Cilindrinė šlifavimo mašina

Kellenberger KEL-VARIA

Sąlyga: naudotas, Cilindrinė šlifavimo staklė KELLENBERGER KEL VARIA CNC #4630 Gjdpfxoxmg Eks Acuebu

Sąlyga: naudotas, Description: Workpiece Spindle Head: Swivel Range: -10°/+100° Speed: 800 rpm Centre Height: 175 mm Internal Taper: MK5 External Short Taper: DIN 55026 Max. Workpiece Weight: 150 kg Grinding Spindle Head: Design: Tandem Grinding Spindle Head B-Axis: -210°/+30° Internal Grinding Unit: Internal Grinding Spindle Grinding Table (X-Axis): X-Axis Travel: 320 mm Max. Traversing Speed: 7.5 m/min Resolution: 0.1 μm Sub-Table (Z-Axis): Centre Distance: 1,000 mm Z-Axis Travel: 1,150 mm Max. Traversing Speed: 15 m/min Resolution: 0.1 μm Equipment / Accessories: Coolant Supply: Coolant System with Filter Emulsion Mist Separator: Mechanical Gsdpfx Ajwz T Azscuobu Tailstock: MK4, stroke 50 mm Workpiece Measurement I: Movomatic TMP 91 Workpiece Measurement II: Movomatic TNU 91 Tool Measurement: Marposs A 90 Setup Mode: Electronic Handwheel Accessories: Various flanges, centres and chucks

Sąlyga: naudotas, Gamybos metai: 2003, Grinding diameter: 450 mm Grinding length: 1500 mm Center height: 225 mm Photos show a nearly identical machine with 1000 mm capacity Also geometrically overhauled and partially repainted. Included accessories: - 1x Grinding wheel setup LEFT 500x80x203.2 mm - 1x Grinding wheel setup RIGHT 400x63x127 mm - 1x Internal grinding device Ø120 mm for 2 HF spindles (motor spindle and HF spindle) Center height: 225 mm Grinding head motor: drive power 9.2 kW B-AXIS: CNC-controlled B-axis KELCO 120: v constant 35 m/s or 45 m/s, speed of grinding spindle adjustable via CNC control (standard) Semi-automatic balancing device, ELASO, type EB 500 MFV 1230: high-frequency internal grinding spindle with oil-air lubrication High-performance motor spindle M34-FAVY100.R620-20/4 with permanent grease lubrication Balancing arbor Operating unit for MFV and MFZ spindles Hydraulic quill retraction for the tailstock Micro adjustment on the tailstock Pneumatic relief for the tailstock Tailstock park position Standard workpiece headstock MK5 CNC-controlled C-axis for standard workpiece headstock Sine bar for direct angle measurement using gauge blocks Wide adjustment, swivel-type base for the standard workpiece headstock Reinforced workpiece headstock MK5 CNC-controlled C-axis for reinforced workpiece headstock Fixed base for the reinforced workpiece headstock Coolant supply through the workpiece spindle Dressing device on lower table – with 2x 0053.05 and 2x 0053.20, located behind the workpiece headstock and tailstock Dressing device on upper table – with pos. 1x 0053.01, 1x 0053.03, 1x 0053.13 Preparation for later connection of the HF dressing unit for rotary dressing tools (RENAUD) Adapter plate for universal use of the HF dressing unit, internal and external KELPOS: active longitudinal positioning MOVOMATIC GAP: infeed sensor MOVOMATIC KELSET: tool measuring system KELSET, MARPOSS Gbsdpfxexflcre Acuju 1900 liters: endless belt filter with lift station, 100 l/min at 2.0 bar, designed for 2 machines Full enclosure Enclosure with service doors left and right Electrical interlock for the side door (grinding wheel change) Preparation for customer-side connection of a grinding mist extraction unit Chiller for cooling the H2O circuit (grinding head and HF spindle) Control cabinet lighting with door switch Data according to delivery note. All specifications subject to change without notice.

