Formatinė pjūklas SCM SI 300 nova

SCM SI 300 nova

Sąlyga: naudotas, Holz Her Auriga 1308 FÜ + PU Kompakti konstrukcija – kantų storis 0,4–8 mm SPS ekrano valdymas Edge-Control PPC 221, spalvotas ekranas Išankstinio frezavimo agregatas klijavimo dalies įvedimui Pilnai automatinis briaunų žurnalas – ruloninėms ir juostinėms medžiagoms Klijų uždėjimo stotis GLU JET – kasetės + PU klijavimas – Multisistema+ Klijų padavimas purkštukų technologija Ruoinio aukštis 6–65 mm automatinis klijų aukščio reguliavimas Presavimo įrenginys 1912-3 pneumat. Kampavimo agregatas 1918 pneumat., ruloninei ir juostinei medžiagai iki 8 mm kantų storio Su pneumatine pasukimo nuo 0–10° kampavimo pjūklų nuolydžiu Frezavimo agregatas: lygus frezavimas iki 8 mm, spindulio frezavimas, nuožulnus frezavimas – 15° per valdymo pultą Forminis frezavimo agregatas 1832 pneum., kampų apvalinimui iki 3 mm kantų storio pravažiuojant Nubraukimo agregatas – nuožulas ir spinduliai Plokštuminis nubraukimo agregatas – galutiniam apdirbimui Purkštukų įranga – PU Pilnas DIA įrankių komplektas įsk. Lrjdsxrr Uzopfx Af Iog Mašina pilnai SERVISUOTA, PUIKIOJE BŪKLĖJE Iš sandėlio Lieboch

Sąlyga: naujas, Gamybos metai: 2024, Funkcionalumas: visiškai funkcionalus, X ašies padavimo greitis: 9 m/min, ruošinio aukštis (maks.): 50 mm, briaunos storis (maks.): 5 mm, garantijos trukmė: 12 mėnesiai, HOLZ-HER briaunų klijavimo staklės ARTEA 1020 Sandėlio įrenginys – su galimais tarpiniu pardavimu Pagaminimo metai: 2024 - Bazinis įrenginys 1020 - Edge Control BC15 valdymas su Vi.Se. (Visual Setting) - LED mašinos apšvietimas - Jungimo frezavimo agregatas - GluJet PUR / EVA klijams, su klijų rezervuaru Ledpfx Aexpgv Uef Ierg - Frezavimas - Profilio gramdymas - Paviršiaus gramdymas - Poliravimo agregatas

Sąlyga: labai geros būklės (naudotas), Gamybos metai: 2009, Visapusiško durų rėmų ir apdailos juostų apdirbimo staklės Įrenginys atlieka pjovimą 0°–45°, gręžimą 45°, ekscentrinių jungčių/klipų gręžimą apdailos juostoje, lizdo-plokštelės-kontrplokštės frezavimą, gręžimą rankiniam įsukamų vyrių montavimui. Staklės komplektuojamos su kompiuteriu, kuris automatiškai valdo visus reguliavimus ir darbo ciklą. Ašys varomos bešepetiniais varikliais, visi judesiai vykdomi aukštos kokybės linijiniais guoliais. Didžiausias darbo lauko ilgis: 3 000 mm Mažiausias darbo lauko ilgis: 480 mm Didžiausias detalės aukštis/storis: 98 mm Didžiausias detalės plotis: 280 mm Agregatai kiekvienoje pusėje: 2 Pjovimo agregatai kiekvienoje pusėje: 1 Gręžimo agregatai kiekvienoje pusėje: 1, su 5 grąžtų galvute Lredsw Sd Uuepfx Af Iog Pagrindinis agregatas: 1 Frezavimo agregatas su 2 velenais Pakeliami agregatai su 45° kampu Kampo reguliavimas – programuojamas valdiklis Plotis reguliuojama – programuojamas valdiklis CE atitikties sertifikatas Svoris: 2 500 kg

