HUNDEGGER K2, 4 ašys

HUNDEGGER K2 4 assi

Būklė: geras (naudotas), Gamybos metai: 2011, Fully automatic timber infeed with feed roller conveyor Extension of cross conveyor and feed roller conveyor for timber lengths up to 13 m Infeed and loading cross conveyor Under-table swing cut-off saw Universal 4-axis milling unit (UF4) Combination support for vertically operated tools Drilling unit 2.2 kW Combination support for horizontally operated tools Drilling unit 2.2 kW Longitudinal and cross groove milling machine Rear marking device (on the stop side) Fully automatic beam turning station – hydraulic Transport and positioning device "two-hand operation system" Electronic control with EKP software Roller conveyor for timber outfeed incl. extension (without drive) Nsdpjwuppwefx Acpjcr Component ejector 5-arm timber deposit rack Safety devices and protective guards

Gamybos metai: 2011, būklė: naudotas, Funkcionalumas: visiškai funkcionalus, Finger jointing line for cross-sections up to 200 cm² (80/240 mm or 100/200 mm), with the following components: 1. HOWIAL Tilt Destacking Unit - SH/4t - 1.75x1.75x6.00m - 4t – minimum length 2.50 m, semi-automatic package separation. For tilting wood stacks up to 45°. Electrically driven. Maximum stack dimensions 1.75 x 1.75 x 6.00 m, max. stack load 4 t, shortest wood length 2.5 m. 2. HOWIAL Lamella Separator VE 1 for cross-cut saw. With pneumatically controlled fingers for material marked after defect detection, deposited on the underlying roller conveyor. 3. HOWIAL Grading Roller Conveyor RO-1 Digital wood moisture measurement, control and registration system for the automatic detection and control of wood moisture using the electrical resistance method in a cycle-based process. 4. Gann DMT-8 Digital wood moisture measurement, control and registration system for the automatic detection and control of wood moisture using the electrical resistance method in a cycle-based process. System integrated in a large control cabinet, complete with inkjet printer. 5. HOWIAL Cross-Cut Saw AS-30 B Pneumatically controlled under-table cross-cut saw with 2 automatic feed units, automatic cross-cutting. Special photoelectric cell control for detection of fluorescent marking lines. Automatic waste detection possible. Saw motor power 7.5 kW Saw blade diameter 700 mm Feed drive approx. 2 x 1.5 kW Air pressure 8 bar Feed speed max. approx. 60 m/min 6. HOWIAL Conveyor Belt for Cut-Off Waste, with studded belt and guide plates Belt width 350 mm Belt length 2000 mm Belt speed 0.4 m/sec 7. HOWIAL Double Roller Conveyor RO-2, 6.00 m long Incl. cross transfer, equipment for the finger jointing automation. Driven by round belts, all rollers driven. Cross removal via chain conveyor. Ejector ± moisture, right side. Adjustable transport speed 100 m/min. Length approx. 6.00 m Roller width approx. 400 mm Diameter 112 mm 8. Compact Finger Jointing Machine Cook Bolinder Technical data as per Cook Bolinder: Wood width from 75 to 245 mm Wood thickness from 20 to 105 mm Infeed length from 1 m to 6 m Cross-sections from 30 cm² to 200 cm² Pressing force 5 - 22 tons Spindle diameter 50 mm Finger profile 15/15 Spindle speed approx. 6000 rpm Total connected electrical load approx. 62 kW Machine weight approx. 9 tons. OEST comb gluing system for PU adhesives Modern Telemechanique PLC control. Ncodpfx Acoi Ezx Dspjr 9. HOWIAL Roller Conveyor with De-stacking Driven roller conveyor with automatic ejector and hydraulically operated de-stacking arms. Technical data: H: 920 mm L: approx. 12,000 mm 10. Safety Fencing including safety switches 11. Finger Joint Testing Machine BSPLT-100 Testing machine for finger joint bending test according to DIN 1052-1/A1 and EN 385. Support distances freely adjustable, integrated measuring scale, automatic calculation of support distances in software. Fully automatic test sequence via mouse click on PC (not included). Alternatively, test sequence can be triggered from control panel. Connects to any standard PC or laptop (Win 2000/XP) using provided RS232 serial cable. Fully automatic data acquisition and test report generation in MS Excel with graphical presentation. Max. wood width: 300 mm Max. wood thickness: 140 mm Max. pressing force: < 100 kN Max. support length: 2100 mm Measurement accuracy WITHOUT DISASSEMBLY

Būklė: geras (naudotas), Gamybos metai: 1995, Funkcionalumas: visiškai funkcionalus, DARBO MATMENYS: 400 x 250 mm. 4 PUSĖS + KAMPO NUPJOVĖJAI Ncodpex S E Hasfx Acpsr

Būklė: naudotas, Gamybos metai: 2003, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 11441, Šiuo metu dirbame su šia versija: 9.23.12.102733-12 K2 įranga: 4 ašių universali frezavimo staklė, 2 gręžimo staklės, apatinis pirštinis frezuotuvas, griovelio pjovimo staklė, hidraulinė sijos apvertimo stotis Njdpfx Aowvih Ajcpscr Staklė visiškai veikianti, galima apžiūrėti susitarus. Prieinama nuo 2026-05-01. Staklės išardymas ir pakrovimas į sunkvežimį yra įskaičiuoti į kainą. Parduodama kaip naudota staklė be jokios garantijos.

