Wmw pirkti naudotą (455)

Būklė: naudotas, Technical Details: Grinding length: 1000 mm Grinding width: 315 mm Workpiece height: 390 mm Table speed: 2.5–25 m/min Table clamping surface: 250 x 1000 mm Distance table – spindle centre: 550 mm Grinding wheel dimensions: Ø max. 315 x 13–63 x bore Ø 75 mm Control voltage: 220 / 50Hz V/Hz Total power requirement: 10.5 kW Machine weight approx.: 5.0 t Machine dimensions approx. LxWxH: 3.35 x 1.5 x 2.10 m The machine is currently located in the technical department. Gijdpfou Ngn Sex Agdjp

Būklė: naudotas, Technical details: Pressing force: 2.3 t Stroke: 280 mm Throat depth: 155 mm Ram stroke - max.: Forward: 0.08 m/sec Installation height with clamping plate ram/top: 355 mm Distance table/ram: max. 355 mm Clamping plate on table: 280 x 280 mm Pass-through opening in table: Ø 100 mm Ram speed forward: 0.08 m/s Ram speed return: 0.32 m/s Pin hole in ram: Ø 20 x 45 mm Height above floor: 725 mm Gjdpfx Ageu Nfwlodsip Total connected load: 1.1 kW Machine weight approx.: 0.5 t Machine dimensions approx. LxWxH: 0.6 x 0.7 x 1.6 m Press with mechanical two-hand operation. Pressure test up to 2.3 t performed. Good condition.

Būklė: naudotas, Gamybos metai: 1991, Technical Details: Pressure: 160 t Stroke: 500 mm Throat depth: 360 mm Maximum ram stroke: 500 mm Gedpfx Asw D Awmjgdsip Distance table/ram: 800 mm Clamping plate on table: 1250 x 630 x 100 mm Pass-through hole in table: 4x Ø62 mm Ram speed, forward: 200 mm/s Ram speed, return: 125 mm/s Ram surface: 450 x 850 mm Pin hole in ram: 49 mm Height above floor: 810 mm Total power requirement: 17 kW Machine weight approx.: 7,200 kg Approx. dimensions (LxWxH): 2.1 x 1.4 x 3.4 m

Būklė: naudotas, Technical details: Pressing force: 25 t Clearance between uprights: 360 mm Stroke: 500 mm Installation height, table/ram at top: 800 mm Throat depth: 360 mm Ram stroke: 500 mm Ram advance speed: 0.200 m/s Ram return speed: 0.45 m/s Table size: 630 x 500 x 71 mm Table opening: Ø 182 mm Ram clamping surface: 450 x 360 mm Pin hole in ram: Ø 32 x 72 mm Ram diameter: Ø 125 mm Height above floor: 710 mm Total power requirement: 12.5 kW Machine weight approx.: 2.4 t Machine dimensions approx. (LxWxH): 1.7 x 1.1 x 2.95 m Operation via two-hand control console (single-hand operation possible in setup mode) Continuous and single stroke modes TÜV certified until 05/2024 i.D. Gsdpsu U D I Refx Agdoip *

Būklė: naudotas, Gamybos metai: 1984, Technical details: Grinding diameter min/max: 8 / 40 mm Spindle speed: 3,000 rpm Total power requirement: approx. 1.2 kW Machine weight approx.: 0.24 t Machine dimensions approx. LxWxH: 0.7 x 0.9 x 1.3 m The grinding spindle is equipped with two hand levers: Left working area = manual grinding device for small shank drills Right working area = pivoting device for conical shank drills Cutting angle max. 180° Small drill pivot arm: relief angle 5° - 9°; drill Ø 8 - 15 mm manually adjustable; grinding wheel cup wheel Ø 200 x 40 mm with bore Ø 32 mm Gsdpfxsu Ng Irs Agdjip Large drill pivot arm: relief angle 5° - 9°; max. drill Ø 400 mm; division 6x with manual indexing; currently mounted grinding wheel Ø 180 x 31 mm with bore Ø 32 mm Grinding types: Standard grind, DK grind, centering grind, spiral countersink, multiple-step drills

