Sinter pirkti naudotą (121)

Sąlyga: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2023, įvesties srovės tipas: Oro kondicionierius, Electrically heated roller sintering furnace, manufacturer Riedhammer Model: TR 18/4x33/10-E 90 Condition: As new Length of debinding zone: 6.12 m Length of heating/holding zone: 6.12 m Length of cooling zone: 6.12 m Total furnace length without conveyor: approx. 18.4 m Total furnace length with infeed/outfeed: 20.4 m Overall furnace width: 3.5 m Overall furnace height: approx. 2.5 m Furnace clear width: 1,540 mm Usable width: 4x 330 mm Usable height from top of roller: 100 mm Iiodpfx Abop T Th Hsksk Roller pitch: approx. 85 mm Roller diameter: approx. 50 mm Number of drives for furnace conveyor (controlled): 3 units Number of control zones: 34 Furnace connected load: approx. 476 kW Maximum thermocouple temperature: 900 °C Maximum temperature: 930 °C Power supply: 400/230V, 50Hz Cooling water consumption: approx. 50 m³/h

Gamybos metai: 2020, Sąlyga: beveik kaip naujas (naudotas), Funkcionalumas: visiškai funkcionalus, Fully Automatic Sintering Continuous Furnace System Brand: Sarnes Model: 600-G/CQI-9 Year of Manufacture: 2020 (Commissioned 2021) Programmable, with online diagnostic system. Fuel: Natural gas Operation with hydrogen and nitrogen (N2+H2) integrated Iiedpfx Aoxfcdyebksk The system has had very limited operation and is in excellent condition. Offer / Quotation Date: 18.1.19 620 mm belt width, gas-heated, N2/H2 operation, LED burnout zone, quench cooling (Pos. 2), flameless discharge with ceramic muffle, Heating: low NOx RS Rekudrall burners with SiSiC burner tubes, installed heating capacity 320 kW across 8 zones, double thermocouples, 100 mm usable height. LED 3 dewaxing zone ("low energy dewaxing" – utilization of chemically bound energy in waxes and improved burnout conditions, especially for heavy PM parts (>0.9kg)); Dimensions: - Infeed table: 2 m (setpoint/actual belt speed adjustment) - Burnout zone LED3: 1.5 m - Length sintering zone: 7.5 m - Length quench cooling: 1 m - Length convective cooling zone: 2 x 4 m - Flameless discharge with air shower: 2 m - Outfeed table: 2.7 m - Total system length: 23.7 m - Width: 2.3 m Connection values: Heating: installed capacity 320 kW Natural gas: 25 m³/h (80 mbar) N2: 45–65 m³/h (max. 80 mbar) H2: 0.5–15 m³/h (80 mbar) Cooling water: 3–5 m³/h (non-pressurized; temp.

Sąlyga: beveik kaip naujas (parodų įrenginys), Funkcionalumas: visiškai funkcionalus, Gamybos metai: 2019, temperatūra: 1 300 °C, ruošinio svoris (maks.): 10 kg, ruošinio ilgis (maks.): 250 mm, ruošinio plotis (maks.): 183 mm, ruošinio aukštis (maks.): 150 mm, No reserve price – guaranteed sale to the highest bidder! HIGHLIGHTS - Complete end-to-end solution including wash station and sinter unit (sinter core unit not included) - Machine barely used - Suitable for printing parts made of 17-4 PH stainless steel, D2/A2/H13 tool steel, and copper TECHNICAL DETAILS Printing process: Atomic Diffusion Additive Manufacturing (ADAM) Build volume: 300 x 220 x 180 mm Layer thickness: 50 µm and 125 µm after sintering Maximum part size: 250 x 183 x 150 mm, 10 kg Software: Eiger Cloud Sintering Sintering capacity: 3,020 cm³ (184 in³) Sintering area: 348 cm³ Sintering time: 26 hours Compatible gases for sintering: Argon, Argon-hydrogen mixture Maximum temperature: 1,300 °C Washing Washing capacity: 18,356 cm³ Washing volume: 356 x 254 x 203 mm Basket: stainless steel wash basket Fluids: Opteon SF79, Opteon SF80 or Tergo metal cleaning fluid MACHINE DETAILS Dimensions (printer): 575 x 467 x 1,120 mm Iiodpfov Hpi Aox Abkek Weight (printer): 75 kg Dimensions (wash unit): 609 x 685 x 1,067 mm Weight (wash unit): 136 kg Dimensions (sinter unit): 1,270 x 510 x 720 mm Weight (sinter unit): 136 kg EQUIPMENT - Printer + Wash-1 unit + Sinter-1 unit (without sinter core unit) - Dual-nozzle print system - Heated print chamber - Vacuum-sealed build plate - Automatic leveling

