RANKINĖ PIRŠTŲ SĄNARIŲ LINIJA

EUROTECK ITALIA FJ-2000

Sąlyga: naudotas, Gamybos metai: 2001, Wood dimensions to be processed: Incoming lengths min/max: 500 – 6500 mm; Full optimization up to max. 1500 mm. Incoming widths min/max: 40 – 300 mm. Incoming thicknesses min/max: 15 – 120 mm. Maximum wood cross-sections: 300 x 40 mm, max. 200 x 120 mm. Fixed lengths after saw: min. 510 – 2800 mm. Special application: Cutting of blocks, length min/max: 100 – 200 mm (Note: multiple block length during sorting, blocks are transported to the end of the sorting line and drop into customer-side mesh boxes). Cut/trimming tolerance: +/- 0.8 – 1.5 mm (for wood with minimum resin content and even surface. Tolerance up to 1 m fixed length, max. tolerance for longer parts up to 2.5 m). Thickness tolerance: +/- 3 mm. Curvature of wood in all directions: max. 10 mm per meter length. Types of wood: Softwood or hardwood. Machine performance: Feed speed continuously adjustable up to max. 230 m/min; cutting cycle 0.6 – 1 s. To determine the practical daily output, an effectiveness factor dependent on the customer’s production conditions must be considered. Infeed and saw working height: 900 mm (install required on customer-side platform, saw requires concrete base). Sorting working height: 2000 mm. Connection values: Total electrical connection load approx. 18 kW. Operating voltage: 380 Volt / 50 Hz. Voltage fluctuations max. 5 %. Air consumption approx. 1200 NL/min. Operating pressure approx. 8 bar. Extraction velocity approx. 30 m/s. Paint finish: pebble grey RAL 7032 and blue NCS 5030-R 80 B. Blsdpfx Aaow Sy T Hjhed POSITION OVERVIEW: Pos. 1: Infeed and marking station with 1 adjustable side support table, 1 table as stop edge. Pos. 2: Support roller without drive, at the end before steel table for easier feeding. Pos. 3: Length measuring station with built-in fluorescence camera for detecting defect markings. Pos. 4: Automatic non-contact width measurement. Pos. 5: Optimizing cross-cut saw OptiCut 304 – right-hand version with built-in waste chute incl. equipment package for large wood cross-sections. Graphic-capable input terminal (16 x 40 characters, numeric keypad) with software package for optimization and plant control. The following are available for processing: - max. 16 product groups - max. 8 qualities per product group - max. 200 fixed lengths per product group. Pos. 6: Discharge conveyor belt as sorting station with drive unit, length 7500 mm. Pos. 7: 2 ejectors mounted on discharge conveyor belt. Location: Nattheim

Sąlyga: naudotas, Gamybos metai: 2009, max. workpiece length 4500 mm Milling spindle: 1 unit Main motor: 20 kW Control system: Siemens Weinig Conturex 2 C 114 ----- Working width: 40–260 mm Working height: 25–110 mm 2 x PowerGrip clamping tables, each 2280 mm ----- Workpiece length: 200 – 4,500 mm Machining of workpieces longer than 2,700 mm is carried out using a shuttle cycle. Main spindle 1: ----- Motor with brake, 20 kW HSK 63F Electronically adjustable speed: 2,000–18,000 rpm Maximum tool length from HSK 63 F reference surface: 290 mm With C-axis Tool magazine: ----- Number of slots: 30 Slot spacing: 100 mm Multi-spindle boring unit permanently installed ----- for horizontal and vertical drilling and milling without tool change ----- Price ex location Prices for Dismantling and loading onto customer truck Transport within Germany and abroad, reassembly, commissioning, and if required, new profiles available on request! Bedpfowunwyex Aahsld Including used tools (drawings available on request!): ----- Wood: IV 68, 78, 88 inward and outward opening, with fitted drip rail Wood-aluminium: IV 68/68, 78/78, 87/68, 97/78 Lift/slide doors IV 68 and 78 Entrance doors IV 68 and 78 Pivoting windows Corner joint: counter/dowel Technical data as per manufacturer – without guarantee! Detailed technical description available on request!

