Dvigubo galo tenoneris - viena mašina

HOMAG NFL 25/4/10

Sąlyga: naudotas, Gamybos metai: 2001, Wood dimensions to be processed: Incoming lengths min/max: 500 – 6500 mm; Full optimization up to max. 1500 mm. Incoming widths min/max: 40 – 300 mm. Incoming thicknesses min/max: 15 – 120 mm. Maximum wood cross-sections: 300 x 40 mm, max. 200 x 120 mm. Fixed lengths after saw: min. 510 – 2800 mm. Special application: Cutting of blocks, length min/max: 100 – 200 mm (Note: multiple block length during sorting, blocks are transported to the end of the sorting line and drop into customer-side mesh boxes). Cut/trimming tolerance: +/- 0.8 – 1.5 mm (for wood with minimum resin content and even surface. Tolerance up to 1 m fixed length, max. tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm. Curvature of wood in all directions: max. 10 mm per meter length. Types of wood: Softwood or hardwood. Machine performance: Feed speed continuously adjustable up to max. 230 m/min; cutting cycle 0.6 – 1 s. To determine the practical daily output, an effectiveness factor dependent on the customer’s production conditions must be considered. Infeed and saw working height: 900 mm (install required on customer-side platform, saw requires concrete base). Sorting working height: 2000 mm. Connection values: Total electrical connection load approx. 18 kW. Operating voltage: 380 Volt / 50 Hz. Voltage fluctuations max. 5 %. Air consumption approx. 1200 NL/min. Operating pressure approx. 8 bar. Extraction velocity approx. 30 m/s. Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B. Bcsdpfsw Sy T Hsx Agijw POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge. Pos. 2: Support roller without drive, at the end before steel table for easier feeding. Pos. 3: Length measuring station with built-in fluorescence camera for detecting defect markings. Pos. 4: Automatic non-contact width measurement. Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with built-in waste chute incl. equipment package for large wood cross-sections. Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and plant control. The following are available for processing: - max. 16 product groups - max. 8 qualities per product group - max. 200 fixed lengths per product group. Pos. 6: Discharge conveyor belt as sorting station with drive unit, length 7500 mm. Pos. 7: 2 ejectors mounted on discharge conveyor belt. Location: Nattheim

Sąlyga: labai geros būklės (naudotas), Independent machine - Universal machine (First & Second in a machine line) Electronic control – EasyLing programmer Safe and soundproof casing No. 3+3 vertical columns to support the working units Min. useful working width (mm): 240 Max. useful working width (mm): 3,100 Min. useful working thickness (mm): 3 Max. useful working thickness (mm): 150 Retractable positioning cams, spacing (mm): 800 Feed rate (min/max), stepless adjustment (m/min): 4 – 24 Total power No. 4 machining groups (for each side of the machine): Bedpfxewhmdfe Agijcw Scoring unit Automatic scoring unit 1 x 3 kW (6,000 RPM) Planing unit 1 x 6 kW (6,000 RPM) 0–10° Universal milling unit (electropneumatically controlled) 1 x 6 kW (6,000 RPM) 0°–90° Universal milling unit 1 x 6 kW (6,000 RPM) 0°–90°

Sąlyga: naujas, Gamybos metai: 2022, Funkcionalumas: visiškai funkcionalus, Naujas Friulmac EQ 004 2.5 su padavimo konvejeriu ir padavimo bunkeriu Valdymas liečiamu ekranu ir automatinis reguliavimas Bcsdpfx Agjvupm Djiew Darbinis ilgis: min 190 mm – maks 2500 mm Plotis: min 30 mm – maks 250 mm Storis: min 12 mm – maks 35 mm Greitis: 6–25 m/min 2 x 2 Viršutinis velenas – 3 kW – 720 aps./min. Pagrindinis profiliavimo velenas – 4 kW – 7200 aps./min. Dėl išsamesnės informacijos galiu atsiųsti originalią dokumentaciją.

