Vertikali gręžimo mašina / vertikali BAZ

Robland BM 3000

Būklė: naujas, Gamybos metai: 2024, Axle: 920 mm X-axis: 3000 mm Material thickness Z: 12 mm - 30 mm Feed rate: 20 m/min A-axis: 360 degrees Minimum dimensions: Plate: x = 300 mm y = 120 mm z = 12 mm The machine is equipped with a 4-position drill chuck and a saw blade. Maximum and minimum hole diameters that can be drilled: 3 - 35 mm Kdjdpfscnz H Hsx Aiwot The saw blade operates in the X-direction. Maximum cutting depth with saw blade: 10 mm Motor: 0.75 HP, 400 Volt Required extraction capacity: 2300 m³/h Location: Ex stock 54634 Bitburg - Immediately available -

Būklė: naudotas, Gamybos metai: 2016, Panel saw with automatic pre-tensioning and double pusher system for optimized cutting Osi Plus numerical control unit Os Labeling labeling unit with onboard graphic marking, including part drawings Label printing management software Ksdpfouc Idxox Aiwsdt Optiplanning cut optimizer Cutting length: 4500 mm Cutting width: 2200 mm Blade projection: 95 mm Motorized rollers for side loading on lift table 4500 x 2200 mm. Translation speed: 10.8 m/min (50 Hz) – 13.1 m/min (60 Hz) Automatic identification of disposable sacrificial panels based on thickness data stored in the machine Low stack stop Automatic side loading. Includes: stop grids, double photocell, control keypad, electrical pre-installation for two motorized infeed roller conveyors, and reinforcement with 4 rollers instead of fork slots in the infeed conveyor Intermediate roller conveyor Side infeed roller conveyor, dimensions 3800 x 2200 mm with motorized rollers (floor height 325 mm) Dead roller conveyor for longitudinal offcuts for corner systems, 4500 mm (total length 7295 mm) 3000 mm extension for dead roller conveyor to also handle cross-cut offcuts Long chute for manual transport of cross-cut pieces to the central dead roller conveyor Air flotation unloading table, 2050 x 850 mm, equipped with wheels on the front Air blower unit for up to 6 air flotation layers MULTIPUSHER 2.4 system with automatic lubrication Additional mobile lateral aligner on the crosswise axis; this device enables reduction of the minimum panel length for cross-cutting from 1830 mm to 1220 mm Automatic device for detecting saw shaft deflection on angled cuts (longitudinal and transverse), consisting of a sensor capturing deflection directly at the saw arbor and a device counting blade revolutions directly at the saw chuck Keypad for remote cycle start Automatic panel loading via rear lift table Automatic double aligner with pneumatic cylinders Additional mobile lateral aligner on the crosswise axis Main saw blade, max. diameter (mm), 15 kW Scoring blade, max. diameter (mm), 2.2 kW Saw carriage speed 1–140 m/min with brushless motors Longitudinal pusher carriage speed 90 m/min Transversal pusher carriage speed 135 m/min Double pusher carriage: 6 clamps on the longitudinal slide + 10 clamps on the cross slide (8 fixed + 2 on the cross slide, Multi-Pusher system) Cutting system for thin panels

Būklė: naujas, Gamybos metai: 2026, Robland products are manufactured by Landuyt N.V., headquartered in Brugge, Belgium. BM-3000: • Grooving saw unit (maximum groove depth 10 mm) • Left drill bit 5 mm for producing line boring holes • 20 mm drill bit for creating Minifix systems • 8 mm milling tool for limited drilling and milling applications • 35 mm drill bit for hinges • Panel thickness that can be processed: 12-40 mm • The machine is equipped with a 4-position drill chuck and a saw blade • Y-axis range: Drilling: 900 mm / Sawing: 850 mm Technical Data: • Y-axis range: - Drilling: 920 mm - Sawing: 860 mm • X-axis support: 3000 mm Kodpfxjd Hz Nie Aiwedt • Z-axis, panel thickness from 12 mm to 40 mm • A-axis: 360° • Feed speed: 20 m/min • Minimum panel dimensions (X): 300 x (Y): 120 x (Z): 12 mm • The machine is equipped with a 4-position drill chuck and a saw blade • Maximum and minimum drill hole diameters: 3 mm – 35 mm • The saw moves along the X-axis • Maximum groove depth with saw blade: 10 mm • Motor: 0.75 HP, 3x 400V / 3x 230V • Minimum required extraction capacity: 2300 m³/h

