Stulpinis strėlinis kranas Slankiojantis strėlinis kranas Grandininis keltuvas

Demag KBK Kran Drehkran Hallenkran L 3m Demag KBK1 250Kg + Demag PK Kettenzug

Gamybos metai: 1979, būklė: naudotas, mašinos/transporto priemonės numeris: RS82/12, Technical Data: Psdpfevv N Aujx Adzspt 1x Demag KBK 1 Pillar Slewing Crane, SWL 250 KG with PK Chain Hoist Load capacity at full outreach: 250 KG / 0.25 t Height: approx. 3 m Underside of jib: approx. 2.5 m Outreach: 3 m Hook height: approx. 2 m Total weight: approx. 350 kg Equipped with 250 kg chain hoist Includes pin, cable festoon, trolley, end cap, etc. Slewing range: 300°, connection: 400 V 16 A Crane is dismantled and available immediately Item location: 75053 Gondelsheim, Germany Additional cranes available, load capacity 80-5000 kg; please inquire See pictures Shipping by freight carrier or collection by appointment only.

Būklė: naudotas, mašinos/transporto priemonės numeris: 87 54 41 57, Grinding wheel diameter: 200 mm Grinding wheel width: 30 mm Grinding wheel bore: 51 mm Pjdpfx Adodc Swuezjpt Grinding wheel speed: 3000 rpm Electrical connection: 380 V, 630 W Space requirement: 600 x 260 x 320 mm Approx. weight: 23 kg

Būklė: naujas, Load capacity 500 kg Number of suction pads 6 Diameter of suction pads 215 mm Vacuum Lifter VH 6-500 for horizontal transport of smooth, dry, and airtight panels. Robust load-bearing construction made of steel, painted in RAL 2000 with low dead weight. Comprising: - 1x Galvanized longitudinal beam with a length of 2,400 mm - 3x Galvanized cross beams with a length of 1,000 mm each - 6x Spring-loaded, articulated, and adjustable suction cup holders - 6x Suction cups Ø 215 mm; in case of wear, the seal can be replaced separately from the metal carrier, cost-effectively and without tools - 6x Ball valves to shut off individual suction cups, allowing for the lifting of smaller panels without having to move cups or beams - 1x Spiral connection cable, small coil: * with an extension length of 3,500 mm, designed as an extension cable with CEE plug and coupling * routed alongside the load chain to the lifting device - Low-maintenance, high-quality, dry-running rotary vane vacuum pump with a suction capacity of 8 m³/h and a final vacuum of 85% (150 mbar) - Electrical connection: 3 phase 230/400 V + PE, 50 Hz, with cable (approx. 0.5 m long) and CEE plug (16 A). Isolation transformer integrated into the control panel (necessary if the vacuum lifter is powered via the crane’s trolley and there is no neutral conductor) - Operating handle extendable to 1,000 mm from the center of the beam. Stable metal pocket for your crane control unit included at no extra charge. - Operation "Suction / Release" via manual slide valve: The wear-free and very robust manual slide valve ensures safe suction and release upon activation of the release button. (Double release according to EN 13155) - Control and safety devices for the vacuum lifter: * Robust control box Psdpfxjq Sc Auj Adzopt * Contactor circuit for the vacuum pump * Safety warning system with acoustic signal annunciator * Vacuum gauge with danger zone indicator * Large vacuum reservoir with safety check valve * Double-action release for unloading - Fine dust filter to protect the vacuum pump - Comprehensive and easy-to-understand documentation Warranty against material and manufacturing defects for one year in single-shift operation (excluding wear parts). Initial inspection UVV 18, VBG 9a with CE certificate of conformity according to EN 13155 - Packaging suitable for truck transport.

Būklė: naudotas, Clamping Plate – Table of a Long Planer Machine – Ppedpfxsbn Amfe Adzjt Table Width / Clamping Width: 1,845 mm Table Length / Clamping Length: 5,505 mm 7 longitudinal T-slots for T-slot nuts: M30 T-slot pitch: 263 mm Overall Length: 6,230 mm Total Plate Height: 350 mm Weight: 11 t