Būklė: labai geros būklės (naudotas), Gamybos metai: 2003, mašinos/transporto priemonės numeris: 11470, Funkcionalumas: visiškai funkcionalus, ruošinio plotis (maks.): 450 mm, Hundegger K2 in very good condition, overhauled, assembled, and commissioned by Hundegger. Since then, it has only run for approximately 20 hours, was professionally dismantled, and has been stored in a heated hall. Ncedswhpavjpfx Acpsr

Būklė: naudotas, Naudota mašina Pagaminimo metai: 1991 Pilnai automatinė, stovima, Pjovimo diapazonas: 5.300 x 2.200 mm (pjovimo plotis x pjovimo aukštis), Pjūklo disko skersmuo: 300 mm, Valdymas vertikaliems ir horizontaliems pjūviams, Ncsdpex Rr D Asfx Acper su ALU atlenkiamais ribotuvais ir ALU vidurine atrama, su SUPER-CUT priešpjovimo įrenginiu Variklis: 3 kW - 400 V Prieinamumas: iš karto Vieta: Röllbach

Būklė: labai geros būklės (naudotas), Gamybos metai: 2018, The line consists of: - WEINMANN OPTIMAT WTZ 120/12 L assembly table - WEINMANN WMS 150 - WEINMANN OPTIMAT WTW 110/12 N/L take-off table - Schmalz Jumbo Ergo 140 tube lifter with vacuum handling system The WMS150 multifunction bridge is a CNC machine for the automated processing of timber structural elements (walls, roofs, and floors) Machine length (X axis): approx. 3,000 mm Machine width (Y axis): approx. 6,200 mm Machine height (Z axis): approx. 3,000 mm Maximum workpiece width: approx. 3,200 mm Main spindle 18.5 kW with automatic tool changer FLEX5 indexing system WMS tool changer set consisting of: - Three-edge roughing universal cutter - Drilling unit - Sawing unit Ncodpoytyuajfx Acpjr - Marker with ballpoint pen technology HSK - Saw unit NL 55 mm HSK63F - Saw unit NL 105 mm HSK63F Gluing system - Holder for PUR gluing unit - Single-component PUR adhesive aggregate (1K) with 6 application nozzles Fastening and assembly unit - Automatic height adjustment for the fastening device - Support for ADUNOX screw driver - ADUNOX-TRS screw-driving unit Bridge extension Tool carrier beam with integrated Y axis U-profile guide rail for the bridge Enhanced drive dynamics on X axis Energy supply via cable chain system End-of-travel monitoring for movement systems Wheel locking and carriage stop on the right side of the gantry Homatic powerControl V2.0 control Remote control for WMS150 with potentiometer Mobile extraction unit 3.0 kW Cooling unit for electrical cabinet Less than 1,000 working hours

Būklė: paruoštas naudoti (naudotas), Gamybos metai: 1997, Funkcionalumas: visiškai funkcionalus, mašinos/transporto priemonės numeris: 1779, K1 buvo perstatyta 2020 metais ir aprūpinta šiuolaikinėmis saugos priemonėmis. Šiuo metu įrenginys yra išardytas, laikomas lauke po danga ir gali būti nedelsiant pakrautas. Ncodpex Ehmaefx Acper

Būklė: labai geros būklės (naudotas), Gamybos metai: 2018, Funkcionalumas: visiškai funkcionalus, Double table machining center Working area X: 2,590 mm Nsdsuqw E Nepfx Acpocr Working area Y: 2,260 mm Working area Z: 400 mm Number of milling spindles: 2 Spindle with liquid cooling Main motor: 19.2 kW Max spindle speed: 24,000 rpm Aggregate heads 4th axis: C-Axis Tool clamping system: HSK-F63 Central tool changer magazine: 24 positions Tool changer on each head: 12 positions Vertical drilling heads: 20 (per head) Horizontal drilling bits X: 8 Horizontal drilling bits Y: 8 Grooving saw in X and Y directions 2 tables Number of vacuum pumps: 4, each 360 m³/h T-Jet chip blowing system Nesting Manual labeling Barcode reader Tool length measurement Software: BIESSE BIESSEWORKS ADVANCED, BIESSE B_NEST Weight: 17,900 kg

Būklė: naudotas, mašinos/transporto priemonės numeris: 005289, Darbinis plotis X ašis: 7400 mm Darbinis plotis Y ašis: 1550 mm Darbinis paviršius: Nestingo stalas Pagrindinio veleno galia: 11 kW Kontroliuojamų ašių skaičius: 4 ašys Ncjdpfowcyacsx Acpsr Gręžimo velenų skaičius: 10 Įrankių pozicijų skaičius: 14