Daug Rankinis Pjūklas pirkti naudotą (9 564)

Sąlyga: naujas, Gamybos metai: 2025, CORMAK HBS275 Band Saw for cutting pipes, profiles, and rods is widely used in all locksmith workshops where precision, quality, and cutting speed are paramount. The model is equipped with a swiveling arm adjustable from 0-60°, with saw guides based on carbide inserts. The robust frame design ensures precise and quiet operation. Machine Features The horizontal metal band saw with a swiveling arm allows cutting perpendicular to the axis of the material as well as at any angle between 0 and 60°. The material can be fed manually or with any mechanical device, while the tool feed is fully automatic. The blade guides are fitted with special carbide plates and bearings, significantly enhancing blade guidance, lifespan, straightness, and the quality of the cut. Carbide guidance greatly reduces both machine and blade wear. The machine is equipped with a high-efficiency coolant pump in a closed-loop system. The saw arm, made of a single cast-iron piece, combined with a 27 mm wide saw blade, allows for repeated series cutting of both profiles and solid materials. The vise is mounted on an adjustable bed and features quick clamping. Blade guides fitted with hard metal (carbide) plates and a rolling bearing system ensure cutting precision and straightness—carbide-guided blade supports are crucial for quality results. The arm is equipped with an automatic blade tension sensor and is tilted at 25 degrees to prolong blade life. A cleaning brush, mounted underneath the arm, ensures blade cleanliness and effective operation. Power is transmitted through a worm gear drive. A cast-iron work table with a swiveling arm and a separate control panel is attached to the base. During cutting, the main movement is the saw blade’s feed, and the arm’s descent serves as the feed direction. The descent (cutting) speed is regulated by a hydraulic cylinder. Feed speed is controlled from the saw’s control panel. The operator can select one of two blade speeds: 37.5 or 75 m/min. In the lower arm position (after finishing the cut), the blade drive shuts off automatically. Safety is ensured by blade guards and micro-switches stopping the motor once the cutting cycle ends or if any guard is opened. Additional protection cuts off the machine automatically if the blade breaks. The drive is transmitted via a worm gear motor. The motor has a thermal fuse, protecting it from overheating during operation. Technical Data TOTAL POWER: 1.5 kW POWER SUPPLY: 400V 50Hz ARM DESCENT CONTROL: hydraulic cylinder BLADE DIMENSIONS: 2450 x 27 x 0.9 mm BLADE SPEED: 37.5 / 75 m/min VISE BASE HEIGHT: 900 mm MACHINE DIMENSIONS (WITH RAISED ARM) (L x W x H): 1720 x 800 x 1800 mm WEIGHT: 215 kg CUTTING CAPACITY Angle | Round | Flat | Square ---|---|---|--- 0° | ø220 | 260 x 140 | 200 x 200 45° R | ø160 | 160 x 140 | 160 x 160 60° R | ø100 | 120 x 100 | 100 x 100 Ffodpfxoudi Une Ab Sst Price does not apply to machines purchased in Poland.

Sąlyga: naujas, Gamybos metai: 2025, Profesjonalna, bardzo wydajna i mocna piła taśmowa do metalu z ramieniem odchylanym o 45°. Doskonałe rozwiązanie dla zakładów ślusarskich, produkcyjnych oraz warsztatów rzemieślniczych. Od lat niezrównana, a dzięki przemyślanej konstrukcji i solidnemu wykonaniu stanowi idealne rozwiązanie. Opis maszyny Profesjonalna, bardzo wydajna i efektywna piła taśmowa do metalu z ramieniem odchylanym o 45°, model CORMAK BS 712 SW, oparta jest na dopracowanych rozwiązaniach, co czyni ją bezkonkurencyjną w swojej klasie. Ramię wykonane z profilowanego żeliwa sferoidalnego zapewnia sztywność podczas pracy i tłumi wszelkie drgania. Panel sterowania umieszczony jest na ramieniu przecinarki. Urządzenie cechuje wysoka wydajność i łatwość obsługi. Umożliwia cięcie w płaszczyźnie pionowej oraz w płaszczyźnie prostopadłej do osi ciętego materiału, a także pod dowolnym kątem w zakresie 45° – 90°. Element cięty może być podawany ręcznie lub za pomocą urządzenia podającego. Posuw podczas cięcia jest grawitacyjny, oparty na zasadzie przepływu oleju w dwukomorowym siłowniku hydraulicznym. Odpowiednią prędkość opuszczania ramienia uzyskuje się dzięki zaworowi regulującemu przepływ oleju pomiędzy komorami siłownika hydraulicznego. Wytrzymała, stabilna i dopracowana konstrukcja, a także ramię wykonane z jednolitego żeliwa gwarantują sztywność i stabilność podczas cięcia, zapewniając precyzję oraz długotrwałą niezawodność. Zastosowanie taśmy o szerokości 20 mm pozwala na przecinanie dużych ilości elementów. Wymaganą prędkość liniową taśmy uzyskuje się przez zmianę przełożenia na kole pasowym pomiędzy przekładnią ślimakową a silnikiem napędowym. Dane techniczne Moc silnika: 1,1 kW Ffedpfxow U Skvs Ab Sjt Prędkości taśmy: 22/33/45/65 m/min Zasilanie: 400 V Wymiary taśmy: 2360×20×0,9 mm Zakres cięcia: 45°L – 45°P Waga: 145 kg Wymiary: 1280x575x1140 mm Kąt cięcia 0°.....Ø 205.....215×205.....205×205 45° L.....Ø 150.....100×200.....130×130 45° P.....Ø 140.....140×90.....90×90 Podana cena jest ceną netto. Cena nie obejmuje kosztów transportu. Więcej informacji udzielimy telefonicznie lub mailowo. Zapraszamy do zapoznania się z ofertą na naszej stronie internetowej.

Sąlyga: naujas, Gamybos metai: 2025, CORMAK BS530H Bandsaw for Metal – Professional Tool for Cutting Pipes and Profiles The CORMAK BS530H metal bandsaw is a high-performance semi-automatic machine designed for precise cutting of steel components, pipes, and profiles at various angles. Its robust cast iron construction, reinforced blade guiding system, and advanced hydraulics make it ideal for serial production and demanding industrial environments. The integrated control panel allows single-operator management of all machine functions, significantly reducing operation time and improving work ergonomics. Ffodpfjw U Svlsx Ab Sot Key Features Semi-automatic mode – hydraulic lifting and lowering of the saw arm and vice operation via the control panel. Worm gear drive with bronze elements ensures smooth, precise operation without vibrations. Stepless cutting speed adjustment from 20–70 m/min for various materials. Carbide and roller bearing blade guides for durability and precise blade tracking. Quick-action vice, manually or hydraulically actuated, with adjustable left/right positioning. Miter cutting from -45° to +60° with accurate scale display. Heavy-duty cast iron body ensures cutting stability and long machine lifespan. Hydraulic downfeed control with adjustable return height. Design and Technology Model BS530H stands out with its reinforced drive gearbox and industrial-grade hydraulics, ensuring reliability under intensive use. The massive frame construction minimizes vibrations and guarantees even operation. The ergonomic console allows full process control from a single station. The coolant system, integrated into the base, efficiently dissipates heat and removes debris, protecting the saw blade from overheating. Precision and Work Efficiency Thanks to stepless speed control, selectable manual or semi-automatic operation, and an analog tensiometer for monitoring blade tension, the BS530H metal bandsaw delivers consistent, high-quality cuts even in long production runs. Efficiency is further boosted by a material supporting roller and an arm lock ensuring safety at the end of the cycle. Application The machine is dedicated to industrial manufacturing plants, metal workshops, and firms performing serial cutting of profiles, pipes, and solid steel sections. It is ideal for mass production, prefabrication, and preparing parts for welding or further processing. Standard Equipment Semi-automatic control console Hydraulic vice Blade cleaning brush Liquid cooling system with pump Front material feed roller Analog blade tension gauge CE certification and operating manual Technical Specifications Working height: 965 mm Cutting speed: 20 – 70 m/min Saw blade dimensions: 3770 x 34 x 1.1 mm Coolant system power: 0.1 kW Total power: 3.0 kW Supply voltage: 400 V Dimensions (W x D x H): 2200 x 1400 x 2050 mm Weight: 730 kg