Sąlyga: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2025, Spindle tiltable: No Height adjustment: Handwheel Tilting adjustment: - Cutter jaw adjustment: Manual Ledpsgzlpkjfx Af Ierg Height display: Mechanical counter Tilt angle display: - Cutter fence display: Mechanical counter Cutter spindle diameter: 30 mm Speeds: 3000, 4500, 6000, 7000, 10000 rpm Motor power: 7 kW Motor brake: Yes, automatic Extraction port: 2 x 120 mm Machine length: 2599 mm Machine depth: 900 mm Weight: 655 kg

Sąlyga: geras (naudotas), Gamybos metai: 2007, Technische Merkmale: - Maximale bearbeitbare Länge: 3.200 mm - Minimale bearbeitbare Länge: 200 mm - Maximale Breite: 200 mm - Minimale Breite: 40 mm - Maximale Werkstückhöhe: 130 mm - Tiefe bei max. Zapfendurchmesser 320 mm: 105 mm - Zapfenwagen-Geschwindigkeit min./max.: 0/100 m/min - Min./max. Profiliergeschwindigkeit: 3/15 m/min Zapfenbearbeitung: 1. Endabschneidsäge - 5,5 PS (4 kW) - Sägeblatt-Ø 400 mm 2. Zapfenfräser - Gegenlager 50 x 620 mm - 15 PS (11,3 kW) - Max. Werkzeug-Ø 320 mm - Achshub 575 mm - Automatischer Splitterschutz 3. Zapfenfräser - Gegenlager 50 x 620 mm - 15 PS (11,3 kW) - Max. Werkzeug-Ø 320 mm - Achshub 575 mm - Automatischer Splitterschutz - Vertikale Positionierung mit durchgehender Achse 4. Digitale Winkeleinstellungsspannung Profilieren: 5. Rechtsprofilfräse - Welle 50 x 320 mm - 10 PS (7,5 kW) - Werkzeug-Ø 130/240 mm - Achshub 280 mm - Zeitverzögerte Splitterschutzvorrichtung bei Kalibrierung - Doppelte Drehrichtung - Vertikale und horizontale Positionierung mit durchgehender Achse 6. Rechtsprofilfräse - Welle 50 x 320 mm - 10 PS (7,5 kW) - Werkzeug-Ø 130/240 mm - Achshub 280 mm - Vertikale und horizontale Positionierung mit durchgehender Achse 7. Rechtsprofilfräse - Welle 50 x 320 mm - 10 PS (7,5 kW) Ledjt R T Hcepfx Af Isrg - Werkzeug-Ø 130/240 mm - Vertikale und horizontale Positionierung mit durchgehender Achse 8. Abschluss-/Aufnahmestation - Vertikale und horizontale Positionierung mit durchgehender Achse - Vorrichtung zum Ausziehen des Fensterladens - Hfutwt78Z 9. Untere horizontale Nutwelle - Vertikale und horizontale Positionierung mit durchgehender Achse - 88,5 PS (66,4 kW) 10. Digitale Führung 11. Teile-Rückführung zum Bediener

Sąlyga: naujas, Gamybos metai: 2023, Oscillating sanders are designed for sanding straight, curved, and shaped pieces with round or oval cross-sections, etc., and with variable thicknesses, suitable for chairs, tables, beds, and related items. The main features of the machine are: frame made of electro-welded steel; rotating disc with two counter-rotating sanding belts driven by an electric motor, with rotational movement around the workpiece; electric control panel; two adjustable workbenches (infeed – outfeed); possibility of fitting two automatic workpiece feed units with adjustable speed via inverter. Sanding belts: 80 x 1260 mm Ledpjqnufvsfx Af Ierg Minimum / Maximum workpiece diameter: 10–100 mm (ø) Minimum bending radius: 200 mm Dimensions: 760 x 1000 x 1800 mm 3 units Camam, Comec, OMEF, Brusa di Garboli

