Mandrelio vamzdžių lenkimo staklės

Jutec 6000D

Būklė: naujas, Gamybos metai: 2025, mašinos/transporto priemonės numeris: 1018, THE POWERFUL BENDING MACHINE FOR WORKSHOP AND ON-SITE ASSEMBLY This compact and mobile bending machine enables precise and repeatable bending up to an outside diameter of 60 mm, both stationary and directly at the installation site. A powerful three-phase motor and a precision gearbox provide robust drive power. Position detection directly on the bending axis ensures optimal bending accuracy. The bending angle is set quickly and easily via a user-friendly, menu-guided touchscreen interface, which guarantees even more intuitive operation. For more complex bending tasks, up to 100 bending programs can be stored, each with angle sequences of up to 8 bends per geometry. The multifunction control allows variable adjustment of the bending speed for forward and return motions, and a parametrizable overbend function compensates for material spring-back. Thanks to four selectable material curves, the material is automatically overbent to the required angle, ensuring a precise bending result. The “stationary pipe, rotating tool” principle ensures a minimal footprint during bending operations. For thin-walled tubes, sliding shoes are used to achieve wrinkle-free bends and to bend arcs with minimal deformation in materials such as stainless steel and copper pipes. With the PB20 profile bending attachment, flat, square, and round bars can be bent effortlessly. The KBV small-radius bending attachment enables extremely tight bending radii. POSSIBLE APPLICATION AREAS: • Plant engineering • Hydraulic piping • Serpentine/Meander bending • Prototype construction • Plumbing and heating installation TECHNICAL DATA: Bending capacity 6000SB: Ø 6 to 50 x 4 mm, single-phase 230 V Bending capacity 6000D: Ø 6 to 60 x 4 mm Bending capacity 6000DS: Ø 6 to 60 x 5 mm, three-phase 400 V Rsdpfxong Ax Sj Af Tjcf Bending capacity 6000D: Ø 6 to 60 x 4 mm, three-phase 400 V • Bending radius min/max: 36 mm / 280 mm • Optional large bending radii up to 500 mm • Multifunctional machine control with bending angle adjustment (0.1° increments) • Maximum bending angle: 240° • 40 mm hex shaft for quick tool changes • Safety foot switch with emergency stop • Weight: 110 kg OPTIONAL ACCESSORIES: • Profile bender PB20 – for bending flat and square bar up to max. 100 x 10 mm, round bar up to max. 20 mm • Roll bender RB43 – the RB43 mounts to the hex shaft on the bending axis. Switching to continuous bending mode transforms the system into a drive unit. • Small-radius bending attachment KBV • Special tooling according to specifications OUR ON-SITE SERVICE FOR YOU: • Welcome to test production at our facility in the demo room • Consultation and information meeting at your premises • Consulting and financing/leasing arrangements • Trade-in of your current machine • Service contracts, maintenance at your location

Būklė: naujas, Gamybos metai: 2025, THE PRACTICAL HAND PIPE BENDING DEVICE: The compact, mobile design enables precise and repeatable bending in a bench vice. The drive is operated via a screw-in handle. A lockable adjustment ring ensures repeatable bending accuracy. The interchangeable tools can be replaced with minimal effort. The 'stationary pipe and rotating tool' principle allows bending in the smallest possible space. For thin-walled pipes, sliding shoes are used for crease-free bending, allowing bends in stainless steel or copper pipes with minimal deformation. The optional version with a hexagonal drive enables use in a vice as well as the possibility to use the drive power of the bending systems 3000 and 6000. The KBV can simply be mounted onto the bending shaft of the machine. POSSIBLE APPLICATIONS: • Hydraulic pipework • Prototype construction • Plumbing and heating installation TECHNICAL DATA: • Bending capacity Ø 6 to 18 mm • Manual bending angle limiter • Maximum bending result up to 180º Redpong Amkofx Af Tjcf OPTIONAL ACCESSORIES: • KBV with hexagonal drive for bending on models 3000 or 6000 • Tool case • Length stop OUR SERVICE FOR YOU ON SITE: • Welcome to test production at our in-house demo room • Consulting and information meetings at your site • Consultation and processing of leasing/financing purchase via JUTEC • Trade-in of your current machine • Service contracts, on-site maintenance

Būklė: naudotas, Čia siūlome JUTEC 6000D vamzdžių lenkimo stakles. Redpfxoxz Rz Eo Af Tscf Duomenis rasite pridėtame pasiūlyme. Jei turite klausimų, susisiekite su mumis.