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 2014, Funkcionalumas: visiškai funkcionalus, X ašies eiga: 3 000 mm, ruošinio aukštis (maks.): 30 mm, TECHNINĖS CHARAKTERISTIKOS Ašis: 920 mm X ašis: 3000 mm A ašis: 360° Medžiagos storis (Z ašis): 12 mm – 30 mm Pašaravimo greitis: 20 m/min Kjdpfx Ajzkt A Rjiwjdt Mažiausi matmenys (plokštė): X: 300 mm Y: 120 mm Z: 12 mm Maksimalus/minimalus skylės skersmuo: 3 mm – 35 mm Maksimalus pjovimo gylis su diskinio pjūklo ašmeniu: 10 mm STAKLĖS CHARAKTERISTIKOS Variklio galia: 0,75 AG Įtampa: 400 V Reikalinga ištraukimo galia: 2300 m³/h ĮRANGA 4 padėčių gręžtuvo tvirtiklis Diskinio pjūklo ašmenys, judantys X ašies kryptimi

Būklė: naudotas, Gamybos metai: 2018, Startech CN MAIN FEATURES FLEXIBLE AND INDIVIDUALLY CONFIGURED PRODUCTION COMBINED WITH SPEED AND PRECISION DRILLING FROM ABOVE WITH REFERENCE TO THE TOP SIDE OF THE PANEL ALLOWS FOR ABSOLUTE PRECISE PROCESSING NUMERICAL CONTROL WITH 7" COLOUR SCREEN: SIMPLE AND INTUITIVE TECHNICAL DATA Startech CN AXES Max. workpiece dimensions X-Y-Z mm 3050 x 800 x 50 Min. workpiece dimensions X-Y-Z mm 300 x 90 x 10 Working area drilling/grooving mm 0 x 800 / 0 x 800 Stroke of X-axis mm 750 Max. traversing speed X-Y axes m/min 25 DRILLING UNIT Vertical spindles number 7 (4X-4Y, one shared) Horizontal spindles (along Y-axis) number 2 (1+1) Horizontal spindles (along X-axis) number 1 Fixed groove saw (direction) X Diameter of groove saw mm 100 Max. thickness of groove saw mm 5 Motor power kW (HP) 1.5 (2) Spindle speed rpm 3350 Groove saw speed rpm 4300 INSTALLATION Power supply V (Hz) 380 / 400 (50 / 60) Installed power KVA 4.5 Compressed air requirement bar 6 Compressed air consumption Nl/cycle 90 Extraction requirement m³/h 1200 Extraction air speed m/sec 20 Extraction connection diameter mm 120 GENERAL FEATURES Universal CNC drilling machine with a working table with fixed gantry and moving workpiece for performing the following operations: - Vertical drilling on the panel surface - Horizontal drilling on all four workpiece sides - Grooving with an integrated groove saw in the 'X' direction Self-supporting structure Machine base made of steel tubular construction to provide a large base for accommodating the working table. The structure rests on 3 self-levelling feet. The electrical control cabinet is integrated into the machine base. Central Bakelite support table 'Easy Motion': - an MDF sector for through drilling, automatically retractable for horizontal drilling - an infeed roller to facilitate panel loading - a rear roller track to ease panel sliding - left and right stops - a central alignment device with manual adjustment The left and right stops must be used to drill horizontally in the 'X' direction on the two opposite panel sides. Panel positioning along the X-axis is via vacuum suction cups. Aggregates carrier This is a gantry structure made from steel tube. The main working unit is installed on the gantry. F10L drilling unit includes: - 7 independent vertical spindles - drill shank D10 mm - spindle pitch 32 mm - 2 horizontal drilling heads, 1 in X direction with one drill bit, 1 double drilling head in Y direction (1 + 1, drill shank D10 mm) - Speed 3350 rpm - 1 integrated sawing unit in X (max. diameter 100 mm) - Saw blade speed 4300 rpm - Motor power 1.5 kW - pneumatic vertical travel per spindle 70 mm - pneumatic horizontal travel of the drilling unit Workpiece positioning and drive of the working unit A CNC-controlled vacuum cup clamps and positions the workpiece sequentially under the working unit during processing. Movement along the X and Y axes is on THK guides with motion transmission via reinforced toothed racks. Z-axis movement is pneumatic on ball-bushing guides with stop position adjustable via the unit's positioning. Working unit positioning uses advanced drive and technology. -CONTROL The control software is specifically designed for use Kdodpfx Aovwbp Ajiwot

