Quasar pirkti naudotą (9)

Gamybos metai: 2025, Sąlyga: naujas, Tensile/Universal Testing Machine, Test Force 5 kN, excellent WINDOWS software (freely programmable test sequences), over 600 pre-configured test results. GALDABINI: over 30,000 machines delivered worldwide / over 1,000 in Germany Important note before purchasing used universal/tensile testing machines: WIN XP / WIN 7 are "obsolete", these machines, even if expensively purchased, "must" be modernized (electronics, software for WIN10/11, DC disc rotor motor + motor controller). The total cost for purchase, transport, retrofit, commissioning, and subsequent adaptations can become an expensive dead end. And a year later, the gearbox might fail, which is no longer available (…?). Pgodpfx Adedb Nfpjxju New GALDABINI universal testing machine with 2-year warranty, BECKHOFF electronics / premium testing software is often more cost-effective, meets ALL standards, and is universally suitable for: * Tensile tests, compression tests, bending tests, cyclic tests * Brushless AC motor, digital motor controller, BOSCH-REXROTH ball screw spindles * Load cells with 1/100 error 0.5% | 1/500 error 1% * and more Machine price WITHOUT clamping device – must be selected according to your testing application. Included in the price: - Machine fully operational with 2-year warranty - Force accuracy: 0.05 to 5 kN

Sąlyga: labai geros būklės (naudotas), GALDABINI Type: Quasar 50 / Rated Capacity: 50 kN with PC, monitor, and testing software GraphWork 5 Universal Testing Machine Psdpfx Adev Tywqoxsgu The universal testing machines of type "QUASAR" are designed as single-space testing machines and essentially comprise the following assemblies: Machine frame: The construction and structure of the machine load frame are designed to withstand the specified maximum loads where required. Electromechanical load application with toothed belt drive, pulleys, drive with DC or brushless servo motor, and ball screw spindles. Load measurement system with force transducer suitable for both tension and compression tests. Electronic control unit that manages all functions: regulation and control, monitoring, and acquisition of output signals from the measuring amplifiers for force, elongation, and crosshead travel. The system is based on a 32-bit processor with a clock rate of 25 MHz; analog signal acquisition is performed by a 20-bit A/D converter. The electronic controller is usually installed in the machine base alongside most of the electrical drive and power supply components. Operator interface via PC, connected to the electronic control board via a high-speed RS232 serial interface at 38400 baud. Rigid two-column system with a maximum capacity of 50 kN Suitable for metals, plastics, composites, and other materials Stylish design and advanced features Flexible and modular design for easy future upgrades Key technical benefits include extremely high resolution of load and travel values as well as a minimum test speed of 0.0005 mm/min for superior performance and highly accurate results Technical Specifications: Rated capacity: 50 kN Speed at maximum load: 0.0005–200 mm/min No-load speed: 500 mm/min Distance between grips: 1000 mm Total travel: 1000 mm Crosshead travel resolution: 0.1 µm Positioning repeatability: 2 µm Distance between wedge grips: 480 mm Clearance between columns: 410 mm Force units: Newton - daN - kgf - lbs Dimensions: Height: approx. 1548 mm Width: approx. 700 mm Depth: approx. 730 mm Power connection: 220V (+10%) 50 Hz Power consumption: 0.65 kW Weight: approx. 255 kg without accessories Recommended lighting during use: 300 lux Weight: approx. 255 kg Condition: used Scope of delivery: (see picture) (Subject to changes and errors in technical data, specifications reserved!) For further questions, we are happy to assist you by phone.