Sąlyga: labai geros būklės (naudotas), Line for door frames (casings), for cutting, milling of strike plates, and inserting hinges (ANUBA) comprising: X10030A) Discharge conveyor X10030B) Transfer unit X10030C) Double cutting and drilling machine "AMS" Bljdpjqwycljfx Aahsd - 45° left-side cut – Drilling - 90° cut - 45° right-side cut – Drilling X10030D) Angle conveyor (90°) X10030E) Anuba hinge insertion machine "MASTERWOOD" model MULTITEC X10030F) Strike plate milling machine "MASTERWOOD" model Teknomat 3000

Sąlyga: beveik kaip naujas (naudotas), Gamybos metai: 2022, veikimo valandos: 500 h, Funkcionalumas: visiškai funkcionalus, Drying paternoster for finger-jointed boards Consisting of: - Transfer chain after the finger-jointing press, foldable Bedpfjwclkysx Aahjld - Drying paternoster approx. 7 m, for board lengths up to 6 m - Cut-off and zero saw - Conveyor belt for residual wood disposal - Stacking system - Batten magazine not for sale - Package cross conveyor The machine is in very good condition, with very few operating hours. Machine is still assembled, but available immediately.

Sąlyga: naudotas, Gamybos metai: 2021, pjūklo disko skersmuo: 800 mm, sukimosi greitis (min.): 1 450 aps./min, galia: 5,5 kW (7,48 AG), Chop Saw AS Very good, well-maintained condition Blsded Szf Nspfx Aahsd Saw blade diameter: 800 mm. Robust steel tube frame. High-performance saw motors. Pneumatic material clamps (3 pcs., vertical). Two-hand safety operation. Coolant system. Protective cover. Optionally with length measuring system or automatic positioning system. Available as a saw-drilling or saw-punching automatic machine on request.

Sąlyga: naudotas, Gamybos metai: 2001, Spindle tilt: Yes, -25° to +45° Height adjustment: electric Tilting adjustment: electric Fence jaw adjustment: manual Milling fence jaws: Aigner Integral 600mm Height display: digital Tilting angle display: digital Milling fence position indicator: Siko counter Bjdpfxowx Nnbe Aahjld Spindle diameter: 30 mm Preselectable speeds: 1,500/3,000/4,000/4,500/5,000/6,000/8,000/9,000/10,000 rpm Motor power: 7.5 kW Motor brake: yes, automatic Power feed: Wegoma, 4 rollers Extraction connection: 2 x 120 mm Machine length: 1,900 mm Machine depth: 1,400 mm Weight: 1,000 kg

Sąlyga: geras (naudotas), Gamybos metai: 1996, Four-Sided Planer Weinig Unimat 23 – German-made – Serrated table – Year of manufacture: 1996 – Driven feed rollers in the table TECHNICAL SPECIFICATIONS: Planing width: 230 mm Planing height: 160 mm Serrated table Spindle diameter: 40 mm 1st bottom spindle: 7.5 kW 2nd right spindle: 7.5 kW 3rd left spindle: 7.5 kW 4th top spindle: 11 kW 5th bottom spindle: 7.5 kW Infinitely variable feed speed: 6–36 m/min Feed motor power: 5.5 kW Six upper steel feed rollers Two upper rubber feed rollers Three driven rollers in the table Pneumatic feed pressure Pneumatic pressure shoe Spindles with brakes Infeed table length: 1970 mm Electric height adjustment Bjdpfjh Dwl Dox Aahsld Centralized (split) lubrication Extraction port diameter: 140 mm Machine dimensions (L/W/H): 410 / 200 / 180 cm Weight: approx. 3000 kg

Sąlyga: naudotas, Mechanical nailer by Wursten & Dietz. Prepared for nailing ice skates. The machine is being sold as is. Bedjlvripjpfx Aaheld

Sąlyga: visiškai atnaujintas (naudotas),

Sąlyga: geras (naudotas), Gamybos metai: 2014, Presă de peleți Bledpsvdrtxofx Aahed Producător - TEKNO UNO Model - TK 304 An de fabricație - 2014 Putere motor - 50 kW Capacitate - 450 kg/h