Mandrelio vamzdžių lenkimo staklės

ERCOLINA EB 45 Rohrbiegeautomat CML

Būklė: geras (naudotas), Gamybos metai: 1998, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 35 t, darbinis plotis: 2 000 mm, Press force 35 tons Gedpfxswagyko Ah Aeit Maximum bending length 2000 mm Back gauge Drive power 4.5 kW Weight 3000 kg

Būklė: naudotas, Mitre Cold Circular Sawing Machine Automatic KALTENBACH Type KKS 400 NA Machine No. 101701 Year of Manufacture 1983 Saw Blade Diameter: 400 mm Cutting Capacity at 90° Round: Ø 130 mm Cutting Capacity at 90° Square: 120 x 120 mm Cutting Capacity at 90° Rectangle: 305 x 20 mm Cutting Capacity at 45° Round: Ø 130 mm Cutting Capacity at 45° Square: 110 x 110 mm Cutting Capacity at 45° Rectangle: 245 x 30 mm Clamping Range, Vice Feed: 30 to 140 mm Working Height: 1000 mm Mitre Cutting: 0 - 180° Feed Travel: 600 mm Saw Blade Speed: 10 + 20 m/min, 2 stages Motor Power: 1.7 and 2.6 kW Hydraulic Motor: 1.5 kW Electrical Connection: 380 Volt, 50 Hz - Hydraulic material vice feed with 1500 mm infeed roller conveyor on the left - Dual-stage feed travel up to 1200 mm (feed twice, then saw) - Hydraulic material clamping with vertical clamping cylinder - Mitre cut – saw angle adjusted manually - Hydraulic feed control, cutting speed adjustable manually - 2 motor speeds for saw blade speed Giedpfxed N H A Nj Ah Ajt - Infinitely adjustable saw blade stroke - Coolant system with electric pump integrated in machine base - Hydraulic unit fixed on the base machine - Piece counter with zero reset Space requirement of saw: 2600 x 1200 x 1900 mm Weight of saw: approx. 1400 kg In good condition

Būklė: naudotas, Clamping Plate – Table of a Long Planer Machine – Gisdpsbn Amfofx Ah Ast Table Width / Clamping Width: 1,845 mm Table Length / Clamping Length: 5,505 mm 7 longitudinal T-slots for T-slot nuts: M30 T-slot pitch: 263 mm Overall Length: 6,230 mm Total Plate Height: 350 mm Weight: 11 t

Būklė: geras (naudotas), Gamybos metai: 1999, Mašina je u dobrom stanju. X osovina: 750 mm Y osovina: 400 mm Z osovina: 500 mm Maksimalna brzina vretena: 10.000 o/min Gisdewx Rafspfx Ah Aet

Būklė: geras (naudotas), Gamybos metai: 2010, Funkcionalumas: visiškai funkcionalus, veikimo valandos: 15 996 h, įėjimo įtampa: 400 V, bendras svoris: 6 750 kg, 1000 kN Max. stroke: 200 Weight: 6,750 kg Noise level: 74 dB Year of manufacture: 07/2010 Voltage: 400 V / 50 Hz Rated current: Current operating hours: 15,996 hours with manual angle measurement and correction system with safety laser UVV (accident prevention regulations) inspection performed at regular intervals / maintenance always carried out regularly by Amada Accessories: Tool Die: 2 pcs UKB 20.478 V8/12 30° 835 mm 3 pcs UKB 20.344 V4/V7 88° 835 mm Tool Holders: 4 pcs UKB base for double V die 20.287 + 60.919 835 mm Press Brakes: 5 pcs UKB 10.261 H100 R0.6/90° 2 pcs UKB 11.158 H80 R0.6/30° 2 pcs UKB 11.200 H66 R0.8/90° Other: Light curtain in need of repair (replacement value approx. €4,500) – included separately as a spare part (has been replaced) The machine can be inspected live under power in DE84051 Mettenbach by appointment. Sale only to businesses and under exclusion of any warranty! Gisdpfetwliwex Ah Ajt

Būklė: geras (naudotas), Gamybos metai: 1988, Kraštų lankstymo staklės, lenkimo presas, švytuoklinės lankstymo staklės, štampavimo lenkimo staklės -Pristatymas: esamoje, kaip apžiūrėta, būklėje, žr. nuotraukas -Funkcija: rankinis valdymas (be automatinio režimo) -Gamintojas: RAFAMET švytuoklinės lankstymo staklės, tipas KM-4 -Pavara: mechaninė -Maks. darbo plotis: 2020 mm -Maks. lakšto storis: 4 mm -Atstumas iki atmušos: 750 mm -Galia: kW -Matmenys: 3350/1540/H1510 mm Godpfx Aev Tpxqjh Aoit -Svoris: 3900 kg

