Plokštės gręžimo staklės - Horizontaliosios

CERUTI ADM-ADL 125

Būklė: paruoštas naudoti (naudotas), The machine has been overhauled and is fully operational, complete with documentation. Rjdpfx Aefw Az Uof Aet

Būklė: naudotas, Eccentric Punching Press HAULICK + ROOS Type RVD 125 Double Column Eccentric Press Machine No. 212560 Year of manufacture: 1981 Pressing force: 125 tons Table size: 880 x 800 mm Table opening: 470 x 140 mm Column gap: 900 mm Side column spacing: 415 mm Ram stroke: 45 mm Ram adjustment: 0-80 mm Shut height as shown: 340 mm Strokes per minute: 50 to 300 spm Main drive motor power: 22 kW Power supply: 380 Volt, 50 Hz - Double connecting rod drive with 4-point eccentric shaft bearing for off-center ram force absorption - Free-standing electrical cabinet - NC roller feeder EBU, width 250 mm, year 2003 Rjdpfx Afshlnzke Ajt - Separate control panel for roller feed unit - Coil direction from left to right Space requirement (press) L x W x H: 3000 x 2000 x 3020 mm Transport height: 2950 mm Weight of press: approx. 11 tons

Būklė: paruoštas naudoti (naudotas), CAP30 DOZATORIUS 1000 HELICAP23: Pagaminimo metai: 2016 Versija: 300V Darbo valandos: 15 600 Kaina: 150 000 EUR FCA Lenkija Rsdpjw Nqn Nsfx Af Ajt Įrenginys buvo naudojamas gamyboje iki rugsėjo 20 d. Puiki būklė Puiki būklė, paruošta išsiuntimui.

Būklė: naudotas, Radial drilling machine CSEPEL Type RFh 75 / 1500 Machine No. 13704 Year of manufacture: 1985 Drilling capacity in steel Ø 75 mm Drilling capacity in cast iron Ø 90 mm Spindle taper MT 5 Nominal arm reach 1500 mm Maximum spindle reach 1500 mm (to column) Minimum spindle reach 440 mm (to column) Distance spindle nose – clamping surface 370 - 1700 mm Vertical adjustment of arm 950 mm Table size / clamping surface 1800 x 1100 mm Column diameter 450 mm Quill stroke 380 mm Rodslhwr Repfx Af Aot Spindle speed 19–1900 rpm, 21 steps Feed rate 0.047–2 mm/rev, 12 steps Motor power 11 kW Power supply 380 Volt, 50 Hz, 15 kW - Spindle clockwise/anticlockwise operation via hand lever switch - Hydraulic gearshift for spindle speed and feed rate - Hydro-mechanical central clamping - Motorized vertical arm adjustment - No coolant system - Machine lamp - Operating manual included Space required: Length 2720 mm x Width 1170 mm x Height max. 3770 mm Transport height with motor on column: 3500 mm Transport height without motor on column: 3250 mm Weight: 6.3 t Good condition

Būklė: naudotas, Gamybos metai: 1996, Funkcionalumas: visiškai funkcionalus, X ašies eiga: 10 000 mm, Y ašies eiga: 2 600 mm, Z ašies eigos atstumas: 700 mm, Hersteller: PAMA Modell: SPEEDRAM 1 CNC Baujahr: 1996 Spindel: 140 mm Querweg: 10.000 mm Vertikalweg: 2.600 mm Pinolenhub: 600 mm Pinolengröße: 360 x 320 mm Spindelhub: 700 mm Spindelaufnahme: ISO 50 Rodswzh Apepfx Af Aet Spindelmotorleistung: 50 kW Spindeldrehzahlen: 6 – 2.000 U/min CNC-Steuerung: SELCA 3045 Werkzeugwechsler (ATC): 60 Plätze Gesamtgewicht: 65 Tonnen Ausstattung und Zubehör Komplett mit: - 1 automatischer Universalfräskopf - 1 Bodenplatte 6.000 x 2.500 x 300 mm - 1 Bodenplatte 4.500 x 2.000 x 300 mm - Rundtisch 2.000 x 1.600 mm, mit Längsweg 2.000 mm - Tischbelastung: 15 t - Nivellierfüße