Būklė: dilaminuotas dirbtuvėje (naudotas), Gamybos metai: 2007, veikimo valandos: 22 605 h, Funkcionalumas: visiškai funkcionalus, spaudimo jėga: 100 t, pildymo angos plotis: 1 100 mm, pildymo angos ilgis: 1 600 mm, ryšulio plotis: 1 100 mm, ryšulio aukštis: 1 100 mm, balo svoris: 1 400 kg, bendras svoris: 36 000 kg, alyvos bako talpa: 1 300 l, paskutinio kapitalinio remonto metai: 2025, For sale is a refurbished baler with 100 t pressing force, large format 1100 x 1100 mm, 75 kW drive power, and a 10-fold cross-tying system. Technical Data – Baler: Manufacturer: Bollegraaf Model: HBC 110 K / 75 kW Year of manufacture: 2007 Main press force: 100 t Prepress force: 50 t Operating hours: 22,605 h Feed opening dimensions: 1,600 x 1,100 mm Filling volume per press cycle: 3.15 m³ Theoretical cycle time: 19 seconds Bale dimensions: 1,100 x 1,100 mm Drive power: 75 kW Connected load: 126 kW Total current consumption: 238 A Pjdpfxovf E Avs Adzept Tying: 5-fold vertical, 5-fold horizontal, fully automatic Throughput rates at a Bulk density of 30 kg/m³: approx. 16 t/h Bulk density of 50 kg/m³: approx. 25 t/h Bulk density of 100 kg/m³: approx. 47 t/h Bale weights up to 1,400 kg, depending on material and bale length Oil tank capacity: approx. 1,300 l PLC: Telemecanique TSX Micro Operator panel: Schneider MAGELIS Touch Baler dimensions assembled with hopper: 11,750 x 5,000 x 7,105 mm (L x W x H) Transport dimensions baler only: 11,765 x 2,500 x 3,450 mm (L x W x H) Machine weight baler: approx. 36 t Remarks: The baler has been partially refurbished, serviced in our workshop, tested after completion, and stored. The machine is available at short notice and can be inspected at our warehouse by appointment. The following refurbishment works have been carried out: - Derusting and partial repainting of the baler - Complete draining of the hydraulic oil tank, replacement of oil and air filters - Refilled with new hydraulic oil - Replaced all hydraulic hoses - Disassembled, overhauled, and reassembled main hydraulic cylinder, two pre-press flap cylinders, and channel press cylinder: honed cylinder tubes, renewed all seal kits, and carried out final pressure test - Dismantled pre-press flap with bearings and bearing brackets. Removed and re-welded 1st and 3rd arc segment - Renewed both bearings on pre-press flap shaft - Renewed upper material retainer on pre-press flap frame - Dismantled the press ram, inspected and replaced both front running wheels - Removed and replaced material retainers and wear profiles on sides and bottom of the press ram - Dismantled, overhauled horizontal and vertical needle and tying units, replaced plastic sliding plates, bearings for twister shafts and wire guide pulleys on the needle heads - Replaced both bronze slide rails left and right in press ram frame cover - Renewed both wire redirect units left and right, incl. bale retention clamps - Fully renewed wire feeding unit incl. hydraulic cylinder under the needle passages - Welded and smoothed out wire grooves on the bottom and side walls of the press channel - General maintenance and service work according to manufacturer’s recommendations - Baler tested in both manual and automatic mode after completion of refurbishment, accepted and stored All technical information is provided without liability for errors or omissions.

Būklė: beveik kaip naujas (naudotas), Gamybos metai: 2000, veikimo valandos: 25 000 h, X ašies eiga: 10 300 mm, Y ašies eiga: 2 000 mm, Z ašies eigos atstumas: 1 800 mm, X ašies padavimo greitis: 10 m/min, Y ašies padavimo greitis: 10 m/min, padavimo greitis Z ašis: 10 m/min, frezos galvos padėtis: 2.5 x 2.5 °, veleno greitis (maks.): 3 000 aps./min, veleno greitis (min.): 60 aps./min, stalo plotis: 3 300 mm, stalo ilgis: 12 000 mm, tvirtinimo skersmuo: 50 mm, bendras aukštis: 48 750 mm, bendras plotis: 100 000 mm, bendras ilgis: 212 000 mm, bendras svoris: 100 000 kg, Duplexfräsen bestehen aus zwei Maschinen, die einander gegenüber angeordnet sind und entweder separat oder als eine Einheit betrieben werden können. Das Werkstück kann mit zwei Spindeln gleichzeitig bearbeitet werden. Produktionssteigerung von bis zu 50 % im Vergleich zu konventionellen Lösungen, also Einzel-Fräsmaschinen Steigerung der Teilegenauigkeit, da die Bearbeitung des Werkstücks in den meisten Fällen in nur einer Aufspannung erfolgen kann Bedienung durch nur einen einzigen Maschinenführer möglich Reduzierter Platz- und Investitionsbedarf im Vergleich zu zwei Einzelmaschinen Ppedsrx Rxtspfx Adzjt Schnelle Amortisation durch hohe Produktivität Duplex-Lösungen ermöglichen unterschiedliche Konfigurationen: einzelner Arbeitsbereich oder Pendelbearbeitung Geeignet zur Bearbeitung von Baggerarmen/-auslegern folgender Hersteller: CAT, Caterpillar, Komatsu, Hitachi, Hyundai, Doosan, Case, Bobcat, JCB, Kobelco, Liebherr, Kubota, Takeuchi, Volvo Technische Daten: X-Achse: 10.300 mm Y-Achse: 2.000 mm Z-Achse: 1.800 mm Tischlänge: 12.000 mm Tischbreite: 3.300 mm Tischbelastung: 100.000 kg Spindelleistung: 22/30 kW Spindeldrehzahlen: 60 – 3.000 U/min Spindelaufnahme: 50 ISO/BT/MK Vorschub X-Achse: 10.000 mm/min Vorschub Y-Achse: 10.000 mm/min Vorschub Z-Achse: 10.000 mm/min Fräskopf mit automatischer Indexierung: 2,5 x 2,5° Betriebsstunden: 25.000 h Länge: 21.200 mm Breite: 10.000 mm Höhe: 4.875 mm Gewicht: 100.000 kg