Būklė: beveik kaip naujas (naudotas), Funkcionalumas: visiškai funkcionalus, Gamybos metai: 2023, Useful length: 6200 mm Bending capacity Steel 400 N/mm²: 2.00 mm V2A 600 N/mm²: 1.50 mm Aluminium 190 N/mm²: 3.00 mm Number of uprights "S": 6 pieces Driven bending joints "S": 6 pieces Insertion depth: 1165 mm Connection: 400V/3Ph/50Hz Gjdpeyxchnjfx Ah Aeit Other data + dimensions: see brochure Including hydraulic clamping beam adjustment to compensate for different sheet thicknesses Including adjustable clamping beam pre-tension Including 2 hydraulic pressure stages Including safety package Including bending beam extension rail 10 x 60 mm, 2-piece Including double foot switch for clamping beam open/close + automatic bending beam start Including resettable sheet support grate Including waterfold groove in the clamping beam BMS multi-touch control with electronic depth stop TAZ 1000 With this Windows-based graphical touchscreen control unit, profile selection is possible by simply tapping. The simulation program allows observation of the complete bending process of both saved and newly entered profiles. The depth stop is electronically driven by toothed belt and is equipped with 4 stop fingers. The fingers are steplessly adjustable along the entire machine length. Measuring range for depth stop: 10/30 - 945 mm. Network connection for remote maintenance Electric cutter S2 Cutting capacity Steel 400 N/mm²: 2.00 mm V2A 600 N/mm²: 1.25 mm Aluminium 190 N/mm²: 2.50 mm incl. optionally conical depth stop for close/wide edging for easy sheet interlocking Measuring range: 10/30 - 885 mm

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2007, veikimo valandos: 22 605 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 100 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 600 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 1 100 mm, balo svoris: 1 400 kg, bendras svoris: 36 000 kg, alyvos bako talpa: 1 300 l, For sale is a refurbished baler with 100 t pressing force, large format 1100 x 1100 mm, 75 kW drive power, and a 10-fold cross-tying system. Technical Data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main press force: 100 t Prepress force: 50 t Operating hours: 22,605 h Feed opening dimensions: 1,600 x 1,100 mm Filling volume per press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale dimensions: 1,100 x 1,100 mm Drive power: 75 kW Connected load: 126 kW Total current consumption: 238 A Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a Bulk density of 30 kg/m³: approx. 16 t/h Bulk density of 50 kg/m³: approx. 25 t/h Bulk density of 100 kg/m³: approx. 47 t/h Bale weights up to 1,400 kg, depending on material and bale length Oil tank capacity: approx. 1,300 l PLC: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Baler dimensions assembled with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Remarks: The baler has been partially refurbished, serviced in our workshop, tested after completion, and stored. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment works have been carried out: - Derusting and partial repainting of the baler - Complete draining of the hydraulic oil tank, replacement of oil and air filters - Refilled with new hydraulic oil - Replaced all hydraulic hoses - Disassembled, overhauled, and reassembled main hydraulic cylinder, two pre-press flap cylinders, and channel press cylinder: honed cylinder tubes, renewed all seal kits, and carried out final pressure test - Dismantled pre-press flap with bearings and bearing brackets. Removed and re-welded 1st and 3rd arc segment - Renewed both bearings on pre-press flap shaft - Renewed upper material retainer on pre-press flap frame - Dismantled the press ram, inspected and replaced both front running wheels - Removed and replaced material retainers and wear profiles on sides and bottom of the press ram - Dismantled, overhauled horizontal and vertical needle and tying units, replaced plastic sliding plates, bearings for twister shafts and wire guide pulleys on the needle heads - Replaced both bronze slide rails left and right in press ram frame cover - Renewed both wire redirect units left and right, incl. bale retention clamps - Fully renewed wire feeding unit incl. hydraulic cylinder under the needle passages - Welded and smoothed out wire grooves on the bottom and side walls of the press channel - General maintenance and service work according to manufacturer’s recommendations Giodpfovf E Avex Ah Ajt - Baler tested in both manual and automatic mode after completion of refurbishment, accepted and stored All technical information is provided without liability for errors or omissions.