Sąlyga: naujas, Gamybos metai: 2025, Table saw with table, right-side table extension, and both straight and mitre fences. This machine incorporates numerous features typically found in higher-priced equipment of this kind. The excellent price-to-performance ratio is achieved without compromising on quality or versatility. Machine description The innovative table saw is a combination of a powerful, precise, versatile, and compact unit. It is designed for small woodworking shops, furniture manufacturers, and craftsmen. Many solutions used in more expensive machines of this type have been implemented in this model. The excellent price-to-performance ratio is achieved without any compromise in quality or versatility. Supplied with 250 x 30 x 2 mm carbide-tipped circular saw blade MAX. BLADE/ARBOR DIAMETER: 254 x 30 mm BLADE SPEED: 4000 rpm BLADE TILT RANGE: 90 – 45° MAX. CUTTING DEPTH AT 45º: 65 mm Ffjdpfx Asvxhkieb Sot MAX. CUTTING DEPTH AT 90º: 80 mm CUTTING WIDTH WITH TABLE EXTENSION: 750 mm MAX. CUTTING LENGTH: 1000 mm EXTRACTION PORT: 100 / 25 mm WORKTABLE DIMENSIONS: 635 x 420 mm WORKTABLE DIMENSIONS WITH EXTENSION: 635 x 1500 mm MOTOR POWER: 2.2 kW (S1) 230V / 3.1 kW (S6) WEIGHT: 110 kg DIMENSIONS: 1450 x 1000 x 1100 mm Manufacturer: Cormak

Sąlyga: naujas, Gamybos metai: 2025, The TS315 table saw has been designed for small woodworking shops, furniture manufacturers, and craftsmen. This machine incorporates many features typically found in much more expensive equipment of this type. The innovative circular saw offers a combination of power, precision, versatility, and a compact design. An excellent price-to-performance ratio has been achieved without any compromise in quality or flexibility. Machine Description The TS 315 industrial circular saw for solid wood is an innovative combination of a powerful, precise, universal, and compact machine! It is tailored for woodworking shops, hobbyists, furniture makers, and artisans. This machine adopts many solutions usually seen in much more expensive equipment of this kind! An outstanding ratio of price to performance has been achieved without sacrificing quality or versatility! The machine is also suitable for processing high-density boards, MDF, ABS panels, PVC, solid wood, and other wood-based or similarly structured and hard materials. Infinitely variable and precise height and angle adjustment via handwheel Stable, heavy-duty, high-quality machine body Table extensions and outfeed provide comfortable operation Smooth-running, reinforced aluminium sliding table Precision parallel fence with fine adjustment Solid telescopic arm and extendable crosscut table Powerful main drive motor ensures consistent cutting speed, even at a cutting height of 100 mm Technical Specifications Blade size: 315x30x3.2 mm Blade speed: 4250 rpm Ffjdpfx Abevxhm Do Sst Max. cutting height at 90/45 degrees: 100/75 mm Max. cutting width on the fence: 940 mm Working table size: 800 x 365 mm Table extension: 760 x 600 mm Table widening: 500 x 350 mm Sliding table: 1600 x 238 mm Dust extraction port diameter: 100 mm Motor power S1/S6: 2.8 kW / 3.3 kW Supply voltage: 400V Weight: 245 kg Machine dimensions: 1540 x 2400 x 1300 mm

Sąlyga: naujas, Gamybos metai: 2025, The PS12E-2000 panel saw is a professional woodworking tool distinguished by its versatility and advanced features. This circular saw is designed for a wide range of wood processing tasks, offering both precise cuts of narrow and thin boards and the capability to handle thick wooden worktops with a maximum thickness of up to 100 mm. Fjdpfx Abovuf Tmj Sjft Main features of the PS12E-2000 sliding table panel saw: - Dual saw blades: The machine is equipped with two saw blades – a main and a scoring blade, allowing for versatile cutting of various types of wood materials. - Scoring unit for MDF panels: An additional scorer is integrated into the machine, enabling precise cutting of MDF boards and other wooden materials of similar structure. - Blade height adjustment: Offers smooth adjustment of the saw blade height up to 100 mm, allowing adaptation to different material thicknesses. - Blade tilt: The saw blade can be tilted from 90° to 45°. - Heavy-duty guides: The machine features robust steel longitudinal and angular guides, both fitted with measurement scales. - Additional sliding table: A large bearing-mounted sliding table with support is one of the main advantages of this saw, enabling processing of large-format panels and materials with a significant surface area. - Sawdust extraction system: The woodworking machine is fitted with a pipe system for sawdust removal, helping to keep the workspace clean. - Easy blade change: The blade replacement process is quick and efficient, enabling productive operation. - Rip fence with scale: The machine features a rip fence with a precise scale, facilitating series cuts of identical lengths. - Saw blade guard: The saw comes with a blade guard that can also be connected to an extraction system, ensuring safety and cleanliness at the workspace. Technical data: - Sliding table length [mm]: 2000 - Cutting width, right side [mm]: 1260 - Blade tilt [°]: 45 - Cutting height at 45° [mm]: 80 - Cutting height with 315 mm blade at 90° [mm]: 100 - Cutting height with 300 mm blade at 90° [mm]: 95 - Maximum saw blade size [mm]: 315 x 30 - Maximum scoring blade size [mm]: 100 x 20 - Main saw blade speed [rpm]: 4500 - Scoring blade speed [rpm]: 5800 - Motor power S1/S6: 3.8 kW / 6.1 HP - Power supply: 3-phase, 400V - Weight [kg]: 275 - Warranty [months]: 12

