Valdymo blokas

Dietz FDR 132 M/4q Motor SN:3070557 mit FD 71/25q

Sąlyga: paruoštas naudoti (naudotas), Būgniniai varikliai naudoti būgniniai varikliai Gijdpfx Absi A Apuedjl didelės atsargos diržo pločiams nuo 300 iki 1400 mm

Sąlyga: labai geros būklės (naudotas), Schneider SH 07 Vacuum Dissolver ATEX-certified design with wall scraper Drive power: 13 kW Wall scraper power: 2.5 kW Speed range: 380–2000 rpm Mixing vessel: Stainless steel double-jacket, 2 x 100 L usable capacity 50 L heating chamber capacity Mixing vessel: Stainless steel, 1 x 200 L Gsdoimgqmepfx Abdsil Very good condition, directly from production!

Sąlyga: naudotas, mašinos/transporto priemonės numeris: 11666, Rotor diameter: 280 mm Rotor width: 300 mm Giedpfx Aboghgq Nsdol 3-knife rotor 2 rows of stator knives Infeed cross-section approx. 300 x 280 mm Drive motor 11 kW Equipped with noise protection enclosure, noise protection hopper, and extraction fan

Gamybos metai: 1994, Sąlyga: geras (naudotas), Rivo bandsaw sharpening machine Gijdpfx Ajpl D Hxebdel Type GA 250

Gamybos metai: 2025, Sąlyga: naujas, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: GM2000.5000 H-322.41.9000.3E 130.20, Lifting capacity: 5t Reeving: 4/1 Lifting height: 9m Gsdjvx E I Sepfx Abdjil Lifting speeds: 8/1.3 m/min Trolley travel speeds: 20/5 m/min FEM group: 2M Operating voltage: 400V Control voltage: 230V Flange width: 300mm Several units immediately available from stock

Sąlyga: geras (naudotas), Renault 270 DCI crane truck, 19 tonnes. Year: 2002. 470,000 km. Engine replacement performed at 250,000 km. Crane capacity: 5.5 tonnes. Technical inspection: OK. No remote control for the crane. Gijdpfx Aberhzy Hsdsl

Gamybos metai: 1990, Sąlyga: geras (naudotas), Used sideloader Kalmar, the machine has been well maintained For more details, see pictures Gsdpfx Abjh Et E Nodjil

Gamybos metai: 2010, Sąlyga: geras (naudotas), 2 SICON shredders Year: 2010 Electrical cabinet missing Price: €15,000 each Gijdjiz Tm Iopfx Abdol 4 densimetric tables: €8,000 each

Sąlyga: beveik kaip naujas (naudotas), Manufacturer: Flender Type: K2S-2.5 Backstop: Yes Gjdpfxog Stz Ae Abdsil Power: 78 kW Gear Ratio: 44.16:1 Input/Output Speed: 1,400 / 31.7 rpm Input Shaft Ø: 65 mm Output Shaft Ø: 140 mm

Sąlyga: naudotas, Gamybos metai: 2001, Wood dimensions to be processed: Incoming lengths min/max: 500 – 6500 mm; Full optimization up to max. 1500 mm. Incoming widths min/max: 40 – 300 mm. Incoming thicknesses min/max: 15 – 120 mm. Maximum wood cross-sections: 300 x 40 mm, max. 200 x 120 mm. Fixed lengths after saw: min. 510 – 2800 mm. Special application: Cutting of blocks, length min/max: 100 – 200 mm (Note: multiple block length during sorting, blocks are transported to the end of the sorting line and drop into customer-side mesh boxes). Cut/trimming tolerance: +/- 0.8 – 1.5 mm (for wood with minimum resin content and even surface. Tolerance up to 1 m fixed length, max. tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm. Curvature of wood in all directions: max. 10 mm per meter length. Types of wood: Softwood or hardwood. Machine performance: Feed speed continuously adjustable up to max. 230 m/min; cutting cycle 0.6 – 1 s. To determine the practical daily output, an effectiveness factor dependent on the customer’s production conditions must be considered. Infeed and saw working height: 900 mm (install required on customer-side platform, saw requires concrete base). Sorting working height: 2000 mm. Connection values: Total electrical connection load approx. 18 kW. Operating voltage: 380 Volt / 50 Hz. Voltage fluctuations max. 5 %. Air consumption approx. 1200 NL/min. Operating pressure approx. 8 bar. Extraction velocity approx. 30 m/s. Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B. POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge. Pos. 2: Support roller without drive, at the end before steel table for easier feeding. Pos. 3: Length measuring station with built-in fluorescence camera for detecting defect markings. Gjdpfx Ajw Sy T Hebdeil Pos. 4: Automatic non-contact width measurement. Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with built-in waste chute incl. equipment package for large wood cross-sections. Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and plant control. The following are available for processing: - max. 16 product groups - max. 8 qualities per product group - max. 200 fixed lengths per product group. Pos. 6: Discharge conveyor belt as sorting station with drive unit, length 7500 mm. Pos. 7: 2 ejectors mounted on discharge conveyor belt. Location: Nattheim