Būklė: labai geros būklės (naudotas), Gamybos metai: 1995, Kombinationseinheit: Hersteller: GSG Zuführeinheit: Typ: 840.02-027 Zerkleinerungs- und Entzunderungseinheit: Typ: 663.02-017 Drahtbereich: Ø5,5–16 mm Für Walzdraht mit ca. 40–60 daN/mm² Festigkeit Zerkleinerungs- und Biegewalzen: Hartmetalleinsätze Verstellung mit 0,37 kW – 1,15 A Getriebemotor Bürstenantrieb mit 0,25 kW Getriebemotor, n=293 min⁻¹ Anschlussspannung: 380–420 V, 50 Hz Trockenbeschichtungseinheit: Typ: BSG/T Befüllung: Calciumstearat (z. B. Traxit Typ: D S 51 E) Stearatverbrauch: ca. 350 g pro t Draht Ziehgeschwindigkeit: max. 15 m/s Elektrische Leistung: 2x 0,55 kW Getriebemotoren Kassette: 2 Steckplätze (1x Walzenblock + 1x Kassette im Lieferumfang enthalten) Typ: PKG/T (TS) Gereinigter Walzdraht Drahtfestigkeit ca. 40–60 daN/mm² Drahtbereich max. Eingangsdurchmesser 9,5 mm, Fertigdurchmesser 3,5–8,5 mm Walzenabmessungen min. Ø115 mm, max. Ø125 mm Bohrungsdurchmesser Ø82 mm, Breite 15–25 mm Kühlstift-Durchmesser 25 mm Kühlwasserverbrauch ca. 600 l/h Ziehmaschine: Hersteller: Koch Typ: KHZ 5000 Baujahr: 1993 Seriennummer: 13.821 Anzahl der Züge: 1 Zug je Block Ziehscheibe: Ø700 mm Zugkraft: mechanisch 5000 N Drahtmaterial: Weichstahldrähte Einspeisefestigkeit: ca. 40–45 daN/mm² Max. Ziehbereich: Eingangsdurchmesser 5,0–8,5 mm Querschnittsreduktion: 20 x 25 % (mechanische Abstufung) Ziehgeschwindigkeit: bis max. 7,0 m/s Giodpfx Ahsr Nfvmj Ast Bremse: Twiflex, Typ: MRB Antrieb: Drehstrommotor/Frequenzumrichter, Siemens PN=110 kW, n=1485 min⁻¹ Spuler: Hersteller: Koch Typ: KHS 1250 Baujahr: 1993 Fabrik-Nr.: 13741 Drahtdurchmesser: 5–8,5 mm Festigkeit: ca. 55–70 daN/mm² Wickelgeschwindigkeit: V=7 m/s, angepasst an die Ziehmaschine Füllgewicht: ca. 3000 kg Spulenantriebsmotor: Drehstrommotor mit Fremdlüfter Typ: 1 PQ 6253 – 6 AA 70- Z A 15 + K 20 + C 14 + H 46 P=37 kW, n=1000–2000 min⁻¹, IP54, Bauform B3 Verlegeantriebsmotor: 66-671U, 1,5 kW, 170 V, 9,8 A, 1680 min⁻¹, IP44, B5-200 Mit angebautem Tachogenerator TG 20, 20 V / 1000 min⁻¹ Mit angebautem Stirnradgetriebe SK 32, i=57,53, Bauform B6 Hydraulik: Hydraulikbagger Typ: H13 AK Pneumatik: Twiflex Scheibenbremse Typ: MRB Pneumatikzylinder Typ: SPWG 28032-25 mm Hub Abmessungen: 3100 x 3000 x 1700 mm (L x B x H) ohne Gegengewicht

Būklė: beveik kaip naujas (naudotas), Gamybos metai: 2000, veikimo valandos: 25 000 h, X ašies eiga: 10 300 mm, Y ašies eiga: 2 000 mm, Z ašies eigos atstumas: 1 800 mm, X ašies padavimo greitis: 10 m/min, Y ašies padavimo greitis: 10 m/min, padavimo greitis Z ašis: 10 m/min, frezos galvos padėtis: 2.5 x 2.5 °, veleno greitis (maks.): 3 000 aps./min, veleno greitis (min.): 60 aps./min, stalo plotis: 3 300 mm, stalo ilgis: 12 000 mm, tvirtinimo skersmuo: 50 mm, bendras aukštis: 48 750 mm, bendras plotis: 100 000 mm, bendras ilgis: 212 000 mm, bendras svoris: 100 000 kg, Duplexfräsen bestehen aus zwei Maschinen, die einander gegenüber angeordnet sind und entweder separat oder als eine Einheit betrieben werden können. Das Werkstück kann mit zwei Spindeln gleichzeitig bearbeitet werden. Produktionssteigerung von bis zu 50 % im Vergleich zu konventionellen Lösungen, also Einzel-Fräsmaschinen Steigerung der Teilegenauigkeit, da die Bearbeitung des Werkstücks in den meisten Fällen in nur einer Aufspannung erfolgen kann Bedienung durch nur einen einzigen Maschinenführer möglich Reduzierter Platz- und Investitionsbedarf im Vergleich zu zwei Einzelmaschinen Schnelle Amortisation durch hohe Produktivität Duplex-Lösungen ermöglichen unterschiedliche Konfigurationen: einzelner Arbeitsbereich oder Pendelbearbeitung Geeignet zur Bearbeitung von Baggerarmen/-auslegern folgender Hersteller: CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo Technische Daten: X-Achse: 10.300 mm Y-Achse: 2.000 mm Z-Achse: 1.800 mm Tischlänge: 12.000 mm Tischbreite: 3.300 mm Tischbelastung: 100.000 kg Spindelleistung: 22/30 kW Spindeldrehzahlen: 60 – 3.000 U/min Spindelaufnahme: 50 ISO/BT/MK Vorschub X-Achse: 10.000 mm/min Vorschub Y-Achse: 10.000 mm/min Vorschub Z-Achse: 10.000 mm/min Fräskopf mit automatischer Indexierung: 2,5 x 2,5° Betriebsstunden: 25.000 h Länge: 21.200 mm Giodorx Rxtspfx Ah Aet Breite: 10.000 mm Höhe: 4.875 mm Gewicht: 100.000 kg