Gamybos metai: 2023, Sąlyga: naujas, Electrically heated twin-track pusher plate kiln, manufacturer Riedhammer Type: TP12.75/2x20/15-E-145 Condition: As new Total furnace length: 15.5 m Furnace width: 3.6 m Power supply: 400/230V, 50 Hz Connected load: 17 kVA Permissible voltage fluctuation: 10% Permissible frequency fluctuation: 1% PLC: SIEMENS/Comfort Panel TP1500-15 Product dimensions (L x W x H) incl. pusher plate: 200 x 200 x 101 mm Iodpop T T Hnsfx Abkjik Max. temperature debinding zone (4 segments): 650 °C Max. temperature pressure equalizing zone (1 segment): 750 °C Max. temperature main firing zone (6 segments): 1450 °C Max. temperature cooling module 1: 600 °C Max. temperature cooling module 2: 300 °C Min. push time: 8 min Max. push time: 30 min Number of carrier plates: 266 units Channel height: 105 mm

Sąlyga: geras (naudotas), Debinding and Sintering Furnace, manufacturer Nabertherm, in very good condition Type: LH 280/13 DBS Max. temperature: 1300°C Internal dimensions (W x D x H): 750 x 750 x 500 mm External dimensions (W x D x H): 1250 x 1750 x 2100 mm Loading weight: max. 150 kg Connected load: 44 kW Heating: 5-sided heating Control zones: 1 Weight: 700 kg Voltage: 400 V 3/N Current consumption: 63 A - An air heater located beneath the furnace allows preheated air with temperatures up to 400°C to be introduced into the furnace chamber during the debinding phase. - Adjustable cooling housing with automatic ball valve - Automatic exhaust flap - Automatic flue gas flap - Monitoring of fresh air and exhaust gas flow rates as well as furnace chamber pressure by means of a differential pressure switch. Iisdpfx Asmfn Rujbksk - The furnaces themselves, especially the brickwork, heating elements, and insulation, are in excellent condition with minimal or no operating hours, making them virtually as new. - To operate these furnaces, you will need to implement at least one temperature controller per furnace, a PLC, or a similar control system.

Sąlyga: naujas, Gamybos metai: 2025, CORMAK HBS260 bandsäge zum Schneiden von Rohren, Profilen und Stangen wird in allen Schlossereibetrieben eingesetzt, bei denen Präzision, Qualität und Schnittgeschwindigkeit wichtig sind. Das Modell verfügt über einen schwenkbaren Arm von 0-60°. Die Rahmenkonstruktion sorgt für einen präzisen und leisen Betrieb. Sie verfügt über eine herausnehmbare Spänewanne für eine einfache Reinigung! Maschineneigenschaften Die horizontale Metallbandsäge mit schwenkbarem Arm ermöglicht das Schneiden in einer zur Achse des Werkstücks senkrechten Ebene sowie in jedem Winkel zwischen 0 und 60°. Das zu schneidende Material kann manuell oder mit jedem mechanischen Vorschub zugeführt werden, der Werkzeugvorschub erfolgt automatisch. Die Bandführungen sind mit speziellen Hartmetallplatten und Wälzlagern ausgestattet. Dies wirkt sich entscheidend auf die Bandführung, deren Lebensdauer, Geradheit, Präzision und Schnittqualität aus. Die Hartmetall-Führung minimiert den Verschleiß der Maschine und des Sägeblatts. Die Maschine ist mit einer leistungsstarken Kühlmittelpumpe mit geschlossenem Kühlkreislauf ausgestattet. Der durchgehende Gusssägearm in Kombination mit dem 27 mm breiten Sägeband ermöglicht Serienkopfschnitte von Profilen und Vollmaterialien. Der Schraubstock befindet sich auf einer einstellbaren Basis und ist mit einer Schnellspannvorrichtung ausgestattet. Die Bandführungen sind mit Hartmetallplatten (gesinterte Hartmetalle) und Rollsystem ausgestattet. ZENTRIERTE HARTMETALLFÜHRUNGEN sorgen für die Präzision und Geradheit des Schnitts. Die Form des oberen Gestellbereichs dient als Wanne zur Aufnahme von Kühlmittel und Spänen, die beim Schneiden entstehen. Ein Gusseisentisch mit schwenkbarem Arm sowie ein Bedienfeld auf einem separaten Arm sind am Grundkörper befestigt. Während des Schneidvorgangs ist die Bewegung des Sägebands sowie der Absenkvorgang des Arms die Hauptschnittbewegung. Die Absenkgeschwindigkeit des Arms (Schnittgeschwindigkeit) wird durch einen Hydraulikzylinder geregelt. Die Vorschubgeschwindigkeit lässt sich am Bedienfeld einstellen. Es sind zwei Schnittbandgeschwindigkeiten wählbar: 35 und 70 m/min. In der unteren Armstellung (nach Beendigung des Schnitts) wird der Bandantrieb automatisch abgeschaltet. Die Sicherheit wird durch Bandabdeckungen und Mikroschalter gewährleistet, die den Motor nach Abschluss des Schnittzyklus oder beim Öffnen einer Abdeckung stoppen. Zusätzlich sorgt eine automatische Abschaltung der Maschine beim Bandriss für Schutz. Schnittbandmaß [mm]: 2520 x 27 x 0,9 Bandspannung: mechanisch (manuell) Bandgeschwindigkeiten [m/min]: 35, 70 Einstellbarer Armabwurf: stufenlos – Hydraulikzylinder Schraubstockhöhe [mm]: 860 Sägeraddurchmesser [mm]: 300 Sägerahmenschwenkung [°]: 0-60 Stromversorgung: 3 Phasen 400V Hauptmotorleistung [kW]: 1,1/1,5 Kühlmittelpumpenleistung [kW]: 0,05 Abmessungen inkl. Sockel [cm]: 150x80x140 Gewicht [kg] brutto/netto: 210 / 180 kg *Bitte beachten Sie, dass die Maschine serienmäßig ohne CEE-Stecker geliefert wird, da es verschiedene Ausführungen gibt. Sollten Sie den Stecker wünschen, geben Sie dies bitte vor dem Kauf oder während des Bestellvorgangs beim Verkäufer an. Der Preis ist ein Nettopreis. Versandkosten sind nicht im Preis enthalten. Für weitere Informationen kontaktieren Sie uns bitte telefonisch oder per E-Mail. Wir laden Sie ein, sich mit unserem Angebot auf unserer Webseite vertraut zu machen. Iijdpfxomrnk Ej Abkjk

