Šilto Oro pirkti naudotą (11 910)

Sąlyga: naujas, Funkcionalumas: visiškai funkcionalus, galia: 114 kW (155,00 AG), kuras: dyzelinas, Įranga: Tipinė plokštelė prieinama, dokumentacija / vadovas, REMKO "CLK 120" šildymo patranka yra galingas šildytuvas, tinkantis naudoti salėse, dirbtuvėse, šventinėse palapinėse, medžiagų sandėliavimui, šiltnamiuose ir pan. Šiuo metu sandėlyje iš karto prieinami 3 vnt. Būklė: Naujas / nenaudotas iš sandėlio likučių / bankroto Komplektacija: 1 vnt. Remko CLK 120 šildymo įrenginys su dyzelinio kuro degikliu 1 vnt. Roth mobilus šildymo alyvos bakas 1000 L Gedjxgbbtjpfx Abmjuk 1 vnt. kambario termostatas su laidu Nominali šiluminė galia: 114 kW Oro našumas: 8050 m³/h Kuras: EL šildymo alyva Didžiausios degalų sąnaudos: 11,2 l/val. Išmetamųjų dujų nuostoliai: max. 9 % Dūmtraukio jungtis: Ø 200 mm Oro išleidimas: Ø 500 mm Maitinimo įtampa: 230 V Išmatavimai (A/P/G): apie 1350 x 920 x 2100 mm Svoris: apie 296 kg Įrenginį galima apžiūrėti iš anksto susitarus. Visi duomenys yra be garantijos. Pasiliekama teisė parduoti anksčiau.

Sąlyga: geras (naudotas), Reznor UDSA Gas Warm Air Heater UDSA Gas Warm Air Heater – Efficiency at Its Best The most renowned unit from REZNOR is the UDSA gas warm air heater, which ensures uniform air distribution in industrial halls. This easy-to-install recirculating air unit is available in 14 output sizes ranging from 7 to 97 kW, and comprises a heat exchanger, gas burner, and an exhaust fan. The combustion air can be sourced either from outside (standard) or from the installation area. The REZNOR UDSA warm air heater guarantees even air distribution in the heated hall. Its patented heat exchanger sets new standards in flow behavior and heat transfer, providing an efficiency rating of over 92%. UDSA: compact, revolutionary, and forward-looking. This new generation of units enables particularly economical direct heating of halls—meaning without a central heating system—using decentralized, modulating gas warm air heaters. REZNOR UDSA Gas Warm Air Heater: The Advantages: - Efficiency over 92% - Suitable for vertical installation - Low NOx emissions - Innovative combustion concept - Quiet operation - CE system certification, version B or C - Compact design for easy installation - Even heat distribution - Standard vertical and horizontal air deflection louvres - Modulating heating capacity down to 50% - EC technology - ErP ready These units are directly heated gas warm air generators (WLE) with fan-assisted atmospheric multi-gas burners. Installation of the gas WLE and the connection for gas and exhaust side must only be carried out by an authorized installation company. The gas WLEs are suitable for: - Operation with natural gas or LPG - Recirculated air operation - Inlet temperatures below 5°C with stainless steel heat exchanger * - Heating operation single-stage, or two-stage control* via room thermostat and heating control switch - Ventilation° control via ECOtronic TN-L° with day/night/week program - Flue gas discharge through the roof, versions B or C° - Flue gas discharge through external wall, version C° Gas WLE Type: UDSA064-4E Gas Device Type: BSP-C12-C32-C52-C62 Designation: DE Gas Category: I2ELL Gjdpfewb Amisx Abmjuk Gas Type: G20 natural gas Connection Pressure: 20 mbar Nozzle Pressure: 7.90 mbar Max. Rated Heat Input (Hs) QN: 77.69 kW Max. Rated Heat Input (Hi) QN: 70.00 kW Min. Rated Heat Input (Hs) QN: - Min. Rated Heat Input (Hi) QN: - Max. Rated Heat Output: 64.40 kW Min. Rated Heat Output: - Connection Voltage: 230V 1N, 50Hz Airflow Rate: 6810 m3/h Protection Class: IP20 Pin No. 0461BN0677 More products – new and used – can be found in our shop! International shipping costs on request!

Gamybos metai: 2020, veikimo valandos: 0 h, Sąlyga: naujas, For sale are 4 stationary 360S oil/gas hot air generators from Knoll. Purchased in 08/2022 from DEXES Berlin. Original price: €12,499 net/unit; Warranty valid until 07/2024. 3 units are unused (€11,000 net/unit); Gedoppv Hbepfx Abmsuk 1 unit has only been used 3 times; price for this unit is negotiable. Location: 95506 Kastl; Available individually; Self-collection preferred. The hot air generator is already equipped with an oil burner/nozzle and room thermostat.

