Stumdomas stalo pjūklas

SCM SIGMA 115 PLUS

Gamybos metai: 2011, Sąlyga: labai geros būklės (naudotas), This is a complete plant for house construction. Prices for each item are listed individually. Comprising the following elements (see attached document): Images will follow and are already included in the attached document. Table 1 (Positioning and clamping the stud frame) €34,500 • Adjustable longitudinal conveyor with 3 hinged belt conveyors and sheathing • Pneumatic cross-clamping • Connections for compressed air and electricity Table 2 (Placing and fastening the first sheathing layer) €25,300 • Longitudinal conveyor with 3 hinged belt conveyors and sheathing • Pneumatic cross-clamping • Connections for compressed air and electricity Intermediate conveyor, 3 m length (parking bay for multifunction bridge) €4,600 • Longitudinal conveyor with 3 hinged belt conveyors Table 3 (Placing the second sheathing layer, fastening, and flipping the element onto the next table) €35,650 • Longitudinal conveyor with 3 hinged belt conveyors and sheathing • Pneumatic cross-clamping • Connections for compressed air and electricity • Hydraulic turning device Table 4 (Installation of electrical systems and insulation) €34,500 • Cross transfer with rollers and sheathing • Table cross-travel function • Connections for compressed air and electricity • Hydraulic turning device Table 5 (Placing the first sheathing layer and fastening the second side) €32,775 • Longitudinal conveyor with 3 hinged belt conveyors • Cross transfer with rollers • Pneumatic cross-clamping • Connections for compressed air and electricity Intermediate conveyor, 3 m length (parking bay for multifunction bridge) €4,600 • Longitudinal conveyor with 3 hinged belt conveyors Table 6 (Placing and fastening the second sheathing layer) €28,750 • Longitudinal conveyor with 3 hinged belt conveyors • Pneumatic cross-clamping • Connections for compressed air and electricity Table 7 (Erection and distribution table) €29,900 • Longitudinal conveyor with 3 hinged belt conveyors • Hydraulic tilting unit • Table cross-travel unit • Overhead guide for holding the walls vertically Manual surface gantry with vacuum lifter on Table 2 (placing the first sheathing layer) €13,800 • Load capacity 85 kg with Schmalz vacuum unit • Steel base frame with low-friction rails • Travel range 12 x 5 m Lsdpou D Amgsfx Af Ijhb Manual surface gantry with vacuum lifter on Table 3 (placing the second sheathing layer) €13,800 • Load capacity 85 kg with Schmalz vacuum unit • Steel base frame with low-friction rails • Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 5 (placing the first sheathing layer on the second side) €13,800 • Load capacity 85 kg with Schmalz vacuum unit • Steel base frame with low-friction rails • Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 6 (placing the second sheathing layer on the second side) €13,800 • Load capacity 85 kg with Schmalz vacuum unit • Steel base frame with low-friction rails • Travel range 12 x 5 m Wall storage 1: 12 m long, 24 bays €11,500 Wall storage 2: 12 m long, 20 bays Vacuum lifter with column-mounted slewing crane €9,200 1 traverse, 2 t Abus €20,125 1 traverse, 2 t

Sąlyga: labai geros būklės (naudotas), Gamybos metai: 1995, Max. panel width: 4400 mm Max. panel length: 4300 mm Lhjdpfx Aomt Hhwof Iob Max. main saw blade projection: 110 mm Number of clamping units: 8

Sąlyga: labai geros būklės (naudotas), Rąstų žievinimo įrenginys VK450 2RE. Įrengtas dviem rotoriais. Vienas yra kelmo frezos rotorius. Kitas – žievės šalinimo rotorius. Min-max rąsto diametras 8–45 cm. Minimali rąsto ilgis 3 m. Komplekte su originaliu VK centrinančiu konvejeriu. Bus parduodamas po kapitalinio remonto. Lhedsulv Hzopfx Af Ieb

Gamybos metai: 2000, Sąlyga: geras (naudotas), EWD Combimes apkantavimo linija. Pagaminimo metai 2000, tipas DK90-TL. Medžio padavimas iš kairės. Didžiausias apkantavimo plotis 500 mm, didžiausias storis 120 mm. 90 kW variklis. Takto dažnis su 4,0 m ilgio medžiu apie 18 vnt./min. Komplektuota su originalia EWD valdymo sistema. Pristatymas nuo kaupiklio konvejerio prieš atskyrimą iki skutelių separatoriaus įskaičiuotas. Įrenginys pilnas, geros būklės. Ledpfexcwvxox Af Iehb