Sąlyga: naujas, Gamybos metai: 2025, CORMAK HBS320 for double-sided mitre cutting in the range from -45° to +60°. The design of the machine is based on solutions and projects by Polish engineers. Its precision and manufacturing accuracy place it at the forefront of band saws offering cutting widths up to 320 mm. A major advantage of this machine is the latest generation hydraulic cylinder. The machine features a reinforced vise base and quick-release vise function. Machine features The CORMAK HBS320 metal band saw allows for cutting material at any angle between -45° and +60°. The material to be cut can be fed manually or using any external feeder. The cut feed is gravity-assisted, controlled by hydraulic oil flow within the cylinder. The operator starts the machine with a start button and sets the desired cutting speed. After the cutting cycle completes, the machine stops automatically and the operator raises the arm to the starting position. The saw arm is made from a heavy-duty, one-piece grey cast iron casting. Together with a 27 mm wide blade, it is perfectly suited for series cutting of structural, stainless, and tool steels. The vise is set in an adjustable bed and equipped with a quick-release clamp. The blade guides are fitted with ball bearings and carbide inserts, ensuring excellent cutting precision and straightness. This greatly affects blade guidance, durability, accuracy, and cut quality. Carbide guidance significantly reduces machine and blade wear. The base is a rigid, steel-welded frame. Inside is a separate coolant reservoir with an electric pump. The top of the base is tray-shaped, channeling coolant and collecting chips generated during cutting. Also attached to the base is a robust cast iron worktable with a swiveling arm and control panel. Feed speed can be regulated from the control panel. Two blade speeds are available: 44 and 88 m/min. In the lowest arm position—after the cut—the blade drive is switched off automatically. Safety is ensured by blade covers and micro-switches that stop the motor when the cutting cycle is complete or any guard is opened. Additional protection involves automatic shutdown if the blade breaks. Technical data Ø MAX - 260 mm / straight cutting H x W MAX - 320 x 160 mm / straight cutting POWER SUPPLY - 3-phase 400V TOTAL POWER - 1.5 kW ARM DESCENT CONTROL - hydraulic cylinder BLADE SIZE - 2740 x 27 x 0.9 mm BLADE SPEED - 44 / 88 m/min VISE BASE HEIGHT - 920 mm DIMENSIONS - 1400 x 880 x 1550 mm WEIGHT - 280 kg Cutting parameters Angle 0º -----ø260 320 x 160 255 x 255 45º R ø210 210 x 200 210 x 210 Ffodpoi D Dgwofx Ab Set 60º R ø135 135 x 130 130 x 130 45º L ø160 220 x 130 160 x 160 All prices are NET and do not include transport costs. For more information, please contact us by phone or email. We also invite you to browse our full offer on our website.

Sąlyga: naujas, Gamybos metai: 2025, The table saw is exceptionally easy to operate and user-friendly. This machine incorporates many solutions typically found in more expensive devices of this type. Table saw with table, right-hand table extension, and angle fence. Machine Description This innovative circular saw combines a powerful, precise, universal, and compact design. It has been created with small joinery workshops, furniture manufacturers, and craftsmen in mind. This machine features many solutions usually reserved for higher-end machines in its category. An excellent price-to-performance ratio has been achieved without compromising on quality or versatility. Supplied with a 250 x 30 x 2 mm carbide-tipped saw blade Technical Specifications MAXIMUM BLADE DIAMETER/BORE: 254 mm SPEED: 4000 rpm BLADE TILT RANGE: 90 – 45° MAXIMUM CUTTING DEPTH AT 45°: 56 mm MAXIMUM CUTTING DEPTH AT 90°: 80 mm SLIDING TABLE TRAVEL: 620 mm MAXIMUM CUTTING WIDTH TO THE RIGHT OF THE BLADE: 610 mm TABLE HEIGHT: 890 mm MOTOR POWER: 2.2 kW (S1) / 3.1 kW (S6) Ffedsvxhhzepfx Ab Set POWER SUPPLY: 230 V WEIGHT: 125 kg DIMENSIONS: 1090 x 1330 x 910 mm

Sąlyga: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, The Cormak MJ45-KB4 panel saw with scoring unit is an advanced woodworking machine, commonly referred to as a panel saw with scorer. This is an ideal solution for cutting and processing various types of materials, primarily wood, chipboard, MDF boards, and other wood-based materials. Construction and Design: The Cormak MJ45-KB4 is a robust woodworking machine featuring a durable steel frame, ensuring stability during operation. The large work table, guided on hardened steel rods and offering a carriage length of 3200 mm, with integrated cutting units, guarantees both efficiency and accuracy. Main Cutting Unit: Scoring Unit: A key feature of this saw is the scoring blade, which relieves internal stresses in the wood by scoring the underside of the workpiece. This reduces the risk of cracking and deformation after cutting. The 0.75 kW scoring motor ensures reliable scoring operations. Main Saw Blade: The Cormak MJ45-KB4 is equipped with a circular saw blade as the main cutting tool. The electric motor drives the saw blade, enabling precision cutting. With a blade diameter of 350 mm, the maximum cutting height is up to 105 mm. Manual Scoring Adjustment: Easy and effective manual scoring adjustment allows for quick and precise tool settings. Adjustable stops make it easy to return to previous settings, and the intuitive control location at the operator’s workstation allows adjustments without work interruption. Features and Advantages of the Panel Saw: - Large working area: The panel saw has a spacious working surface, facilitating handling of large material sheets. - Smooth feed: The feed system utilizes precision-hardened steel guides and ball bearings, which ease longitudinal cutting of long panels or plywood sheets. - Angle and cutting depth adjustment: Adjustable angle and cutting depth enable the tool to be tailored to specific project requirements. - Safety features: The panel saw is equipped with safety devices, including blade guards and emergency stop systems to ensure safe operation. Applications of Panel Saws with Scoring Unit: Panel saws with a scoring unit are mainly used in the woodworking and window manufacturing industries for cutting wood and wood-based materials. They are ideal for cutting boards, chipboard, MDF panels, and similar materials. The Cormak MJ45-KB4 is a professional tool distinguished by high precision. Technical Specifications Table dimensions: 990 x 575 mm Sliding table length: 3200 mm Cutting width with rip fence: 1250 mm Crosscut with crosscut fence: 3100 mm Blade tilt: 0° - 45° Saw blade diameter: Ø350 mm Main blade bore: Ø30 mm Ffedpjtz Smiefx Ab Sjt Blade height: 0-105 mm Blade height at 45°: 0-73 mm Main saw spindle speed: 4000 / 6000 rpm Scoring blade diameter: Ø125 mm Scoring blade bore: Ø20 mm Scoring spindle speed: 8000 rpm Main motor power S1/S6: 5.5 kW / 9 HP Scoring motor power S1/S6: 0.75 kW / 1.2 HP Dust extraction port under table: 100 mm Dust extraction port at blade guard: 80 mm Machine weight: 680 kg Saw delivered without saw blades. Price not valid for machines sold in Poland.

