Metalinės dalies purkštuvas

Magido / Glogar L90

Gamybos metai: 2026, būklė: naujas, Parts Cleaning System, Spray Cleaning Machine Type L90 Automatically operating hot water parts washer with automatic basket drive via geared motor, stainless steel wash pump (make: Lowara), circulating 3-sided spray system (from below, side, and above) with stainless steel nozzles - Basket diameter: 790 mm - Useful height: 500 mm - Max. load weight: 150 kg - Spray pressure: 3 bar - Tank volume: 105 liters - Heating: electrically adjustable (room temp. – 90°C) Machine dimensions (LxWxH): 1,150 x 1,250 x 1,900 mm Empty weight: approx. 220 kg Washing cycle timer adjustable via Omron timer (minutes and hours) Complete cleaning system (interior and exterior cladding) made from stainless steel 1.4301 Rjdpfx Aehgh I Sscajcd Water circulation system and loading basket made from stainless steel 1.4301 Full system insulation (tank and cabin) made from stainless steel 1.4301 Mechanical lid locking Bath cover with fine filter (2,000 micron) Suction filter for pump protection Operating hours counter Steam extraction including condensate return Prepared for later installation of an oil separator The parts washer is as new, never used. OTHER BASKET DIMENSIONS AVAILABLE ON REQUEST!!!

Būklė: beveik kaip naujas (parodų įrenginys), ATEX-CERTIFIED PUMP Oil-bath rotary vane vacuum pump. Available in stock. Fully overhauled unit. Supplied with warranty. Nominal flow rate: 30 m3/h at 50Hz. Ultimate vacuum: 1x10^-3 mbar abs. For any questions, please contact us. Rsdpfx Aoftzgxjcajcd

Būklė: naujas, Gamybos metai: 2026, Funkcionalumas: visiškai funkcionalus, įėjimo įtampa: 230 V, įvesties srovės tipas: Oro kondicionierius, lazerio galia: 30 W, aušinimo tipas: oras, bendras svoris: 45 kg, aukščio reguliavimo tipas: elektrinis, nuskaitymo srities ilgis: 110 mm, nuskaitymo srities plotis: 110 mm, lazerio bangos ilgis: 1 064 nm, aplinkos temperatūra (min.): 15 °C, aplinkos temperatūra (maks.): 35 °C, The LAS 22 is a compact desktop unit with a small working area, ideally suited for marking small parts. Due to its compact design, the system is highly practical and can be used virtually anywhere. The universally deployable LAS 22 laser marking system from Systemtechnik Hölzer GmbH is suitable for a wide range of marking applications. With the integrated fiber laser, you can mark almost all materials, such as steel, hard metal, aluminum, and plastics. Depending on requirements, the system can be equipped with either a 20-watt or 30-watt fiber laser. The use of lasers for permanent markings is essential in many industries. The powerful laser software allows you to create texts, numbers, 2D codes, QR codes, and logos with just a few clicks and without requiring extensive programming knowledge. Serial and item numbers are automatically incremented by the software following a prior setup. Additionally, the software can read data (variable information such as drawing numbers, project names, etc.) from existing tables and automatically transfer them to predefined fields. Use of a handheld scanner is also possible. Standard equipment includes a laptop with Windows operating system and laser software. Optionally, the LAS 22 can be fitted with a rotary axis (3-jaw chuck) for marking cylindrical parts. - 30 Watt fiber laser (optional: 20 Watt) - Laser class 1 - Wavelength 1064 nm - Marking area size 110 x 110 mm - EZCAD marking software in German / English - Pilot laser (simple preview, contour preview) - Focus finder (easy focusing) - Max. part height approx. 95 mm - Grid holes for fixtures - Clamping area 310 x 190 mm - Electrically adjustable Z-axis - Electrically operated door with clamp protection stop - Optional: exhaust system (including activated carbon filter) - Welded steel sheet construction Rcsdpfouy H Nqsx Acaed - 230V connection - Air-cooled - Laptop with Windows operating system (German or English) - Dimensions (LxWxH): 600 x 400 x 690 mm - Weight: approx. 45 kg

Būklė: visiškai atnaujintas (naudotas), mašinos/transporto priemonės numeris: 4507, Centerless grinding machine ESTARTA 327 Rcodpeg Ix Hmefx Acaod

Gamybos metai: 2026, būklė: beveik kaip naujas (parodų įrenginys), Parts Washing Machine / Spray Cleaning System Type TR450 The Spray-Rotation Cleaning System Type TR450 is an automatic cleaning and degreasing unit featuring an easy-to-open upward swinging lid. This system is designed for cleaning individual parts and/or bulk material in baskets sized LxWxH 520x320x200h mm. During the cleaning process, the basket must be closed with a lid. The cleaning result depends on allowing slight circulation of bulk material inside the basket, which requires attention to the fill level in the basket. The system is additionally equipped with a flooding tray beneath the goods basket, enabling flood scooping of the parts for an even more effective cleaning outcome. Equipment includes: • Complete inside and outside stainless steel construction (grade 1.4301) • Level monitoring and automatic freshwater refill • Full system insulation Rjdpfjfbt Siex Acascd • Hot air drying (output: 11.6 kW) • Steam fume extraction • Oil skimmer for bath maintenance • Automatic freshwater refill • 1 small parts basket, 520x320x200h mm, mesh size: 6x6 mm, incl. height-adjustable clamping lid Power supply requirement: approx. 20 kW (32 amp plug)

