Vertikalios vidinio prabraukimo staklės

Karl Klink RISH 16.1000.630

Būklė: geras (naudotas), Gamybos metai: 1998, Press force: 315.00 t Stroke: 500 mm Throat depth: 425 mm Fgjdpfx Aev Rwu Uen Heh Daylight (Stroke up): 1,000 mm Table surface: 1,200 x 815 mm Table height above floor: 800 mm Ram surface: 1,100 x 700 mm Downward speed: 48 mm/s Upward speed: 330 mm/s Working speed: 19 mm/s Oil capacity: 1,600 l Power requirement: 82.0 kW Weight: 23.00 t Overall dimensions (W x D x H): 2.4 x 2.8 x 4.0 m Permitted for manual loading according to CE regulations. Equipped with oil-hydraulic drive, pressure-, time- and stroke-dependent control, front light barrier (Sick), two-hand operation.

Būklė: labai geros būklės (naudotas), Gamybos metai: 2006, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 7213, Country of manufacture: Switzerland Net weight: approx. 2550 kg Customs tariff number: 8458.11 20 Dimensions: 2000x1260x1950 mm TECHNICAL SPECIFICATIONS 10-axis machine – standard 10 axes, 6 spindles: Axes and spindle designation - 1 sliding headstock: Z1, S1 - 2 independent vertical tool posts: X1Y1, S6 – X2Y2, S2 - 1 unit with 4 rotary spindles: X3Z3, S3 - 1 independent sub-spindle: Y4Z4, S4 - 1 independent rotating axis for back-working: X4, S5 Bar feeder position: on operator's right Machine center height: 1100 mm Main spindle travel: max. 255 mm Fjdpjw T Tcwofx An Hegh Bar capacity: 1 to 16 mm Spindle speed: 12,000 rpm Spindle feed rate: max. 20 m/min Bar capacity, min./max.: 13 mm / 16 mm Max. part length: - guide bush machining: 180 mm - collet machining: 30 mm Sub-spindle speed: 12,000 rpm Main spindle drive power: 2.2 kW (continuous), 3.7 kW (intermittent) Sub-spindle drive power: 1.5 kW (continuous), 2.2 kW (intermittent) Clamping collet, type: F20 (no. 76-201) Guide bush: fixed / rotary Collet for guide bush, type: Meister 605 Number of side tool holders, combined - fixed: 2 x 5 - rotary: 3 + 3 Number of front tool holders, combined - fixed: 4 - rotary: 3 Number of rear tool holders, combined - fixed: 3 + 3 - rotary: 3+3 Tool section: 12x12 mm Standard rotary tool holder: ESX 20 Bar feeder: yes Parts catcher: yes All technical data subject to change without notice, errors and omissions excepted.

Gamybos metai: 1999, būklė: beveik kaip naujas (naudotas), Funkcionalumas: visiškai funkcionalus, Manufacturer: Arthur Klink Year of manufacture: 1999 Type: Horizontal Broaching Machine Model: RIW 10x1600x400 Weight: 2,700 kg General / Technical Data: Horizontal hydraulic internal broaching machine in near-new condition, equipped with a tool lift system, ideal for the use of flat broaching tools. Broaching stroke: 1,600 mm Tensile force: 10,000 kg (100 kN) Tool holder in drawbridge: Ø 85 mm cylindrical Through-hole in clamping table: Ø 100 mm Workpiece diameter: max. 400 mm (limited by the machine body of the tool tray) Cutting speed: hydraulically infinitely variable from 1.0 m/min to 9 m/min Return speed: hydraulically infinitely variable from 1 m/min to 24 m/min Machine dimensions (W x D x H): approx. 6,400 mm x 1,450 mm x 1,600 mm (without working area) Power supply: 400 Volt, 50 Hz Connected load: 9 kW Equipment: • The machine has an electric control for the broaching stroke movement with both manual and automatic operation. Fedpfx Asr A Hcben Hsgh • Integrated coolant/lubrication system • Tool lift system for flat broaching tools (no automatic feed) • The broaching slide with pull head holder is equipped with flat guides on both sides Accessories: • 1 universal pull head for flat shanks from 3 mm up to max. 25 mm width and a maximum tensile force of 10 kN (10,000 kg) • Complete machine documentation, including CE declaration of conformity Remarks: The machine is ideal for manufacturing keyway slots. Thanks to its robust machine bed and the integrated tool lift system, it is especially well-suited for quick and easy use of flat broaching tools. The machine has had very limited use and is in near-new condition. The machine is available for inspection at our warehouse and can be demonstrated under power. Our direct contact details and further information about the machine can be found in the attached PDF document.