Sąlyga: geras (naudotas), Gamybos metai: 2006, Funkcionalumas: visiškai funkcionalus, bendras svoris: 4 000 kg, šildymo galia: 198 kW (269,20 AG), didelė karšto oro krosnis malkoms ir likutinėms medžiagoms Gsdpfxjw Ucfde Abmouk Išoriniai matmenys apie 3,5 m x 1,5 m x 3 m Svoris 4 t su valdymo sistema su karšto oro ventiliatoriumi

Sąlyga: naujas, Funkcionalumas: visiškai funkcionalus, bendras svoris: 450 kg, Gamybos metai: 2022, mašinos/transporto priemonės numeris: 41728980, THERMOBILE, IMA-200 RHP GB 200-RHP, mobile warm air generator (400 V) with separate flue gas discharge, mounted oil burner RG 4, pre-filter for heating oil, radial fan, and plug-ready thermostat interface. Year of manufacture: 2022, Operating hours: 0 - Rated heat output: 200 kW - Air flow rate: 13,000 m³/h - Connection: 400 V - Pressure: 500 Pa - Weight: 450 kg Gsdjvnuq Iopfx Abmouk Technical Highlights of this Series: - Burner hood with oil drip tray - Outlet opening Ø 600 mm - Pre-equipped for recirculation operation (optional intake nozzle available, item no. TE41728445) - Thermostat connection prepared (plug connector) - Shock-protected electrical distribution - Robust design with large wheels for easy transport, even on rough terrain Accessories such as room thermostat, warm air hoses, tanks and tank heater, as well as exhaust pipes and rain cap are not included in this offer, but can be provided upon request. Note: The buyer can arrange collection of the item by a freight carrier. If you do not have contact with freight carriers, we will be happy to assist with addresses or obtain quotes for you.

Sąlyga: naujas, Funkcionalumas: visiškai funkcionalus, galia: 150 kW (203,94 AG), kuras: dyzelinas, Įranga: Tipinė plokštelė prieinama, dokumentacija / vadovas, REMKO "CLK 150" karšto oro patranka yra galingas šildytuvas, kuris gali būti naudojamas halėse, dirbtuvėse, paviljonuose, medžiagų džiovinimui, šiltnamiuose ir t.t. Šiuo metu sandėlyje yra 3 įrenginiai, galimas skubus atsiėmimas. Būklė: Naujas / nenaudotas, iš sandėlio valymo ar įmonės bankroto Komplektacija: 1 vnt. Remko CLK 150 šildymo įrenginys su dyzeliniu degikliu 1 vnt. Roth mobilus šildymo kuro bakas, 1000 l 1 vnt. Patalpos termostatas su elektros laidu Nominali šiluminė galia: 150 kW Oro našumas: 9710 m³/h Kuras: skystas kuras (Heizöl EL) Kuro sąnaudos: maks. 14,8 l/val. Išmetamųjų dujų nuostoliai: maks. 9 % Išmetimo jungtis: Ø 200 mm Oro išleidimas: Ø 500 mm Maitinimo įtampa: 230 V Matmenys (A/P/I): apie 1350 x 920 x 2100 mm Svoris: apie 312 kg Įrenginį galima apžiūrėti vietoje, suderinus laiką iš anksto. Gjdoxli I Sopfx Abmjuk Visa informacija pateikiama be garantijos. Įrenginys gali būti parduotas bet kuriuo metu.

Sąlyga: geras (naudotas), Kroll M 150 Mobilus karšto oro generatorius Panaudojimo sritys: Salėlių, palapinių ir statybviečių šildymas Apsauga nuo užšalimo sodininkuose ar bet kokio tipo sandėliuose Greitas naujų pastatų džiovinimas Papildomas šildymas šaltuoju metų laiku Kuras: šildymo alyva EL Nominali šiluminė galia: 135 kW Nominali šiluminė apkrova: 150 kW Alyvos sunaudojimas: 12,7 kg/h Oro srautas: 7 300 m³/h Elektros jungtis: 220 V / 6,1 A Galingumo suvartojimas: 1,38 kW Apsaugos klasė: IP 44 Matmenys: Ilgis: 2600 mm Plotis: 900 mm Aukštis: 1300 mm Svoris: 270 kg Gedpfx Ajxwkw Eebmouk Daugiau naujų ir naudotų prekių rasite mūsų parduotuvėje! Tarptautinis pristatymas – kaina pagal užklausą!

Sąlyga: paruoštas naudoti (naudotas), Gamybos metai: 2010, Mobile oil-fired warm air heater / heating system / heater 120 kW - Used unit from rental fleet - Year of manufacture: 2007 - For construction site heating / building sites / stables / tents / exhibitions / workshops / etc. Offer description: TB 110, mobile oil-fired warm air generator with separate flue gas discharge, mounted oil burner RG 2, heating oil pre-filter with quick vent and single-line system, radial fan and pre-wired thermostat connection. Rated heat input: 120 kW Airflow rate: 6500 m³/h Connection: 230 V/50 Hz Motor output: 1.1 kW Weight: 235 kg Dimensions (LxWxH): 200 x 90 x 115 mm Guodpfx Abjvnu Akemok Accessories such as room thermostat, hot air hoses, tanks and tank heater, flue gas pipes and rain cap are not included in this offer but can be supplied on request. Note: The buyer can arrange collection of the item by freight forwarder. If you do not have contact with forwarding agents, we are happy to assist with contact details or make inquiries on your behalf.