Būklė: naujas, Gamybos metai: 2026, Y-axis drilling: 920 mm Y-axis sawing: 860 mm X-axis: 3000 mm Z-axis: 12 mm - 40 mm A-axis: 360° Min. panel dimensions: (X) 300 mm x (Y) 120 mm x (Z) 12 mm Feed rate: 20 m/min Kedol D Rw Espfx Aiwodt Drill sizes: 5 mm / 20 mm / 35 mm Milling tool: 8 mm Grooving saw: 90 mm x 3.5 mm Maximum groove depth with saw blade: 10 mm Minimum hole diameter: 3 mm Maximum hole diameter: 35 mm Motor power: 1.3 kW Weight: 500 kg

Būklė: beveik kaip naujas (naudotas), Funkcionalumas: visiškai funkcionalus, Maszyna do osadzania kołków z pistoletem operacyjnym do jednoczesnego nakładania kleju i wprowadzania kołków. Standardowe kołki Ø8 mm Długość kołków: 25–80 mm Nominalna wydajność: 1 kołek/sekundę (wraz z aplikacją kleju) Stosuje kleje PVA na bazie dyspersji wodnej o lepkości 200–400 mPa 1 szt. zbiornik na klej o pojemności 8 kg 1 szt. zbiornik na wodę o pojemności 8 kg Maksymalne ciśnienie: 5 bar Kdedpfsqu N U Dsx Aiwst

Būklė: naudotas, Panel saw and shaper Robland NLX1700, very good condition, 2x 3 kW motors, approx. 2000 mm cutting length, approx. 100 mm cutting height, 1700 mm sliding table length, approx. 450 kg Price subject to change. Errors and omissions excepted. Ksdpfx Aiewzzh Eewsdt

Būklė: labai geros būklės (naudotas), Portal machine Movable panel, movable working head (horizontal workpiece) Numerical control Power Control, WoodWOP software Working head safety cabin. Complete machine safety enclosure Infeed support table (workpiece support). Outfeed table (with conveyor belts) Workpiece feed with no. 3 conveyor belts (feed speed (m/min) max approx. 130) Minimum workpiece dimensions (X-Y-Z) mm 250 x 100 x 15 Maximum workpiece dimensions (X-Y-Z) mm 2500 x 1050 x 60 Motorized conveyor belt for waste disposal Separate electrical and control cabinets. Total installed power (kW) 99 No. 2 WORKING UNITS (TOP): (SERVO-MOTOR X-Y-Z): No. 4 drilling units (4 x 2.3 kW) with 10 vertical spindles each (total vertical spindles 40) No. 3 WORKING UNITS (BOTTOM): (SERVO-MOTOR X-Y-Z): No. 6 drilling units (6 x 2.3 kW) with 40 vertical spindles each (total vertical spindles 240) Kdjdjgwbbqjpfx Aiwst No. 2 WORKING UNITS (HORIZONTAL): No. 2 drilling units with horizontal spindles No. 21 horizontal drilling spindles (right side) + no. 21 horizontal drilling spindles (left side) No. 8 injection nozzles for glue application and dowel insertion (right side) No. 8 injection nozzles for glue application and dowel insertion (left side) No. 2 dowel magazines for automatic dowel insertion OPTIONAL: BARCODE (WIRELESS SCANNER)

Būklė: labai geros būklės (naudotas), CNC MACHINING CENTER (POINT-TO-POINT) – 4 Axes Gantry-type design Power Control – woodWOP software Safety enclosure for the operating head Clamping table with 6 consoles Safety tread mats LASER system on X-axis for console positioning and on Y-axis for vacuum clamp positioning Automatic tool change system 2 disc-type tool changers – magazine/tool positions: 8 rear + 8 lateral Maximum working area (X – Y – Z) mm: 3130 x 1250 (1550) x 100 (150) Kdjdsyxn Tijpfx Aiwst 2 working areas – 1 x vacuum pump (capacity 70 m3/h) Chip conveyor Separate electrical control cabinet Total connected load: 32 A WORKING UNITS (TOP): 12 independent vertical drilling spindles (High Speed 7500) 6 independent horizontal drilling spindles (4 on X-axis + 2 on Y-axis) Drilling head motor power (kW): 2.3 1 grooving saw unit, diameter 125 mm, N1 – swivels 90° in X-Y direction 1 vertical main spindle (milling unit) HSK 63: 9 kW OPTION: Drilling and milling unit with 4 horizontal spindles (cross spindle) BARCODE READING SYSTEM – PROFESSIONAL PACKAGE