Būklė: visiškai atnaujintas (naudotas), Gamybos metai: 1996, Funkcionalumas: visiškai funkcionalus, gręžimo pajėgumas: 40 mm, plunksnos brūkšnys: 200 mm, quill skersmuo: 80 mm, Dimensions and Travel Paths Tool Holder: SK 40 Table Dimensions: mm 4000 x 800 Number of T-slots: 6 T-slot spacing: mm 140 Distance, spindle lower edge min.: mm 140 table upper edge max.: mm 740 Drilling radius min.: mm 540 max.: mm 1590 U-axis travel: mm 2600 Y-axis travel: mm 1050 Quill stroke (Z-axis): mm 200 Column stroke (W-axis): mm 400 Machining Values Drilling capacity, solid material St 60: mm 40 GG 22: mm 50 Thread cutting St 60: M 36 GG 22: M 42 Main Spindle Drive AC Motor, frequency controlled kW 5.5 at 100 % duty cycle Speed range: rpm 15 - 2800 Torque: Nm max. 250 Constant from: rpm 15 – 200 Feed Drives X-axis - AC Servo Motor: kW 0.25 Y-axis - AC Servo Motor: kW 0.25 Z-axis - AC Servo Motor: kW 4.50 W-axis - AC Servo Motor: kW 2.50 U-axis - AC Servo Motor: kW 2.50 Rapid traverse speeds (X/Y/Z): m/min 7.5 / 7.5 / 5 Rapid traverse speeds (U/W): m/min 7.5 / 3 Feed rates, stepless: mm/min 5 - 2000 Feed force: N 12000 Accuracy Positioning accuracy X, Y axis on 1200 mm: mm ± 0.075 Repeatability X, Y axis: mm ± 0.03 Positioning accuracy Z-axis: mm ± 0.05 Repeatability Z-axis: mm ± 0.03 Positioning accuracy W-axis: mm ± 0.05 Repeatability W-axis: mm ± 0.03 Electrical Data Operating voltage / frequency: V / Hz 400 / 50 Control voltage: V 24 Rodpfx Ajv If T Tjf Tjcf Total connected load: kVA 13.0 CNC Control Axes: 5 (X,Y,Z,W,U), expandable Display: TFT flat panel, backlit, clearly visible from all sides Position information: Cartesian or polar, measurements absolute or incremental Unit of measure: mm or inch, or degrees Interpolation: 2 axes (X, Y) Technology database: tool management, tool suggestions by machining process, material-dependent cutting data recommendations Tool management: up to 500 tools Subprogram technique: yes Machining cycles: cycles for centering, drilling, tapping, reaming, countersinking, and boring; freely programmable cycle for special tools; dwell time possible in every cycle Chip breaking/chip removal: possible in drilling cycle Drilling patterns: linear, circular, matrix Basic software: conversational programming, 38 zero point shifts, rotating and mirroring, teach-in for X, Y, Z, program restart with selectable entry point Zero point determination: cycles for zero point determination by manually probing the workpiece for: - arbitrarily clamped rectangular parts - arbitrarily clamped round parts - alignment of cast and flame-cut parts - angle position detection for round parts by probing reference edges/surfaces Data interfaces: USB interface Coating (Refinishing) Standard painting, two-component textured paint Machine upper part: light grey RAL 7035 Machine base: signal blue RAL 5005 Documentation Operating and programming manual Electrical schematic Spare parts drawings Test report for mechanics, electrics and safety device