Sąlyga: geras (naudotas), Reznor UDSA Gas Warm Air Heater UDSA Gas Warm Air Heater – Efficiency at Its Peak Gedpfx Abewb A Hijmouk The UDSA gas warm air heater is REZNOR’s most renowned unit, ensuring uniform air distribution in industrial halls. This recirculating unit is easy to install and available in 14 power ratings from 7 to 97 kW. It comprises a heat exchanger, gas burner, and an exhaust fan. Combustion air can be supplied as standard from outside or from the installation room. The REZNOR UDSA warm air heater guarantees even air distribution in the heated hall. Its patented heat exchanger sets new standards in airflow and heat transfer, delivering an efficiency of over 92%. UDSA: compact, revolutionary, and trend-setting. This generation of units allows halls to be heated in a particularly economical way using decentralised, modulating gas-fired warm air heaters—without the need for a central heating system. REZNOR UDSA Gas Warm Air Heaters — Key Advantages: - Efficiency greater than 92% - Suitable for vertical installation - Low NOx emissions - Innovative combustion concept - Quiet operation - CE system certification, types B and C - Compact design for easy installation - Uniform heat distribution - Standard vertical and horizontal air deflection louvres - Modulating heat output down to 50% - EC technology - ErP Ready These units are directly fired gas warm air heaters with fan-assisted atmospheric multigas burners. Installation, as well as the gas and exhaust connections, must be carried out by a certified installation company. The gas fired warm air heaters are suitable for: - Operation with natural gas or LPG - Recirculation mode - Inlet temperatures below 5°C with stainless steel heat exchanger * - 1-stage or 2-stage* heating mode, controlled by room thermostat and heating control switch - Ventilation° with ECOtronic TN-L° day-night-weekly programming - Exhaust via roof, type B or C ° - Exhaust through outer wall, type C ° Gas Warm Air Heater Type: UDSA055-4E Appliance category: B22P-C12-C32-C52-C62 Designation: DE Gas category: I2ELL Gas type: G20 natural gas Connection pressure: 20 mbar Nozzle pressure: 8.40 mbar Max. rated thermal load (Hs) QN: 66.04 kW Max. rated thermal load (Hi) QN: 59.50 kW Min. rated thermal load (Hs) QN: 33.02 kW Min. rated thermal load (Hi) QN: 29.75 kW Max. rated heat output: 54.74 kW Min. rated heat output: 26.92 kW Connection voltage: 230V 1N, 50Hz Air flow rate: 5830 m³/h Protection class: IP20 Pin No. 0461BN0677 More items – new and used – can be found in our shop! International shipping costs available on request!

Sąlyga: geras (naudotas), Reznor UDSA Gas Warm Air Heater Gas Warm Air Unit Type: UDSA050-4E Gas Appliance Category: BSP-C12-C32-C52-C62 Specification: DE Gusdpfewb Axrsx Abmek Gas Category: I2ELL Gas Type: G20 Natural Gas Connection Pressure: 20 mbar Nozzle Pressure: 7.90 mbar Max. Rated Heat Input (Hs) QN: 58.60 kW Max. Rated Heat Input (Hi) QN: 52.80 kW Min. Rated Heat Input (Hs) QN: Min. Rated Heat Input (Hi) QN: Max. Rated Heat Output: 48.58 kW Min. Rated Heat Output: Connection Voltage: 230V 1N, 50Hz Air Volume Flow: 5,180 m³/h Protection Class: IP20 Pin No. 0461BN0677 UDSA Gas Warm Air Heater – Efficient to the Core The most renowned unit from REZNOR is the UDSA gas warm air heater, providing uniform air distribution in industrial halls. This recirculating heater is easy to install, available in 14 output sizes from 7 to 97 kW, and consists of a heat exchanger, gas burner, and an exhaust fan. Combustion air can be drawn either from outside as standard or from the installation area. The REZNOR UDSA warm air heater ensures even air distribution within the heated hall. Its patented heat exchanger sets new standards in airflow and heat transfer, achieving an efficiency of over 92 percent. UDSA: Compact, revolutionary, and pioneering. With this generation of units, halls can be heated in a particularly economical way directly – that is, without central heating – using decentralised, modulating gas warm air heaters. REZNOR UDSA Gas Warm Air Heater. The Advantages: - Efficiency of more than 92% - Unit is also suitable for vertical installation - Low NOx emissions - Innovative combustion concept - Quiet operation - With CE system certification, design B or C - Compact design for easy installation - Uniform heat distribution - Supplied with vertical and horizontal air guide vanes as standard - Heat output modulation down to 50% - EC technology - ErP Ready These units are directly fired gas warm air heaters with fan-assisted atmospheric multi-gas burners. Installation of the gas warm air heater, as well as the gas and exhaust connections, must be carried out by an authorised installation company. The gas warm air heaters are suitable for: - Operation with natural gas or LPG - Recirculation operation - Inlet temperatures below 5°C with stainless steel heat exchanger* - One-stage or two-stage* heating mode, controlled by room thermostat and heating control switch - Ventilation° controlled via ECOtronic TN-L° with day-night-week programme - Flue gas exhaust via roof, design B or C ° - Flue gas exhaust through external wall, design C ° More items – new and used – available in our shop! International shipping costs on request!

