Ekscentrinis presas

PRESSIX T160 CNR6

Būklė: beveik kaip naujas (naudotas), BeCentrovali šlifuoklis ESTARTA 301 CNC Gjdjxfqzmspfx Afqebt

Būklė: naujas, Gamybos metai: 2024, Funkcionalumas: visiškai funkcionalus, slėgis: 16 juosta, įėjimo dažnis: 50 Hz, įvesties srovės tipas: trifazis, temperatūra: 400 °C, įėjimo įtampa: 6 000 V, sukimosi greitis (min.): 1 500 aps./min, sukimosi greitis (maks.): 1 500 aps./min, aušinimo tipas: oras, Industrial Steam Turbogenerator Howden – Model KK&K TWIN CA46, NEW, never installed and never commissioned, still covered by manufacturer’s warranty. Following a revision of the long-term industrial strategy, a Howden KK&K TWIN CA46 steam turbogenerator, complete as per original OEM supply, is now available for sale. The unit is NEW, manufactured and fully tested at OEM level, but never installed or put into service. It is still covered by the manufacturer’s warranty and is stored in a controlled indoor environment. Immediate availability allows you to bypass the usual production lead times, which for this kind of equipment are typically 24–36 months. Main supply includes: - Steam turbine on skid with integrated gearbox - Synchronous generator supplied separately Turbine technical configuration: - Model: KK&K TWIN CA46 - Dual casing turbine (Steam Part A + Steam Part B) - 3-shaft integrated gearbox (2 pinions + central gear) - Controlled steam extraction between HP and LP sections (included) Main design conditions: - Inlet steam pressure (HP): 16 bar(a) - Inlet steam temperature: 400 °C - Electrical output at terminals: up to 1,595 kW - Nominal speed: 1,500 rpm Electric generator: - 3-phase synchronous generator - Rated power: 1,994 kVA - Voltage: 6 kV – Frequency: 50 Hz - Cooling: IC31, air - Brushless execution, prepared for parallel grid operation Systems included: - Integrated oil system in base frame - Main mechanical oil pump and auxiliary electric oil pump - Local control panel on skid - Control and protection panel equipped with Siemens SIPROTEC 5 - Electronic speed and pressure governor - Independent overspeed protection device Gbjdpfx Asyidvdsfqjt - Turbogenerator simulation model ENC-RfG Typical applications: - Industrial cogeneration plants - Process steam energy recovery - Biomass and waste-to-energy plants - Combined production of electricity and process steam Status and conditions: - Condition: NEW - Year of manufacture: late 2024 - Never installed – never commissioned - Still under manufacturer’s warranty - Complete OEM technical documentation available - Possibility of installation and commissioning with manufacturer support Possible fields of application: - Biomass and waste-to-energy plants, for production of electricity and process steam, with immediate unit availability — no multi-year production lead times - Industrial cogeneration (CHP) in plants with continuous process steam usage (paper, food, chemical, and manufacturing industries) - Revamping/repowering of existing plants, as a fast-track alternative to new OEM supplies with 24–36 month delivery times Price: Upon request. Further technical information and documentation available upon request.

Gamybos metai: 2016, būklė: paruoštas naudoti (naudotas), The Coiltech Decoiler Straightener Feeder System is a compact feed line for presses. Strip width: 600 mm, material thickness: up to 6.5 mm, straightening rolls: 7 x 115 mm, decoiler load capacity: 6,000 kg, inner diameter (min-max): 470–520 mm. Connected load: 7.5 kW; supplied with documentation. Gbedei El Ucopfx Afqst