Būklė: naujas, Gamybos metai: 2025, Funkcionalumas: visiškai funkcionalus, bendras aukštis: 5 600 mm, bendras ilgis: 11 200 mm, bendras plotis: 5 100 mm, įvesties srovės tipas: trifazis, garantijos trukmė: 24 mėnesiai, vidinis aukštis: 4 970 mm, vidinis ilgis: 11 000 mm, temperatūra: 80 °C, vidinis plotis: 5 000 mm, oro poreikis: 52 000 m³/val, įėjimo įtampa: 380 V, šildymo galia: 250 kW (339,91 AG), galia: 45 kW (61,18 AG), kuras: suskystintos naftos dujos (LPG), įėjimo dažnis: 50 Hz, energijos suvartojimas: 45 kWh, izoliacijos storis: 50 mm, nominali galia: 250 kW (339,91 AG), plieno lakšto storis (maks.): 2 mm, Įranga: apšvietimas, * Air Treatment Unit: The air treatment unit is a recirculation system that supplies the cabin with filtered fresh air and expels used air during the painting process. It heats the air to 60°C, mixes 10% fresh air with recirculated air via an automatic multi-damper system, and reheats the air before it is fed back into the cabin. Air is heated using a burner and heat exchanger, both made from high-grade 304 stainless steel and housed in the fresh air unit. During painting, the air passes through two stages of filtration (front and ceiling filters) before entering the cabin. The contaminated air is also filtered twice (inlet and outlet filters) before leaving through the extraction unit. Air treatment units are insulated like the side walls to minimize heat loss and are equipped with rubber seals on the covers to protect against possible vibrations and noise. The exhaust air is regulated by a damper in the exhaust air duct, which helps control the cabin’s internal pressure. * PRINCIPLE OF OPERATION FOR THE CABIN: Processes inside the cabin are controlled via an operator panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passes through front filters before entering the distribution chamber at ambient temperature. The air is then extracted through the exhaust unit. Floor filters (paint stop) capture paint particles, and the air passes through final exhaust filters before being released. * FLASH-OFF PROCESS: After painting, the cabin continues to operate for about 15 minutes to expel residual solvents and thinners. During this process, fresh air from outside circulates in the cabin. * DRYING PROCESS: In this phase, 80% of the air circulating through the cabin is heated to 60°C and supplied to the cabin via the distributor. Since 20% of the solvents are released during drying, they are expelled along with this air. Industrial paints are generally dried at 60°C, though the cabin temperature can be adjusted via the operator panel as needed. * COOLING PROCESS: After the 30-minute drying phase, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system is restarted. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices integrated into the cabin. The panel is constructed from robust galvanized sheet metal and steel profiles, and is fully enclosed for protection from dust and moisture. Electrical Components and Switching Panels: Rcsdpswzl Hxefx Af Tef • The switching panel includes all necessary components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for control and command connections between the control panel and motors or other electrical devices. • Wiring is designed to allow for cabin relocation, if required. • Operating equipment is powered at 380 V 50 Hz, while control devices run at 220 V.

Būklė: naujas, Gamybos metai: 2023, Funkcionalumas: visiškai funkcionalus, vėsinimo galia: 295,6 kW (401,90 AG), įvesties srovės tipas: trifazis, aušinimo tipas: vanduo, bendras svoris: 1 453 kg, įėjimo įtampa: 400 V, bendras plotis: 1 000 mm, bendras ilgis: 2 200 mm, bendras aukštis: 1 880 mm, garantijos trukmė: 12 mėnesiai, Wassergekühlter Kaltwassersatz PANASONIC ECOi P WQE1004CA 295,6 kW Rsdowp Duqspfx Af Tecf Kälteleistung: 295,6 kW / 84,05 Tonnen (12/7 — 35°C) Baujahr: 2023 Kältekreisläufe: 2 Stück Wärmetauscher: Plattenwärmetauscher Verdichter: 4 Stück Bitzer GSD80295VAB4-2 (Scroll) Kältemittel: R410a Abmessungen: 2,2 x 1 x 1,88 m Gewicht: 1.453 kg Betriebsstunden: 0/0/0/0 Std. Zustand: Neu ZUSTAND, PRÜFUNG & BEREITSTELLUNG Der Kaltwassersatz wird einer siebenstufigen technischen Überprüfung sowie einer Kontrolle der Betriebsparameter unterzogen. Die Prüfung erfolgt an unserer eigenen Teststation, inklusive Anschluss an Wasser (oder Glykol) und Einstellung der Betriebsparameter nach Ihren Vorgaben. Nach der Prüfung erhalten Sie einen ausführlichen Bericht über die Betriebsleistung und den Gesamtzustand des Kaltwassersatzes. Der Kaltwassersatz ist transportfertig und bereit zur Inbetriebnahme. Unsere Ingenieure unterstützen Sie bei der Kühlleistungsberechnung, der Auswahl des passenden Kühlsystems und der Konfiguration der gewünschten Ausstattungsoptionen. GARANTIE & SUPPORT Die Qualität der Anlage wird durch eine Garantie von 6 bis 36 Monaten bestätigt. LOGISTIK - Weltweite Lieferung möglich - Unterstützung beim Verladen, mit Ausfuhrdokumenten und bei der Logistikkoordination Fordern Sie eine ausführliche Beratung an. Fotos, Videos und ein vollständiger Prüfbericht können auf Anfrage umgehend bereitgestellt werden.