Sąlyga: beveik kaip naujas (naudotas), Oro pagalvių pakavimo mašina Air Space 9000 Guodpfxswzal Ns Abmok Mašina gamina oro pripildytus užpildus iš plėvelės rankovės. Maitinimas: 230 V Svoris apie 100 kg.

Sąlyga: paruoštas naudoti (naudotas), Funkcionalumas: visiškai funkcionalus, galia: 3 kW (4,08 AG), Pramoninis sandarinimo oro tiekimas garo turbinoms, generatoriams, katilams, guolių korpusams ir kitiems viršslėgio sandarinimo sistemoms. Užtikrina stabilų, sausą, švarų oro barjerą, saugantį įrangą nuo dulkių, drėgmės ir atgalinių dujų. Oro srautas: 1 080 – 1 368 m³/val. Gujdpfxoxy Rg So Abmjk Bendras slėgis: 1 385 – 2 753 Pa Ventiliatoriaus greitis: 2 860 aps./min. Variklio galia: 3 kW Svoris (be variklio): 130 kg Tvirtinimas: bendras plieninis rėmas Elektros variklis (ABB) Galia: 3 kW Įtampa: 400 / 690 V Apsaugos klasė: IP55 Darbo režimas: S1 (nenutrūkstamas darbas) Aušinimas: TEFC Jutikliai: PTC termistoriai (apsauga nuo apvijų perkaitimo) Greitis: 2 860 aps./min. Ypatybės Tvirta cinkuoto plieno korpusas Daniški pramoniniai ventiliatoriai (JHM / Howden) Sumontuoti reguliuojami įsiurbimo sklendės Pilnai sukomplektuoti su ABB varikliais ir jungimo dėžėmis Labai gera mechaninė būklė – be įtrūkimų, be korozijos židinių Visi įrenginiai buvo veikiantys iki sustabdymo Tinka nenutrūkstamam 24/7 darbui elektrinėse Didmeninis pirkimas (visi 6 vnt.) → papildoma nuolaida

Sąlyga: naujas, Gamybos metai: 2019, vėsinimo galia: 102 kW (138,68 AG), bendras svoris: 1 750 kg, garantijos trukmė: 6 mėnesiai, bendras aukštis: 2 050 mm, bendras ilgis: 3 800 mm, bendras plotis: 1 600 mm, Stogo oro kondicionierius EMICON RTTL 362 TR KC 102 kW Guodpfxsx Eiauj Abmjk Vėsinimo galia: 102 kW Pagaminimo metai: 2019 Šaldymo kontūras: 1 vnt. Kompresoriai: 2 vnt. Copeland (scroll) Ventiliatorių skaičius: 1 vnt. Šaltnešis: R410A Papildomos funkcijos: Elektrinis šildymas Matmenys: 3,80 х 1,60 х 2,05 m Svoris: 1750 kg Būklė: Outlet, Naujas

Sąlyga: naudotas, Gamybos metai: 2017, Funkcionalumas: visiškai funkcionalus, Oro kiekis 6300 m³/h Oro greitis 1,94 m/s Izoliacija 50 mm Filtrai M5 ir F7 Ventiliatoriaus didžiausia galia 2840 kW Gjdpfxjx Hhh No Abmsuk Šildytuvas: Oro įėjimo / išėjimo temperatūra -12 / 22 °C Aušintuvas: Oro įėjimo / išėjimo temperatūra 32 / 20 °C Matmenys (I x P x A): 3900 x 1050 x 1050 mm

