Ilgio profiliuotojas

JOEMA 450

Sąlyga: naudotas, Gamybos metai: 2001, Wood dimensions to be processed: Incoming lengths min/max: 500 – 6500 mm; Full optimization up to max. 1500 mm. Incoming widths min/max: 40 – 300 mm. Incoming thicknesses min/max: 15 – 120 mm. Maximum wood cross-sections: 300 x 40 mm, max. 200 x 120 mm. Fixed lengths after saw: min. 510 – 2800 mm. Special application: Cutting of blocks, length min/max: 100 – 200 mm (Note: multiple block length during sorting, blocks are transported to the end of the sorting line and drop into customer-side mesh boxes). Cut/trimming tolerance: +/- 0.8 – 1.5 mm (for wood with minimum resin content and even surface. Tolerance up to 1 m fixed length, max. tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm. Curvature of wood in all directions: max. 10 mm per meter length. Types of wood: Softwood or hardwood. Machine performance: Feed speed continuously adjustable up to max. 230 m/min; cutting cycle 0.6 – 1 s. To determine the practical daily output, an effectiveness factor dependent on the customer’s production conditions must be considered. Infeed and saw working height: 900 mm (install required on customer-side platform, saw requires concrete base). Sorting working height: 2000 mm. Connection values: Total electrical connection load approx. 18 kW. Operating voltage: 380 Volt / 50 Hz. Voltage fluctuations max. 5 %. Air consumption approx. 1200 NL/min. Operating pressure approx. 8 bar. Extraction velocity approx. 30 m/s. Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B. POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge. Pos. 2: Support roller without drive, at the end before steel table for easier feeding. Blodpfx Adsw Sy T Hewod Pos. 3: Length measuring station with built-in fluorescence camera for detecting defect markings. Pos. 4: Automatic non-contact width measurement. Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with built-in waste chute incl. equipment package for large wood cross-sections. Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and plant control. The following are available for processing: - max. 16 product groups - max. 8 qualities per product group - max. 200 fixed lengths per product group. Pos. 6: Discharge conveyor belt as sorting station with drive unit, length 7500 mm. Pos. 7: 2 ejectors mounted on discharge conveyor belt. Location: Nattheim

Sąlyga: naujas, Gamybos metai: 2022, Funkcionalumas: visiškai funkcionalus, Naujas Friulmac EQ 004 2.5 su padavimo konvejeriu ir padavimo bunkeriu Valdymas liečiamu ekranu ir automatinis reguliavimas Darbinis ilgis: min 190 mm – maks 2500 mm Plotis: min 30 mm – maks 250 mm Storis: min 12 mm – maks 35 mm Greitis: 6–25 m/min 2 x 2 Viršutinis velenas – 3 kW – 720 aps./min. Blsdovupm Depfx Adwsd Pagrindinis profiliavimo velenas – 4 kW – 7200 aps./min. Dėl išsamesnės informacijos galiu atsiųsti originalią dokumentaciją.

Sąlyga: naujas, mit Hobelwelle Typ: R-R-RP1300 Arbeitsbreite: 1300 mm Min. Werkstücklänge: 538 mm Arbeitshöhe: 3–110 mm Vorschubgeschwindigkeit: 6–30 m/min Gesamtmotorleistung: 77,12 kW Motorleistung 1. Aggregat: 22 kW Motorleistung 2. Aggregat: 30 kW Bljdod H Sc Eopfx Adwjd Motorleistung 3. Aggregat: 18,5 kW Schleifbandabmessung: 1330 x 2200 mm Betriebsdruck: 0,55 MPa Absaugleistung: 12.000 m³/h Transportabmessungen: 3090 x 2020 x 2260 mm Gewicht: 4.700 kg

Sąlyga: beveik kaip naujas (naudotas), Gamybos metai: 2023, veikimo valandos: 990 h, Funkcionalumas: visiškai funkcionalus, įvesties srovės tipas: trifazis, bendras aukštis: 3 900 mm, įėjimo srovė: 63 A, bendras ilgis: 9 500 mm, bendras plotis: 4 500 mm, galia: 15 kW (20,39 AG), Įranga: dokumentacija / vadovas, Pelletizing plant suitable for a wide range of materials such as wood, miscanthus, agricultural by-products and waste (hay, straw, corn straw, etc.), as well as feed materials. This is a complete system mounted on a base frame and consists of the following components: - Raw material storage container, 4m³, including agitator. This has been extended with wooden panels to approximately 3-4m³. - Intermediate screw conveyor to the hammer mill - Hammer mill, 11 kW, for shredding wood chips or other materials - Inclined mixer for material homogenization including moisture measurement, dosing unit, and level monitoring - Dosing container for press additives, feeds into the inclined mixer - Dosing screw for optimal material feeding to the pellet press (speed controlled) - Pellet press, 15 kW, including full sensor, temperature monitoring, and discharge chute Bsdjxv Dkcspfx Adwjld - Conveyor belt to the dedusting sieve - Dedusting sieve with material discharge at 3m height The plant is designed for easy expansion with a second 15 kW press. The entire system is centrally controlled via a Siemens PLC with touch display. All operating parameters are monitored, and the press will shut down automatically in the event of a fault. Remote operation and monitoring of the press is possible via any PC. The chip dryer shown on picture 2, mounted on the wall with discharge and control system, can also be purchased. For further details, please contact us.

