover from feed conveyor to pit
Second control cabinet for press operation at the conveyor
Machine documentation in English

Delivery time:
The entire line is already dismantled, stored, and can be loaded at short notice after receipt of payment.

We would be pleased if this or one of our other baling presses is of interest to you.

Your Service Team
Mertens & Frowein GmbH

Skelbimas buvo automatiškai išverstas. Galimos vertimo klaidos.