Giluminio gręžimo staklės Mollart - LD8 - 150

Mollart LD8 150 Pellet Die

Būklė: naudotas, Gamybos metai: 1961, Darbinio skersmuo - maks. 100 mm Darbinio skersmuo - min. 10 mm Darbinio ilgis 1000 mm Bendra galios poreikis 16 kW Bjdpfx Answwl I Ie Hewu Staklių svoris apie 3 t Užimama vieta apie 0 m Vadeliai buvo perrinkti prieš 10 metų.

Būklė: naudotas, Thread rolling machine, cold rolling machine, thread roll machine, profile rolling machine Manufacturer: PEE-WEE Model: UPW 24 Serial no.: P07 Year of manufacture: 2007 Max. rolling force: 24 tons Max. tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool mounting length/tool length: 180 mm Max. workpiece diameter: 50 mm Hydraulic motor output: 3 kW Roll drive motor output: approx. 5.5 kW Mains connection: 400 Volt, 50 Hz, 10 kW - Swiveling roll spindle for through-feed thread rolling - Roll spindle speed in 4 steps via gear shifting - Hydraulic unit integrated in machine bed - Operating manual with electrical schematic diagram Bsdpeuz If Nofx An Hewu Required space (L x W x H): 2000 x 1450 x 190 mm Weight: approx. 3 tons Very good condition Plunge rolling: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length equals the width of the rolling tools. Through-feed rolling: Used when the thread length is greater than the width of the rolling tools. Through-feed tools have three sections – the lead-in, the calibration section, and the lead-out. Groove rolls have no pitch and are swiveled to match the lead angle of the profile to be rolled. Pitch rolls differ from groove rolls by having a pitch in the profile. The sum of the pitch angle and swivel angle results in the lead angle in the workpiece.

Gamybos metai: 1995, būklė: naudotas, mašinos/transporto priemonės numeris: 18891, Tractive force: 10 tons. Stroke: 1000 mm. 3 ejector stations. With chip conveyor and platform for above-ground installation, including safety door. Bedsbrcmkspfx An Hswu

Būklė: naudotas, Gamybos metai: 2005, Turning diameter: 275 mm Turning length: 900 mm Control system: TRAUB TX8i Spindle bore: 65 mm Drive power, 100% duty cycle: 25.20 kW Drive power, 40% duty cycle: 30.20 kW Torque at 40% / 100% duty cycle: 180 / 135 Nm Spindle speeds, stepless: 1 - 5,000 rpm Spindle diameter in front bearing: 110 mm C-axis: 1 - 500 rpm Tool turret No. 1 X-axis: 290 mm Y-axis: 165 mm Z-axis: 600/950 mm B-axis: 360° Rapid traverse X/Y/Z: 18 / 18 / 30 m/min Feed force X/Y/Z: 10 / 10 / 7 kN Number of tools: 2x2 + 2x2 Number of driven tools: 2x2 + 2x2 mm Tool speeds: 8,000 / 2,000 rpm Drive power, 25% duty cycle: 5.80 kW Torque at 25% duty cycle: 4x18.6 / 4x74 Nm Tool holder: TRAUB Ø60 Tool turret No. 2 / No. 3 / No. 4 X-axis: 170 mm Z-axis: 600/950 mm Y-axis: +/- 60 mm Rapid traverse X/Y/Z: 18 / 15 / 30 m/min Feed force X/Y/Z: 10 / 10 / 7 kN Turret - number of stations: 10 Number of driven tools: 10 mm Tool speeds: 1 - 6,000 rpm Drive power, 25% duty cycle: 5.80 kW Torque at 25% duty cycle: 18.60 Nm Tool holder: DIN 69880 Ø40x63 Bar feeder: DNH61 / 3000 Bar lengths: 1,000 - 3,200 mm Bar diameter: 18 - 63 mm Max. hexagon: 45 mm Total power requirement: 95.00 kW Machine weight approx.: 16.00 t Installation dimensions approx.: 10.00 x 3.50 x H3.00 m Equipped with TRAUB TX 8i control, main and counter spindle with C-axis, 3 turret tool carriers, 1 vertical tool carrier with B-axis, extraction system, chip conveyor, coolant system with coalescence separator. Bwsdpjw E Nnbofx An Hsu Bar loader: TRAUB Stamag DNH61 / 3000 2 pcs. 3-jaw chucks SMW KNCS-N 170-43 2 pcs. HAINBUCH collet chucks 40 pcs. various static tool holders 6 pcs. various driven tool holders Spare parts package The machine can be inspected under power.