Būklė: naudotas, Techninės detalės: Plotis: 1270 mm Gylis: 1000 mm Aukštis: 1600 mm Godpfx Aju N Ea Hsgdeip Yra 3 vnt. prispaudimo kampainių T-slotas pagal DIN 650: a=35 mm; b=60 mm; c=27 mm; h=65 mm Kaina už vieną kampainį

Būklė: labai geros būklės (naudotas), Skersmuo: 400 mm Ilgis: 500 mm Gedpfoyt Sqasx Agdoip

Būklė: labai geros būklės (naudotas), Gamybos metai: 1986, Maks. tekinimo diametras virš staklių pagrindo: 300 mm Maks. tekinimo diametras virš galinio slankiklio: 250 mm Maks. tekinimo ilgis: 630 mm Gsdpfx Agoyt Spvedsip Atstumas tarp centrų: 1000 mm

Būklė: naudotas, Technical Details: Drilling capacity in steel (diameter): 40 mm Giodjwid Uwepfx Agdjp Throat depth: 360 mm Drilling stroke: 280 mm Spindle taper: MT 5 Spindle speed: 32 - 1400 rpm Feed rate: 0.11 - 1.73 mm/rev Connected load: 6 kW Max. distance spindle/table: 750 mm Table clamping surface: 780 x 650 mm Vertical table adjustment: 800 mm Column diameter/size: 230 x 950 mm Approx. machine dimensions (LxWxH): 1.1 x 0.8 x 2.8 m Approx. machine weight: 1.5 t With right- and left-hand thread cutting reverse.

Būklė: naudotas, Technical details: Turning length: 630 mm Swing diameter over cross slide / rear cross slide: 250 mm Center height over bed: 270 mm Center distance: 900 mm Spindle bore: 26 mm Stepless speed range: 1.8 - 450 rpm Return speed: 23 / 32 / 46 / 370 / 510 / 740 rpm Cross feed: 0.07 - 1.11 / 36 steps mm/rev Longitudinal feed: 0.063 - 0.63 / 12 steps mm/rev Tailstock quill taper: MT 5 Quill stroke: 250 mm Giodpevbh N Rsfx Agdjp Total power requirement: 7.0 kW Machine weight approx.: 3.9 t Machine dimensions approx. LxWxH: 3.2 x 1.2 x 1.8 m Application: Primarily for relief turning and relief grinding of cutting tools (especially hobs with or without thread profile). Relief turning and relief grinding is possible from the front, rear, and axial directions of the machine. Main drive via 8-speed manual gearbox. Feed gearbox designed as a 12-stage manual gearbox. Swivel range of the rear cross slide = 360° Swivel range of the cross slide = 360° Equipment: Lathe chuck driver disc Ø 210 mm with fixed center Fixed center in tailstock with 4 machine feet 3-jaw chuck Ø 250 mm i.d.

Būklė: naudotas, Gamybos metai: 1979, Technical details: Grinding diameter min/max: Mounting: Ø 200 x 32 mm Spindle speed: 3,000 rpm Giedpfxsu Ng Nco Agdep Total power requirement: approx. 1.2 kW Machine weight approx.: 0.24 t Machine dimensions approx. LxWxH: 0.7 x 0.9 x 1.6 m The grinding spindle is equipped with two hand levers: Left working area = Hand grinding attachment for small shank drills, grinding wheel currently Ø 120 x 30 mm; mounting = Ø 32 mm; speed 3,000 rpm; includes grinding rest Right working area = Swivel attachment for tapered shank drills; cup grinding wheel currently Ø 160 x 30 mm; mounting = Ø 32 mm; speed 3,000 rpm. Point angle for double-edged drills max 180° and for triple-edged 120° Relief angle 5° - 9°; drill Ø 8 - 40 mm, possible grinding types e.g.: standard grind, cross-point grind, center grind, spiral grind, step drill grind Machine lighting included

Būklė: naudotas, Technical details: X-axis travel: 450 mm Y-axis travel: 150 mm Z-axis travel: 400 mm Distance from column to table edge, min./max.: 100 / 250 mm Spindle speed range: 25, 44, 78, 130, 228, 400 / 6 steps rpm Feed rate X/Y: 10 - 100 / 8 steps mm/min Table size: 990 x 300 mm Godpfxeu Nc Nlo Agdeip Clamping surface: 800 x 195 mm Table swivel +/-: 30° Connected load: not specified kW Weight approx.: 1,200 kg Machine dimensions (LxWxH): approx. 1.5 x 1.3 x 1.5 m Horizontal milling machine, currently fitted with a 32 mm tool arbor and a gear cutter. Machine vice included.