Sąlyga: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, stalčių skaičius: 8, The item for sale is a storage rack for storing glass panes (160 cm x 255 cm) in crates (8 x 2500 kg): glass, sintered quartz, polycarbonate, furniture panels, stone, or other panel materials. The rack features movable, slightly inclined drawers. Ijdpfx Asgfm I Esbkoik This design allows you to save up to 75% of space, as all drawers are parallel to each other and only 10 millimeters apart. We offer various sizes and capacity versions. Upon request, we can also manufacture a storage rack tailored to your specific requirements and individual preferences. This storage rack is especially recommended for companies in the glass, stone, furniture, and advertising industries that value efficient space utilization.

Sąlyga: naudotas, rida: 206 000 km, galia: 125 kW (169,95 AG), pirmoji registracija: 11/2022, kuro tipas: dyzelinas, bendras svoris: 3 500 kg, spalva: balta, pavaros tipas: mechaninis, emisijos klasė: Euro 6, sėdimų vietų skaičius: 2, krovinio erdvės tūris: 15 m³, krovimo vietos ilgis: 4 430 mm, krovinių skyriaus plotis: 2 180 mm, krovos erdvės aukštis: 1 780 mm, Gamybos metai: 2022, Įranga: ABS, centrinis užraktas, elektroninė stabilumo programa (ESP), oro kondicionavimas, suodžių filtras,

Sąlyga: naudotas, veikimo valandos: 34 000 h, Technische Spezifikationen & Leistungsdaten Diese gebrauchte Komplettabfüllanlage ist für die aseptische Kartonverpackung im Tetra Pak Prisma 0,33L-Format konfiguriert. Sie wurde um bewährte Komponenten von Tetra Pak entwickelt und bietet eine kompakte, zuverlässige Lösung für hochwertige Industrieabfüllung und Getränkeproduktion. Die Linienkonfiguration integriert die Funktionen Füllen, Verschließen und Verpacken mit reibungsloser Gebindehandhabung für einen stabilen Betrieb und gleichbleibende Leistung. Leistung: 7.500 Stück/Stunde Format: 0,33L Prisma (quadratisch) Gebindetyp: Karton (Tetra Pak Prisma) Linienkonfiguration: TBA19 (Füller) + TCA45 (Verschließer) + TCBP70 (Verpacker) Füllermodell: TBA19 Verschließermodell: TCA45 Verpackermodell: TCBP70 Betriebsart: Aseptische Abfülllinie für lang haltbare Getränke Iiedpfx Abox E U Akokek Hersteller: Tetra Pak Moderne Automatisierung & Steuerung Die Linie profitiert von Tetra Pak Ingenieurskunst mit integrierter Automatisierung zur Unterstützung eines stabilen aseptischen Betriebs. Zentrale Steuerungen koordinieren Füller-, Verschließer- und Verpackermodule für synchronisierten Durchsatz, präzises Timing und minimierte Stillstände. Rezepturgesteuerte Einstellungen ermöglichen konsistente Rüstprozesse für das Prisma 0,33L-Format, benutzerfreundliche HMI-Oberflächen erleichtern Überwachung, Diagnose und schnelle Anpassungen während der Produktion. Integrationsfähigkeit der Produktionslinie Konzipiert für nahtlose Integration in eine komplette Produktionsumgebung, unterstützt diese gebrauchte Abfülllinie sowohl Vor- als auch Nachgeschaltete Anbindungen wie Zuführung, Kartonbereitstellung und End-of-Line-Palettierung. Das Prisma 0,33L-Format ist Standard in der Konfiguration und gewährleistet zuverlässige Formatführung sowie effizienten Formatwechsel innerhalb der selben Formatfamilie. Die Förderertechnik und die Modulschnittstellen sorgen für kontinuierlichen Produktfluss und ausgewogene Linienleistung im industriellen Einsatzbereich von Gebrauchtanlagen. Maschinenzustand & Wartungshistorie Die gebrauchte Linie wird im funktionsfähigen Zustand und betriebsbereit angeboten, mit originaler Typenbezeichnung an den Anlagen. Das servicefreundliche Design von Tetra Pak ermöglicht routinemäßige Wartung, Verschleißteile und aseptisch relevante Komponenten sind gemäß Standard-Wartungsintervallen gut zugänglich für Inspektion und Austausch. Die Anlage ist geeignet für Betriebe, die ihre aseptische Getränkeproduktion erweitern oder standardisieren möchten – ohne große Inbetriebnahmeverzögerungen. Betriebsleistung & Vielseitigkeit Optimiert für aseptische Verarbeitung bietet das System kontrollierte Handhabung vom Füllen über das Verschließen bis zur Verpackung. Der TBA19 gewährleistet präzises Füllen unter aseptischen Bedingungen; der TCA45 appliziert passende Verschlüsse für Prisma-Kartons; und der TCBP70 übernimmt die Sekundärverpackung für effiziente Logistik. Das Resultat ist eine robuste Lösung für industrielle Verpackung, bei der Produktschutz, Haltbarkeit und einheitliche Präsentation entscheidend sind. Installationsvoraussetzungen & Standortanforderungen Die Linie ist zur Installation in einem hygienischen Produktionsbereich mit kontrollierten Umweltbedingungen für aseptischen Betrieb vorgesehen.