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L/W/H): 800 x 1170 x 2280 mm Weight: 500 kg Total power requirement: 1 kW Hot Air Furnace MARTINA 85 The MARTINA hot air furnaces offer an ideal solution for energy utilization in woodworking industrial and craft businesses. They have been developed for heating larger utility spaces such as workshops and workspaces in craft and industrial enterprises. These hot air systems require no extended heat-up phases and can quickly warm up joinery, carpentry, or other production facilities. Solid wood and its by-products—e.g., solid wood board offcuts, chips, sawdust, pellets, or briquettes—serve as fuel. The MARTINA hot air furnaces comply with EU Directive 98/37CE, Italian Presidential Decree No. 459 of July 24, 1996, and the safety provisions of Directive 89/392 CE. All hot air furnaces of the MARTINA series (15 – 30 – 55 – 85 – 120 – 180 – 240 – 350) meet both stages of required emission values according to the 1st BImSchV. - Automatic and continuous air operation - Thermal output: 85 kW - Thermal output (kcal): 73,000 - Fuel consumption: 19 kg/h - Air flow rate: 6,400 m³/h - Firebox depth: 840 mm - Loading door: 430 x 430 mm - Hot air fan: 0.98 kW / 230 V - Firebox negative pressure: 0.2–0.3 mbar - Flue draught at rated load: 0.18 mbar - Heatable room volume: approx. 1,600 m³ - Heat coverage area: approx. 300 m² - Space requirement: width 800 mm, depth 1170 mm, height 2200 mm - Weight: 500 kg Gujdpfjvz Hq Tox Abmok - Flue connection diameter: 200 mm - Recommended chimney diameter: 250 mm - Efficiency: 85–90% - Chimney draft pressure: 16 Pa - Flue gas temperature: 291°C - Hot air outlet port: 2 x Ø 220 mm - For further technical data, please refer to the attached data sheet The two pipe connections for the air outlet are located at the lower rear section of the furnace. A maximum of 20 meters of ducting per pipe connection is allowed for air distribution.

Sąlyga: naujas, ME-LINE – Air-cooled dehumidifiers are used for air drying in environments with up to 100% relative humidity (RH) at temperatures of +45°C and above. EU-LINE – Air-cooled dehumidifiers are designed for air drying with up to 100% relative humidity (RH) at temperatures ranging from -30°C to +40°C. Rust is the adversary of freshly blasted steel; high humidity combined with low steel temperatures creates ideal conditions for moisture condensation on the newly blasted surface. Condensation-induced rust is one of the main causes of premature coating failure. By reducing relative humidity, Proton dehumidifiers are engineered to create the optimum climatic conditions for blasting operations. Climatic conditions worldwide vary considerably – from cool and damp in Western Europe to hot and humid in the Middle East, and warm and humid in the Far East. Various dehumidification technologies can be employed in this process; certain technologies perform better in specific climate conditions than others. Every Proton dehumidifier is manufactured to the highest quality standards and features regional certification. The core of the dehumidifier is a highly efficient and robust metal silicate rotor. The rotor contains numerous air channels running parallel to the shaft, providing a large internal surface area for the adsorption of water vapor. Oversaturation does not affect the rotor. Therefore, the PROTON dehumidifier’s rotor can withstand extended storage in high humidity without any loss of capacity. PROTON dehumidifiers have been specially developed for corrosion protection in conjunction with sandblasting and coating work, to preserve materials and avoid moisture-related issues. They meet the following criteria: • Available in sizes ranging from 1,000 m³/h to 18,000 m³/h dry air. • Available in pre-cooled and post-cooled versions for warm climates. • Robust construction with steel frame, lifting lugs, etc. • Key components are easily maintained and replaced. • Large air inlet grilles and filters. • Can be installed in containers for protection. • Adjustable dehumidification performance and air outlet temperature in 4 levels. • Suitable for outdoor and indoor use. • Dry air pressure up to 1200 Pa. Gusdpfskw Ukujx Abmjk Technical specifications: Dehumidifiers range from 1,000 m³/h to 18,000 m³/h. PROTON dehumidifiers reduce relative humidity (RH) from 90% to 10–15%. The units can remove up to 100 liters of water per hour.

Sąlyga: visiškai atnaujintas (naudotas), Gamybos metai: 2000, veikimo valandos: 3 200 h, Funkcionalumas: visiškai funkcionalus, kuras: dyzelinas, Mašina u izvanrednom stanju sa malo radnih sati, opciono dostupan mobilni bunker-transporter (onaj sa slike) uz doplatu. Nova čistilica za transportnu traku. Gsdpfx Abjvy A Ursmeuk

Sąlyga: beveik kaip naujas (naudotas), Funkcionalumas: visiškai funkcionalus, galia: 166 kW (225,70 AG), darbinis slėgis: 10 juosta, aušinimo tipas: oras, Atlas Copco GA160, wtryskowa sprężarka śrubowa, 166 kW, 10 bar, 2006 r. Urządzenie w bardzo dobrym stanie technicznym i wizualnym. Sterownik Elektronikon® pracuje poprawnie, start i stop maszyny odbywa się prawidłowo, brak widocznych wycieków oleju. Wydajność sprężonego powietrza przy 10 barach wynosi ok. 27–30 m³/min. Idealne do zastosowań: - Zakłady produkcyjne - Przemysł drzewny (suszenie, peleciarki, linie pneumatyczne) - Centra transportowo-logistyczne - Dowolne instalacje przemysłowe wymagające dużej wydajności powietrza (>160 kW) Dane techniczne: Moc silnika: 166 kW Gedpfx Ajxy Nq Nobmjuk Ciśnienie robocze: 10 bar Wydajność: ~27–30 m³/min Obroty: 1488 obr./min. Zasilanie: 400 V, 50 Hz Typ sprężarki: śrubowa, wtrysk oleju Chłodzenie: powietrzem Sterownik: Elektronikon® Stan: bardzo dobry; suchy, brak widocznych wycieków oleju Stan wizualny (na zdjęciach): - Maszyna zadbana, czysta - Panel sterowania sprawny, uruchamia się poprawnie - Brak korozji na głównych panelach obudowy - Rury i połączenia w bardzo dobrym stanie technicznym WYPOSAŻENIE W CENIE: ✔ Pełna obudowa dźwiękoszczelna ✔ Sterownik Elektronikon® ✔ Odprowadzenie kondensatu ✔ Zamontowana instalacja wylotu powietrza ✔ Solidne, czyste osłony obudowy ✔ W pełni sprawny panel operatorski