Būklė: naudotas, Gamybos metai: 1974, Wheel diameter - max. 400 mm Wheel width 75 mm Total power requirement 25 kW Machine weight approx. 7 t LORENZ High-Performance Gear Shaping Machine Model LS 400 Year of manufacture 1975 S/N 12592 _____ Max. external gear diameter 400 mm * (possibly larger) Max. internal gear diameter approx. 350 mm Max. gear width 75 mm Module range 0.5 - 6 Stroke length 82 mm Stroke position adjustment 0 - 100 mm Distance from shaping spindle to machine body 205 mm Spindle taper approx. MK 5 Strokes per minute roughing/finishing 118 - 1,000 /min. Table size 400 mm Table bore 125 mm Rsdpot Hww Dofx Af Ast Installation height between table and shaping head min./max. 190/290 mm Fixed distance shaping spindle 250 mm Table axial travel approx. 295 mm Number of teeth approx. 12 - 150 Feed range Tooth depth 0.01 - 0.063 mm /stroke -"- Radial feed at tool-Ø 125 0.125 - 3.150 mm /stroke Spindle / total drive approx. 19 kW / 25 kW - 380 V - 50 Hz Weight 7,000 kg Accessories / Special equipment: • Hydrostatically guided slideway with separate hydraulic unit • Built-in intermediate plate 100 mm to increase shaping head height • Hydraulic workpiece clamping system, brand RINGSPANN, integrated in the table for flat components and internal clamping, various clamping chucks for different workpiece diameters • Infinitely variable stroke speed adjustment for roughing and finishing (SIMOREG DC-Master) • Automatic stroke speed change and automatic feed change for roughing and finishing in up to 3 cuts • Automatic and motor-driven stroke position locking at top dead center after finishing • Separate control cabinet • Integrated coolant system with chip conveyor and magnetic separator • Approx. 20 change gears Condition: Satisfactory to good, shortly demonstration-ready Delivery: Ex stock – as inspected Payment: Net – upon receipt of invoice

Būklė: labai geros būklės (naudotas), Manufacturer: HEYLIGENSTAEDT Model: NDC 710 / 1800 Control: R&D MTC3 4-jaw chuck 1400 mm Steady rests: 3 units, Ø 100–1050 mm Roller steady rests: 2 units, open type, Ø 1120 mm KNOLL chip conveyor, year 2022 Boring bar Ø 260 x 3500 mm Boring bar Ø 200 x 1500 mm Boring bar Ø 150 x 1100 mm Turning length: 8250 mm Swing over bed Ø: 1400 mm Swing over cross slide: 1120 mm Spindle power: 100 kW Workpiece weight: 16,000 kg Redpfx Aswzh A Aef Ast Length: 14,000 mm Width: 3,500 mm Height: 2,900 mm Weight: 32,000 kg

Būklė: naudotas, Gamybos metai: 1988, Sūkių skersmuo virš staklių lovos 2000 mm Sūkių skersmuo virš atramos / mm Sukimosi ilgis / mm - Tipas 1 K 671 320 F3 - Pagaminimo metai 1988 (pirmasis paleidimas 1998) - Sukimosi ilgis 10.000 mm - Sūkių skersmuo virš lovos 2.000 mm (modifikuota) - Veido plokštės skersmuo 1.950 mm - Veido plokštės spaudimo diapazonas 400 - 1.350 mm - Sukimosi greičiai 1,00 - 140 aps./min. - Sukimo momentas 125.000 Nm - Didžiausia pagrindinė pjovimo jėga 130 kN - Automatinis gręžtuvo įjungimas - Didžiausias ruošinio svoris 70 t - Didžiausias ruošinio svoris su suportu 100 t - Pagrindinio variklio galia 100 kW - Lovoje bėgių skaičius 4 - Matmenys 22.000 x 6.200 x 2.900 mm - CNC valdymas SIEMENS 840D (2010 už 220.000,00 €) - Atramos pastūma X-Z 0,3 - 4.000 mm/min. - Atramos greita pastūma X-Z 4.000 mm/min. Redpfx Afsxn Tz Ij Aet - Vidinės kūgio matmenys 140 x 1:7 - Staklės atitinka CE direktyvas - Įskaitant 2 lunetes, 1 ritininį stovą, 4 žnyples, išteisinimo įrenginį - Būklė: labai gera būklė