Sąlyga: beveik kaip naujas (naudotas), Gamybos metai: 2022, veikimo valandos: 500 h, Funkcionalumas: visiškai funkcionalus, Drying paternoster for finger-jointed boards Consisting of: - Transfer chain after the finger-jointing press, foldable - Drying paternoster approx. 7 m, for board lengths up to 6 m - Cut-off and zero saw - Conveyor belt for residual wood disposal - Stacking system - Batten magazine not for sale - Package cross conveyor Blsdpewclkyefx Adwed The machine is in very good condition, with very few operating hours. Machine is still assembled, but available immediately.

Sąlyga: labai geros būklės (naudotas), ONE-SIDED DESTACKING STATION - Upper traverse, horizontally shiftable by 180° - Console table with vacuum clamps - Lift table (internal) with motorized sheet metal roller conveyor - Front safety guard, movable - Separate control cabinet and operating panel - External roller conveyor for transporting the stack of sheets from destacking - External driven roller conveyor from destacking, optionally with belt for 90° transfer of sheets - Operating capacity (cycles/min): 12-15 Bsdpfxocggy Ss Adweld - Plate thickness (min/max) mm: 10 - 40 - Min. plate dimensions mm: 250 x 320 - Max. plate dimensions mm: 1200 x 3000 - Total connected load Kw: 10

Sąlyga: geras (naudotas), Gamybos metai: 1989, Funkcionalumas: visiškai funkcionalus, obliavimo plotis: 2 050 mm, aukščio reguliavimo tipas: pneumatinis, obliavimo aukštis: 300 mm, 4-side planer, working width: 2200 mm, mounted on a turntable for curved parts, enclosed machine Bedpsw A A Ebsfx Adwold

Sąlyga: naudotas, Gamybos metai: 2000, Velenų skaičius: 5 vnt. Darbinis plotis: 230 mm Obliavimo aukštis: 160 mm Padavimo variklis: 4 kW Padavimo greitis: 5–24 m/min. Weinig Unimat 23E keturpusio obliavimo ir profiliavimo automatas, skirtas medienai obliuoti ir profiliuoti iš visų keturių pusių, turintis mobilų veleną automatiniam reguliavimui bei griovelių stalą (pasirinktinai be griovelių stalo) trumpiems ir lenktiems ruošiniams bei ilgą lyginimo stalą. Papildomai: Pakeitimas į įprastą lygų stalą pagal užklausą. Bsdpfx Aewztw Sedwold Velenas 1: Apačioje / 40 mm / 5,5 kW Velenas 2: Dešinėje / 40 mm / 7,5 kW Velenas 3: Kairėje / 40 mm / Bendras variklis su 2-uoju velenu Velenas 4: Viršuje / 40 mm / 7,5 kW Velenas 5: Apačioje / 40 mm / 5,5 kW

Sąlyga: geras (naudotas), Gamybos metai: 1999, Briketavimo presas GP 120 Tandem tipas. Presas skirtas pjuvenoms, drožlėms ir dulkėms briketuoti, su automatiniu lygio jutikliu. - Briketo diametras: 60 mm - Presavimo našumas: 40 - 120 kg/h * 2 = 80 - 240 kg/h (priklausomai nuo medžiagos) - Piltuvo atidarymo dydis: apie 1.900 x 1.900 mm - Piltuvo aukštis: apie 1.800 mm - Piltuvo talpa: apie 6,0 m³ - Variklio galia: 7,5 kW, 400 V, 50 Hz - Valdymo spinta: iš abiejų pusių Blsdpfx Adoupwx Hewsd - Darbo valandos: 13.725 val. arba 13.005 val. - Hidraulinis agregatas: apie 300 l hidraulinio aliejaus bakas - Svoris: apie 1.100 kg * 2 = 2.200 kg Naudotas briketavimo presas, geros būklės. W-znyplių cilindras, replės (RB 120 sustiprintos), replės jungties flanšas viena kryptimi pakeistas (kairėje, transportavimo kryptimi) briketavimas | briketavimo presas | briketavimo presai | briketų presas | briketavimas

Sąlyga: geras (naudotas), Artikkel: A-7577 Fløtetank 10 000 L Rustfri prosessfløtetank, dobbelmantlet, isolert, skrapeomrører fra toppen, CIP-montert på toppen. 3 justerbare ben, mannlokk på toppen. Kapasitet 10 000 L. Vi kan tilby 2 stk fra lager. Bodpfsh E Dp Ajx Adwsld Diameter: 2 458 mm.