Sąlyga: naujas, Gamybos metai: 2022, vėsinimo galia: 106,2 kW (144,39 AG), bendras svoris: 1 780 kg, garantijos trukmė: 6 mėnesiai, bendras aukštis: 2 410 mm, bendras ilgis: 6 100 mm, bendras plotis: 2 250 mm, Stogo oro kondicionierius CLIMAVENETA WSM2-T 0354 106,2 kW Vėsinimo galia: 106,2 kW / 30,2 tonos Pagaminimo metai: 2022 Pasirinkimai: Oro filtras, Wika oro srauto jutiklis, 2 vnt. Belimo sklendžių pavaros. Šaltnešio kontūras: 2 vnt. Šilumokaitis: Varis / Aliuminis Kondensatorius: Varis / Aliuminis Kompresoriai: 4 vnt. Copeland scroll ZP104KCE-TFD-477 (scroll) Ventiliatorių skaičius: 2 vnt. + 4 vnt. (centrifuginiai, EC ventiliatoriai) Šaltnešis: R410A Matmenys: 6,1 х 2,25 х 2,41 m Gjdpox Eh S Aefx Abmsuk Svoris: 1780 kg Darbo valandos: 0/0/0/0 val. Būklė: Išpardavimas, Naujas

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L x W x H): 720 x 1000 x 1900 mm Weight: 300 kg Total Power Requirement: 1.2 kW Hot Air Furnace MARTINA 55 The MARTINA hot air furnaces are an ideal solution for energy recovery in wood-processing industrial and craft businesses. They are designed to heat large areas, such as workshops and working spaces in trade and industrial operations. These hot air systems require no lengthy warm-up phases and can heat up workshop halls of joineries or carpentries, as well as other production facilities, in a very short time. Solid wood and its by-products (e.g. offcuts from solid wood panels, chips, sawdust, pellets, or briquettes) serve as fuel materials. The MARTINA hot air furnaces comply with EU Directive 98/37CE and Italian Presidential Decree No. 459 dated July 24, 1996, as well as the safety directive of 89/392 CE. All MARTINA series hot air furnaces (models 15 – 30 – 55 – 85 – 120 – 180 – 240 – 350) meet both emission stages according to the 1st German Federal Immission Control Ordinance (BImSchV). - Automatic and continuous air operation - Thermal output: 49.9 kW - Thermal output Kcal: 43,000 - Fuel consumption: 15 kg/h Gusdpfx Abjvz Hq Hemek - Air output: 4,900 m3/h - Combustion chamber depth: 650 mm - Loading door: 370 x 350 mm - Hot air blower: 1.12 kW / 230 V - Firebox negative pressure: 0.2–0.3 mbar - Draft requirement at nominal output: 0.18 mbar - Heatable volume: approx. 1,000 m3 - Heatable area: approx. 220 m2 - Space requirement: Width 720 mm, Depth 1,000 mm, Height 1,900 mm - Weight: 300 kg - Flue pipe diameter (collar): 160 mm - Chimney diameter (recommended): 200 mm - Efficiency: 85–90% - Chimney discharge pressure: 13 PA - Flue gas temperature: 290°C - Hot air outlet spigots: 2 x Ø 200 mm - For additional technical data, please refer to the attached data sheet The two pipes for outgoing hot air are located at the lower part of the rear side of the furnace. A maximum of 20 meters of ducting per spigot is permitted for air distribution.