Būklė: naujas, Load capacity in kg: 1000 kg Reach: 4000 mm Height: 3000 mm (lower edge of jib) Ppedpfjxak Hxox Adzst Total column height: 3790 mm Slewing range: 270 degrees Total weight: approx. 525 kg Description: - Festoon cable power supply for the trolley - Drag cable with approx. 800 mm cable sag - Ground-controlled operation via pendant control Includes: - ABUS electric chain hoist - Chain hoist type GM 4 1000.5-2, 2-fall - Painted in RAL 5017 traffic blue - Load capacity 1 t - Hook path 3000 mm - Maximum hook position 2442 mm - Design basis FEM 9.901 - Mechanism group 2m / M5 - Hoisting, 2-speed (pole-reversible), 1.3 / 5 m/min - Lifting power 0.22 / 0.9 kW - Duty cycle 60% ED - Switching cycles 360 cycles/hour Overload protection The crane system complies with the requirements of the Machinery Directive 2006/42/EC as well as the currently applicable accident prevention regulations DGUV Regulation 52 (formerly BGV D6). Including: - Anchor rods L200 (set) size LS 200 - Consisting of 8 pieces M27 mm x 800 mm with 1 steel template (500/8) - For foundation attachment, including accessories for grouting To align the slewing crane, an installation gap must be provided between the column base and the building floor. This installation gap must be grouted by the customer after approx. 4 weeks of crane operation. Image shows a similar crane system.

Būklė: naujas, Gamybos metai: 2025, keliamoji galia: 1 000 kg, Various heavy-duty welding tables, machined, partially plasma nitrided Sizes: - 1 x 1 meter, €1,500 - 1.2 x 1.2 meters, €1,700 - 1.5 x 1.5 meters, €1,900 - 2 x 1 meter, €2,300 (plasma nitrided: €3,300) - 2.4 x 1.2 meters, €2,900 (plasma nitrided: €3,900) Pjdjwu Exzepfx Adzopt

Būklė: naudotas, Gamybos metai: 2006, Technical Details: Swing diameter over bed: 500 mm Swing diameter over cross slide: 290 mm Turning length: 850 mm Centre distance: 850 mm Longitudinal travel (Z-axis): 900 mm Cross travel (X-axis): 260 mm Control: Manuaplus 4110 Spindle speed: 10 – 3000 / 2x seples rpm Spindle torque: 920 Nm Spindle bore: 70 mm Cross travel (X-axis): 8 m/min Longitudinal travel (Z-axis): 10 m/min Operating hours / Power-on hours: approx. 34,600 h Tailstock taper ISO: MK 5 Tailstock quill travel: 180 mm Total power requirement: 24 kVA Pedpfx Adowtct Hozjpt Machine weight approx.: 5.2 t Machine dimensions approx. LxWxH: 2.2 x 3.2 x 1.9 m Multifix toolholder size C 3-jaw chuck Ø 250 mm Chip tray Manual hour counter Live centre in tailstock Operation via control panel and monitor Accessories: 4-jaw chuck Ø 250 mm with internal jaws Various chuck keys Machine lighting 8x base plates 4x wedge lifters Various sets of jaws 1x steady rest Ø 100 mm closed

Būklė: labai geros būklės (naudotas), Gamybos metai: 2014, Manufacturer: Spinner Model: TC-400 Year: 2014 Control: Fanuc 32iTB Max. bar capacity: Ø 52 mm Equipment: Short bar loader Spinner Servo-Load 80-1500V2 with support stand Control: Fanuc 32iTB with color LCD screen/control panel 1 Drive motors for X/Z axes and spindle by GE Fanuc, digital AC technology, travel paths X=200 mm, Z=515 mm Main spindle up to 5,000 rpm / 52 mm; Power 18 kW; Torque 113 Nm (S6=40%), main spindle as integrated motor spindle with water cooling, spindle nose A6 C-axis for spindle incl. software option "Transmit" for face machining and "cylindrical interpolation" for peripheral machining Hydraulic hollow clamping cylinder, 12-position turret for tool holders according to DIN 69880/30 mm 12 driven tool stations with turret for milling and drilling operations Ppjdjwwucuopfx Adzot Tailstock for TC400, taper MK4 Chip conveyor TC400, with enlarged, L-shaped coolant tank, approx. 150 liters with centrifugal pump 50 l/min, 3.3 bar Parts catcher, tool measuring arm, high-pressure pump, electrostatic air cleaner