Gamybos metai: 2025, Sąlyga: beveik kaip naujas (parodų įrenginys), Tensile / Universal Testing Machine, 200 kN test force, excellent WINDOWS software (freely programmable test procedures), over 600 pre-configured test results. GALDABINI: >30,000 machines delivered worldwide / Germany >1,000 Important note before purchasing used universal / tensile testing machines: WIN XP / WIN 7 are 'obsolete', these machines—often purchased at high cost—must be modernized (electronics, software for WIN10/11, DC disc armature motor + motor controller). The total cost for purchase, transport, retrofit, commissioning, and refurbishing can turn into an expensive dead end. And one year later, the gearbox—which is no longer available—fails (... ?). New GALDABINI Universal Testing Machines with 2-year warranty, BECKHOFF electronics, premium testing software are often more cost-effective, comply with ALL standards, and are universally suitable for: * Tensile tests, compression tests, bending tests, cyclic tests * Brushless AC motor, digital motor controller, BOSCH-REXROTH ball screws * Force transducers with error margin 0.5% at 1/100 | 1% at 1/500 * Etc. Machine price EXCLUDES clamping fixtures—these must be selected according to your specific testing requirements. Included in the price: - Fully functional machine with 2-year warranty Pgedpfecyamwox Adxou - Force accuracy: 2 to 200 kN

Gamybos metai: 2025, Sąlyga: beveik kaip naujas (parodų įrenginys), Tensile / Universal Testing Machine with 50 kN test force, excellent WINDOWS software (freely programmable test sequences), over 600 ready-to-use test result templates. GALDABINI: Over 30,000 machines delivered worldwide / over 1,000 in Germany Important note before purchasing used universal / tensile testing machines: WIN XP / WIN 7 are "obsolete"; these expensive machines "must" be upgraded (electronics, software for WIN10/11, DC disc rotor motors + motor controllers). The total cost for purchase, transport, retrofit, commissioning, and required modifications can quickly turn into an expensive dead end. And a year later, the gearbox, which is no longer available as a spare part, may fail (... ?). A new GALDABINI universal testing machine with 2-year warranty, BECKHOFF electronics, and premium test software is often more cost-efficient, fully compliant with ALL standards, and is universally suitable for: * Tensile testing, compression testing, bending tests, cyclic tests * Brushless AC motor, digital motor controller, BOSCH-REXROTH precision ball screw drives Pgedpfx Asptcmedxsu * Load cells with accuracy from 1/100 at 0.5% error | 1/500 at 1% error * etc. Machine price EXCLUDES clamping fixtures – these must be selected according to your testing requirements. Included in the price: - Fully functional machine with 2-year warranty - Force measurement accuracy: 0.5 to 50 kN (

Gamybos metai: 2025, Sąlyga: beveik kaip naujas (parodų įrenginys), Tensile / Universal Testing Machine with a test force of 10 kN, excellent WINDOWS software (freely programmable test sequences), over 600 pre-configured test results. GALDABINI: over 30,000 machines delivered worldwide / over 1,000 in Germany Important note before purchasing used universal / tensile testing machines: WIN XP / WIN 7 are “obsolete”; these expensively purchased machines "must" be modernized (electronics, software for WIN10/11, DC disk rotor motor + motor controller). The total cost for purchase, transport, retrofit, commissioning, and rework can quickly become a costly dead end. And one year later, the gearbox may fail (...?). A new GALDABINI Universal Testing Machine with 2-year warranty, BECKHOFF electronics, and premium testing software is often more affordable, meets ALL standards, and is universally suitable for: * Tensile tests, compression tests, bending tests, cyclic tests * Brushless AC motor, digital motor controller, BOSCH-REXROTH ball screw drives * Load cells: from 1/100 - error 0.5% | 1/500 - error 1% Pgsdpfx Adodb Nf Ioxeu * etc. Machine price WITHOUT clamping device - must be selected to suit your testing application. Price includes: - Fully functional machine with 2-year warranty - Force accuracy: 0.1 to 10kN (