Sąlyga: labai geros būklės (naudotas), Eos Model: EOS M270 Metal Laser Sintering System Laser Sintering Machine 200 Watt Yb Fiber Laser Material processed with the system: Tungsten Laser hours: 8018 Usable build volume: 250 mm x 250 mm x 215 mm (including build platform) Layer thickness: 20 μm or 40 μm Precision optics: F-theta lens, high-speed scanner The system has been retrofitted with a Scanlab hurrySCAN 30 for more precise print results. Iijdpju Ebpcjfx Abkjk Focus diameter: 100 μm Dimensions (W x D x H) system: 2,000 mm x 1,050 mm x 1,940 mm Weight: approx. 1,130 kg For further technical information, please refer to the manufacturer. Scope of delivery: EOS M270, chiller, and software Condition: used (Specifications and data are subject to change. Errors excepted!) For further questions, we are happy to assist you by phone.

Sąlyga: naujas, Gamybos metai: 2025, OPTIturn TU 2004V - Lathe with Infinitely Variable Speed Control and Digital Speed Display Image shows OPTIturn TU 2004V Lathe with infinitely variable speed control and digital speed display Precision Manufacturing - Heavily ribbed prism bed made of cast steel, inductively hardened and precision-ground - Hardened and ground bed guideways - Hardened spindle nose (DIN 6350) Iedpfxjcnxrco Abkjik - Guaranteed spindle nose runout accuracy better than 0.009 mm - Automatic longitudinal/lead screw drive - With longitudinal, cross, and compound slides - Switchable right-left rotation from the control panel - Emergency stop impact switch - Chuck guard - Thrust bearing - Lead screw mounted in two sintered bearings - Wide thread cutting range via change gear set - Simple and fast speed changes via V-belt - Change gear drive - EMC filter class B (suitable for domestic use) Features: - Digital speed display - Easy-to-read digital speed display - Chip guard on compound slide - Four-way tool post, rotatable - Rolled trapezoidal leadscrew - Lead screw - Tailstock, offsettable for taper turning - Tailstock quill and handwheel with adjustable fine scale 0.02 mm - Main spindle, hardened and mounted in adjustable precision taper roller bearings - Taper roller bearings, P5 quality - Cylindrical centering fitting - Hardened spindle nose with 21 mm spindle bore - Chuck concentricity better than 0.04 mm Scope of Delivery: - 3-jaw chuck Ø 100 mm, self-centering - Fixed center MT 2 - Fixed center MT 3 - Splash guard - Chip tray - Four-way tool post - Change gear set - Operating tools Model: OPTIturn TU 2004V Article No.: 3420310 Technical Data - Electrical connection: 230 V / 1 Ph ~50 Hz - Main spindle motor power: 600 W - Spindle taper: MT 3 - Spindle bore: 21 mm - 3-jaw chuck pass-through: 20 mm - Tool post height max.: 12 mm - Center height: 100 mm - Distance between centers: 300 mm - Turning diameter max.: 200 mm - Swing over cross slide: 110 mm - Bed width: 100 mm - Spindle speed: 150 - 2,500 rpm - Number of speed ranges: 2, electronically adjustable - Compound slide travel: 55 mm - Cross slide travel: 75 mm - Longitudinal feed: 0.1 / 0.2 mm/rev - Metric thread pitch range: 0.25 - 3 mm/rev (14) - Imperial thread pitch range: 44 - 8 TPI (12) - Tailstock taper: MT 2 - Tailstock quill stroke: 65 mm - Dimensions (L x W x H): 830 x 425 x 360 mm - Net weight: 61 kg