Būklė: naudotas, Technical details: X travel: 1000 mm Y travel: 350 mm Z travel: 400 mm Distance from column to table edge: min. 150 / max. 550 mm Spindle speed range: 28 - 1400 rpm / 18 steps Tool holder: SK40 Spindle head swivels left/right: 90° and forwards/backwards: 45° Feed rate (X/Y axis): 16 - 800 mm/min / 18 steps Table size: 1600 x 400 mm Gedpfxov Sz Dij Agdoip Clamping surface: 1400 x 330 mm Total power requirement: 14.5 kW Approx. weight: 4000 kg Machine dimensions (LxWxH): approx. 2.0 x 2.4 x 1.85 m Horizontal milling machine, retrofitted with vertical milling head

Būklė: naudotas, Technical details: Grinding length: 300 mm Grinding spindle - rotatable: 350° Grinding spindle head adjustable: vertical: 250 mm Spindle head adjustment: transverse: 230 mm Grinding spindle head adjustable: tiltable +/-15° Grinding diameter: Ø 250 mm Spindle speeds: 2200 - 3500 - 5200 rpm Work table: W: 120 x L: 950 mm Table movement: upper table inclined: right/left 45° mm Table travel: maximum table travel: 500 mm (manual) Magnetic chuck surface: 305 x 130 x 100 mm Grinding wheel dimensions: cup wheel 125 x 20 Ø 32 mm Gjdpfou Ng Npsx Agdoip Total power requirement: 1.8 kW Machine weight approx.: 1.0 t Machine dimensions approx. LxWxH: 1.6 x 1.3 x 1.7 m Hydraulic dimensions: 600 x 550 x 870 mm Accessories: Universal clamping head taper MK5 Drill grinding fixture Ø 10 mm

Būklė: naudotas, Gamybos metai: 1979, Technical Details: Swing diameter over bed: 540 mm Turning length: 630 mm Center distance: 900 mm Center height over bed: 270 mm Center height over rear slide: 138 mm Swing diameter over rear slide: 250 mm Longitudinal travel: 700 mm Cross travel: 80 / 75 mm Spindle speeds: 1.8 - 450 rpm stepless across 8 ranges Clamping diameter: 26 mm Feed range X-axis: 12 steps / 0.063 - 0.63 mm/rev Feed range Y-axis: 36 steps / 0.070 - 1.11 mm/rev Tailstock quill: MK5 Tailstock quill stroke: 250 mm Total connected load: 7.0 kW Machine weight approx.: 3.76 t Machine dimensions approx. (LxWxH): 3.2 x 1.2 x 1.8 m Application: Primarily used for reverse turning and relief grinding of cutting tools (especially hobbing cutters with and without thread pitch). Reverse turning and relief grinding is possible from the front side, the rear side, and in the axial direction of the machine. Main drive via 8-step manual gearbox. Feed gearbox designed as 12-step manual gearbox. Rear slide swiveling range = 360° Cross slide swiveling range = 360° Chuck is a taper disc Ø 200 mm with MK5 Equipment: Mandrel Ø 49.5 x 400 mm Measuring system ARBAH-L 3+1 Frequency inverter FRENIC 5000G11 3-jaw chuck Ø 250 mm Gsdpsvbhv Refx Agdoip In stock. *