Gamybos metai: 2007, būklė: naudotas, Dantytės skersmuo - išorinis dantratukas: 1200 mm Dantytės skersmuo - vidinis dantratukas: 1200 mm Dantytės plotis - maks.: 260 mm Valdymas: Liebherr PC-NC Detalės skersmuo - maks.: 1500 mm Stalo skersmuo: 900 mm Stalo kiaurymės skersmuo: 320 mm Maks. stalo apkrova: 95 kN Variklio galia: 30 kW Aušinimo skysčio siurblys: 120 l/min Ašies atstumas tarp stūmoklio ir ruošinio stalo: 0–820 mm Stūmoklio skersmuo: 125 mm Įrankio laikiklis: SK 45 DIN Staklių svoris apie: 26 t Užimama vieta apie: 8,073 x 6,183 x 4,375 m Judėsiai: - Judesio ilgis min./maks.: 0 mm / 270 mm - Judesio ilgio reguliavimas: 270 mm - Judesių skaičius (dvigubas judesys): 10–270 DH/min Įranga/Priedai: - Drožlių transporteris - Pjovimo galvutės laikiklis SK 45 DIN Redpfxew Rf S Ee Af Ast - Aušintuvas - Techninė dokumentacija

Būklė: naudotas, Gamybos metai: 1965, Max. core drilling diameter: 50 mm Drilling depth: 2,000 mm Swing diameter: mm Max. drilling diameter: 110 mm Total power requirement: 30 kW Machine weight approx.: 10 t Year of manufacture: 1965 Overhauled: 2000 Drilling Ø - solid drilling approx. 2 - 50 mm - boring approx. 100 mm Max. drilling depth: 1,600 / up to 2,000 mm (see stroke/installation length) Drill carriage stroke approx.: 4,000 mm Distance between spindle heads: 5,000 mm Center height over guideways: 350/450 mm Rodpfx Aot Hwucof Aet Drill carriage feed, infinitely variable: 20 - 200 mm/min Rapid feed of drill carriage: 2,500 mm/min Workpiece speeds via belt drive: 260 - 650 / 650 - 1,625 rpm Working spindle drive: 24 kW Coolant pump drives: 1 x 7.5/15 kW, 1 x 15/28 kW Total drive approx. 60 kW, 380 V – 50 Hz Overall machine/guideway length: 7,500 / 5,000 mm Total weight approx.: 10,000 kg Accessories / Special features: - Machine consists of the following elements: Main spindle on the left side, followed by a BOZA, powered table assembly with ball screw, BOZA with increased center height, and a spindle stock of the B 16 series with drive motor approx. 7.5 kW, n = 900/2,400 and 2,400/6,000 rpm. Very large and elaborate coolant system with filter unit, extensive accessories and drilling tools up to 100 mm Ø. - Suitable for rotating workpiece/fixed drilling tool (ELB and BTA methods), as well as for stationary workpiece and rotating drilling tool. Internal (ELB) as well as external oil supply (BTA) possible. - Complete coolant system with tank and filter, 2 high-pressure pumps by SIG, adjustable flow rates: 17/40/120 and 220/500 L/min; capacity approx. 2,500 L. - Carriage feed via ball screw and infinitely adjustable DC motor; mounted table cross-adjustable approx. 500 mm, table approx. 800 x 800 mm for clamping cubic and cylindrical workpieces. Electrically controlled via cam track approx. 2,500 mm and limit switches for rapid traverse, feed, and return. - 2 closed 3-point steady rests, FORKHARDT 3-jaw manual chuck approx. 315 mm Ø. - Modernized control panel with speed display, feed adjustment and indication, kW display, feed/rapid traverse selection (left/right), etc. - 2 separate control cabinets, separate BOZA, sleeves, adapters, clamping aids, and much more. Condition: Good – ready for demonstration soon; machine is highly valuable due to accessories Delivery: Ex stock – as inspected Payment: Net – upon receipt of invoice Further deep hole drilling machines constantly in stock – please inquire with us.