Būklė: naujas, Technines specifikacijas rasite PDF faile. Rcsdpoxp H Rlefx Af Tjf

Būklė: naudotas, Gamybos metai: 2007, Drilling capacity in steel (diameter): 40 mm Throat depth: 1050 mm Spindle speed: 15 – 2800 rpm Feed range: 0.075 – 0.45 mm/min Dimensions (LxWxH): 2450 x 1300 x 2300 mm Weight: 1500 kg Equipment: • Machine in top condition • Serviced and overhauled by factory customer service in 2026 Machine configuration: • Work table 1800 x 600 mm with 4 T-slots • Arm travel 1050 mm • Drilling spindle SK 40 with tool clamping device • Infinitely variable speed control • Infinitely variable quill feed via three-phase servomotor • 2 T-slots (18 mm) at the rear of the machine base • 2 T-slots (18 mm) on the left side of the machine base • Thread cutting device • Centralized lubrication • Coolant system • Machine lamp • CE marking • Safety guard • USB interface Dimensions and travels: Tool holder: SK 40 Column diameter: 195 mm Table size: 1800 x 600 mm Number of T-slots: 4 T-slot spacing: 125 mm Rcjdpfx Afjy Nd T Hs Tjf Quill stroke (Z-axis): 200 mm Column travel (W-axis): 410 mm Distance spindle nose – table min: 70 mm, max: 680 mm Distance spindle nose – floor min: 970 mm, max: 1580 mm Drilling radius: 540 – 1590 mm Work table height: 900 mm Machining performance: Drilling capacity (full) St 60: Ø 40 mm GG 22: Ø 50 mm Tapping capacity St 60: M36 GG 22: M42 Main spindle drive: AC motor, frequency-controlled, 5.5 kW at 100% duty cycle Speed range: 15 – 2800 rpm Max. torque: 250 Nm Constant torque from 15 – 2000 rpm Feed drives: X-axis – AC servomotor: 0.25 kW Y-axis – AC servomotor: 0.25 kW Z-axis – AC servomotor: 4.50 kW W-axis – AC servomotor: 2.50 kW Rapid traverse speeds (X/Y/Z): 7.5 / 7.5 / 5 m/min Rapid traverse speed (W): 3 m/min Infinitely variable feed: 5 – 2000 mm/min Accuracy: Positioning accuracy X-, Y-axis over 1200 mm: ± 0.075 mm Electrical data: Operating voltage/frequency: 400 V / 50 Hz Control voltage: 24 V Hydraulic unit for clamping: 0.75 kW Total connected load: 13.0 kVA Weight Danumeric 440 (without packaging), with table 1800 x 600 mm: 2800 kg CNC Control: Axes: 3 (X, Y, Z) Processor: 32-bit CPU Display: TFT flat screen, backlit, clearly visible from all sides, 215 x 160 mm Position display: Cartesian or polar, absolute or incremental values, unit: mm or inch or degrees Interpolation: 2 axes (X, Y) Technology database: Tool management, tool suggestions according to machining operation, material-dependent cutting data recommendations Tool management capacity: max. 500 tools Subroutine technology: yes Standard software options: Conversational programming, 38 zero point offsets, rotation and mirroring, teach-in for X, Y, Z, program restart with selectable entry functions Zero point detection: Cycles for determining zero points by manual probing of the workpiece for: – arbitrarily clamped rectangular parts – arbitrarily clamped round parts – Centering of cast and flame-cut parts – Angle position detection on round parts by probing reference edges or surfaces Test graphics: Graphical display of drilling patterns

Gamybos metai: 2004, būklė: labai geros būklės (naudotas), Funkcionalumas: visiškai funkcionalus, Pusiau automatinė kompaktiška stiklo sandėliavimo sistema 25 pozicijos Maksimalus stiklo dydis: 3210 x 6000 mm Stalčiaus keliamoji galia: 6000 kg Bendra apkrova: 150000 kg (150T) Rcsdpfx Afezdylxo Tef Labai geros ir švarios būklės Gerai veikianti, patikrinta Parduodama tokios būklės, kokia yra Žiūrėkite vaizdo įrašą

Gamybos metai: 2007, būklė: paruoštas naudoti (naudotas), Parduodamos keturios metalo apdirbimo staklės: 1) Impulsinis suvirinimo aparatas „Cloos GLC 353 MC3“, pagaminimo metai: 2007, svoris: apie 160 kg. 2) MIG/MAG suvirinimo aparatas „Cloos GLC 255“, pagaminimo metai: 2004, matmenys (X/Y/Z): apie 980 mm / 450 mm / 700 mm, svoris: apie 115 kg. Redpfezp Rhhox Af Tscf 3) „hebö“ vielos vyniavimo staklė, tipas II, pagaminimo metai: 1979. 4) Diskinis pjūklas „Eisele VMS II PV-P“, pagaminimo metai: 1974, svoris: apie 290 kg. Apžiūra galima susitarus.