Sąlyga: naujas, Gamybos metai: 2025, Ideal machine for processing high-density boards, MDF, ABS panels, PVC, solid wood, and other wood-based materials or those with similar structure and hardness. The machine is built on a welded steel body with a fixed cast iron table and a moving table made of high-strength profiled aluminum. This machine is perfect for both professionals and hobbyist woodworkers. Cormak Panel Saw with Scoring Unit The MJ45KB3-2000 panel saw with a separate motorized scoring unit is an excellent tool for precise wood processing. This innovative machine offers many advanced solutions that ensure outstanding cut quality. Key features of the Cormak panel saw with scoring unit: - 2000 mm aluminum sliding table enables smooth movement across the material, ensuring precise cuts up to nearly 2000 mm in length - 1600 mm telescopic arm with a scale and two stops for precise and stable guidance of the workpiece - Solidly mounted saw unit in a cast iron body, guaranteeing the machine's durability and reliability - Accurate movements thanks to a hardened prismatic rail for smooth and precise panel processing - Support table with rollers for easy handling and stability when cutting large workpieces - High-performance drive motor with high torque for optimal cut quality - Foldable parallel fence with adjustment, ideal for working with larger panels - Handwheel with scale for tilting the main blade up to 45° - Telescopic longitudinal fence with two stop flaps for guaranteed precise cutting - Stable saw unit with tiltable elements on both sides, made of cast iron - Table width extension for cuts up to 1200 mm included in the delivery scope - Large, precision-machined and polished cast iron table for stability and cutting accuracy - Standard version equipped with a separately driven 0.75 kW scoring unit and a powerful 5.5 kW main saw, both adjustable using a convenient handwheel Applications of panel saws with scoring unit This panel saw is the ideal tool for professionals who value quality, precision, and reliability in wood processing. Technical specifications Ffjdpfx Astz Sm Ajb Sjt SLIDING TABLE LENGTH: 2000 mm CUTTING WIDTH: 1250 mm BLADE TILT: 0-45° MAX CUTTING HEIGHT AT 90°: 80 mm MAX CUTTING HEIGHT AT 45°: 56 mm MAX BLADE DIAMETER: 315 mm MAX SCORING BLADE DIAMETER: 125 mm MAIN BLADE SPEED: 4000/6000 rpm SCORING BLADE SPEED: 8000 rpm MAIN MOTOR POWER S1/S6: 5.5 kW / 9 HP SCORING MOTOR POWER (S1/S6): 0.75 kW / 1.2 HP WEIGHT: 460 kg

Sąlyga: naujas, Gamybos metai: 2025, Universal arbor press made of high-quality cast iron. Products in this series offer extensive capabilities in one reliable and affordable device. Simple to operate for tasks such as bushing insertion, bending, straightening, and reaming. Machine Features - For assembly and disassembly of bearings, bushings, and pins - High-quality cast iron construction - Work table adjustable to four positions - Suitable for use in all workshops Technical Specifications - Pressing force: 3 t - Maximum workpiece height: 285 mm - Distance from ram axis to column surface: 165 mm - Table diameter: 163 mm - Ram dimensions: 38×38 mm Fsdpfxjv Hqdhj Ab Sjft - Largest hole in table: 44 mm - Height with ram fully lowered: 615 mm - Base dimensions: 455×300 mm - Weight: 65 kg Manufacturer: Cormak

Sąlyga: naujas, Gamybos metai: 2025, The railway mechanical jack is a robust, fully mechanical device designed for lifting heavy loads. Its steel construction and precise crank mechanism ensure stable and safe operation both onsite and in workshops. It is ideal for railway, construction, and industrial applications. Key features of the railway mechanical jack: ✅ Mechanical design – no need for electrical power supply, enabling full independence in the field. ✅ High load capacity – ideal for handling heavy structural components, machinery, and vehicles. ✅ Precise adjustment – allows for accurate setting of lifting height. ✅ Ratchet safety mechanism – prevents accidental lowering of the load. ✅ Weather resistance – thanks to a robust steel housing and powder-coated finish. ✅ Easy operation and maintenance – the straightforward mechanism ensures years of reliable operation. Technical data MODEL: MJ3 Rated load capacity: 3,000 kg Ffjdpfexqxc Aex Ab Sjt Head width: 83 mm Base width: 130 (155) mm Overall height: 720–1075 mm Lifting range (toe): 55–410 (20–375) mm Toe length: 60 (50) mm Body thickness: 45 mm Base length: 138 (130) mm Gearbox height: 285 mm Body width: 200 mm Gearbox axis distance: 140 mm Bracket length: 230 (270) mm Side housing length: 126 mm Net weight: 20.5 kg

Sąlyga: naujas, Gamybos metai: 2025, The table saw is exceptionally easy to operate and user-friendly. This machine incorporates numerous solutions typically found in more expensive equipment of this type. The circular saw comes with a table, right-hand table extension, and angle fence. Machine Description This innovative circular saw combines power, precision, versatility, and a compact design. It is designed for small woodworking shops, furniture manufacturers, and craftsmen. The machine uses many features usually reserved for higher-end models in this class. An excellent price-to-performance ratio is achieved without compromising on quality or versatility. Included: Carbide-tipped saw blade 250 x 30 x 2 mm Technical Specifications MAXIMUM BLADE DIAMETER/BORE 254 mm SPEED 4000 rpm BLADE TILT RANGE 90 – 45° MAXIMUM CUTTING DEPTH AT 45° 56 mm MAXIMUM CUTTING DEPTH AT 90° 80 mm SLIDING TABLE TRAVEL 620 mm MAXIMUM RIP WIDTH TO THE RIGHT OF BLADE 610 mm TABLE HEIGHT 890 mm MOTOR POWER 2.2 kW (S1) / 3.1 kW (S6) POWER SUPPLY 400 V WEIGHT Ffedpfsvxhhbex Ab Sst 125 kg DIMENSIONS 1090 x 1330 x 910 mm

Sąlyga: naujas, Gamybos metai: 2025, CORMAK HBS260 band saw for cutting pipes, profiles, and bars is widely used in all metalworking shops where precision, quality, and cutting speed are essential. The model features a swiveling arm adjustable from 0-60°. The design of the saw bow ensures accurate and quiet operation. It comes with a removable chip tray for easy cleaning! Machine Features This horizontal metal band saw with a swiveling arm allows for cutting perpendicular or at any angle between 0 and 60° to the material axis. The workpiece can be fed manually or with any mechanical device, while the saw blade feed operates automatically. The blade guides are fitted with special carbide inserts and bearings, which greatly improve blade tracking, longevity, straightness, and the quality of the cut. Carbide blade guides significantly reduce wear on both the machine and the blade. The machine is equipped with a high-performance coolant pump with a closed-cycle cooling system. The saw’s arm is cast from a single piece of cast iron, and, combined with a 27 mm wide band saw blade, it is fully suitable for serial cutting of both profiles and solid materials. The vice is mounted on an adjustable bed with a quick-release clamp. Blade guides are equipped with carbide inserts and rolling bearing systems. It is the CARBIDE BLADE GUIDES that ensure cutting precision and straightness. The upper part of the base is shaped to form a tray for collecting coolant and chips generated during the cutting process. To the base, a sturdy cast iron work table with a swiveling arm is mounted, along with a control panel on a separate arm. During cutting, the main cutting motion is performed by the moving saw blade, while arm feed is via gravity. The speed of arm descent (cutting speed) is adjusted using a hydraulic cylinder. Feed rate is controlled from the saw’s control panel. There are two blade speeds to choose from: 35 and 70 m/min. In the lower end position of the arm (after cutting the material), the drive to the blade is automatically switched off. Safety is ensured by saw blade guards and microswitches that stop the motor after the cutting cycle or when any guard is opened. Additional protection consists of the automatic saw shut-off in the event of blade breakage. Band saw blade size [mm]: 2520 x 27 x 0.9 Blade tension: mechanical (manual) Blade speeds [m/min]: 35, 70 Arm descent adjustment: stepless – hydraulic cylinder Vice base height [mm]: 860 Saw wheel diameter [mm]: 300 Saw frame swivel [°]: 0-60 Power supply: 3-phase 400V Main motor power [kW]: 1.1/1.5 Coolant pump motor power [kW]: 0.05 Dimensions with base [cm]: 150x80x140 Fsdpfx Asudi Uzsb Seft Weight [kg]: gross/net - 210 / 180 kg Additionally: - 2 pcs M42 saw blades - 5L Emulgol coolant - Magnetic chip collector ZW580