Būklė: naujas, Funkcionalumas: visiškai funkcionalus, Gamybos metai: 2025, lazerio galia: 6 000 W, X ašies eiga: 3 030 mm, Y ašies eiga: 1 520 mm, Z ašies eigos atstumas: 310 mm, bendras ilgis: 9 500 mm, bendras plotis: 4 500 mm, bendras aukštis: 2 050 mm, Įranga: CE žymėjimas, apsaugos šviesos užtvara, aušinimo blokas, avarinis stabdymas, centralizuota tepimo sistema, dulkių šalinimas, dūmų ištraukimas, purkštukų keitiklis, VS-3015CE 6KW pluošto lazerinė lakštinio metalo pjovimo staklės Darbinis plotas (mm): 3000×1500 X ašies eiga (mm): 1520 Y ašies eiga (mm): 3030 Z ašies eiga (mm): 310 X/Y ašių pozicionavimo tikslumas: ≤0,03 mm/m Gsdpfxjv Ngras Afqsbt X/Y ašių pakartotinio pozicionavimo tikslumas: ≤±0,02 mm Maks. sintezuotas pozicionavimo greitis: 150 m/min Maks. pagreitis: 2G Dvipusis valdymo pultas, adaptyvus daugiakampis išdėstymas, paprastas išardymas ir galima transportuoti standartiniame 40HQ konteineryje. Pramoninės klasės specialus oro kondicionierius – pastovi temperatūra ir drėgmė, užtikrinanti stabilius veikimo parametrus. Automatinė tepalo ir alyvos įpurškimo sistema, protingas oro slėgio stebėjimo įrenginys ir apsaugos nuo susidūrimo detektorius užtikrina išmanią apsaugą.

Būklė: naudotas, Sheet width: 250 mm Coil outer diameter: 1400 mm Load capacity: 2500 kg Sheet thickness: 2 ... 4 mm Straightening speed: 2.5 ... 15 m/min Decoiler: Expanding range mm Total power requirement: 1 + 4 kW Machine weight: approx. 1.8 t Space requirement: approx. (specify dimensions) Decoiler MHR 250/4: Max. coil diameter: 1400 mm Inner coil diameter: 450 - 530 mm Unbraked decoiler with pressure roller Straightening machine MR 250/4: Strip entry height: 1250 mm Gbodpjfn Aqmsfx Afqot The system has been dismantled, inspected, and freshly repainted.

Būklė: paruoštas naudoti (naudotas), Pressing force: 1600 kN, throat depth: 450 mm, installation height: 560 mm, ram stroke: 8–160 mm, control system: SCHMERSAL SEPG 05.3.2.0.22/95, weight: 16.2 t, including documentation. Gedpfxshz Ua Se Afqjbt

Būklė: naudotas, Gamybos metai: 2007, Pressure: 200 t Gjdpfx Asvbk Rwefqsbt Throat depth: 510 mm Stroke: 16 - 160 mm Ram adjustment: 120 mm Table surface: 1500 x 1000 mm Table height above floor: 900 mm Pass-through opening in table: 800 x 250 mm Ram surface: 1000 x 700 mm Pin hole in ram: 65 x 110 mm T-slot width: 28 mm Adjustable stroke rate: 30 - 120 strokes/min Hydraulic unit oil capacity: 5 l Installation height (max. stroke, ram adj. top): 600 mm Installation height (stroke bottom, ram adj. top): 440 mm Total power requirement: 32.2 kW Machine weight approx.: 24 t Required space (WxDxH): 2.85 x 3.1 x 3.65 m - Hydraulic clutch - Fixed table - Hydraulic overload protection in the ram - Hydraulic connecting rod clamping - Motorized ram height adjustment, 120 mm, with digital display of set ram height, rapid and creep speed - Fully automatic stroke adjustment, adjustable range 16 - 160 mm - Ram weight compensation - Electronic top dead center correction - Planetary gearbox - Central oil circulation lubrication - Separate control desk with SIMATIC S7/300 screen control - Press force measuring device - Reversing switch (return stroke) - Additional operating mode "setup/creep speed" - Electric stroke counter - Electric preset counter - Electric travel limitation of the connecting rod pin - Electronic cam controller - Infinitely adjustable drive (frequency-controlled) - 2 power sockets - Clamping plate - Temperature monitoring of main bearing / support bearing / connecting rod bearing - Operating hours counter - Oil cooler - Set of vibration-damping elements Additional equipment: Electronic roller feeder ebu EVX 500 Feed width: 10 - 500 mm Material cross-section: max. 1,600 mm² Material thickness: 0.2 - 5.0 mm Number of rollers: 2 Roller diameter: 100 mm Intermittent ventilation: up to over 300 l/min Feed length: 1.0 - 9,999.9 mm Feed speed: max. 150 m/min

