CENTURO R800 + RVP-210 pjovimo pjūklas

Centauro R800 + RVP-210

Sąlyga: naujas, Gamybos metai: 2024, A versatile saw for cutting wood into veneers, slats, and similar materials. Workpiece height up to 400 mm. The powerful feed rate enables very high productivity. The R800 is a robust saw. It can accommodate bands of various widths. It features a mechanical feed system for the workpiece and is designed to perform reliably under heavy main motor load and high processing speeds (up to 30 m/min). A band width of up to 80 mm is possible. The machine's sturdy frame is constructed from welded sheet steel. Massive cast iron flywheels ensure maximum efficiency, and the wheels are mounted on dustproof ball bearings. The lower section of the saw blade is specially reinforced, allowing for a higher level of inertia without excessive startup or braking loads. To further enhance smooth operation, the guides are specially ground to ensure precise balancing. Wheel diameter: 800 mm Max. cutting height: 400 mm Max. cutting width: 770 mm Table height from floor: 960 mm Table size: 1060 x 800 mm Blade length: 5530/5380 mm Max. blade width: 80 x 0.8 mm Motor: 11 kW (15 HP) Flywheel speed: 680 RPM Blade speed: 28.5 m/sec Extraction: 1 x Ø 100 mm, 2 x Ø 120 mm Required extraction capacity: 3840 m³/h Compressed air consumption: 60 L/min Operating pressure: 6 - 8 bar Net weight: 880 kg RVP210 Ndodpfxogp I U No Abaed Roller height: 50 mm Drive roller diameter: 200 mm Standard towing rollers: 2 pcs Standard roller square height: 300 mm Roller square length: 600 mm Roller square tilt: 0-45° Maximum roller-blade opening: 200 mm Maximum square blade opening: 420 mm Motor power: 0.37 kW Variable feed speed: 0-30 m/min Compressed air consumption: 30 L/min Operating pressure: 3 - 6 bar Net weight: 180 kg

Sąlyga: naujas, Gamybos metai: 2025, Working width: 600 mm Working height: 220 mm Minimum workpiece length: 250 mm Units: 4 1. Saw-cut unit Random System: Saw-cut finish 2. Brush: Metal, diameter 220 mm 3. Brush: Tynex grit 60, diameter 220 mm 4. Brush: Tynex grit 120, diameter 220 mm Height adjustment: Handwheel Height display: Mechanical counter Feed speed: 4 - 12 m/min Nodpfehwrp Rjx Abaedd Sawing unit motor power: 1.1 kW Brush motor power: 4 kW Feed motor power: 0.37 kW Machine length: 2800 mm Machine width: 1500 mm Machine height: 1600 mm Weight: 1500 kg

Sąlyga: naujas, Gamybos metai: 2025, Semi-automatic optimizing crosscut saw with electronic positioning system, featuring push/stop mode. COST-CUTTING OPTIMIZER Superpush 150 is an entry-level cutting and optimizing center. Developed as a direct technological evolution of traditional cutting methods, it is designed to increase productivity and improve wood yield. Ndedpfxjg Hzvgo Abasd EXTREMELY ROBUST Constructed entirely of thick, reinforced painted steel. Horizontal table with movable safety guard for easy loading of workpieces. Carriage functions as both a length stop and pusher. Linear unit with toothed belt reinforced with internal steel inserts and linear guides with ball bearings. Continuous horizontal outfeed table with a width of 300 mm. TECHNOLOGICALLY INNOVATIVE Electronic system featuring a touch-screen control panel with integrated CNC. Custom-tailored Linux-based software interface. 15.6” color display, resistive touch screen, ensuring safety in industrial environments. Program import via USB. Remote tele-service via internet. + Excel Macros support. FAST S4U Lite software. Brushless positioning motor with digital servo drive. Rapid selection interface for Stop/Pusher mode. Adjustable cutting speed. RELIABLE AND SAFE Ball-bearing linear guide with double dust protection. Freestanding, separate electrical control cabinet. Independent pneumatic adjustments to accommodate various processing requirements. Two-hand safety cutting control. CE-certified machine by official Certifying Body (not self-certified).

