Nuotekų siurblys Kietųjų dalelių siurblys

SDAG Wismut-Aue

Sąlyga: naudotas, Gamybos metai: 2018, System: Decanter Model: Flottweg C4E-4/454 Complete Dewatering Unit in Container Year of manufacture: 2018 Sludge throughput: approx. 0-40 m³/h Solids capacity: max. 1.2 t DS/h Equipment: double doors on face side, side entrance door, fan heater, lighting, power sockets, etc. Bowl: max. rotational speed 3,650 rpm Ijdpfx Afeu R Icmo Istb Bowl diameter: 470 mm System: Containerized unit with swap body system for integration of subsequent plant components. Fully piped and wired, operational as a functional unit. Container unit design: Frame construction, clad with sandwich panels and fittings for swap body system transport. Accessories: FHM PolyMix 4000SP polymer make-up station, measurement equipment, control panel Feed pump: Seepex BN 52-6LS Discharge conveyor: Double trough screw conveyor SS D320 Dimensions: L 7,820 mm x W 2,500 mm x H 3,880 mm Empty weight: 14,500 kg Operating weight: 15,000 kg Voltage: 400 V Current consumption: 142 A Maximum power consumption: 70 kW Fuse protection: 250 A Frequency: 50 Hz Sludge inlet: DN 100 Centrate outlet: DN 200 Solids discharge: Screw conveyor Further information: see photos.

Sąlyga: naujas, Cutting capacity at 90 degrees: round 350 mm Cutting capacity at 90 degrees: square 330 mm Cutting capacity at 90 degrees: rectangular 450x320 mm Saw band length 4250x34x1.1 mm Band speed 40 + 80 m/min Table height 845 mm Saw band width 34 mm Total power requirement 2.2 kW Machine weight approx. 0.985 t Space requirement approx. 1.4 x 2.0 x 2.2 m Double mitre band saw, hydraulic semi-automatic, DGS 350/450 HA-I · Mitre cutting left and right 60° without machine conversion · 34 mm saw band width · Large material support turntable, ball bearing mounted · Saw band guides positioned via extra-wide linear guides Itodpfefgyicex Af Ieb · Heavy-duty, robust gearbox · Large-area clamping plates · Infeed and outfeed roller · Removable chip tray (for cleaning/disinfection) · Free-standing, safe and ergonomic control console · Storage space for saw bands and consumables · Cutting pressure and feed rate regulator · Fully hydraulic vice · Super-fast preclamp (front loading) · Material height sensor (automatic cut-start detection) Semi-automatic operation: 1. Clamp material 2. Start saw 3. Rapid lower feed to material or start cutting for serial cuts 4. Stop saw band 5. Raise frame just above material 6. Release vice Optimal, material-independent cutting results through fine adjustment of the saw frame using: * Pressure control valve (cutting pressure-force) * Feed control valve (speed) * Switches with pictograms, easy and clear to operate

Sąlyga: labai geros būklės (naudotas), rida: 104 242 km, pirmoji registracija: 04/2018, kuro tipas: dyzelinas, ašių konfigūracija: 8x4, ratų bazė: 3 900 mm, kuras: dyzelinas, kuro bako talpa: 500 l, stabdžiai: variklio stabdymas, spalva: mėlyna, vairuotojo kabina: dieninė kabina, pavaros tipas: automatinis, emisijos klasė: Euro 6, Gamybos metai: 2018, Įranga: ABS, AdBlue, centrinis užraktas, elektrinis langų reguliavimas, elektriškai reguliuojamas veidrodis, kruizo kontrolė, navigacijos sistema, oro kondicionavimas, priekabos jungtis, priešrūkiniai žibintai, spoileris, suodžių filtras,

Sąlyga: paruoštas naudoti (naudotas), 26 engines are available. Iodsikrb Ispfx Af Iotb

Sąlyga: naudotas, Tube bending machine, mandrel bending machine, bending machine for tubes and profiles Tube bending unit with SIEMENS servomotor and planetary gearbox Year of manufacture: 2003 Bending capacity: max. Ø 20 x 1 mm Bending radius: max. R 70 mm Bending angle: max. 200° - Last used for round tube Ø 15.4 x 0.8 mm, R60mm - Bending tools and bending dies interchangeable - Drive of the bending tool via AC servomotor and Alpha helical gearbox, planetary gearbox - 2-piece bending tool opens and closes via hydraulic lifting movement - MERKLE hydraulic round block cylinder, Art. 014445 for hydraulic tool opening - Pneumatic height adjustment of the bending die via Festo pneumatic cylinder - Without electrical control - Without hydraulic power unit Dimensions (L/W/H): 760 x 400 x 150 mm Weight: approx. 60 kg Good condition Removed from a functional special-purpose machine, tested prior to removal. Itjdpfxsd E A I Io Af Ieb Drive: Brushless permanent magnet servomotor SIEMENS Type: 1FK6061-7AF71-1EG0 Nominal torque = M0: 6.4 Nm Nominal current = Io: 6.1 A Speed = max. n: 5500 rpm - Brushless permanent magnet servomotor SIEMENS ----- 5 pcs in right-hand version available. 5 pcs in left-hand version available. The quoted price refers to 1 unit of bending unit with servomotor. Individual components of the bending unit can be supplied on request. We also offer the electrical components for servomotor control. Hydraulic power units are also available.