Sąlyga: naudotas, Grinding diameter: 450 mm Grinding length: 1000 mm Centre height: 225 mm As a globally leading company in Kellenberger overhauls and retrofits, we are not only capable of delivering machines in like-new quality with warranty, but can also provide ongoing service for your equipment. Machines are overhauled and delivered in accordance with the manufacturer’s standards. Photos shown are of previously delivered machines with additional options. Mechanical overhaul: - Complete overhaul of the entire machine per Kellenberger inspection protocol - New, maintenance-friendly enclosure - Newly painted Electrical overhaul: - New, state-of-the-art CNC cylindrical grinding machine control system - Completely refitted control cabinet - New drive technology - Replacement of all electrical wiring, Berus pressure switches, etc. - New absolute glass scales in X and Z axes - New absolute encoder (for B-axis) Photos of previously delivered machines with alternative configurations are available. Grinding head variant UR/RS: - Wheel arrangement for external and angular plunge grinding, wheels mounted in tandem - Enables use of 400 mm diameter grinding wheels for each operation Gbjdeuwv Hyepfx Acueu - Significantly reduced risk of collision - Simplified programming - Wheel specification: 400×63×127 mm (each) - Provision for operating a high-frequency spindle - Spindle available as optional extra - CNC-controlled B-axis for flexible external, face, and internal grinding in a single setup - Swivel range: +10° / -270° - C-axis for polygon grinding available as optional extra - Lower base fixed - Grinding head motor: 10.0 kW - Tailstock - Marposs measurement system for wheel profiling - Marposs longitudinal positioning system

Sąlyga: naudotas, Grinding diameter 350 mm Grinding length 1000 mm Center height 175 mm Space requirement approx. 3.6/3.5 m As the world’s leading company in Kellenberger overhauls/retrofits, we are not only able to deliver machines in as-new quality with warranty, but can also offer ongoing service for your machines: Kellenberger Kel-Varia series with Kelco 90 control system. Mechanical Overhaul: - Complete machine overhauled according to Kellenberger measuring protocol - New, service-friendly enclosure - New paintwork Electrical Overhaul: - New, state-of-the-art CNC cylindrical grinding machine control featuring the BEMA grinding interface - Completely rebuilt control cabinet - New drive technology - Replacement of all electrical cabling, pressure switches, etc. - New absolute glass scales in X and Z - New absolute rotary encoder (for B axis) Standard Equipment: - WSS with MK5 taper, optionally with MK5/short taper adapter - RST with MK4 taper, optionally with fine adjustment - Grinding spindle headstocks T1/T2/T3 - T1 grinding wheel diameter 400 mm - T2 grinding wheel diameter 300 mm - T3 internal grinding attachment, belt-driven via grinding spindle motor - Grinding spindle motor 4.4 kW - B axis high-resolution - Marposs measuring system for grinding wheel measurement - Longitudinal positioning with Marposs - GAP control (sensor on grinding spindle headstock), ELASO integrated into control interface - Semi-automatic balancing by ELASO integrated into control interface - BEMAT grinding wheel measurement Options at Extra Cost: - HF internal grinding spindle Godpouwv H Tjfx Acuobu - High-precision, maximum rigidity workpiece spindle headstock - Measuring control - Extraction unit - Paper band filter Control Functions: Basic Grinding Cycles - Zeroing the workpiece with Z-pos (longitudinal positioning) - Grinding wheel measurement with BEMAT - Touch sensor GAP - Measuring dressing diamonds - Corrections - External and internal cylindrical grinding (oscillation and plunge grinding) - External and internal taper grinding (B-axis swiveling, dressing with straight wheel) - External and internal radius grinding (radius dressed onto wheel) Optional Grinding Cycles - External and internal profile plunge grinding with profile wheel - External and internal profile grinding with straight wheel - Single and multi-start external and internal thread grinding with freely selectable flank angle - Trapezoidal thread grinding - Out-of-round grinding external and internal 15,000

Sąlyga: naudotas, Grinding diameter 350 mm Grinding length 1000 mm Centre height 175 mm Space requirement approx. 3.6/3.5 m As a world-leading company for Kellenberger overhaul/retrofit, we are not only able to deliver machines in as-new quality and with warranty, but can also offer you comprehensive service for your machines: Kellenberger Kel-Varia series with Kelco 90 control. Mechanical Overhaul: - Complete machine overhauled according to Kellenberger measurement protocol - New, service-friendly enclosure - New paintwork Electrical Overhaul: - New, modern CNC CYLINDRICAL GRINDING MACHINE control with BEMA grinding interface - Rebuilt control cabinet - New drive technology - Replacement of all electrical cabling, pressure switches, etc. - New absolute glass scales in X and Z axes - New absolute encoder (for B axis) Standard Equipment: - Workhead with MK5 taper, optionally with MK5/short taper adapter - Tailstock with MK4 taper. Optionally with fine adjustment - Grinding spindle stock T1/T2/T3 - T1 grinding wheel diameter 400 mm - T2 grinding wheel diameter 300 mm - T3 internal grinding attachment, belt-driven via grinding spindle motor - Grinding spindle motor 4.4 kW - High-resolution B axis - Marposs system for grinding wheel measurement - Longitudinal positioning Marposs - GAP control (sensor on grinding spindle stock) ELASO integrated into control interface - Semi-automatic balancing by ELASO integrated into control interface - BEMAT grinding wheel measurement Optional at extra cost: - HF internal grinding spindle - Ultra-precise, highly torsion-resistant workpiece spindle - Measuring control - Extraction unit - Paper band filter Control: Basic Grinding Cycles Gsdpfx Aouwv H Hocuebu - Workpiece zeroing with Z-position (longitudinal positioning) - Wheel measurement with BEMAT - Approach sensor GAP - Measurement of dressing diamonds - Corrections - External and internal cylindrical grinding (traverse and plunge grinding) - External and internal taper grinding (B axis swivel, dressing with straight wheel) - External and internal radius grinding (radius dressed onto the wheel) Optional Grinding Cycles - Profile plunge grinding external and internal with profile wheel - Profile grinding external and internal with straight wheel - Single and multi-start external and internal thread grinding with freely selectable flank angles - Trapezoidal thread grinding - Non-circular grinding external and internal 15,000