Sąlyga: naujas, Gamybos metai: 2025, CORMAK HBS260 band saw for cutting pipes, profiles, and bars is widely used in all metalworking shops where precision, quality, and cutting speed are essential. The model features a swiveling arm adjustable from 0-60°. The design of the saw bow ensures accurate and quiet operation. It comes with a removable chip tray for easy cleaning! Machine Features This horizontal metal band saw with a swiveling arm allows for cutting perpendicular or at any angle between 0 and 60° to the material axis. The workpiece can be fed manually or with any mechanical device, while the saw blade feed operates automatically. The blade guides are fitted with special carbide inserts and bearings, which greatly improve blade tracking, longevity, straightness, and the quality of the cut. Carbide blade guides significantly reduce wear on both the machine and the blade. The machine is equipped with a high-performance coolant pump with a closed-cycle cooling system. The saw’s arm is cast from a single piece of cast iron, and, combined with a 27 mm wide band saw blade, it is fully suitable for serial cutting of both profiles and solid materials. The vice is mounted on an adjustable bed with a quick-release clamp. Blade guides are equipped with carbide inserts and rolling bearing systems. It is the CARBIDE BLADE GUIDES that ensure cutting precision and straightness. The upper part of the base is shaped to form a tray for collecting coolant and chips generated during the cutting process. To the base, a sturdy cast iron work table with a swiveling arm is mounted, along with a control panel on a separate arm. During cutting, the main cutting motion is performed by the moving saw blade, while arm feed is via gravity. The speed of arm descent (cutting speed) is adjusted using a hydraulic cylinder. Feed rate is controlled from the saw’s control panel. There are two blade speeds to choose from: 35 and 70 m/min. In the lower end position of the arm (after cutting the material), the drive to the blade is automatically switched off. Safety is ensured by saw blade guards and microswitches that stop the motor after the cutting cycle or when any guard is opened. Additional protection consists of the automatic saw shut-off in the event of blade breakage. Band saw blade size [mm]: 2520 x 27 x 0.9 Blade tension: mechanical (manual) Iodjudi Uzepfx Abkjik Blade speeds [m/min]: 35, 70 Arm descent adjustment: stepless – hydraulic cylinder Vice base height [mm]: 860 Saw wheel diameter [mm]: 300 Saw frame swivel [°]: 0-60 Power supply: 3-phase 400V Main motor power [kW]: 1.1/1.5 Coolant pump motor power [kW]: 0.05 Dimensions with base [cm]: 150x80x140 Weight [kg]: gross/net - 210 / 180 kg Additionally: - 2 pcs M42 saw blades - 5L Emulgol coolant - Magnetic chip collector ZW580

Sąlyga: beveik kaip naujas (parodų įrenginys), Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 525389e4-9874-4408-810c-82126df2811f, Gamybos metai: 2020, veikimo valandos: 7 508 h, bendras svoris: 75 kg, vidinis aukštis: 180 mm, vidinis ilgis: 300 mm, vidinis plotis: 220 mm, Įranga: CE žymėjimas, Hardly used showroom complete system consisting of the following components: Markforged Metal X 3D Printer Markforged Wash 1 Debinding Unit Markforged Sinter 2 Industrial Sintering Furnace & additional accessories Markforged Metal X TECHNICAL DETAILS Build volume: 300 x 220 x 180 mm Printing process: Atomic Diffusion Additive Manufacturing (ADAM) Print chamber: Heated Build plate: Heated, vacuum-sealed, with automatic leveling Print system: Dual-nozzle – Metal material and release material Print materials: Stainless steel 17-4 PH, 316L, Tool steel H13, A2, D2, Inconel 625, Copper, Titanium 6Al-4V Media supply: Filament feed, bound powder material Component characteristics Maximum component size: 250 x 183 x 150 mm Layer thickness: 50 microns and 125 microns MACHINE DETAILS Dimensions & weight Dimensions: 575 x 467 x 1,120 mm Iisdpfx Abex I Rfgjkek Weight: 75 kg Software: Eiger Cloud Printer power supply: 100–240 V / 50–60 Hz / 12.6 A Certificates: CE, FCC, UL, RCM, UKCA Safety features: Two-factor authentication, organizational admin access, single sign-on EQUIPMENT Argon gas control with pressure regulators and quick couplings Original Markforged transport case with spare build plates Caster wheels Isolation transformer

Sąlyga: naudotas, rida: 251 500 km, galia: 120 kW (163,15 AG), pirmoji registracija: 06/2015, kuro tipas: dyzelinas, bendras svoris: 3 500 kg, kita apžiūra (TÜV): 03/2023, spalva: ruda, pavaros tipas: automatinis, emisijos klasė: Euro 6, sėdimų vietų skaičius: 3, krovimo vietos ilgis: 4 320 mm, krovinių skyriaus plotis: 2 130 mm, krovos erdvės aukštis: 2 070 mm, Gamybos metai: 2014, Įranga: ABS, centrinis užraktas, elektroninė stabilumo programa (ESP), oro kondicionavimas, suodžių filtras,