Būklė: naudotas, Technical Details: Number of spindles: 4 Drilling capacity in steel (diameter): 30 mm Drill stroke: 200 mm Drill spindle Morse taper: MT3 Spindle overhang: 350 mm Spindle center distance: 490 mm Spindle head adjustment: 500 mm Feed rates: 0.07; 0.15; 0.25; 0.33 / 4-step mm/rev Feed: manual and automatic Spindle speed: 70 ... 1,600 / 8-step rpm Distance spindle/table: max. 430 mm Distance spindle/table: min. 180 mm Gjdou Idt Nopfx Agdjip Table surface: 1820 x 400 mm Table adjustment: 250 mm with hand crank Total power requirement: 10.8 kW Machine dimensions (approx. LxWxH): approx. 1.0 x 2.1 x 2.8 m All spindle heads with right and left rotation Drill heads 1 to 3 with right and left rotation, without tapping function Drill head 4 with automatic tapping function, Röhm chuck up to Ø 33 mm All drill heads and the table are height adjustable. Equipment: Coolant supply Int. diameter

Būklė: naudotas, Technical details: Shearing capacity: 1 mm Max. blank diameter: 1000 mm Shearing capacity: 1 mm Max. blank diameter: 1000 mm Machine weight approx.: 0.2 t Machine dimensions approx. LxWxH: 2.0 x 0.5 x 1.4 m Application: Manual cutting of round sheet steel parts Upper blade: Ø 69 mm x 11 mm; vertical adjustment 25 mm with hand lever Lower blade: Ø 74 x 15 mm; adjustment: NONE = fixed Gsdsu Icqyspfx Agdoip Centering holder with die Material is manually moved: vertical stroke 15 mm with hand lever, horizontal feed 500 mm manually.

Būklė: naudotas, Gamybos metai: 1987, Technical details: Spindle diameter: 120 mm X-axis travel: 2750 mm Y-axis travel: 1500 mm Z-axis travel: 1250 mm Gisdpfxsu Idrfo Agdep B-axis (table): 360° W-axis (spindle longitudinal): 900 mm CNC control: TNC 155 contouring control Tool holder: SK50 Table load capacity: 6.3 t Table size: 1600 x 1400 mm Table rotation: 360° Boring spindle speed: 3 – 1000 rpm Total power requirement: 100 kW Control cabinet dimensions (LxWxH): 650 x 2800 x 2100 mm Machine dimensions (LxWxH): see list (m) Machine weight approx.: 15.0 t Contouring control Planer slide feed 210 mm (U-axis) Hydraulic unit Extension arm with control panel Heidenhain measuring system

Būklė: naudotas, Technical specifications: Number of spindles: 4 Drilling capacity in steel (diameter): 2-16 mm Drilling stroke: 140 mm Drill spindle Morse taper: MT 3 Spindle overhang: 280 mm Spindle distance: 455 mm Spindle head adjustment: 250 mm via hand crank Feed rate: 0.08 - 0.12 - 0.20 - 0.31 mm/rev, 4 steps Feed: automatic + manual Spindle speed: 180 - 2000 rpm, 8 steps Distance spindle/table: min. 3x 140 mm and 1x 260 mm Distance spindle/table: max. 3x 700 mm and 1x 820 mm Table size: 1800 x 350 mm Table adjustment: 300 mm via hand crank Total power requirement: 6.3 kW Machine weight approx.: 2.4 t Machine dimensions (LxWxH) approx.: 2.1 x 0.9 x 2.2 m Application: Drilling, countersinking, reaming, and tapping. Each drill spindle is equipped with its own drive motor. Equipment: Foot pedal/control Gjdpfx Ageu Idugedsip Hand crank

Būklė: naudotas, Techniniai duomenys: x eiga: 500 mm y eiga: 380 mm Giodpfx Aju Nc R Nogdjp z eiga: 330 mm Valdymas: Siemens 840 D / 810 D Veleno kūgis ISO: vertikalus/horizontalus: 40 Stalo tvirtinimo paviršius: 400x800 fiksuotas mm Veleno apsukos - bepakopės: vertikalios/horizontalios: 35–1800 aps./min. Veleno galva pasukama į kairę ir dešinę: 90° Spartusis važiavimas X, Y: 3,15 m/min. Spartusis važiavimas Z ašis: 1,6 m/min Pastovus padavimas: X/Y/Z: 6,3–1250 Bendras galios poreikis: 7,4 kW Mašinos svoris apytiksl.: 1,8 t Mašinos matmenys apytiksl. IxPxA: 1,8 x 2,2 x 1,8 m Valdymo spintos matmenys IxPxA: 0,5 x 0,85 x 2,1 m Mašina 2002 m. buvo perstatyta, įdiegta moderni Siemens 840D/810D shopmill valdymo sistema. - Reguliuojamas eiga per atraminį vežimėlį: 440 mm Įranga: - Aušinimo sistema - Valdymo pultas su svirtimi Priedai: - įvairios spaustuvių įvorės - įvairūs SK 40 tvirtinimai - įvairūs frezavimo laikikliai gl.