Sąlyga: naudotas, Gamybos metai: 2002, Grinding diameter: 450 mm Grinding length: 1500 mm Centre height: 225 mm Control system: FAGOR EQUIPMENT -T1: 500 mm grinding wheel diameter -T2: 400 mm grinding wheel diameter -T6: internal grinding attachment -T7: internal grinding attachment -Spindle motor, water-cooled, 9.8 kW -Marposs tool measurement system -Active longitudinal positioning -Kel-Set -GAP control on T1 and T2 by ELASO (contactless), integrated into the control interface -GAP control on T3/T4 via fluid sensor -Semi-automatic balancing by ELASO, integrated into the control interface for T1/T2 -Tailstock, hydraulic with fine adjustment +/-150 µm -Dressing device on the lower table, workpiece spindle side -Dressing device on the lower table, tailstock side -Dressing device on the upper table -New, service- and operator-friendly enclosure SPECIAL EQUIPMENT: Workpiece headstock with direct drive *highly recommended for non-circular grinding *max. workpiece weight, between centers: 150 kg *max. workpiece weight, overhung: 75 kg *water-cooled *Morse taper 5 combined with short taper mount to DIN 55026 *spindle orientation stop *fixed lower section B-axis with direct drive, center height 225 mm *extremely torsion-resistant *high positional accuracy *resolution ° *water-cooled MECHANICAL OVERHAUL: - Complete machine overhauled according to Kellenberger measurement protocol - New paintwork New hydraulic unit: - Improved temperature control (oil cooler) - Energy-saving: only one pump, and not running continuously! - Pressure monitoring - Monitoring of water content in the hydrostatic oil (early detection of bellows damage) Hydrostatic screw drive in X axis - Wear-free, since no contact during operation - No loss of accuracy, even during prolonged operation under full load at maximum speed - Friction-free at low speeds - No reversal jump of friction force when changing direction - Transmits smallest rotational movements - No stick-slip effect even at low speeds - No fluctuation in friction torque due to recirculating balls - Higher axial stiffness than ball screw drives - Significantly better damping, leading to improved workpiece surface and longer tool life - No vibrations due to recirculating balls - Also suitable for high speeds and accelerations - Cost-effective alternative to linear motors, offering higher accuracy and much less heating - Much lower power loss and thus no swarf issues on permanent magnets - Much lower cooling requirements compared to linear motors ELECTRICAL OVERHAUL: -New, modern CNC cylindrical grinding machine control with BEMA cylindrical grinding interface Gjdpfxsuxfu Ns Acuobu -Newly constructed control cabinet -New drive technology -Replacement of all electrical wiring (Berus pressure switches etc.) -New absolute glass scales in X and Z -New absolute encoder (for B-Axis) CONTROL SYSTEM: The grinding software consists of a base license and various options, depending on the machine configuration. Software base functions: - External and internal oscillation grinding - External and internal plunge grinding - External and internal plane oscillation grinding - External and internal plane plunge grinding - External and internal cone oscillation grinding - External and internal radius grinding (radius dressed on wheel) - Semi-automatic oscillation grinding - Workpiece...