Sąlyga: naujas, Gamybos metai: 2025, Ultra-robust, reliable, and modern semi-automatic metal band saw with automatic raising and lowering of the saw arm. The saw arm swivels both left and right from -45º to +60º. This machine is indispensable in any metalworking shop, making it ideal for cutting pipes, profiles, and solid materials. Product Features The CORMAK S-200RH saw is equipped as standard with automatic raising and lowering of the arm, as well as a height regulator enabling the arm to be raised to a level matching the material being cut. Thanks to the automatic hydraulic damper, manual operation is simplified to feeding and clamping the material in the vise. The arm is made from a single cast iron piece and, together with a refined, massive, and stable construction, ensures exceptional rigidity of the S-200R band saw, resulting in dependable operation and very high cutting precision. The innovation and production of CORMAK PREMIUM LINE semi-automatic and automatic band saws, manufactured according to ISO:90001 and ISO:140001 certified standards, guarantees safety, quality, and reliability. The use of M3V series motors from ABB—a globally recognized and respected manufacturer, and one of the world leaders—guarantees long, trouble-free operation. As the manufacturer and sole representative in the Polish market, we guarantee product authenticity and provide professional, well-trained warranty and post-warranty service. Technical Data TYPE – semi-automatic ARM LIFTING AND LOWERING – hydraulic with stepless adjustment BAND SPEED – 36/70 mm/min MITER CUTTING – left 45° to right 60° VISE – hydraulic MINIMUM CUTTING DIAMETER – Ø5 mm MINIMUM MATERIAL LENGTH IN VISE – 30 mm VISE BASE HEIGHT – 780 mm BAND SIZE – 27x0.9x2910 mm TOTAL POWER – 2.1 kW DIMENSIONS (LxWxH) – 1600 x 800 x 1400 mm WEIGHT – 530 kg Cutting Capacity Angle 0º -----ø250 320 x 240 240 x 240 45º L ø200 220 x 120 190 x 190 45º R ø220 235 x 120 210 x 210 60º R ø110 155 x 110 100 x 100 Standard Equipment • Control console on a separate pedestal • Integrated hydraulic unit • Hydraulic arm operation (up-down) with stepless lowering speed regulation • Arm position memory (arm returns after cutting to a preset height) Fodpsi D D A Sofx Ab Ssft • Miter cutting L/R 45° - 0° - 45° - 60° • Band cleaning brush • Cooling system • Bimetal band saw blade • CE declaration of conformity • Operating and maintenance documentation The price listed is NET, does not include shipping costs. For more information, please contact us by phone or email. Visit our website to see our full offer.

Sąlyga: naujas, Gamybos metai: 2025, The PS12E-1600 panel saw is a professional woodworking tool distinguished by its versatile specification and excellent functionality. This table saw is engineered to meet the needs of both professional craftsmen and hobbyist carpenters. Main features of the PS12E-1600 scoring panel saw for wood: Two saw blades: The machine is equipped with two saw blades – a main blade and a scoring blade. Safe machine front: On the front of the saw, you will find a safety switch, a height adjustment knob for the blade (up to 100 mm), and a blade tilt lock, ensuring user comfort and enhanced operational safety. Adjustable bevel cutting: Located on the side panel, a knob enables blade tilt angle adjustment up to 45°. Dust extraction port: The saw is designed for connection to a dust extraction system. Large bearing-mounted sliding table: One of the main advantages is the large, bearing-mounted sliding table with support, ensuring precise cutting of large-format panels and materials. Fence with angle scale: The fence is fitted with an integrated angle scale for precise angular adjustments. Side fence with precision scale: For repeatable length cuts, the machine is equipped with a side fence featuring a precision scale. Blade change: Blade replacement is quick and efficient—simply remove the metal tabletop and unscrew the blade. Mitre cutting up to 45°: The saw allows mitre cuts up to 45°, practical for complex woodworking projects. Maximum fence length 1600 mm: The long guide enables cutting planks and panels up to 1600 mm in length. Control panel: The machine's control panel is located at the bottom of the saw and features an emergency stop switch, an angle-cut adjustment knob (up to 45°), and a blade height adjustment knob with lock. 3.8 kW motor: The blades are powered by a robust 3.8 kW motor running at 400V, providing both high performance and cutting efficiency. Applications of the PS12E-1600 panel saw: The PS12E-1600 panel saw combines versatility and precision, enabling a wide range of cuts for various carpentry and woodworking projects. Its large working surface, adjustable cutting angles, and the option for dust extraction make it an excellent choice for professional joiners and craftsmen. Technical specifications: Sliding table length [mm]: 1600 Cutting width right of blade [mm]: 1260 Saw tilt angle [°]: 45 Cutting height at 45° [mm]: 80 Cutting height with 315 mm saw blade at 90° [mm]: 100 Cutting height with 300 mm saw blade at 90° [mm]: 95 Max. blade size [mm]: 315 x 30 Max. scoring blade size [mm]: 100 x 20 Main blade speed [rpm]: 4500 Scoring blade speed [rpm]: 5800 Motor power [S1/S6]: 3.8 kW / 6.1 HP Power supply: 3-phase, 400V Weight [kg]: 275 Warranty [months]: 12 Ffedpevuf Uqjfx Ab Sot

Sąlyga: naujas, Funkcionalumas: visiškai funkcionalus, Gamybos metai: 2025, Hinge Boring Machine CORMAK BBM40MAN – Precision Machining of Furniture Fittings The CORMAK BBM40MAN hinge boring machine is a compact, efficient, and user-friendly woodworking drill designed for precision drilling of holes for furniture hinges. The machine is ideal for furniture production, providing repeatable drilling accuracy and stable tool guidance. Thanks to its intuitive design and robust components, the BBM40MAN ensures high work quality while remaining simple to operate. Key advantages of the machine - Precise drilling for furniture hinges – an adjustable depth stop located at the rear allows for full control over drilling parameters, minimizing the risk of material damage. - Compact and stable construction – a rigid base with a large working table (350 x 300 mm) ensures both comfort and safety during operation. - Powerful 1.1 kW motor – unmatched among comparable machines, the 1.1 kW motor provides sufficient torque for working with Blum-type hinges and other fitting systems. - Three working spindles – enable simultaneous drilling for the main hinge and side guides. Construction and Technology The CORMAK BBM40MAN model is designed with simplicity of use and durability in mind. The mechanical head travel of 110 mm and manual controls ensure full command over the work cycle. A 10 mm tool holder diameter allows the use of standard hinge drill bits. Its compact overall dimensions (370 x 500 x 600 mm) and weight of 21.5 kg make this hinge boring machine ideal for on-site assembly jobs as well. Precision and Performance Thanks to the optimally selected spindle speed (3000 rpm) and the option for manual adjustments, the operator can quickly and accurately drill holes for any standard hinge type. Adjustable drilling depth enables easy adaptation to various front thicknesses and hinge types. Stable workpiece clamping and parameter control minimize assembly errors and improve overall process efficiency. Application The CORMAK BBM40MAN hinge boring machine is suitable for use in: - Production of kitchen, bathroom, and office furniture - Carpentry workshops and maintenance departments - Service shops specializing in hardware assembly - Schools and training centers related to woodworking Standard Equipment - 3-spindle hinge boring head - Mechanical guide travel (110 mm) - Adjustable depth stop - 350 x 300 mm work table - Powerful 1.1 kW (230 V) motor - Manual controls and workpiece clamping - Set: 35 mm cutter + two 2 mm drills for BLUM hinges Technical Data Table Dimensions: 350 x 300 mm Guide Travel: 110 mm Distance between spindle and table: 130 mm Tool holder diameter: 10 mm Number of spindles: 3 Max. drilling depth: 10 mm Spindle speed: 2800 rpm Workpiece clamping: manual Control: manual Motor: 1.1 kW Power supply: 230 V Overall dimensions: 370 x 500 x 600 mm Weight: 21.5 kg Ffjdpexzdicofx Ab Sot