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L/W/H): 1700 x 2000 x 2550 mm Weight: 1400 kg Total power requirement: 4.5 kW Hot Air Furnace MARTINA 350 The MARTINA hot air furnaces are an ideal solution for energy utilization in wood-processing industrial and craft businesses. They have been developed for heating large utility areas, such as workshops and working spaces of trade and industrial enterprises. These hot air systems require no long heat-up phases and heat up woodworking shops, carpentries, and other production areas within a very short time. Gedevz Hqyspfx Abmouk The furnaces can use solid wood and its by-products as fuel, e.g. solid wood panel residues, chips, sawdust, pellets, or briquettes. The MARTINA hot air furnaces comply with EU Directive 98/37CE, Italian Presidential Decree No. 459 dated July 24, 1996, and safety guideline Directive 89/392 CE. All hot air furnaces of the MARTINA series (15 – 30 – 55 – 85 – 120 – 180 – 240 – 350) meet both stages of emission limits stipulated by the 1st BImSchV. - Automatic and continuous air operation - Thermal output: 390 kW - Thermal output (Kcal): 335,000 - Fuel consumption: 85 kg/h - Air output: 20,000 m³/h - Combustion chamber depth: 1400 mm - Feed door: 500 x 700 mm - Hot air blower: 4.48 kW - Firebox negative pressure: 0.2–0.3 mbar - Flue draft requirement at nominal output: 0.18 mbar - Heatable room volume: approx. 7,500 m³ - Heatable area: approx. 1,600 m² - Space requirement: width 1700 mm, depth 2000 mm, height 2550 mm - Weight: 1400 kg - Flue pipe diameter (connection): 300 mm - Chimney diameter (reference value): 350 mm - Efficiency: 85–90% - Chimney draft: 11.5 Pa - Flue gas temperature: 289°C - Hot air discharge nozzles: 2 x Ø 450 mm - For additional data, please refer to the data sheet. The two pipe fittings for outgoing hot air are located at the rear of the furnace near the bottom. For each pipe fitting, a maximum pipe length of 20 meters is allowed for air distribution. Longer lengths are optionally available upon arrangement with the manufacturer. Please contact us for more details.

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L/W/H): 600 x 800 x 1900 mm Gedpfxjvz Hqtj Abmjuk Weight: 230 kg Total power requirement: 0.5 kW Hot Air Furnace MARTINA 30-15 The MARTINA hot air furnaces are an ideal solution for energy utilization in woodworking industrial and craft businesses. They are designed for heating larger functional areas, such as workshops and workspaces in craft and industrial facilities. These hot air systems require no long heat-up phases and warm up the workshop or production hall—such as those in carpentry, joinery, or other manufacturing environments—in a very short time. Suitable fuels include solid wood and its by-products, e.g. solid wood board offcuts, shavings, sawdust, pellets, or briquettes. The MARTINA hot air furnaces comply with EU Directive 98/37CE, Italian Presidential Decree No. 459 dated 24 July 1996, and the safety directive of installation 89/392 CE. All MARTINA series hot air furnaces (models 15, 30, 55, 85, 120, 180, 240, 350) meet both emission stages required by the 1st BImSchV (Federal Emission Control Ordinance). - Automatic and continuous air operation - Thermal output: 14.8 kW - Thermal output: 12,720 Kcal - Fuel consumption: 4.5 kg/h - Air flow rate: 2,400 m³/h - Combustion chamber depth: 580 mm - Loading door: 330 x 330 mm - Hot air blower: 0.49 kW / 230 V - Firebox negative pressure: 0.2–0.3 mbar - Draft requirement at rated output: 0.18 mbar - Heatable room volume: approx. 300 m³ - Heatable area: approx. 60 m² - Space requirement: width 600 mm, depth 800 mm, height 1900 mm - Weight: 230 kg - Flue pipe diameter (connector): 160 mm - Recommended chimney diameter: 200 mm - Efficiency: 85–90% - Chimney pressure: 11 Pa - Flue gas temperature: 286°C - Hot air outlet connectors: 2 x Ø 200 mm - For further specifications, please refer to the attached data sheet The two duct connectors for warm air outlet are located at the lower rear side of the unit. A maximum pipe length of 20 meters per connector is permitted for air distribution.

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L/W/H): 600 x 800 x 1900 mm Weight: 230 kg Total power requirement: 0.5 kW Hot Air Furnace MARTINA 30 The MARTINA hot air furnaces offer an ideal solution for energy recovery in woodworking industrial and craft businesses. They are designed to heat larger usable spaces such as production halls and work areas in trade and industrial facilities. These hot air systems require no lengthy heat-up phases and can quickly warm up carpentry or joinery workshops as well as other manufacturing sites. Fuel types include solid wood and its by-products, such as remnants of solid wood boards, chips, sawdust, pellets, or briquettes. MARTINA hot air furnaces comply with EU Directive 98/37/CE, Italian Presidential Decree No. 459 of July 24, 1996, and the safety directive of Equipment 89/392/CE. All MARTINA series hot air furnaces (15 – 30 – 55 – 85 – 120 – 180 – 240 – 350) meet both emission threshold stages required by the 1st German Federal Immission Control Ordinance (BImSchV). - Automatic operation and continuous air mode - Thermal output: 29.8 kW - Thermal output (Kcal): 25,700 - Fuel consumption: 9 kg/h - Air output: 2,400 m³/h - Combustion chamber depth: 580 mm - Loading door: 330 x 330 mm - Hot air blower: 0.49 kW / 230 V - Firebox underpressure: 0.2–0.3 mbar - Draft requirement at nominal output: 0.18 mbar - Heatable volume: approx. 600 m³ - Heatable surface area: approx. 120 m² - Footprint: Width 600 mm, Depth 800 mm, Height 1900 mm - Weight: 230 kg - Flue outlet diameter (collar): 160 mm - Chimney diameter (reference value): 200 mm - Efficiency: 85–90% - Chimney draft: 11 Pa - Exhaust gas temperature: 286 °C - Hot air outlet connections: 2 x Ø 200 mm Gjdpfx Abevz Hqmjmeuk - For further technical data, please refer to the attached data sheet The two pipe collars for the outgoing hot air are located on the rear side of the furnace in the lower section. A maximum pipe length of 20 metres is permitted per collar for air distribution.