Būklė: geras (naudotas), Gamybos metai: 2008, Funkcionalumas: visiškai funkcionalus, Produktionslinie eines kanadischen Herstellers, Brunette, die sich durch hohe Leistungsfähigkeit und Langlebigkeit auszeichnet. Bwodpfxjvu D Dws An Heu Das Angebot umfasst eine Entrindungsmaschine für Rundholz mit Zufuhrtischen, Rindensammel-Förderern sowie einen Hacker mit einer installierten Leistung von 630 kW und einem Doppelschnecken-Austragsförderer.

Būklė: labai geros būklės (naudotas), Gamybos metai: 2001, veikimo valandos: 4 500 h, Funkcionalumas: nepatikrintas, mašinos/transporto priemonės numeris: 090119, Country of Manufacture: CE - Germany Voltage: 400V Net Weight: 7,500 kg Dimensions: 2.9 x 2.3 x 2.3 m Operating hours: 29,731 h, Working hours: 4,500 h TECHNICAL DATA AXES Maximum travel X-axis: 400 mm Maximum travel Y-axis: 300 mm Maximum travel Z1-axis: 475 mm Maximum travel Z2-axis: 475 mm B-axis rotary position: 0.0001 – 360° C1/C2-axis rotary position: 0.0001 – 360° WORKPIECE Maximum cubic dimension: 80 x 80 x 80 mm Maximum workpiece weight: 5 kg TURRET HEAD Number of positions: 24 Number of controlled positions: 18 Number of fixed positions: 6 Maximum tool holder (round): Ø 20 mm Maximum tool holder (square): 16x16 mm (20x20) Max. turret head movement above tool tip: 500 mm Rotating tool speed: 1–9,000 rpm SPINDLE Maximum spindle speed: 6,000 rpm Maximum bar diameter: Ø 42 mm Maximum clamping chuck diameter: 140 mm BAR MACHINING Maximum bar length (bar feeder): 1,000 mm Maximum workpiece size for bar gripper: Ø42 x 100 mm Maximum gripper diameter: 42 mm Clamping cylinder tensile and compressive force: 20,000 N FEED Feed force X-axis: approx. 895 daN Feed force Y-axis: approx. 895 daN Feed force Z1-axis: approx. 895 daN Feed force Z2-axis: approx. 895 daN Rapid traverse X/Y/Z axes: 20 m/min Tool control motor torque: 2.4 Nm Spindle S1 / Spindle S2: 70 Nm COOLING (Performance Values) Chip conveyor immersion pump output: approx. 10 l/min at 4.5 bar / 80 l/min at 3.2 bar / 150 l/min at 0.7 bar High-pressure pump output in conveyor: 10 l/min at 13.2 bar / 50 l/min at 9 bar / 90 l/min at 1 bar Lubricant volume in chip conveyor: approx. 134 L Coolant volume in cooling unit: 45 L CONTROL: Siemens 840D WORKING PRECISION Resolution X/Y/Z: 0.1 µm Resolution B-axis: 0.0001° Resolution C-axis: 0.0001° Positioning accuracy: 5 µm Accuracy: 0.6 µm Maximum run-out error: 0.5 µm ELECTRICAL Spindle 1 / Spindle 2 (at 100%): 11 kW Spindle 1 / Spindle 2 (at 40%): 15 kW Feed motor axes X/Y/Z1/Z2: 1.3 kW B-axis: 1.3 kW Tool control: 2.3 kW Hydraulic pump: 7.5 kW Hydraulics return stroke: 0.75 kW Cooling unit fan 1 / 2: 0.18 kW Circulating pump (cooling unit): 1.1 kW Cooling unit compressor: 2.2 kW Chip ejector: 0.25 kW Emulsion pump 1: 1.1 kW Emulsion pump 2: 2.2 kW Operating voltage: 400 V Mains frequency: 50 Hz (60 Hz optional) Control voltage: 24V DC Total power: 35 kW Rated current: 63A Connection: Network TM / TT / IT PNEUMATICS Maximum operating pressure: 10 bar Normal operating pressure: 6 bar Minimum operating pressure: 5 bar Air output: approx. 150 L/min Solenoid voltage: 24V DC Oil mist tank capacity: 12 L Quality standard: 2 as per Pneurop 6611 NOISE EMISSIONS Normal operation: 78—80 dB Technical data subject to change or error, information provided without obligation. Inventory No. 2321018, Machine consisting of: - Chip conveyor - Preparation for bar feeder Tool holders: 6 fixed drill holders ER32 8 turning tool holders 5 driven tool holders ER32 4 driven tool holders ER25 6 driven tool holders ER20 Bodpfeht Hg Djx An Hewu