Sąlyga: naujas, Gamybos metai: 2025, CORMAK HBS260 bandsäge zum Schneiden von Rohren, Profilen und Stangen wird in allen Schlossereibetrieben eingesetzt, bei denen Präzision, Qualität und Schnittgeschwindigkeit wichtig sind. Das Modell verfügt über einen schwenkbaren Arm von 0-60°. Die Rahmenkonstruktion sorgt für einen präzisen und leisen Betrieb. Sie verfügt über eine herausnehmbare Spänewanne für eine einfache Reinigung! Maschineneigenschaften Die horizontale Metallbandsäge mit schwenkbarem Arm ermöglicht das Schneiden in einer zur Achse des Werkstücks senkrechten Ebene sowie in jedem Winkel zwischen 0 und 60°. Das zu schneidende Material kann manuell oder mit jedem mechanischen Vorschub zugeführt werden, der Werkzeugvorschub erfolgt automatisch. Die Bandführungen sind mit speziellen Hartmetallplatten und Wälzlagern ausgestattet. Dies wirkt sich entscheidend auf die Bandführung, deren Lebensdauer, Geradheit, Präzision und Schnittqualität aus. Die Hartmetall-Führung minimiert den Verschleiß der Maschine und des Sägeblatts. Die Maschine ist mit einer leistungsstarken Kühlmittelpumpe mit geschlossenem Kühlkreislauf ausgestattet. Der durchgehende Gusssägearm in Kombination mit dem 27 mm breiten Sägeband ermöglicht Serienkopfschnitte von Profilen und Vollmaterialien. Der Schraubstock befindet sich auf einer einstellbaren Basis und ist mit einer Schnellspannvorrichtung ausgestattet. Die Bandführungen sind mit Hartmetallplatten (gesinterte Hartmetalle) und Rollsystem ausgestattet. ZENTRIERTE HARTMETALLFÜHRUNGEN sorgen für die Präzision und Geradheit des Schnitts. Die Form des oberen Gestellbereichs dient als Wanne zur Aufnahme von Kühlmittel und Spänen, die beim Schneiden entstehen. Ein Gusseisentisch mit schwenkbarem Arm sowie ein Bedienfeld auf einem separaten Arm sind am Grundkörper befestigt. Während des Schneidvorgangs ist die Bewegung des Sägebands sowie der Absenkvorgang des Arms die Hauptschnittbewegung. Die Absenkgeschwindigkeit des Arms (Schnittgeschwindigkeit) wird durch einen Hydraulikzylinder geregelt. Die Vorschubgeschwindigkeit lässt sich am Bedienfeld einstellen. Es sind zwei Schnittbandgeschwindigkeiten wählbar: 35 und 70 m/min. In der unteren Armstellung (nach Beendigung des Schnitts) wird der Bandantrieb automatisch abgeschaltet. Die Sicherheit wird durch Bandabdeckungen und Mikroschalter gewährleistet, die den Motor nach Abschluss des Schnittzyklus oder beim Öffnen einer Abdeckung stoppen. Zusätzlich sorgt eine automatische Abschaltung der Maschine beim Bandriss für Schutz. Schnittbandmaß [mm]: 2520 x 27 x 0,9 Bandspannung: mechanisch (manuell) Bandgeschwindigkeiten [m/min]: 35, 70 Einstellbarer Armabwurf: stufenlos – Hydraulikzylinder Schraubstockhöhe [mm]: 860 Sägeraddurchmesser [mm]: 300 Sägerahmenschwenkung [°]: 0-60 Stromversorgung: 3 Phasen 400V Hauptmotorleistung [kW]: 1,1/1,5 Kühlmittelpumpenleistung [kW]: 0,05 Abmessungen inkl. Sockel [cm]: 150x80x140 Gewicht [kg] brutto/netto: 210 / 180 kg Fsdpemrnk Eofx Ab Ssft *Bitte beachten Sie, dass die Maschine serienmäßig ohne CEE-Stecker geliefert wird, da es verschiedene Ausführungen gibt. Sollten Sie den Stecker wünschen, geben Sie dies bitte vor dem Kauf oder während des Bestellvorgangs beim Verkäufer an. Der Preis ist ein Nettopreis. Versandkosten sind nicht im Preis enthalten. Für weitere Informationen kontaktieren Sie uns bitte telefonisch oder per E-Mail. Wir laden Sie ein, sich mit unserem Angebot auf unserer Webseite vertraut zu machen.