Sąlyga: naudotas, Gamybos metai: 2004, Grinding diameter 350 mm Grinding length 1000 mm Centre height 175 mm Completely overhauled in 2018 Price includes maintenance and inspection protocol CNC-controlled radius dresser available at extra cost Grinding wheel equipment T1: 500x80x203.2 mm Grinding wheel equipment T2: 400x50x127 mm Internal grinding device 120 mm T3 for belt-driven internal grinding spindles Internal grinding spindle Fischer n max. 28,000 rpm Grinding head motor: Drive power 10.0 kW Kel-ASSIST 100, D/E/F, metric/inch B-axis: CNC-controlled for grinding heads with GRINDplusIT SS flange for 300, 400, 450 mm, bore 127 mm, 63 taper 1:10 SS flange for 450, 500 mm, bore 203.2 mm GRINDplusIT: v constant 35 m/s or 45 m/s Tailstock with manual retraction (standard) Micrometric adjustment on the tailstock Workpiece spindle head MK 5 DIN 55026 size 5" CNC-controlled C-axis for workpiece spindle head Base FIXED for the standard workpiece spindle head Coolant feed through the workpiece spindle Dressing device on the lower table, behind W-spindle head and tailstock KELPOS: Active longitudinal positioning MOVOMATIC, mounted on grinding head Special probe arm, curved, MOVOMATIC, probe stylus 6 mm KELSET: Tool measurement system KELSET, MARP KEL-TOUCH, infeed sensor Gbsdjw N Hhropfx Acuju Paper band filter USB with magnetic separator type SA 85/KE 585, Serial no.: BAF 663 Extraction unit IFMC 1800 All data subject to change without notice

Sąlyga: naudotas, Gamybos metai: 2002, Grinding diameter 350 mm Grinding length 1000 mm Centre height 175 mm Space requirement approx. 3.6 / 3.5 m Photos show identical machine with centre height 225 mm Base machine: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Standard equipment: - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - B-axis infinitely variable, high-resolution - Marposs measuring system for tool measurement - Active longitudinal positioning - GAP control on T1 and T2 by ELASO, contactless integration in the control interface - Semi-automatic balancing by ELASO, integrated in the control interface - Tailstock with manual retraction - Workpiece spindle head MK5 with short taper mount DIN 55026 - Internal grinding attachment, belt driven Options available at extra cost: - New high-precision workpiece spindle head with torque drive - Internal grinding attachment for high-frequency spindles, 120 mm diameter - HF internal grinding spindle Fischer MFM-1224/42/31 D-21 - HF spindle with HSK interface, 24,000 rpm with integrated GAP sensor (lead time applies) - CNC-controlled C-axis - Non-circular (polygon) grinding - Hydrostatic lead screw in X - New hydrostatic unit with only 1 pump and accumulator for improved energy efficiency - Monitoring of water content in the hydrostatic system - Extraction system Further options available on request Mechanical overhaul: - Complete machine overhauled in accordance with Kellenberger test protocol - New easy-maintenance enclosure - New paintwork Electrical overhaul: - New, modern CNC CYLINDRICAL GRINDER CONTROL with BEMA grinding interface - Newly built control cabinet - New drive technology - Replacement of all electrical wiring, pressure switches, etc. - New absolute glass scales in X and Z axes - New absolute rotary encoder (for B-axis) Control system: The grinding software consists of a basic license and various optional modules depending on the machine’s equipment. Basic software features: - External and internal oscillation grinding - External and internal plunge grinding - External and internal face oscillation grinding - External and internal face plunge grinding - External and internal cylindrical oscillation grinding - External and internal radius grinding, radius dressed on the wheel - Semi-automatic oscillation grinding - Workpiece zero setting - Wheel zero setting - Measurement of dressing diamonds - 2 form diamonds - 1 form diamond or dressing roll (dressing roll required) - Form roll (dressing roll required) - 3 flat dressing units - Corrections - Z-position measurement (probe required) - GAP contact (touching device required) Gjdpfxeuxfuco Acusbu OPTIONS available at extra cost: Profile plunge grinding software: - External and internal profile plunge grinding with profile wheel Profile grinding software: - External and internal profile grinding with straight wheel Thread grinding software: - Single- and multi-start external and internal thread grinding with profile dressed on the wheel - Dressing of single- and multi-rib wheels - Flank angle freely selectable Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-round plunge grinding: - External and internal non-round oscillation grinding Non-round grinding software: Precondition for non-round grinding is equipping the workpiece spindle with a high-resolution rotary encoder to enable operation as a C-axis. The non-round...

Sąlyga: naudotas, Grinding diameter 350 mm Gbodpfx Acjt Ii Rfoueu Grinding length 1500 mm Centre height 175 mm Left wheel 600 mm Grinding spindle head fixed, non-rotatable. Equipped with new FAGOR control system featuring BEMA cylindrical grinding interface. With new service-friendly enclosure. Completely overhauled according to Kellenberger measurement protocol.