Sąlyga: labai geros būklės (naudotas), Line for door frames (casings), for cutting, milling of strike plates, and inserting hinges (ANUBA) comprising: X10030A) Discharge conveyor X10030B) Transfer unit X10030C) Double cutting and drilling machine "AMS" - 45° left-side cut – Drilling - 90° cut - 45° right-side cut – Drilling Bcodsqwycljpfx Agiew X10030D) Angle conveyor (90°) X10030E) Anuba hinge insertion machine "MASTERWOOD" model MULTITEC X10030F) Strike plate milling machine "MASTERWOOD" model Teknomat 3000

Sąlyga: naudotas, mašinos/transporto priemonės numeris: 4/14242, Frank floor sanding machine FSR, used Bodpfx Agjb Auu Rsijcw Motor power: 0.75 kW Voltage: 230 Volts 5 Amps, 50 Hz, Machine no.: 4/14242 Dust bag Location: Ex stock Bitburg

Sąlyga: naudotas, Gamybos metai: 2021, Funkcionalumas: visiškai funkcionalus, The BP 800 is an automatic bundle shrink wrapper. Products with a width of up to 760 mm and a height of up to 380 mm can be packaged. Semi-automatic bundle packer Pneumatic pusher Swiveling PLC display Adjustable air flow in the shrink tunnel Transport rods made of heat-resistant fiberglass LD-PE film 25 – 80µm Low energy consumption Bodpfxjwth Dqj Agiscw CE-compliant Technical data Power supply: 380 V Output per minute: 10 bundles Sealing bar usable width: 760 mm Maximum product height: 380 mm Maximum film roll width: 750 mm flat film Compressed air: 6 bar Working height: 945 - 1105 mm Machine dimensions (LxWxH): 2665 x 1410 x 2105 mm Weight: 605 kg Download data sheet

Sąlyga: labai geros būklės (naudotas), 3-axis (X-Y-Z) CNC machining center – Cantilever design Movable horizontal plate (workpiece), static machining head Control system (BiesseWorks software), with separate electrical and control panels Machining head safety enclosure, safety tread mats Infeed table (workpiece support) at entry No. 2 workpiece clamping vices positioned within the working area Outfeed table (with conveyor belt) Minimum workpiece dimensions (X-Y-Z) mm 90 x 70 x 8 (approx.) Maximum workpiece dimensions (X-Y-Z) mm 3000 x 1300 x 60 (approx.) Total connected load (kW) 24 WORKING UNITS (TOP): Independent vertical drilling spindles: 29 pcs. Independent horizontal drilling spindles: 10 pcs. (8 X + 2 Y) Grooving saw unit (for X-axis machining), diameter 160 mm (1 pc. x approx. 3.5 kW) Vertical main spindle (milling unit) ISO 30 (1 pc. x approx. 4.5 kW) WORKING UNITS (BOTTOM): Independent vertical drilling spindles: 29 pcs. Bcedpfxewb Allo Agiew Independent horizontal drilling spindles: 10 pcs. (8 X + 2 Y) Grooving saw unit (for X-axis machining), diameter 160 mm (1 pc. x approx. 3.5 kW) Vertical main spindle (milling unit) ISO 30 (1 pc. x approx. 4.5 kW)

Sąlyga: naudotas, Gamybos metai: 2017, Funkcionalumas: visiškai funkcionalus, bendras plotis: 400 mm, galia: 26 kW (35,35 AG), TECHNINIAI DUOMENYS Didžiausias darbo plotis: 400 mm Darbo aukštis: 2 - 150 mm Minimalus ruošinio ilgis: 150 mm Darbo stalo aukštis: 900 mm Elektros varikliai: Plonų lakštų obliavimo variklio galia: 22,0 kW Pavaros variklis: 3,0 kW Kėlimo variklis: 0,50 kW Įrankis: Rotoriaus sūkių skaičius: Su reguliuojamu pavaros greičiu: 2.100–3.000 aps./min Bodpfsw Thpfox Agiocw Peilių skaičius: 48 vnt.

Sąlyga: geras (naudotas), Funkcionalumas: visiškai funkcionalus, number of engines: 4+4 opening: 6 metres Bcedsw D Nq Tjpfx Agiow

Sąlyga: labai geros būklės (naudotas), Rąstų žievinimo įrenginys VK450 2RE. Įrengtas dviem rotoriais. Vienas yra kelmo frezos rotorius. Kitas – žievės šalinimo rotorius. Min-max rąsto diametras 8–45 cm. Minimali rąsto ilgis 3 m. Komplekte su originaliu VK centrinančiu konvejeriu. Bus parduodamas po kapitalinio remonto. Bcsdpfxjulv Hzo Agijw