Sąlyga: naudotas, Gamybos metai: 2001, Wood dimensions to be processed: Incoming lengths min/max: 500 – 6500 mm; Full optimization up to max. 1500 mm. Incoming widths min/max: 40 – 300 mm. Incoming thicknesses min/max: 15 – 120 mm. Maximum wood cross-sections: 300 x 40 mm, max. 200 x 120 mm. Fixed lengths after saw: min. 510 – 2800 mm. Special application: Cutting of blocks, length min/max: 100 – 200 mm (Note: multiple block length during sorting, blocks are transported to the end of the sorting line and drop into customer-side mesh boxes). Cut/trimming tolerance: +/- 0.8 – 1.5 mm (for wood with minimum resin content and even surface. Tolerance up to 1 m fixed length, max. tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm. Curvature of wood in all directions: max. 10 mm per meter length. Types of wood: Softwood or hardwood. Machine performance: Feed speed continuously adjustable up to max. 230 m/min; cutting cycle 0.6 – 1 s. To determine the practical daily output, an effectiveness factor dependent on the customer’s production conditions must be considered. Infeed and saw working height: 900 mm (install required on customer-side platform, saw requires concrete base). Sorting working height: 2000 mm. Connection values: Total electrical connection load approx. 18 kW. Operating voltage: 380 Volt / 50 Hz. Voltage fluctuations max. 5 %. Air consumption approx. 1200 NL/min. Operating pressure approx. 8 bar. Extraction velocity approx. 30 m/s. Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B. POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge. Pos. 2: Support roller without drive, at the end before steel table for easier feeding. Pos. 3: Length measuring station with built-in fluorescence camera for detecting defect markings. Pos. 4: Automatic non-contact width measurement. Ledjw Sy T Hopfx Af Iehb Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with built-in waste chute incl. equipment package for large wood cross-sections. Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and plant control. The following are available for processing: - max. 16 product groups - max. 8 qualities per product group - max. 200 fixed lengths per product group. Pos. 6: Discharge conveyor belt as sorting station with drive unit, length 7500 mm. Pos. 7: 2 ejectors mounted on discharge conveyor belt. Location: Nattheim

Sąlyga: naudotas, mašinos/transporto priemonės numeris: 007186, Type of attached edge: thin edge, thick edge Gluing system: EVA Joint trimming: yes Multifunction unit: yes Top trimming unit: yes Max. feed speed: 18 m/min Lhjdsu T Tuwepfx Af Ijb Maximum panel thickness: 60 mm Working units: 10 pcs

Sąlyga: reikia remonto (naudotas), Machine for turning small wooden pieces. The machine processes thicknesses from 7 to 45 mm. Ljdpjuknznefx Af Iehb

Sąlyga: labai geros būklės (naudotas), PANEL SAW ANGLE SYSTEM Control: OSI Plus - Optiplanning Software No. 2 powered roller conveyors, each approx. 4500 x 2200 mm Lift table (mm): 4500 x 2200 1st pusher saw with 5 grippers Rotating device (for panels) up to 90° 1st panel saw max. cutting width (mm): 4500 Max. saw blade projection (mm): 152 Scoring saw (max. saw diameter): approx. 215 mm Main saw (max. saw diameter / power): 530 mm (30 kW) Variable saw carriage feed (m/min): 1 - 170 Shear for waste material reduction 2nd pusher saw with 10 grippers 2nd panel saw max. cutting width (mm): 2200 Max. saw blade projection (mm): 152 Scoring saw (max. saw diameter): approx. 215 mm Lsdpfxeukhd Ae Af Ijhb Main saw (max. saw diameter / power): 530 mm (30 kW) Variable saw carriage feed (m/min): 1 - 170 No. 2 front air cushion tables (mm 2200 x 1500) Automatic unloader (bridge) for cut panels: "RBO (BIESSE)" model Lifter with no. 6 stacking positions

Sąlyga: naudotas, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 200 t, stalo plotis: 300 mm, pjovimo aukštis su įrėžėju (maks.): 100 mm, frezos veleno ilgis: 250 mm, Equipment: - 1 GRECON feeding transfer system with accumulation for 4 to 5 purged boards of varying lengths for finger-jointing Ljdpswz H Ansfx Af Ijhb - 1 GRECON double finger-jointer for deep joints (for glulam beam production) - 1 180° transfer with two-component glue application - 1 GRECON finger-jointing press - 1 cross-cut saw with CNC control - 1 outfeed table

Sąlyga: beveik kaip naujas (parodų įrenginys), Demonstration unit with 7 operating hours Another machine available immediately (ex works Neckartailfingen) Shredder MRZ 830 Customs tariff number: 84659600 Feed opening: 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 phase Knives: reversible several times Hydraulically operated pusher Screen perforation of your choice (10 - 40 mm) Weight approx. 1,600 kg Dimensions (LxWxH) approx. 2290 x 1420 x 1750 mm Turbo clutch Standard features include: - Automatic star/delta start - High-speed hydraulics - Automatic shut-off when rotor is idling - Speed: 70-90 rpm for high throughput - Intermittent control to prevent idle times - Performance-boosting step control for hydraulic pusher - Pertinax guides for hydraulic pusher - Vibration-damping machine feet - CE compliant The shredder is designed for shredding untreated wood, chipboard and MDF panels, and other materials subject to testing and approval by the manufacturer. Includes: - Shredder elevated by 30 cm (prepared for conveyor belt installation) Additional shredder options: - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Discharge height: approx. 2000 mm (+/- 100 mm) - Overband magnet + €6,780 net - Control system for conveyor belt and overband magnet + €2,750 net (Start and stop each synchronized with the shredder) Raw material requirements: - The moisture content (oven-dried basis) must be below 30%. Lhjdjv Sqrpepfx Af Iob - Metals and mineral impurities such as sand, stones, etc. will increase wear.