Sąlyga: beveik kaip naujas (naudotas), Funkcionalumas: visiškai funkcionalus, Gamybos metai: 2022, bendras ilgis: 1 480 mm, bendras aukštis: 2 040 mm, bendras plotis: 850 mm, bendras svoris: 360 kg, įėjimo įtampa: 220 V, įėjimo srovė: 32 A, As-new XYZPrinting MfgPro230xS 3D printer from 2022. The machine has barely been used and is in excellent condition – ideal for anyone seeking a reliable, high-performance 3D printer. Why choose the XYZPrinting MfgPro230xS? Iiedpfx Abet H I Tvjksk Outstanding print quality: With its precise print technology and a resolution of up to 50 microns, the MfgPro230xS delivers impressive results that meet the highest industrial standards. High printing speed: Save valuable production time. The MfgPro230xS offers rapid print speeds without compromising quality. Large build volume: With a generous build space of 230 x 230 x 230 mm, even larger projects are easily accommodated. User-friendly: Simple operation and an intuitive interface make this 3D printer easily accessible, even for beginners. Reliability: Thanks to its robust construction and high-quality components, the MfgPro230xS is extremely durable and dependable. With the XYZprinting MfgPro230xS industrial 3D printing system, you can manufacture the most complex structures in a single piece and without support structures using selective laser sintering in your own workshop. Designed for professional applications as well as for use in institutes and universities. Accessories: - Sinterit FZ138 PHS Station - Sinterit FZ101 ATEX Vacuum Cleaner 230V - Sinterit Sandblaster SLS - N2 Generator

Sąlyga: labai geros būklės (naudotas), EOS Metal Laser Sintering System We are offering an EOS metal laser sintering system for sale. Material processed with the system: Gold Laser type: Yb-fiber laser, 100 W Scanning speed: up to 7.0 m/s Build volume: Ø80mm x 100mm System dimensions (W x D x H): 800 mm x 950 mm x 1,850 mm Installation area: 1000 mm x 3000 mm x 2500 mm Weight: approx. 580 kg Software: EOS RP Tools, Offline PSW CAD interface: STL Network: Ethernet Type: EOS M080 External gas connection (nitrogen) Iiodpfxjqzgvho Abkek Maximum power consumption: 2.3 kW, 13A Scope of delivery: as shown in the pictures Condition: used (Specifications are subject to change and error!) For further questions, we are happy to assist you by phone.

Gamybos metai: 1995, Sąlyga: paruoštas naudoti (naudotas), Product: Electric Sintering Furnace Year of manufacture: 1995 Isdjg R Sh Ajpfx Abkjik Air transport: 2 x 9000 m³/h Chamber capacity: 32 m³ Furnace opening: 1200 x 1200 mm // 80 x 1500 mm Heating capacity: 55-160 kW, G20 natural gas Air temperature: 170-220 °C Casing size: 2600 x 10300 x 3600 mm Control cabinets included. Requires electrical and mechanical refurbishment.

Sąlyga: naujas, Gamybos metai: 2025, Universal Lathe CORMAK 310 x 900 (TU3109V), VARIO version with stepless spindle speed adjustment. Machining capacity: 310 x 900 mm. Equipped with a modern 1.5 kW / 230 V DC motor, cooling system, and digital readout. Recommended for turning hard steels, internal and external surfaces, tapers, polishing, metric and imperial threading, drilling, and broaching. Semi-professional model, suitable for single-piece and small-batch production. Machine supplied with base. The CORMAK 310 x 900 (TU3109V) 230V universal lathe features smooth spindle speed regulation, ensuring ergonomic operation tailored to user needs. Shorter setup times when machining a wide range of workpiece sizes translate into improved efficiency and ease of use. VARIO Version – electronic, infinitely variable spindle speed control via DC motor and voltage regulator, providing optimal spindle chuck rotational accuracy for superior machining quality. The modern DC motor with stepless spindle speed control offers ease of use and reduced setup times. Smooth and efficient drive with excellent rotational speed and torque characteristics. LCD display shows spindle speed, enabling direct monitoring and quick speed adjustments during selection of cutting and threading modes. Two spindle speed ranges: low (80–1000 rpm) for machining hard steels and high (160–2000 rpm) for high-speed precision turning. Easy regulation of spindle speed and automatic feed via ergonomic gearbox control panel. Bed with induction-hardened and ground guideways. 180 mm bed width ensures stable and precise working conditions. Wide threading range (right and left threads): metric – (18) 0.2–3.5 mm, imperial – (18) 8–48 TPI. Automatic longitudinal feed: 0.085–1.832 (9) mm/rev., and cross feed: 0.010–0.100 (9) mm/rev., to reduce machining time and improve quality when turning long workpieces. 38 mm spindle bore allows optimal machining performance on large-diameter shafts. Compound slide with graduated scale, swivels ±45°, tailstock set-off ±10 mm for taper turning. Hardened and ground spindle gearbox gears. Leadscrew and feed shaft for threading, as well as automatic longitudinal and cross feed. Iodpsric Idefx Abkjik Cooling system and 2-axis digital readout included as standard. Machine fully compliant with EU (CE), Polish regulations, and DIN standards.