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L x W x H): 1300 x 1700 x 2550 mm Weight: 1200 kg Total connected load: 2 kW Hot Air Furnace MARTINA 240 The MARTINA hot air furnaces offer an ideal solution for energy utilization in wood-processing industrial and craft businesses. They are designed for heating large usable spaces such as workshops and production areas in craft or industrial enterprises. These hot air systems do not require long heating-up phases and are capable of rapidly warming up joinery and carpentry workshops or other production facilities. The units can burn solid wood and its byproducts, e.g. offcuts from solid wood panels, chips, sawdust, pellets, or briquettes. MARTINA hot air furnaces comply with EU Directive 98/37/EC, Italian Presidential Decree No. 459 of 24 July 1996, and safety guideline 89/392/EEC. All hot air furnaces of the MARTINA series 15 – 30 – 55 – 85 – 120 – 180 – 240 – 350 fulfill both stages of the emission values required by the 1st BImSchV. - Automatic and continuous air operation - Thermal output: 233 kW - Thermal output (kcal): 199,000 - Fuel consumption: 50 kg/h - Airflow rate: 18,000 m³/h - Combustion chamber depth: 1200 mm - Loading door: 460 x 600 mm - Hot air fan: 1.96 kW / 230 V - Firebox negative pressure: 0.2-0.3 mbar - Nominal output draft requirement: 0.18 mbar - Heatable volume: approx. 4,500 m³ - Heatable area: approx. 900 m² - Space required: width 1300 mm, depth 1700 mm, height 2550 mm - Weight: 1200 kg - Flue pipe diameter (connection): 250 mm - Recommended chimney diameter: 300 mm - Efficiency: 85–90 % - Chimney fan pressure: 16 Pa - Flue gas temperature: 290 °C Gusdpfxjvz Hqgs Abmek - Hot air outlet connections: 2 x Ø 450 mm - Further data available in the attached data sheet The two duct connections for outgoing hot air are located on the lower rear side of the unit. A maximum of 20 meters of duct per outlet is allowed for air distribution.

Sąlyga: naujas, Gamybos metai: 2025, Dimensions (L x W x H): 800 x 1170 x 2300 mm Weight: 650 kg Total power requirement: 1.05 kW Warm Air Furnace MARTINA 120 The MARTINA warm air furnaces provide an ideal solution for energy utilization in woodworking industrial and craft businesses. They have been developed for heating larger areas, such as workshops and production halls in both craft and industrial operations. These warm air systems require no lengthy preheating times and are capable of warming up joinery or carpentry workshops and other production facilities in a very short period. The furnace can be fueled with solid wood and its by-products, e.g. offcuts from solid wood panels, chips, sawdust, pellets, or briquettes. The MARTINA warm air furnaces comply with EU Directive 98/37/EC, Italian Presidential Decree No. 459 of July 24, 1996, and the safety guideline of Directive 89/392/EEC. All warm air furnaces in the MARTINA series (15 – 30 – 55 – 85 – 120 – 180 – 240 – 350) fulfill both stages of the emission limits required by the 1st Federal Immission Control Ordinance (BImSchV). - Automatic and continuous air operation - Thermal output: 145 kW - Thermal output: 125,000 kcal - Fuel consumption: 30 kg/h - Air performance: 9,000 m³/h - Combustion chamber depth: 950 mm - Loading door: 460 x 440 mm - Warm air blower: 1.05 kW / 230 V - Combustion chamber negative pressure: 0.2–0.3 mbar - Flue draught at nominal load: 0.18 mbar - Heatable room volume: approx. 2,500 m³ - Heatable area: approx. 500 m² - Required space: Width 800 mm, Depth 1170 mm, Height 2300 mm - Weight: 650 kg - Flue pipe diameter (connector): 200 mm Guodpfx Aovz Hhxobmek - Chimney diameter (recommendation): 250 mm - Efficiency: 85–90% - Chimney draft: 16 Pa - Exhaust gas temperature: 287°C - Warm air outlet nozzles: 2 x Ø 220 mm - For further data, please refer to the enclosed data sheet The two pipe connectors for outgoing warm air are located at the rear bottom side of the furnace. A maximum pipe length of 20 meters per nozzle is permitted for air distribution.