Būklė: labai geros būklės (naudotas), Gamybos metai: 2020, X ašies eiga: 8 000 mm, Y ašies eiga: 1 300 mm, Z ašies eigos atstumas: 2 500 mm, greitas poslinkis X ašimi: 35 000 m/min, greitas poslinkis Y ašis: 40 000 m/min, greitasis eiga Z ašyje: 40 000 m/min, bendras plotis: 5 800 mm, bendras aukštis: 4 500 mm, bendras ilgis: 13 500 mm, stalo ilgis: 10 000 mm, stalo plotis: 1 250 mm, Travelling column – high performance, precision, and machining capability Linear RAM guide combined with hydrostatic HDS guide ACD2 milling head with 5,000 rpm and 1,400 Nm torque Aitek ATC chain magazine with 60 positions, L = 400 and Ø 250, max. 35 kg Filtration with through-spindle coolant at 15 bar Chip conveyor BLUM 3D measuring probe Wide bed, linearly guided on the X-axis, traverse path W = 930 mm Rotary table drive pre-installed in electrical cabinet X-Axis: 8,000 mm Y-Axis: 1,300 mm Z-Axis: 2,500 mm Table length: 10,000 mm Table width: 1,250 mm Spindle power: 40 kW Spindle speed: 5,000 rpm Tool holder: ISO 40/BT/MK X-axis feedrate: 35,000 mm/min Y-axis feedrate: 40,000 mm/min Z-axis feedrate: 40,000 mm/min Milling head auto-indexing: 0.001 x 0.001 deg Operating hours: 3,800 h Length: 13,500 mm Fsdpeyr Dmdofx An Hegh Width: 5,800 mm Height: 4,500 mm Weight: 45,000 kg Please note: The information on this page was provided to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Consequently, these details do not constitute representation or contractual terms. We recommend verifying all critical details.

Gamybos metai: 1995, būklė: naudotas, mašinos/transporto priemonės numeris: 18891, Tractive force: 10 tons. Stroke: 1000 mm. 3 ejector stations. With chip conveyor and platform for above-ground installation, including safety door. Fsdebrcmkepfx An Hjgh

Būklė: beveik kaip naujas (naudotas), Gamybos metai: 2021, Offered is a double-spindle pick-up turning machine EMAG VSC 500 DUO. The machine is equipped with 2 independent work spindles and 2 EMAG turrets. The machine can be used for machining either 2 identical parts in the same operation or a single part in two consecutive operations. Depending on requirements, the machine can be equipped with additional peripherals (chip conveyor, coolant system, external automation, etc.). CONTROL Siemens 840 Dsl TECHNICAL DATA Workpiece diameter: max. 440 mm Workpiece height: max. 250 mm Chuck diameter: 450 mm Swing diameter: 550 mm X-axis travel: 925 mm Z-axis travel: 400 mm Fgedpjt Du Tdjfx An Heh TOOL CARRIER 2x EMAG disc turrets, 12x CDI 68, with live tooling Price, delivery time and machine configuration upon request.