Gamybos metai: 2003, Sąlyga: geras (naudotas), Weishaupt Gas Burner - Monarch Isdpfx Afemdpczo Istb Burner type: G7/1-D Model: ZMD Capacity: 300 - 1750 kW Including gas train (gas valve assembly) Burner was recently in operation

Gamybos metai: 1997, Sąlyga: visiškai atnaujintas (naudotas), 2 units of process design volute casing pumps 1 unit completely overhauled: pump and motor bearings replaced with new ones. Mechanical seal refurbished by a specialist company. All seals renewed. Flow rate: 6 m³/h Delivery head: 25 m Pump speed: 1440 rpm Itsdpfx Afjiuznuj Ijb Shaft seal: double-acting mechanical seal Manufacturer: Burgmann HRZ 13754-00 SIC/SIC/-CAR/SIC-VITON Impeller type: closed two-channel impeller Impeller diameter: 277 mm Bearing type: rolling bearings Impeller side: 1x NU411 Drive side: 2x 7311 Lubrication on drive side: oil Lubricant monitoring: oil level regulator Materials: Pump casing: duplex steel Noridur 1.4593 (9.4460) Wear plate: duplex steel Noridur 1.4593 (9.4460) Pressure cover: duplex steel Noridur 1.4593 (9.4460) Shaft: tempered steel C45+N Impeller: duplex steel Noridur 1.4593 (9.4460) Bearing bracket: cast iron EN-GJL-250 Shaft sleeve: duplex steel 1.4462 Suction nozzle nominal diameter: DN 80 Discharge nozzle nominal diameter: DN 40 Suction side nominal pressure: PN 10 Discharge side nominal pressure: PN 10 Coupling manufacturer: Flender Coupling type: Eupex NH with spacer sleeve Baseplate: cast iron Motor manufacturer: AEG AM 132 Efficiency class: IE 0 Motor speed: 1476 rpm Frequency: 50 Hz Rated voltage: 400 V Motor rated power: P2 7.50 kW Thermal class: F Motor protection class: IP55 Power factor (cos phi): 0.82 Dimensions: Length: 1270 mm Width: 550 mm Height: 570 mm Weight: 300 kg Material 1.4593 Noridur is highly suitable for: - Chemical and process industry - Sulphuric and phosphoric acid - Salt extraction and processing - Petrochemical industry - Coke plants - Textile and pulp industry - Food and sugar industry - Mining/coal extraction and handling - Flue gas desulphurization plants - Acidic, chloride-containing wash suspensions - Acidic process water - Wastewater treatment plants - Offshore and marine engineering

Gamybos metai: 2024, Sąlyga: naujas, Overview – of the various configurations *not every position is needed: Optional: - Bale breaker MHB from €24,990 net - Straw mill MHZ from €7,980 net - Special hopper €970 net - Cyclone from €3,750 net - Sheet metal silo demonstration unit with discharge (only shown schematically in the image) Itsdpfx Asff Sbiof Isb *optional, if feeding with wheel loader is desired Unit price net from €14,750 – demo unit - De-dusting screw conveyor – length approx. 4 m Four sieves are mounted on the underside, which are extracted. Unit price net from: €9,750 - Extraction components / hoses flat rate €945 net - Control system for entire plant Unit price net: €2,750 - Demonstration extraction unit MMJET 160 demo, with cleaning function Connection 160, Fan 2.2 kW Air capacity 1850 m³/400 V automatic compressed air cleaning Unit price net from: €6,950 - Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour at +/- 20 kg tfrom €59,995 net *A reference system (baler) is located at ZIP code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height adaptable upon request) Weight of bale +/- 20 kg (depending on material) Capacity: approx. 30 bales per hour Storage bin approx. 0.7 m³ volume Fill level sensors for min./max. fill level in the bin Hydraulic pre-compressor Hydraulic press ram Hydraulic unit, valve block with oil tank Pump 18.5 kW / 50 liters Rollers in the press channel for easy bale ejection Dimensions (L x W x H) 3105x2830x2455 mm Weight approx. 1500 kg mütek balers / packaging machines were developed for producing bales from various materials such as shredded miscanthus or elephant grass, wood shavings, sawdust, and shredded straw. The machine features robust construction, ensuring consistent quality during continuous operation. The baler compresses the material filled in the storage bin without any additional binding agents by means of hydraulic pressure and packs the material in plastic bags. The machine allows significant volume reduction, depending on the material. Maximum material moisture must not exceed 18% Atro. The mütek baler’s container can be filled automatically or manually and has a capacity of approx. 0.7 m³. Containers with larger volume or with integrated extraction and filter systems as a complete disposal unit are also available. In addition to automatic filling via de-dusting units, mütek also offers filling by means of screw conveyors. Both variants allow automatic dedusting. mütek balers are equipped with a control cabinet for system management. In the standard version, bale dimensions (width x depth x height) are 400 x 400 x 800 mm. Upon request, height can be adapted to your requirements. The following advantages result from baling: - Simple and safe storage - No loose dust - Minimization of storage volume - Low transport volume *Raw material requirements: - dry (max. 30% ATRO) - max. 35 mm length

Gamybos metai: 2006, veikimo valandos: 15 000 h, Sąlyga: geras (naudotas), For sale is an Erema 1007T. Year of manufacture: 2006 Iedpjumubyofx Af Ijtb Operating hours: 15,420 Throughput capacity: 250–350 kg/h The system is currently processing HDPE but is also suitable for other plastics such as LDPE. The machine can be inspected during ongoing operation. A new extruder screw was installed in February.

Gamybos metai: 2018, Sąlyga: naudotas, Naujas: Taip Naudojimo paskirtis: statybos Daugiau informacijos teiraukitės KEY-TEC pardavimų skyriuje. Itodpfx Asg Uqp Ief Isb