Būklė: beveik kaip naujas (naudotas), Gamybos metai: 2011, Funkcionalumas: visiškai funkcionalus, veikimo valandos: 1 013 h, X ašies eiga: 620 mm, Y ašies eiga: 520 mm, Z ašies eigos atstumas: 460 mm, valdiklių gamintojas: Siemens, stalo ilgis: 1 100 mm, stalo plotis: 560 mm, valdiklio modelis: 840d SL ShopMill Operate, sukimosi greitis (maks.): 12 000 aps./min, veleno veikimo valandos: 203 h, For sale is a machining center from the manufacturer Spinner, model P3-620. Gbedpet Sftwjfx Afqet The machine is equipped with an internal double-pallet changer, allowing setup operations during machining. Noteworthy features include only 203 spindle hours and the machine’s excellent condition. Technical data: Year of manufacture: 2011 Control: Siemens 840d-SL ShopMill Operate Spindle speed: 12,000 rpm Spindle taper: SK 40 Table dimensions: 1,100 x 560 mm Travel X: 620 mm Travel Y: 520 mm Travel Z: 460 mm Tool changer: 32-position (chain) Tool change arm: double arm Pallet changer: double (180°) Additional equipment: - Machine lighting - Chip conveyor in the milling area - Scraper belt chip conveyor with coolant system - Belt filter system with 40 bar high-pressure coolant supply - Hydraulic oil cooling system - Rotary union on the table Upon request and for an additional charge, loading and transport can be arranged throughout Europe. Prices are subject to VAT. Inspection is possible by appointment. Please contact us—our team looks forward to assisting you. Trade-in or exchange possible! Buying & Selling Machinery PURCHASE / SALE OF PRODUCTION AND METALWORKING MACHINES & MORE Are you looking for a high-quality yet affordable metalworking machine for your production, or would you like to sell yours? For further information or contact options, please visit our website.

Būklė: naudotas, Gamybos metai: 1996, Pressure: 80 t Throat depth: 320 mm Stroke: 6 - 118 mm Strokes per minute: 30 - 80 spm Ram adjustment: 70 mm Table area: 830 x 610 mm Ram area: 650 x 400 mm Frame gap (towards rear): 630 mm Total power requirement: kW Machine weight approx. 8.1 t Space requirement approx. W 1.2 x D 1.9 x H 3.3 m Equipment/features: - with gear drive - fixed table - automatic stroke adjustment - automatic ram adjustment - hydraulic overload protection - ejector - centralized grease lubrication Gbodpetycdkjfx Afqot - cover plate for drop hole - stepless speed control via frequency inverter - The machine will be technically overhauled and inspected in our facility and will receive a new control cabinet with safety control system and touchscreen - current accident prevention inspection (UVV) with brake time measurement

Gamybos metai: 2015, būklė: paruoštas naudoti (naudotas), - USATA - MACCHINA TAGLIO LASER FIBRA CON CAMBIO PALLET CORSA ASSE X: 3048 mm CORSA ASSE Y: 1524 mm CORSA ASSE Z: 70 mm CARICO MASSIMO AMMESSO: 750 Kg/m AREA DI LAVORO: 3000 x 1500 mm SORGENTE: IPG YLS-4000 ; 4000 W UNITÀ DI CONTROLLO: ByVISION ACCESSORI: VOLANTINO PORTATILE NOTA: CAMBIO UGOLETTI AUTOMATICO Gbedpfx Afovcr Tpsqst