Būklė: naudotas, Gamybos metai: 1999, Spaudimas 130 t Lenkimo ilgis 3550 mm Stovų tarpas 3060 mm Įmontavimo aukštis 510 mm Valdymas Cybelec DNC 80 Įkirpimo gylis 320 mm Fodpfxsvxwqfe An Hegh Eiga 250 mm Darbo aukštis 900 mm Staklių svoris apie 12000 kg Užimama vieta apie 4,05x2,1x2,85 m Valdymo sistema Cybelec DNC 80 Y1;Y2;X;R ašys Matricos poslinkis su rankenėle 4 atraminiai pirštai Hidraulinis štampo tvirtinimas WILA Hidraulinis matricos tvirtinimas Amada sistema 2 atraminės svirtys Saugus valdymas dviem rankomis / pedalu Įvairūs štampai ir matricos

Būklė: naudotas, Gamybos metai: 1972, max. pulling force: 10 t max. stroke: 1,250 mm max. cutting speed: 10 m/min max. return speed: 25 m/min broaching stations: 3 passage width: 470 mm distance between broaching stations: 125 mm Fodpfx Anecdtnhe Hsgh table: 400 x 400 mm special features: chip removal via permanent magnet chip conveyor 1 hydraulic system, 1 working platform, electric-hydraulic shank and end piece holder lock, automatic loading device

Būklė: geras (naudotas), X ašies eiga: 12 000 mm, Y ašies eiga: 7 300 mm, Z ašies eigos atstumas: 3 000 mm, bendras ilgis: 30 000 mm, stalo ilgis: 12 000 mm, stalo plotis: 4 730 mm, bendras plotis: 12 000 mm, bendras aukštis: 10 475 mm, stalo apkrova: 250 000 kg, bendras svoris: 400 000 kg, Portal Milling Machine WALDRICH SIEGEN - PF-F-150 Manufacturer: Waldrich-Siegen - Type: PF-F-150(1)-530/400 X-Axis: 12,000 mm Y-Axis: 7,300 mm Z-Axis: 3,000 mm W-Axis: 4,000 mm Distance between uprights: 5,000 mm Table width: 4,730 mm Table length: 12,000 mm Table load capacity: 19 t/m – approx. 250 t total Table traverse speed: 10,000 mm/min W-Axis feed: 3,000 mm/min T-Axis feed: 6,000 mm/min Transversely movable milling head Vertically adjustable cross beam Horizontal hydrostatic spindle ram Milling spindle diameter: 560 mm Tool holder: ISO 60 C-Axis feed: 5,000 mm/min Milling motor: 90 kW Spindle speed: 2,500 rpm Z-Axis travel: 3,000 mm Z-Axis feed: 2,000 mm/min Küma angle head WF2 – 90 kW – 450 rpm Küma universal milling head UB1D – 60 kW – 2,400 rpm Küma fixed head GB1D – 90 kW – 2,400 rpm Küma angle head WF1 Power supply: 3 × 400 V / 50 Hz Power requirement: 600 kVA / 630 Amps Coolant system: 4,000 liters – Coolant through the spindle 20 / 40 bar Fgjdpfxoytrxkj An Heh Machine overhauled in 2004 by Schiess Bed – Table Assembly: • Renewal of slideways • Regrinding of guideways • Renewal of table drive • Direct linear measuring system • Hydrostatic guideways Portal and Cross Beam: • Modification of adjustment spindle • Trapezoidal spindle replaced by ball screw • Direct linear measuring system • New drive motors to increase milling axes traverse speeds • New milling slide with hydrostatic guideways Electrical System: • Completely new control cabinet • Complete new wiring • Siemens Sinumerik 840D CNC – 6 axes Equipment: • Completely new Raumag-Janich protective covers • Completely new double chip conveyor • Large tool package • Extensive clamping devices Machine under power in Europe Immediately available Controlled axes: X / Y / Z / W / C / B Overall height: 10,475 mm Overall width: 11,934 mm Overall length: 30,000 mm Total weight: approx. 400,000 kg Completely overhauled in 2004 for EUR 2,200,000! This CNC portal milling machine from Waldrich was used in the energy sector for machining steam turbine casings. Please note: The information on this page has been provided to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. As such, they do not constitute representations or warranty terms. We recommend verifying all crucial details.

Gamybos metai: 1980, būklė: geras (naudotas), Bandwidth: max. 1,650 mm Band thickness: max. 3 mm Knife shaft diameter: 165 mm Speed: max. 150 m/min Fgjdpegrylqjfx An Heh