Sąlyga: beveik kaip naujas (parodų įrenginys), Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 525389e4-9874-4408-810c-82126df2811f, Gamybos metai: 2020, veikimo valandos: 7 508 h, bendras svoris: 75 kg, vidinis aukštis: 180 mm, vidinis ilgis: 300 mm, vidinis plotis: 220 mm, Įranga: CE žymėjimas, Hardly used showroom complete system consisting of the following components: Markforged Metal X 3D Printer Markforged Wash 1 Debinding Unit Markforged Sinter 2 Industrial Sintering Furnace & additional accessories Iiedjx I Rfaopfx Abkjk Markforged Metal X TECHNICAL DETAILS Build volume: 300 x 220 x 180 mm Printing process: Atomic Diffusion Additive Manufacturing (ADAM) Print chamber: Heated Build plate: Heated, vacuum-sealed, with automatic leveling Print system: Dual-nozzle – Metal material and release material Print materials: Stainless steel 17-4 PH, 316L, Tool steel H13, A2, D2, Inconel 625, Copper, Titanium 6Al-4V Media supply: Filament feed, bound powder material Component characteristics Maximum component size: 250 x 183 x 150 mm Layer thickness: 50 microns and 125 microns MACHINE DETAILS Dimensions & weight Dimensions: 575 x 467 x 1,120 mm Weight: 75 kg Software: Eiger Cloud Printer power supply: 100–240 V / 50–60 Hz / 12.6 A Certificates: CE, FCC, UL, RCM, UKCA Safety features: Two-factor authentication, organizational admin access, single sign-on EQUIPMENT Argon gas control with pressure regulators and quick couplings Original Markforged transport case with spare build plates Caster wheels Isolation transformer

Sąlyga: beveik kaip naujas (naudotas), Funkcionalumas: visiškai funkcionalus, Gamybos metai: 2014, bendras ilgis: 1 100 mm, bendras aukštis: 1 510 mm, bendras plotis: 850 mm, bendras svoris: 160 kg, We offer a powder unpacking and sieving station as well as an unused drum mixing station from EOS GmbH. This mixing station is ideally designed for use with wide-mouth drums. It enables the efficient mixing of sieved recycled powder with new powder over a preset period. The processed powder can then be used in EOS Formiga P100 or P110 systems. The unpacking and processing station consists of: • an unpacking area • a sieving unit for used powder • a feed for new powder • and a scale for processing plastic powder. After removal from the machine, the cooled exchange frame is placed into the unpacking and processing station. By incrementally raising the build platform using a foot pedal, the powder bed with components is pushed out from the exchange frame. The sintered parts are manually unpacked from the powder bed. Reusable used powder from the powder bed is pushed onto the adjacent perforated plate and falls through a hose into a sieve bowl. The used powder is sifted into a powder container which is placed on a scale beneath the sieving unit. The scale enables precise determination of the sieved amount of recycled powder. Subsequently, a previously determined amount of new powder is added to the recycling powder in the powder container by turning a hand crank. The processed plastic powder then needs to be mixed in the mixing station and can subsequently be returned to the build process. Mixing station Iisdpfx Asxzpw Sobksk We offer an unused drum mixing station from EOS GmbH. At the mixing station, new powder and recycled powder—previously filled into powder containers at the unpacking and processing station—are mixed. A powder container is rolled or placed onto the mixing station, which then rotates continuously for a preset time. After the preset period ends, the mixing station stops and the powder container can be removed.

Sąlyga: paruoštas naudoti (naudotas), Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: SP0119240003037, Gamybos metai: 2019, įėjimo įtampa: 240 V, Įranga: CE žymėjimas, Metalo 3D spausdinimo sistema Bound Metal Deposition™ susideda iš: - spausdintuvo - debinderio - sinterizacijos krosnies - dažnio keitiklio krosnies maitinimui 60Hz dažniu. Sistema puikios būklės, naudota MTEP tikslais kondicionuojamoje patalpoje. Spausdintuvas komplektuojamas su 2 purkštukais, kurių skersmuo 0,40mm, ir vienu aukštos raiškos purkštuku 0,25mm. Krosnis su techninių dujų tiekimo sistema iš išorinės instaliacijos. Komplekte originalūs krosnies atsarginiai dalių rinkiniai (keramikinis setteris, grafitiniai retortos padėklai, tarpinės, filtrai, vakuuminio siurblio alyva). Iodpfx Absxlcldekoik Visa sistema su atnaujinta programine įranga (naujausia versija). Į komplektą įeina kasetės su medžiagomis: 1x AISI 316L 1x 17-4PH 1x keramikinė atrama

Sąlyga: labai geros būklės (naudotas), EOS Metal Laser Sintering System We are offering an EOS metal laser sintering system for sale. Material processed with the system: Gold Laser type: Yb-fiber laser, 100 W Scanning speed: up to 7.0 m/s Build volume: Ø80mm x 100mm System dimensions (W x D x H): 800 mm x 950 mm x 1,850 mm Installation area: 1000 mm x 3000 mm x 2500 mm Weight: approx. 580 kg Software: EOS RP Tools, Offline PSW CAD interface: STL Network: Ethernet Type: EOS M080 External gas connection (nitrogen) Iodpfx Abeqy Edysksik Maximum power consumption: 2.3 kW, 13A Scope of delivery: as shown in the pictures Condition: used (Specifications are subject to change and error!) For further questions, we are happy to assist you by phone.