Sąlyga: labai geros būklės (naudotas), Gamybos metai: 2020, The machine is in very good condition, has seen little use, and comes with full equipment. Additionally, 20 saw blades included in the set. SPECIFICATION: WRAVOR BAND SAWMILL TYPE 1225 AC (angled cutting) Max. log width: 1250/1090 mm Max. cutting length: 8 m Main motor: 45 kW Cast wheels Cast wheel width: 130 mm Wheel diameter: 1200 mm Raising/lowering – double screw TR60x9 (18) + 11 kW Danfoss inverter + Siemens 3-phase brake motor Electric motor for raising/lowering: 11 kW Blade PV 45 length: 8685 mm, thickness: 1.2 mm, width: 140/150 mm Feed drive with electronic solutions for blade forward/back – SEW reducer with flat asynchronous controller KA87 / GDRL100L 4BE5 / TF / ES7S / V Manual-sensor adjustment of cutting thickness with electric shut-off Digital cutting thickness adjustment with Wravor V280 program Hydraulic unit 40 L, tank with two pumps 13+6 L + 3 kW motor Complete hydraulic system Hydraulic blade guide left and right HIWIN LINEAR Hydraulic pre-cutter / bark scoring cutter: 1 Hydraulic board ejector: 1 Additional hydraulic board ejector and guider Side-mounted control panel Multifunctional joystick with 2 positions: 1 Multifunctional joystick with 4 positions: 1 Laser: 15 mW Cameras: 3 Fan: 2.2 kW + 15 m sawdust duct + 4 pipe supports Water cooling – automatic cooling hydrofor (Aki Tech high-pressure pump): 1 Preparation for ramp and automatic table + spreader: 1 Diesel greasing TRACK Welded construction, 14 m length Hydraulic clamp with two cylinders: 6 Hydraulic log turner: 6 Mechanical supports: 2 Hydraulic roller – forward: 6 Hydraulic log lifter on brackets – mechanical roller: 4 Hydraulic log lifter on brackets – hydraulic roller: 7 Set of lifting cylinders: 7 hydraulic + 4 m: 1 Hydraulic turner – new type: 3 Centering device – 1 set: 4 Hydraulic unit 120 L, tank with one pump 50 L, motor 15 kW + Danfoss inverter: 1 Cable carrier with energy chain: 14.5 m C-profile carrier for ventilation – 4 double trolleys Belt discharge conveyor 4 m with 1 m feed segment + Njdpfx Asw E Ei Uobajdd electric motor 3 kW, front section with hydraulic lift

Sąlyga: beveik kaip naujas (naudotas), Double-shaft multirip saw A. COSTA PUMA 2/50 350/160 – Italian manufacture TECHNICAL PARAMETERS: cutting width: 350 mm cutting height: 160 mm motors: 37 and 45 kW feed motor: 3 kW lower shaft width adjustment maximum blade diameter: 280 mm spindle diameter: 2 x 60 mm sleeve diameter: 2 x 80 mm track width: 350 mm total power: 85 kW two feed speeds: 15 and 22 m/min central lubrication minimum workpiece length: 600 mm electric height adjustment top and bottom shaft height adjustment six upper pressure rollers mechanical roller pressure town anti-kickback pawls cast iron frame extraction port diameter: 2 x 220 mm spindle speed: 4500 RPM machine dimensions (L/W/H): 250 / 235 / 210 cm weight: ~ 5000 kg Njdpfxsqy E Rle Abajdd

Sąlyga: geras (naudotas), Gamybos metai: 1996, KRÜSI Chalet Construction Machine / Log House Production Line Type CM 40 Manufacturer: Krüsi Maschinenbau AG, CH-9105 Schönengrund AR Year of manufacture: 1996 Condition: Good, technically inspected and cleaned / ready for operation Operating principle Processing of timber for chalet construction / log house production. Beams can be processed in a single pass. • Cross-cutting • Horizontal and vertical milling of notches/grooves in a single clamping • Drilling • Milling of end grooves Workpiece: • Max. cutting height: 200 mm • Max. cutting width: 250 mm Rugged welded steel construction. Machine (horizontal and vertical milling units) equipped with 4 special milling motors, hardened and ground guides for maximum processing accuracy. Carriage guided by dust-protected, preloaded ball bearing guide rollers. Ndsdpfou Uh T Dox Abaed Working range up to 200 x 250 mm. Fully operational, with contactor control system; motors protected by thermal relays. Electrical equipment for 380 V, 50 Hz, with protective covers, central connection for customer-provided chip extraction system; includes 2 eccentric clamps; no milling tools (rebate cutter). Features electro-hydropneumatic horizontal and vertical feed, synchronized with the start of the milling motors. Rapid traverse and feed rate steplessly adjustable. Fully wired and installed, including air service unit. Beams thicker than 14 cm must be processed in two passes; for these beams, the workpiece must be fed again to the extent of the excess thickness for further milling. Machine guards over all moving parts with gas spring counterbalance. Machine description / equipped with: 1. Saw unit: Manual feed Spindle adjustment with analog scale display Max. saw blade Ø / bore Ø: 400 / 30 mm Tungsten carbide tipped with chip depth limiter (uni-directional) Adjustable riving knife Motor speed min⁻¹: 2900 Power (kW): 2.2 2. CM milling unit (log house unit): Hydropneumatic feed Spindle adjustment with digital scale display Horizontal milling unit: Cutter Ø: 180 mm Max. cutter width: 130 mm For cutter width >60 mm only use aluminum alloy cutters with indexable inserts. 2 x hydropneumatic feed motors, each 2.2 kW Hydropneumatic feed; rapid traverse and working feed rate steplessly adjustable. 3. Drilling unit: Manual feed Spindle adjustment with analog scale display Drill chuck: ER 25 collet Max. clamp Ø: 16 mm Max. drill Ø: 32 mm Motor speed min⁻¹: 1450, Power (kW): 1.8 4. End milling unit: Hydropneumatic feed Spindle adjustment with digital scale display Max. cutter Ø: 230 mm Max. cutter width: 60 mm Motor min⁻¹/2900, 3.0 kW 2 V-belts SPZ 9.5x1000 La Pneumatics Required operating pressure min/max. MPa (bar): 0.7/1 (7/10) Air consumption: 8 Nm3/h Electrics Operating voltage V/Hz: 380 V, 50 Hz Rated power: 8.8 – 15.8 kW depending on configuration Customer-supplied fuse: 3 x 25 A (slow-blow) Max. simultaneous power demand: 4.4 kW Dimensions Machine width: 2400 mm Machine depth: 1600 mm Total height, guard lowered: 1600 mm Total height, guard raised: 2200 mm Extraction port Ø (under-floor extraction) Weight: approx. 1300 kg Including roller conveyor 2 x 6 m (2 x 4 m) Technical data subject to change!