Gamybos metai: 2025, Sąlyga: beveik kaip naujas (parodų įrenginys), Tensile / Universal Testing Machine, test force 100 kN, outstanding WINDOWS software (freely programmable test procedures), over 600 predefined test results. GALDABINI: more than 30,000 machines delivered worldwide / over 1,000 in Germany Important notice before purchasing used universal / tensile testing machines: WIN XP / WIN 7 are ‘obsolete’, these expensive machines ‘must’ be upgraded (electronics, software for WIN10/11, DC disc rotor motor + motor controller). The total cost for purchase, transport, retrofit, commissioning, and post-purchase corrections can quickly turn into an expensive dead-end. And a year later, the gearbox—which is no longer available—fails (... ?). Pgjdscxwq Repfx Adxeu New GALDABINI universal testing machine with 2-year warranty, BECKHOFF electronics / premium test software are often cheaper, comply with ALL standards, and are ideally suited for: * Tensile tests, compression tests, bending tests, cyclic tests * Brushless AC motor, digital motor controller, BOSCH-REXROTH ball screws * Load cells with accuracy: 1/100 error 0.5% | 1/500 error 1% * etc. Machine price WITHOUT clamping fixture - must be selected specifically for your testing application. Included in the price: - Machine fully functional with 2-year warranty - Force accuracy: 1 to 100 kN

Gamybos metai: 2025, Sąlyga: beveik kaip naujas (parodų įrenginys), Tensile / Universal Testing Machine with 1200 kN test force, excellent WINDOWS software (freely programmable test sequences), over 600 ready-made test result templates. Pgjdpfx Aodb Ndcedxju GALDABINI: More than 30,000 machines delivered worldwide / over 1,000 in Germany Important note before purchasing used universal / tensile testing machines: WIN XP / WIN 7 are “obsolete,” and these expensive machines "must" be modernized (electronics, software for WIN10/11, DC disc rotor motor + motor controller). The final cost for purchase, transport, retrofit, commissioning, and subsequent improvements can easily become a costly dead end. And one year later, a gearbox that can’t be sourced fails (... ?). A new GALDABINI universal testing machine with 2-year warranty, BECKHOFF electronics, and premium test software is often more cost-effective, complies with ALL standards, and is universally suitable for: * Tensile, compression, bending, and cyclic tests * Brushless AC motor, digital motor controller, BOSCH-REXROTH ball screw drives * Load cells with up to 1/100 error at 0.5% | 1/500 error at 1% * etc. Machine price WITHOUT clamping fixtures – must be selected for your specific testing task. Price includes: - Fully functional machine with 2-year warranty - Force accuracy: from 12 to 1200 kN