Būklė: naudotas, Gamybos metai: 1981, Technical details: Godpfju Nc Hkex Agdoip x-travel: 400 mm y-travel: 420 mm z-travel: 380 mm Table size: 710 x 400 mm Max. table load: 120 kg Spindle speed range: 45 - 2240 / 18 steps rpm Feed (stepless): 6.3 - 600 / 2 stepless mm/min Quill stroke vertical: 100 mm Quill stroke horizontal: 100 mm Spindle taper vertical/horizontal: SK 40/SK 40 Spindle head swivels left and right: 90° Distance table/horizontal spindle: min./max.: 200 / 325 mm Distance table/vertical head: min./max.: 150 / 730 mm Total power requirement: 5.5 kW Machine weight approx.: 1,950 kg Machine dimensions (LxWxH): 1.7 x 1.4 x 1.9 m Control cabinet dimensions: 850 x 500 x 1500 mm Including machine feet and operating manual

Būklė: naudotas, Technical details: Z-axis travel: 400 mm Speed range: max. 3,000 rpm, stepless Feed, stepless: no data Quill stroke, vertical: 100 mm Spindle taper: MK2 Table size: 445 x 315 mm Distance table to spindle nose: max. 520 mm Table travel, longitudinal: 250 mm Table travel, cross: 330 mm Table height above floor: 920 mm Total power requirement: 1.6 kW Machine weight approx.: 1,500 kg Machine dimensions (LxWxH): 1.3 x 1.1 x 2.0 m Application: Milling and drilling of elongated holes The drill head is equipped with a precision dial gauge for depth indication. 5x T-slots according to DIN 650: a=10; h=18; b=18; c=8 mm Equipment: Digital two-axis display ACU-RIDE Giedpfxov A S Efs Agdjp

Būklė: naudotas, Technical Details: Pressing force: 40 t Throat depth: 365 mm Distance table/ram: 800 mm Ram stroke – max.: 500 mm Ram return speed: 0.45 m/sec Ram advance speed: 0.10 m/sec Ram surface: 450 x 360 x 74 mm Table surface: 630 x 500 x 73 mm Table through opening: Ø 205 mm Giodpfx Ageu Nfuqodsp Table height above floor level: 720 mm Total power requirement: 13.0 kW Machine weight approx.: 3.2 t Machine dimensions approx. LxWxH: 1.7 x 1.1 x 3.0 m Additional technical features: - Overrun time: 443 ms - Overrun distance: 9 mm - Last machine inspection: May 2020, valid for 1 year

Būklė: naudotas, Gamybos metai: 2004, Techniniai duomenys: Stalo ilgis: 4000 mm Stalo plotis: 2000 mm Maks. plokštės storis: 100 mm Stalo aukštis nuo grindų: apie 860 mm Bendras svoris: 5,6 + 0,5 t Godpfeu Nkxuox Agdoip Išmatavimai (IxPxA): 4,0 x 2,2 x 0,1 m Suvirinimo stalas / Kainodara: 0,50 EUR/kg su pagrindu ir 6 vnt. kojų atramų

Būklė: naudotas, Accessories for, e.g., a BFT 130 table-type boring mill. Gjdju Nlgyopfx Agdjip The spindle head and swivel angle can each rotate 360° around their respective axes. Two swivel planes. The set angles can be read off from circumferential scales. Maximum speed: 600 rpm. Spindle taper: ISO 50. Weight: approx. 270 kg Including connecting piece for SK 50 quill/head drive.