Sąlyga: beveik kaip naujas (parodų įrenginys), Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 525389e4-9874-4408-810c-82126df2811f, Gamybos metai: 2020, veikimo valandos: 7 508 h, bendras svoris: 75 kg, vidinis aukštis: 180 mm, vidinis ilgis: 300 mm, vidinis plotis: 220 mm, Įranga: CE žymėjimas, Hardly used showroom complete system consisting of the following components: Markforged Metal X 3D Printer Markforged Wash 1 Debinding Unit Markforged Sinter 2 Industrial Sintering Furnace & additional accessories Markforged Metal X TECHNICAL DETAILS Build volume: 300 x 220 x 180 mm Printing process: Atomic Diffusion Additive Manufacturing (ADAM) Print chamber: Heated Build plate: Heated, vacuum-sealed, with automatic leveling Print system: Dual-nozzle – Metal material and release material Print materials: Stainless steel 17-4 PH, 316L, Tool steel H13, A2, D2, Inconel 625, Copper, Titanium 6Al-4V Media supply: Filament feed, bound powder material Component characteristics Maximum component size: 250 x 183 x 150 mm Layer thickness: 50 microns and 125 microns Iodpfx Asxu Ewzsbkjik MACHINE DETAILS Dimensions & weight Dimensions: 575 x 467 x 1,120 mm Weight: 75 kg Software: Eiger Cloud Printer power supply: 100–240 V / 50–60 Hz / 12.6 A Certificates: CE, FCC, UL, RCM, UKCA Safety features: Two-factor authentication, organizational admin access, single sign-on EQUIPMENT Argon gas control with pressure regulators and quick couplings Original Markforged transport case with spare build plates Caster wheels Isolation transformer

Sąlyga: labai geros būklės (naudotas), Desktop Metal 3D Printer Complete System We offer you a Desktop Metal 3D printer complete system. 3D Metal Printer Studio System from Desktop Metal Complete System: 3D Printer + Debinding Machine + Sintering Furnace Ijdpfx Ajk Hz Nqebkeik Manufacturer: Desktop Metal Model: Desktop Metal Studio System Operating Condition: Used (Good) Year of Manufacture: 2019 Desktop Metal Studio System includes: 1.1 Desktop Metal Studio 3D Printer Bound Metal Deposition (BMD) Technology Specifications: - Printable Materials: Metal - Technology: FDM - Application: Industrial - Other Features: Suitable for office use - X-Axis Travel: 30 cm (12 in) - Y-Axis Travel: 20 cm (8 in) - Z-Axis Travel: 20 cm (8 in) Description: Unlike laser-based systems that selectively melt metal powder, this printer extrudes bound metal rods—similar to an FDM printer. This eliminates the safety requirements often associated with metal 3D printing and enables new features such as the use of closed-cell infills for lightweight yet strong parts. 1.2 Desktop Metal Studio Debinder (Delamination Machine) - Fully automatic debinding - Cleaning tank: 17.4 L (in process) / 22.5 L (storage) Description: The Debinder prepares green parts for sintering by dissolving the primary binder. With a low-emission design, it requires no external ventilation and is safe for office environments. Automatic liquid distillation and recycling means no refilling is required between cycles. 1.3 Desktop Metal Studio Sintering Furnace - Hybrid technology (microwave & conventional heating elements) - Build Volume: 305 x 205 x 205 mm - Carbon casing - Gas supply: 2 x 900 L gas bottles - Heating power: 20 kW Specifications: - Function: Sintering - Configuration: Chamber - Heat source: Gas - Other Features: High-temperature, automatic operation - Maximum temperature: 1,400°C (2,552°F) Description: Fully automated and designed to fit through an office door, the furnace provides industrial-grade sintering in an office-friendly package. Built-in, material-specific temperature profiles ensure uniform heating and cooling without the residual stresses often found in laser-based systems. Condition: Used Scope of delivery: (See images) (Subject to technical changes and errors; all information is non-binding!) For further questions, we are happy to assist you by phone.

Sąlyga: labai geros būklės (naudotas), EOS Metal Laser Sintering System We are offering an EOS metal laser sintering system for sale. Material processed with the system: Gold Laser type: Yb-fiber laser, 100 W Scanning speed: up to 7.0 m/s Build volume: Ø80mm x 100mm System dimensions (W x D x H): 800 mm x 950 mm x 1,850 mm Installation area: 1000 mm x 3000 mm x 2500 mm Weight: approx. 580 kg Software: EOS RP Tools, Offline PSW CAD interface: STL Network: Ethernet Type: EOS M080 Isdpfxsqzgvas Abksik External gas connection (nitrogen) Maximum power consumption: 2.3 kW, 13A Scope of delivery: as shown in the pictures Condition: used (Specifications are subject to change and error!) For further questions, we are happy to assist you by phone.