Sąlyga: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, Professional industrial panel saw for processing high-density boards, MDF boards, ABS and PVC panels, solid wood, and other materials up to a maximum size of 3200x2800 mm. The machine features electrically powered saw blade lifting and lowering. MJ 45-KD3 SLIDING TABLE SAW EQUIPPED WITH A POLISH-MADE 'KACPEREK' MAIN MOTOR. Specifications of the MJ45-KD3 Sliding Table Saw with Scoring Unit: The MJ45KD3 sliding table saw is a professional-grade machine designed for cutting various materials, including high-density boards, MDF boards, ABS and PVC panels, solid wood, and other wood-based materials of similar structure and hardness. This advanced saw offers numerous innovative solutions and exceptional precision, making it an excellent tool for both professionals and skilled hobbyists. Key advantages of the MJ45KD3 sliding table saw: - 'Kacperek' motor, made in Poland: Fitted with a top-quality 'Kacperek' main motor produced in Poland, providing reliability and long-lasting performance. The motor ensures optimal machine power output at various speeds. - Robust construction: The frame is constructed from closed-section profiles and a heavy machine body, ensuring outstanding rigidity and stability for precise cutting operations. - Large sliding table: Features a large and rigid sliding table with dimensions of 3200x420 mm, designed to handle sizable sheet materials with ease. - Innovative control features: The MJ45KD3 stands out with its modern design and innovative control elements, delivering high operating comfort. - High performance: The powerful saw unit accommodates large saw blades up to 350 mm in diameter, with a maximum cutting height of 100 mm, effortlessly tackling diverse cutting tasks. - Tiltable upper blade guard: The newly designed, tiltable upper blade guard provides maximum flexibility and work safety. Fjdpfjvuf Iqox Ab Ssft - Advanced saw unit: The saw unit is equipped with a patented tilt segment and automatic blade raising, enabling the use of primary saw blades ranging from 250 mm to 350 mm in diameter, paired with a 125 mm scoring blade. The MJ45KD3 sliding table saw is a premium tool, combining precision, durability, and high performance, making it ideal for both professional users and daily woodworking operations. Its advanced technological solutions set it apart as a top-tier model among sliding table saws. Technical specifications: Blade diameter / bore: 350 / 30 mm Blade tilting range: 0 - 45° Main blade speed: 4000 / 4800 rpm Scoring blade diameter / bore: 125 / 20 mm Scoring blade speed: 7500 rpm Main table dimensions: 945 x 720 mm Sliding table: 3200 x 420 mm Max cutting height: 100 mm Rip cutting width at fence: 1250 mm Crosscut with crosscut fence: up to 3200 mm Dust extraction port under table: Ø100 mm Dust extraction port at blade guard: Ø80 mm Minimum air speed: 20 m/s Minimum airflow rate: 565 mm³/h Main motor power S1/S6: 5.5 kW / 9 HP Scoring unit motor power S1/S6: 1.1 kW / 1.8 HP Weight: 850 kg

Sąlyga: naujas, Gamybos metai: 2025, The PS12E-3000 panel saw is a professional woodworking tool that distinguishes itself with a powerful specification and the capability to perform precise cuts on a large scale. This advanced circular saw is designed for a range of wood processing tasks and is the ideal solution for demanding users. Key features of the PS12E-3000 woodworking panel saw: - Dual saw blades: The machine is equipped with two saw blades – a main blade and a scoring blade – offering broad cutting capabilities for various types of wood-based materials. - Large sliding table: One of the main advantages of this model is its exceptionally large, bearing-mounted sliding table with support, which allows for precise machining of large-format boards up to almost 3000mm in length and other large wood-based panels. - Additional scorer: The auxiliary scoring blade makes the saw perfect for cutting furniture boards and chipboards, eliminating the risk of edge chipping and ensuring clean cuts. - Blade tilting: The main saw blade can be tilted from 90° to 45°. - Maximum fence length: The machine is equipped with an impressive 2300 mm fence length. - Blade exchange: The blade changing process is quick and efficient, thanks to the removable metal table and easy blade removal. - Saw guard: The machine is fitted with an effective blade guard, which can also be connected to an extraction system to help keep the work area clean. - Powerful motor: The blades are driven by a robust 3.8 kW motor (400V), ensuring smooth operation and efficient cutting. - Control panel: The control panel is located on the lower part of the saw and includes an emergency stop, a knob for angled cuts (45°), and a blade height adjustment knob with lock. - Additional measuring tools: All fences are equipped with length and angle scales, allowing for quick adjustment of required angle and length without extra measurements. - Dust extraction compatibility: The saw is designed for connection to a dust and chip extraction system with a 100 mm suction port, ensuring cleanliness in the workspace. Application of the PS12E-3000 panel saw: The PS12E-3000 is a sophisticated tool combining durability, precision, and high performance, making it the ideal choice for professional carpenters and woodworkers. Its versatility and advanced features make it suitable for a wide range of wood processing projects, both in industrial and workshop settings. SLIDING TABLE DIMENSIONS 3000 x 270 mm MAIN TABLE DIMENSIONS 800 x 385 mm AUXILIARY SIDE TABLE DIMENSIONS 880 x 800 mm CUTTING WIDTH 1220 mm SAW TILT 0-45° CUTTING HEIGHT AT 90° 100 mm CUTTING HEIGHT AT 45° 80 mm Ffjdpfx Aevugc Aeb Sjt MAXIMUM BLADE SIZE 315 mm MAXIMUM SCORER SIZE 100 mm MAIN SAW SPEED 4000 rpm SCORER SAW SPEED 5800 rpm MOTOR POWER S6 5.3 kW / 7.1 HP MOTOR POWER S1 3.8 kW / 5.1 HP POWER SUPPLY 400 V WEIGHT 309 kg

Sąlyga: naujas, Gamybos metai: 2025, PREMIUM LINE Series Machine. Cormak S200R Manual Bandsaw for industrial applications. This metal-cutting bandsaw features high cutting accuracy, ensured by a robust cast iron rotating table synchronized with a pivoting arm. The bandsaw is designed for use in large industrial facilities, capable of operating 16h/24h. Cutting angles range from -45º to the left up to 60º to the right. Machine Features The CORMAK S-200 R MANUAL bandsaw (CE-compliant) enables perpendicular cutting relative to the axis of the material or miter cutting at any angle from -45° to +60°. The workpiece can be fed manually or by any automated feeding device. The cutting feed operates by gravity via an oil flow through a dual-chamber hydraulic cylinder. The appropriate arm descent speed is achieved using a valve regulating oil flow between chambers. The operator starts the machine by pressing the start button and sets the cutting speed. Upon finishing the cut, the machine stops automatically, and the operator manually lifts the arm to the starting position. Material feeding is manual. The vise is mounted on an adjustable bed and features a quick-clamp system. Blade guides are equipped with carbide inserts and roller bearings, where the CARBIDE BLADE GUIDES are responsible for high cutting precision and straightness. The arm features an automatic blade tension sensor and is inclined by 25 degrees, extending blade life. A cleaning brush is mounted under the arm for optimal blade cleanliness and function. The machine’s drive is transmitted through a worm gearbox filled with gear oil. The machine is equipped with a three-phase motor with double winding and two cutting speeds. Thermal overload protection on the motor. The saw offers two blade speeds: 35 and 70 m/min. Construction: the arm, vise, and rotary table are all cast iron. The machine features a closed-loop coolant system. It is supplied with a stop and ruler for precise length adjustment of the workpiece. The machine base is a rigid steel sheet cuboid, housing a coolant tank with a pump system. Safety during operation is ensured by an electrical system meeting all CE requirements. The machine is equipped with a limit switch that stops the machine after each cutting cycle, an emergency stop button (“mushroom” type), and multiple micro-switches that disable operation, e.g., when the belt or band covers are open. Technical specifications: Fodsfy Ttiepfx Ab Sjft TYPE: gravity fed ARM LIFT/DROP: gravity with stepless arm descent adjustment BLADE SPEED: 36/70 m/min MITER CUTTING RANGE: left 45° to right 60° VISE: manual MINIMUM CUTTING DIAMETER: Ø 5 mm MINIMUM MATERIAL LENGTH IN VISE: 30 mm VISE BASE HEIGHT: 890 mm BLADE SIZE: 27x0.9x2910 mm TOTAL POWER: 2.1 kW DIMENSIONS (LxWxH): 1600 x 800 x 1400 mm WEIGHT: 500 kg Maximum cutting capacity [mm]: Angle 0º ø250 320 x 240 240 x 240 45º L ø200 220 x 120 190 x 190 45º R ø220 235 x 120 210 x 210 60º R ø110 155 x 110 100 x 100 For more information, please visit our website.