Būklė: beveik kaip naujas (parodų įrenginys), Gamybos metai: 2026, Parts Cleaning Machine, Spray Cleaning System Type L800FP Rcodpouxuv Aefx Acasd Fully automatic hot water parts washing machine with basket drive powered by gear motor, housing made of stainless steel 1.4301, piping and rotary basket galvanized steel, special nozzle system with stainless steel flat jet nozzles, wash pump made of stainless steel (manufacturer: Xylem/Lowara), level control for dry-run protection, - Basket diameter: 780 mm - Effective height: 500 mm - Max. load capacity: 150 kg - Spray pressure: 3 bar - Tank volume: 120 liters - Heating: electrically adjustable (room temperature up to 60°C) System dimensions (LxWxH): 1,160 x 1,200 x 1,750 mm Suction filter for pump protection Delivery: ex works, FCA

Būklė: naujas, Gamybos metai: 2026, Parts Cleaning Machine, Spray Cleaning System Type L800FP Fully automatic hot water parts washing machine with basket drive powered by gear motor, housing made of stainless steel 1.4301, piping and rotary basket galvanized steel, special nozzle system with stainless steel flat jet nozzles, wash pump made of stainless steel (manufacturer: Xylem/Lowara), level control for dry-run protection, - Basket diameter: 780 mm - Effective height: 500 mm - Max. load capacity: 150 kg - Spray pressure: 3 bar - Tank volume: 120 liters - Heating: electrically adjustable (room temperature up to 60°C) System dimensions (LxWxH): 1,160 x 1,200 x 1,750 mm Rsdpfohl H Ubex Acascd Suction filter for pump protection Delivery: ex works, FCA

Būklė: naujas, Techniniai duomenys: Darbinis ilgis: 1020 mm Maks. lakšto storis: 2,5 mm Maks. atidarymo plotis: 48 mm Lankstymo kampas: 0 - 135° Plotis: 1350 mm Gylis: 820 mm Aukštis: 1140 mm Svoris apytiksliai: 285 kg Savybės: - Universalus lankstymo aparatas, tinkantis tiek skardininkystės dirbtuvėms, tiek remonto įmonėms - Tvirta konstrukcija modernesnio dizaino - Lengvas viršutinio spaustuvo reguliavimas kojiniu pedalu, rankos laisvos ruošiniui - Rankinė lankstymo staklės standartiniams lankstymo darbams Rjdsct Rzbjpfx Acajcd - Segmentuotas viršutinis spaustuvas suteikia daug lankstymo galimybių - Puikus kainos ir kokybės santykis - Greitas ir paprastas lenkimo procesas per lanko rankeną - Neslystantis guminis pedalo paviršius saugesniam darbui - Paprastas apatinio spaustuvo sureguliavimas pagal lakšto storį - Aukštas viršutinis spaustuvas – patogu gaminti didelio aukščio kampinius profilius

Gamybos metai: 2026, būklė: naujas, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 2026, NAUJA NAUJA Indaplovė NAUJA NAUJA Rodpfx Acjvdkuhjaecd Nerūdijančio plieno konstrukcija su LCD ekranu Galinga ir universali indaplovė 2, 3 ir 5 min. plovimo trukmė 1 lėkščių krepšys, 1 universalus krepšys ir stalo įrankių laikiklis Našumas apie: 30 krepšių/val. / 540 lėkščių Indaplovė su išleidimo siurbliu Ploviklio ir skalavimo priemonės dozatorius Tik pas mus: patikrinta pagal DGUV V3 Jungtis: 400V, 16A-CEE kištukas Matmenys: 600 x 600 x 820 - 850 mm, PlxGxA NAUJA mašina su garantija + atsarginių dalių servisu Sandėlyje turime daugiau puikių indaplovių!

Būklė: beveik kaip naujas (naudotas), Gamybos metai: 2023, Mandrel Bending Machine S4501 ----- For the production of tube geometries with bending radii starting from 1.5xD → Maximum bending capacity (tube): 42.4 x 3.25 mm (steel, max. Re 240 N/mm²) → Maximum bending capacity (tube): 30 x 30 x 3 mm → Maximum bending capacity (tube): 42.4 x 2 mm (stainless steel, 0.2 260 N/mm²) → Total connected load: 3 kW → Tube feed-in length: approx. 1.5 m Robust and durable steel construction. Maintenance-free servo drive for the bending, feed, and rotation axes. The touch display controller allows for easy and intuitive programming and operation of the machine. After the tube is inserted, it is fixed by the chuck in the carriage, ensuring precise tube positioning and highly accurate geometry production. Standard features also include pre-bending geometry control: if the bend is initiated at the wrong position, the system blocks the process, thereby preventing operator errors. Optional additional features increase convenience, output, and overall system efficiency. Data exchange with the optional TBS-3D tube calculation software (PC version) is via USB stick or network. Existing tube geometries can be imported with the software. Rcjdjtr U Hlepfx Acaod Standard equipment: → Servo drive for bending axis, 1.5 kW → Adjustable rotation speed → Left bending direction → Bending angle resolution 0.1° → Max. bending radius 120 mm → Bending shaft diameter 50 mm → Servo drive for feed → Servo drive for rotation → Three-jaw chuck for tube fixation in the carriage → Pneumatic tool retraction Hydraulics: → Hydraulic tube clamping with adjustable clamping pressure → Programmable early mandrel retraction PLC Control: → 10" colour touchscreen → ETH 10/100, X2X Link, 2x USB → Foot switch operation → Data transfer via LAN or USB → Material database Unique graphical programming: simple geometries can be calculated directly on the machine. After entering length and angle, the control calculates feed and bending angles automatically. Power supply: 400V 16A Dimensions: L:2.3m x W:1m x H:1.4m Weight: approx. 1200 kg