Sąlyga: naujas, Gamybos metai: 2024, Funkcionalumas: visiškai funkcionalus, bendras svoris: 1 240 kg, kuro tipas: dyzelinas, bakelio talpa: 135 l, spalva: balta, išėjimo srovė: 130 A, išėjimo įtampa: 400 V, išėjimo dažnis: 50 Hz, išėjimo srovės tipas: trifazis, nominali galia: 34 kW (46,23 AG), nuolatinė galia: 30 kW (40,79 AG), bendras ilgis: 2 200 mm, bendras plotis: 950 mm, bendras aukštis: 1 230 mm, sukimosi greitis (maks.): 1 500 aps./min, variklių gamintojas: Deutz, Cummins, Ricardo, aušinimo tipas: vanduo, įvesties srovės tipas: trifazis, Three-phase stationary generator set Proton ZPP 30R (30kW - 34kW) in a compact, weather-resistant and additionally sound-insulated enclosure. The genset features an external Automatic Transfer Switch (ATS/Autostart) system as well as many other functions, detailed further in the description. • Model – Proton ZPP 30R SZR • Maximum power output – 34,000 Watts (34kW / 40 kVA) • Rated power – 30,000 Watts (30kW / 36 kVA) • Ready for operation – Yes • Type – Industrial generator set • Condition – Brand new • Manufacturer – Proton • Generator set type – Three-phase • VAT invoice 23% • Year of manufacture – 2024 • Warranty – 36 months ⊳ ENGINE: Engine model – Ricardo MN4100ZDS Fuel type – Diesel Fuel consumption: - 6.5 liters per hour (at 75% load) - 5.0 liters per hour (at 50% load) Engine configuration – Inline (R4) Displacement – 4100 cc Direct injection Lubrication system – Forced lubrication with oil pump ⊳ ALTERNATOR: 100% copper windings AVR voltage stabilizer – Yes Alternator model – Proton 184H Rated output at 400V – 30,000 Watts (30kW / 36 kVA) Maximum output at 400V (up to 15 min) – 34,000 Watts (34kW / 40 kVA) Rated current (400V) – 140.0 A Circuit protection – C16, C32, main – 100A Frequency – 50 Hz Alternator construction – Synchronous ⊳ ENCLOSURE: Sound-insulated housing Weatherproof construction Three-phase and single-phase sockets Fuel tank capacity – 135 liters Operating time on full tank (average) – 20 hours Transport kit – Forklift pockets and HDS crane lifting lugs Dimensions – 220 x 95 x 123 cm Gross weight – 1240 kg ⊳ FEATURES: Voltage stabilizer (AVR) – Stamford SX460 (2%) - Electronic voltage stabilization under variable loads - Electronic frequency stabilization Automatic ATS operation (Automatic Transfer Switch) Overload and thermal protection Oil pressure, oil level, and coolant level sensors Glow plugs Oil pan heater Coolant heater Battery – 2 units of 40Ah Lrsdpfx Afstpvdts Ijg Automatic battery charger ⊳ CONTROLLER: Controller model – Comap InteliLite 4 AMF 20 Engine hours counter Ammeter Voltmeter Integrated PLC logic and PLC editor Overload protection CAN module expansion SCADA system integration Additional outputs – for 4G, Ethernet, RS232/485 connections Remote control and monitoring via GPRS – Optional Communication: Modbus, Ethernet – Optional Why choose us? We are a company specializing exclusively in generator sets, operating in this industry for over 17 years, consistently striving to ensure our products offer top quality and maximum reliability. During this time, we have provided solutions to over 10,000 clients across Poland, even in its most remote regions. We carefully select our genset component suppliers, ensuring they are leaders in their respective industries. We offer a wide range of generator sets from 6 to 300kW, equipped with various engines including British Ricardo, American Cummins, or German Deutz, and we provide custom configurations tailored to specific customer requirements.