Sąlyga: naujas, Power Feeder - 4 rollers - Roller diameter: 120 mm Ndedoh Dikwepfx Abaod - Roller width: 60 mm - Motor power: 0.75 kW - Pole-changeable motor - Speed: 1,400 rpm - Feed speed: 3 – 18 m/min, variable - Approximate weight: 37 kg WITHOUT stand ‘Standard’ or ‘1050’ stand optionally available Notice for Used Machines: • Technical information is subject to error and prior sale. • Prices quoted are ex-works and include loading! • The machine has been cleaned and function-tested. • All machines are sold as seen without any warranty whatsoever. Buyers are free to inspect the machines at our location. • Special agreements are valid only in written form. (We only respond to inquiries that include your address and telephone number!)

Sąlyga: geras (naudotas), pjovimo aukštis (maks.): 200 mm, grandis plotis: 400 mm, įėjimo įtampa: 380 V, aukščio reguliavimo tipas: elektrinis, sukimosi greitis (maks.): 3 400 aps./min, galia: 37 kW (50,31 AG), Maksimali darbinė aukštis: 200 mm Grandinės plotis: 400 mm Maksimalus atstumas tarp išorinių peilių: 380 mm Peilių skersmuo (min./maks.): 250 / 350 mm Reguliuojamas padavimo greitis (su inverteriu): 5–30 m/min Mažiausias ruošinio ilgis: 1000 mm Peilio laikiklio skersmuo: 70 mm Ndjdpetvpfmjfx Abasd Peilio laikiklio veleno apsukos: 3 400 aps./min. Variklių galia: 2 x 37 kW

Gamybos metai: 1999, Sąlyga: naudotas, The DSG 200 vertical sawmill is the ideal option for woodworking facilities specializing in furniture and wooden flooring production; it is efficient and performs reliably in operation. A used Wintersteiger mini sawmill is a very sound investment. A major advantage of this machine is that it does not take up as much space as standard equipment of this type, while still excelling in material processing. It is used for cutting individual elements and matching them to the desired sizes. The machine is easy to operate and can be mastered quickly. The greatest asset of our sawmill is its extensive equipment, featuring primarily a blade spraying system controlled from the panel, enabling precise cutting of wet material. It features independent adjustment of the upper rollers’ height, allowing for quicker cutting height settings. Pneumatic feed pusher assists the feed process. TECHNICAL DATA: -Total power: 27.3 kW -Air Jet system motor: 2.3 kW -Siemens control panel -Feed rate up to 2 m/min -Sawmill frame stroke: 210 mm -Strokes per minute: 400 -Cutting height: steplessly adjustable (smoothly) on our frame: 45–250 mm -Maximum achievable cutting height: 400 mm! -Cutting width under side pressure: 80–205 mm -Minimum block length: 250 mm -Lamella thickness: from 1.5 mm – depending on wood type and cutting height -Kerf for used blades: 0.9–1.1 mm depending on cutting height -Length: approx. 5000 mm -Width: approx. 1300 mm -Height: approx. 2600 mm -Weight: 5000 kg Pneumatic feed pusher assists the feed process The machine is supplied with: -Complete large saw blade frame -Small saw blade frame -Frame pins -Frame tensioning wedges -Blade spacers -Blades for wet cutting -Blades for dry cutting -Set of upper feed rollers -4 lower feed rollers -Set of slides -Frame yokes -Pocket cutting guides -Loading magazines -DTR documentation Ndodpfx Ajtvm Hdjbaod -Electrical diagram

Sąlyga: naujas, Gamybos metai: 2025, Working width: 400 mm Working height: 300 mm Minimum workpiece length: 250 mm Units: 2 brush units, individually adjustable 1st brush: Scotch Brite Medium / Diameter 220 mm, variable speed drive 2nd brush: Scotch Brite Hard / Diameter 220 mm, variable speed drive Height adjustment: Handwheel Height display: Mechanical counter Feed speed: 4 - 12 m/min Ndsdpfxei Hpk Uj Abajd Brush motor power: 2 x 3 kW / both with variable speed drive (infinitely adjustable) Feed motor power: 0.37 kW Machine length: 1400 mm Machine width: 900 mm Weight: 500 kg