Būklė: geras (naudotas), gręžimo gylis: 1 500 mm, padavimo ilgis X ašis: 2 000 mm, padavimo eiga Y ašimi: 1 300 mm, padavimo ilgis Z ašis: 1 500 mm, Manufacturer: TBT Tiefbohrtechnik Model: BW 250-S Control: SIEMENS 840D Year of manufacture: 2007 Drilling, milling, and tapping for heat exchanger tube sheets and plates Swiveling A-axis: +25 to -15 degrees Filtration and coolant system: 1000 L Chip conveyor: 2000 x 1200 mm, discharge height Milling tool changer tower station: 20 positions ELB drilling capacity: 3 - 35 mm Milling capacity: 250 cc/min Feed rates all axes (X-Y-W-Z): 15,000 mm/min Cutting hours: approx. 15,000 Comes with an extensive tooling package Specifications Metric | US Standard Max. drilling Ø in steel: 40 mm Drilling depth: 1,500 mm X-axis: 2,000 mm Y-axis: 1,300 mm Z-axis: 1,500 mm W-axis: 750 mm Table load capacity: 15,000 kg Table dimensions (L x W or Ø): 1,600 x 1,200 mm Spindle mount: HSK 63 Mk Spindle power: 11 kW Speed: 8,000 rpm Dimensions (approximate) Length: 7,200 mm Width: 7,800 mm Height: 4,250 mm Bjdpov A Uw Defx An Hewu Weight: 23,000 kg Please note: The information on this page has been provided to the best of our knowledge and wherever possible, sourced from the manufacturer. The information is given in good faith, however accuracy cannot be guaranteed. Accordingly, these details do not constitute representations or contract terms. We recommend verifying all critical details independently.

Būklė: naudotas, Centrių atstumas: 2 500 mm Centrių aukštis: 250 mm Šlifavimo disko skersmuo: 600 mm Šlifuoklio stovo eiga: 320 mm Bwedox Avtcjpfx An Heu Ruoinio veleno sukimosi greitis: 50–450 min⁻¹ Tvirtinimas MK5 Atraminė griebtuvė MK Apvalaus šlifavimo staklės | NAXOS-UNION - W-500 2017 m. apvalaus šlifavimo staklės buvo pilnai renovuotos (RETROFIT) KPS-Schleiftechnik firmos (žr. užsakymo patvirtinimą). Įrenginys gerai prižiūrėtas. Daugiau techninių duomenų rasite pasiūlyme.

Būklė: geras (naudotas), Gamybos metai: 2002, Apdirbamo detalės skersmuo – 40 mm Modulis – maks. 2 Modulis – min. 0,1 Apdirbamos detalės ilgis – maks. 665 mm Bwsdpfx Aov Ucdvon Hsu Svoris – 4,5 t Veleno skylės skersmuo – 30 mm Valdymo sistema – Siemens Frezavimo įrankio guolio skersmuo – 20 mm Bendras galios poreikis – 5,5 kW Techniniai duomenys Maks. modulis – 2 Žingsnis – 0,5–25 mm Perdavimo skaičius – daugiastepis Maks. apdirbamos detalės skersmuo – 40 mm Maks. apdirbamos detalės ilgis – 180 mm Maks. frezavimo įrankio skersmuo – 80 mm Maks. frezavimo įrankio plotis – 12 mm Z ašis (frezavimo ilgis su priešine galvute) – 90 mm Z ašis (frezavimo ilgis be priešinės galvutės) – 113 mm Frezavimo galvutės pasvirimo kampas – 30° / 30° Aprašymas Žygne ratų frezavimo ir sriegių pjovimo staklės LAMBERT – 124 CNC Staklės yra geros būklės.

Būklė: naujas, The CR 35 (up to Ø 3.5 mm) completes the range between the CR 23 (up to Ø 2.3 mm) and the CR 45 (up to Ø 4.5 mm). The machine features between 12 and 16 axes; the 12 base axes are listed below: Bwedpfx Anovbdq Re Hsu - wire feed - wire rotation - nozzle rotation - one servo spinner - 8 independent slides (8 axes) Optional (up to 4 additional axes): - servo cutter - additional servo spinners - lateral movement of the coiling finger - transfer for lifting the second (German type) loop for tension spring production. Maximum feed speed: 54 m/min. Machine dimensions: 2.36 x 2.10 x 2.10 m. Machine weight: 2,300 kg. Please do not hesitate to contact us if you have any further questions.