Sąlyga: naudotas, Gamybos metai: 2016, MORBIDELLI AUTHOR M400 MAIN FEATURES 5-AXIS PROCESSING UNIT "PRISMA": TOP-LEVEL QUALITY AND PRODUCTIVITY SOFTWARE XILOG MAESTRO: EXTREMELY EASY PROGRAMMING "MATIC" WORKTABLE: SINGLE POSITIONING FOR MULTIPLE OPERATIONS TECHNICAL DATA AUTHORM400 AXES Working area X-axis (reference side): 3,680 mm Working area Y-axis (max. loadable workpiece at rear stops): 1,680 mm Workpiece passage Z / Number of Z axes: 170 mm / 1 Workpiece length for pendulum operation: 1,650 mm Travel speed X-Y axes Pro-Speed: 85 m/min Z-axis speed: 30 m/min INSTALLATION Installed power: 62–82 KVA Compressed air requirement: 400 NL/min Extraction air requirement: 4,430 m³/h Extraction air velocity: 25 m/s Extraction port diameter: 250 mm GENERAL FEATURES CNC-controlled drilling and milling center in gantry design with worktable and workpiece supports suitable for: - Vertical drilling on panel surfaces - Horizontal drilling on all four workpiece edges - Grooving with disc cutter - General milling operations (3-4-5 axes) MACHINE STRUCTURE The base structure is a monolithic construction made of thick-walled steel, reinforced throughout the entire machine bed for extreme rigidity and stability through welded-in reinforcements. The table design with a large base is the key to ensuring permanent precision and stability. The machine layout offers the operator an optimal workflow with a minimal footprint. The moving gantry is built from a solid monoblock and is guided on prism-ground rails with ball-bearing carriages in the X-axis. The mobile unit carries the operating unit, which is also mounted on prism-ground rails and ball-bearing guides. AXIS MOVEMENT All axes move on large-cross-section linear prism guides with wide-bearing ball-bearing shoes to ensure optimal gliding even at the highest speeds and accelerations. The precise and fast positioning of the moving gantry (X-axis) is achieved via rack and pinion with helical teeth. Large-diameter ball screws ensure accurate positioning of the working unit along the moving gantry (Y and Z axes). MOTORS, DRIVES, AND INVERTERS Perfect mechanical dynamics and maximum positioning accuracy are achieved with high-quality drives and brushless motors, sized for speeds up to 90 m/min, ensuring the best possible surface finish. CONTROL SYSTEM The control unit consists of a numerical controller for milling and drilling with "Xilog Maestro" graphic interface on a Windows 7-based Office operating system: - 17" color LCD screen - QWERTY keyboard - Swiveling operator panel - Machine operation interface with Xilog Maestro software Ljdpfxsxnldbj Af Isrg Xilog Maestro Features: Programming - Parametric graphical programming - Import of DXF files (2D; geometries like "SPLINE", "POLYLINE 3D", straight or circular interpolation in three axes, linear in space, spiral in the chosen plane) - Supported programming with graphical and syntax aids for drilling and milling operations - Automatic optimization of drilling operations and tool change cycles - Option to shift panel zero-point for drilling on slanted or curved panel edges

Sąlyga: naudotas, No. 04493 Combined Machine Steko 228 P.B.S. Pressing - Sanding - Sawing Used - Pneumatic veneer press with electric heating Aluminium heating plates 2280 x 1000 mm (L x W) Lower plate extendable Opening width approx. 145 mm Total pressing force 40 tons, maximum specific pressure 2 kg/cm² Heating: 2 x 1.8 kW - Long belt sanding machine 3 kW Table 2600 x 750 mm (L x W), extendable Sanding height 200 mm Belt length 6800 mm Belt width 120 - 150 mm Left/right rotation, speed 19 m/s - Panel saw / veneer saw / trimming saw 2.2 kW With pneumatic pressure beam Cutting length approx. 2600 mm, cutting height adjustable 0 - 60 mm Maximum saw blade diameter 250 mm With chain feed - Extraction unit for sanding machine and saw 0.55 kW Airflow approx. 11 m³/min Push-button control with main and emergency stop switches Machine mounted on chassis Installation footprint (according to manufacturer): 7.5 m² Transport dimensions approx. 3900 x 2100 x 1400 mm (L x W x H) Lsdpfx Asxl Ha Sof Ierg Weight approx. 2500 kg To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended. Sale as is Technical specifications, condition description, year of manufacture, and scope of delivery according to manufacturer's brochure and/or previous owner, without guarantee. Subject to prior sale. For used machines, any warranty is excluded; the following applies: “sold as seen”. Payment terms: Prices plus statutory VAT, payment before collection or shipment Delivery terms: ex stock

Sąlyga: naudotas, Gamybos metai: 2015, Naudotas automatinis formos stiklo pjovimo stalas (jumbo), Intermac tipas Genius 61 CT, pagaminimo metai 2015 Lrodpsxpia Nsfx Af Isg