Sąlyga: naudotas, Gamybos metai: 2014, So ein Kombi-Angebot begegnet Ihnen nicht jeden Tag... Wir bieten das Komplettpaket an, auf Wunsch aber auch getrennt in zwei Einheiten: 2014 Quaser UX 300 – 5-Achs-Bearbeitungszentrum mit Halter 12-Stationen-Stapelpalettensystem (aktuell für Schunk Zero Point Paletten konfiguriert, kann aber angepasst werden), bedient von einem Fanuc M20i A Roboter. Quaser Maschinen (vergleichen Sie hierzu auch die Hardinge Bridgeport XR-Serie, gefertigt von Quaser) zeichnen sich durch eine robuste Bauweise mit massivem Graugussbett und hochwertigen Linearführungen aus – das sorgt für außergewöhnliche Stabilität und minimiert Vibrationen während der Bearbeitung. Diese Konstruktionsstärke ist entscheidend für die Einhaltung enger Toleranzen und erstklassiger Oberflächengüten. Hinweis: Der Halter Palettenpool und der Roboter können bei Bedarf auch separat erworben werden. Quaser Spezifikationen: - Voll simultanfähiges 5-Achs-Bearbeitungszentrum mit Schwenktisch, C-Achse 360°, B-Achse +30°/-120°, 15.000 U/min BBT 40 Spindel, 60-fach Werkzeugwechsler, automatische Tür, Blum Laser- und Messtastersystem, Innenkühlung, gekühlte Spindel, Späneförderer, Brandschutzsystem, robotergestützte Automatisierung (optional) - Wie fotografiert direkt nach Ankunft – weitere Bilder folgen nach der Inbetriebnahme. Technische Daten: - X-Verfahrweg: 410 mm - Y-Verfahrweg: 610 mm Pedswzyxcopfx Adxsgu - Z-Verfahrweg: 500 mm - 15.000 U/min BBT 40 Spindel (Plan- und Konusaufnahme) mit Kühleinheit und Innenkühlung - Steuerung: Heidenhain iTNC 530 HEIDENHAIN smart NC - Tischdurchmesser: 320 mm - Tischbelastung: 100 kg - Werkzeugplätze: 60 - Anschlusswert: 35 kVA - Maschinengewicht: ca. 7,4 t - Maschinenabmessungen (LxBxH): ca. 4,15 x 3,8 x 3,28 m Halter LoadAssistant 12 (im Paket mit Quaser UX 300 oder einzeln erhältlich): Der Halter „by Fastems“ LoadAssistant-2 Mill Stacker ist eine eigenständige Einheit mit 12-Stationen-Rundstapeltisch, kompletter Schutzumhausung, Lichtschranken und Fanuc M20i A Roboter. Aktuell für Schunk Zero Point Spannsysteme konfiguriert – kann nach Bedarf angepasst werden. Diese Stand-alone-Lösung ist ideal für Serienbearbeitung bzw. mannlose Fertigung und lässt sich bei Nichtbedarf abkoppeln. Technische Daten: - Mindestwerkstückgröße (LxB): 40 mm x 40 mm - Max. quadratische Werkstückgröße (LxB): 145 mm x 145 mm - Max. rechteckige Werkstückgröße (LxB): 40 mm x 200 mm - Werkstückhöhe (min – max): 10 mm – 175 mm - Max. Traglast Roboterarm: 20 kg - Max. Gesamtnutzlast Drehtisch: 660 kg - Max. Stapelhöhe: 375 mm - Anzahl Stapelplätze (davon 1 leer): 12 - Max. Gewicht pro Station: 60 kg - Max. Werkstückanzahl bei 10 mm Höhe: 407 Stk. - Max. Werkstückanzahl bei 20 mm Höhe: 198 Stk. - Max. Werkstückanzahl bei 50 mm Höhe: 77 Stk. - Max. Werkstückanzahl bei 70 mm Höhe: 55 Stk. - Max. Werkstückanzahl bei 85 mm Höhe: 44 Stk. - Max. Werkstückanzahl bei 110 mm Höhe: 33 Stk. - Max. Werkstückanzahl bei 150 mm Höhe: 22 Stk.

Sąlyga: geras (naudotas), Gamybos metai: 2001, Funkcionalumas: visiškai funkcionalus, Auction without reserve price – guaranteed sale to the highest bidder. Used optimizing cross-cut saw line Opticut 350-4 with Dimter OptiCom program assistant. The saw and both associated manual laser marking stations are still in operation and running without issues. Dismantling of the machine must be carried out strictly within the period 27.11. – 01.12.24. Submitting a bid constitutes a binding agreement to comply with this deadline. TECHNICAL DETAILS Wood dimensions: Wood length with infeed via table: min. 500 mm Wood length with infeed via transverse chain or scanner: min. 900 mm Wood length with infeed via laser marking: min. 1,200 mm Max. infeed length: 3,300 or 6,300 mm Wood width: 30 - 230 mm Wood thickness: 12 - 100 mm Max. wood cross-section: 230 x 25 mm / 200 x 60 mm / 120 x 100 mm Saw station: Feed speed steplessly adjustable, max.: 230 m/min Cycle time per cross-cut including braking, cutting, acceleration: 0.6 - 1.0 s Saw blade, carbide tipped, diameter: 450 mm (500 mm) Saw blade bore diameter: 30 mm Psdsu N Iw Ispfx Adxjgu Saw blade speed: 4,100 rpm Saw motor power: 7.5 kW Min. fixed length: 180 mm Optimization features: Max. product groups: 16 Max. quality grades: 8 Max. fixed lengths: 400 mm Included with the system: 2 laser marking stations with roller conveyor and under-table cross-cut saws Infeed approx. 5 m long before the optimizing cross-cut saw (OKS) OKS Weinig OptiCut 350-4 with waste chute Outfeed conveyor after OKS with Quasar moisture meter Control cabinets and safety fencing