Sąlyga: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, Bandsäge für Metall mit optimalem Schnittbereich, häufig eingesetzt in Tischlereien, Produktions- und Handwerksbetrieben. Maschinenbeschreibung Die CORMAK BS 128HDRC Bandsäge für Metall bietet einen optimalen Schnittbereich und ist speziell für professionelle Anwender konzipiert. Sie zeichnet sich durch Effizienz und eine besonders einfache Handhabung aus. Das beidseitige Schwenken des Sägebügels ist ein großer Vorteil beim Gehrungsschneiden. Trotz kompakter Abmessungen sorgt das hohe Eigengewicht (103 kg) für einen sehr stabilen und vibrationsfreien Betrieb auch beim Schneiden größerer Werkstücke. Das Material kann sowohl manuell als auch automatisch zugeführt werden. Der Sägevorschub erfolgt gravitationsbasiert über einen zwei-Kammer-Hydraulikzylinder mit Ölstrom. Die Steuerung des Sägebügel-Absenkens wird durch ein Ventil geregelt, das den Ölfluss zwischen den Zylindern kontrolliert. Ein gerader Schnitt wird durch ein Lagersystem zur Bandführung gewährleistet. Die Maschinen sind standardmäßig mit einem Endschalter sowie einem nach IP54 zertifizierten EIN/AUS-Schalter ausgestattet. Der schwenkbare Sägebügel ermöglicht das doppelseitige Gehrungsschneiden im Bereich von -45° bis +60°. Technische Daten Sägebandabmessung: 1640×13×0,65 mm Schnittgeschwindigkeit: 23/34/54 m/min Antriebsleistung: 0,55 kW / 400 V Absenkregelung: stufenlos, hydraulisch Gehrungsbereich: -45° bis +60° Abmessungen (L×B×H): 942×442×548 mm Gewicht: 103 kg Maximaler Schnittbereich [mm] Winkel 0° ….. ø125 mm ….. 100×150 mm …. 100×100 mm -45° ….. ø90 mm ….. 90×75 mm ….. 90×90 mm +45° ….. ø90 mm ….. 90×75 mm ….. 90×90 mm +60° ….. ø55 mm ….. 55×55 mm ….. 55×55 mm Serienausstattung - Hydraulikzylinder der 3. Generation - Tisch für Vertikalschnitte - Schnellspann-Schraubstock - Kühlmittelsystem - Werkstückanschlag - Automatische Endabschalter - Moderner Motorthermoschutz - Fahrgestell mit vier Lenkrollen - Bedienungsanleitung Fodjwq A Dyepfx Ab Seft Der Preis versteht sich netto. Versandkosten sind nicht im Preis enthalten. Für weitere Informationen stehen wir Ihnen telefonisch oder per E-Mail zur Verfügung. Besuchen Sie auch unser Online-Angebot auf unserer Webseite.

Sąlyga: naujas, Gamybos metai: 2025, The Cormak TS255 table saw is a precision woodworking machine distinguished by advanced features and robust construction. Key advantages of the professional TS255 400V table saw for cutting wood: Precise Height and Angle Adjustment: The saw is fitted with an intuitive handwheel enabling precise adjustment of both height and cutting angle, ensuring accuracy for a wide variety of cutting tasks. Parallel Fence: The machine features a parallel fence, guaranteeing stable and accurate material guidance during cutting. Cast Iron Table and Table Extension: The worktable is made of durable cast iron and precision-ground to ensure smooth material feed. Additionally, the machine comes equipped with a table extension, increasing the working surface area. Stable Construction: The saw is designed with stability and durability in mind, making it suitable for demanding operations in various woodworking shops. Integrated Side Table: An additional benefit is the integrated side table, which significantly expands cutting capabilities by allowing work with larger components. Powerful Motor: Driven by a three-phase electric motor rated at 2.2 kW and 4,000 rpm, the TS255 delivers effective cutting of wooden components and even the most demanding boards in any workshop. Application of the precision table saw with a 254 mm circular saw blade: The Cormak TS255 table saw is a versatile machine, distinguished by its precision and solid build. With its adjustable height and cutting angle, as well as a stable construction, it is ideal for a wide range of joinery workshops. Additionally, the integrated side table increases the range of cutting capabilities. It is an indispensable machine for professional carpenters and demanding hobbyists alike. Technical Data Maximum blade diameter: 254 mm Blade speed: 4,000 rpm Blade tilt range: 90°–45° Maximum cutting depth at 45°: 50 mm Maximum cutting depth at 90°: 80 mm Worktable dimensions: 350 x 800 mm Sliding table dimensions: 240 x 1320 mm Maximum cutting width: 1250 mm Maximum cutting length: 1300 mm Ffjdpfx Asvxhlgob Set Continuous duty motor power S1: 2.2 kW Power supply: 400 V Weight: 180 kg Dimensions: 1550 x 1900 x 820 mm

Sąlyga: naujas, Gamybos metai: 2025, Universal arbor press made from high-quality cast iron. Products in this series offer extensive capabilities within one reliable and cost-effective device. Easy to operate for processes such as bushing, bending, straightening, and reaming. Machine Features - Suitable for installation and removal of bearings, bushings, and pins Fodpfsv Hqfrjx Ab Seft - High-quality cast iron construction - Table adjustable to four positions - Suitable for all types of workshops Technical Specifications - Pressing force: 3 t - Maximum ram height (from fixed table surface): 310 mm - Ram reach: 145 mm - Fixed table dimensions: 190×180 mm - Rotary table dimensions: Ø166×20 mm - Rotary table hole diameters: 18, 25, 36, 46 mm - Ram dimensions: 38×38 mm - Base dimensions: 455×195 mm - Height with ram lowered: 570 mm (without lever) - Weight: 63 kg Manufacturer: Cormak

Sąlyga: naujas, Gamybos metai: 2025, The 10-ton ratchet jack is an exceptionally robust mechanical device designed for lifting heavy structures, machinery, and vehicles. Manufactured from damage-resistant steel, it ensures safety, stability, and long service life even under the most demanding working conditions. Ideal for railway, construction, and industrial applications. Advantages of the 10-ton ratchet jack: ✅ 10,000 kg lifting capacity – perfect for handling heavy machinery, structures, and vehicles. ✅ Mechanical design – operates independently of any power supply, ready for use anywhere. ✅ High level of safety thanks to a ratchet locking system. ✅ Precise height adjustment allows for accurate load positioning. ✅ Excellent resistance to external factors – moisture, dust, vibrations, and low temperatures. ✅ Easy transport – compact dimensions and ergonomic construction. ✅ Suitable for multiple industries. Technical data MODEL MJ10 Rated lifting capacity: 10,000 kg Head width: 120 mm Base width: 140 (210) mm Overall height: 795–1155 mm Lifting range of toe: 70–430 (30–390) mm Toe length: 80 (75) mm Ffsdpfxsxqxwms Ab Set Body thickness: 73 mm Base length: 175 (170) mm Gearbox height: 330 mm Body width: 252 mm Gearbox axle distance: 185 mm Support length: 220 (280) mm Side housing length: 250 mm Net weight: 45 kg